Search NASA⌕ Search

SEARCH · Search NASA

Results for “shock wave research”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Pressure-sensing performance of upright cylinders in a Mach 10 boundary-layer

An experimental research program to provide basic knowledge of the pressure-sensing performance of upright, flushported cylinders in a hypersonic boundary layer is described. Three upright cylinders of 0.25-, 0.5- and l.0-in. diameters and a conventional rake were placed in the test section sidewall boundary layer of the 31 Inch Mach 10 Wind Tunnel at NASA Langley Research Center, Hampton, Virginia. Boundary-layer pressures from these cylinders were compared to those measured with a conventional rake. A boundary-layer thickness-to-cylinder-diameter ratio of 8 proved sufficient to accurately measure an overall pressure profile and ascertain the boundary-layer thickness. Effects of Reynolds number, flow angularity, and shock wave impingement on pressure measurement were also investigated. Although Reynolds number effects were negligible at the conditions studied, flow angularity above 10 deg significantly affects the measured pressures. Shock wave impingement was used to investigate orifice-to-orifice pressure crosstalk. No crosstalk was measured. The lower pressure measured above the oblique shock wave impingement showed no influence of the higher pressure generated at the lower port locations.

Johnson, Steven↗
NASA NTRS1995

Experimental investigation of the inlet detector configuration variation in the flow field at Mach 1.9

In recent years, active research has been conducted to study the technological feasibility of supersonic laminar flow control on the wing of the High Speed Civil Transport (HSCT). For this study, the F-16XL has been chosen due to its highly swept crank wing planform that closely resembles the HSCT configurations. During flights, it is discovered that the shock wave generated from the aircraft inlet introduces disturbances on the wing where the data acquisition is conducted. The flow field about a supersonic inlet is characterized by a complex three dimensional pattern of shock waves generated by the geometrical configuration of a deflector and a cowl lip. Hence, in this study, experimental method is employed to investigate the effects of the variation of deflector configuration on the flow field, and consequently, the possibility of diverting the incoming shock-disturbances away from the test section. In the present experiments, a model composed of a simple circular tube with a triangular deflector is designed to study the deflector length and the deflector base width variation in the flow field. Experimental results indicate that the lowest external pressure ratio is observed at the junction where the deflector lip and the inlet cowl lip merge. Also, it is noted that the external pressure ratio, the internal pressure ratio, the coefficient of spillage drag, and the shock standoff distance decrease as the deflector length increases. In addition, the Redefined Total Pressure Recovery Ratio (RTPRR) increases with an increase in the deflector length. Results from the study of the effect of the deflector's base width variation on the flow field indicate that the lowest external pressure ratio is observed at the junction between the inlet cowl lip and the deflector lip. As the base width of the deflector increases, the external pressure ratio at 0 rotation increases, whereas the external pressure ratio at 180 rotation decreases. In addition, the internal pressure ratio and the coefficient of spillage drag decrease as the base width of the deflector increases. However, RTPRR and shock standoff distance increase as the base width increases. In conclusion, as deflector dimensions vary, distinctive patterns in the pressure variation around the inlet deflector are observed. With an increase in the deflector length and base width, the magnitude of shock-disturbances are weakened due to a decrease in the external pressure ratio. Also, as the deflector length and base width increase, a smaller bow shock angle is formed. Therefore, the inlet shock wave formation would be significantly altered, and consequently, shock disturbances on the wing test section can be avoided through appropriately designing the deflector.

Hwang, Kyu C.↗
NASA NTRS1987

Waves and instabilities

The U.S research activities during the mid-1982 to mid-1986 period in the area of plasma waves and instabilities are described. The principal results obtained by satellite observations and theoretical research can be divided into the following six categories: (1) whistler-mode wave-electron interactions, (2) wave-induced particle precipitation, (3) ULF wave phenomena, (4) ion-mode waves and instabilities, (5) auroral kilometric radiation, and (6) ionospheric irregularities and instabilities. In addition, waves and instabilities found in the outer magnetosphere, including the geomagnetic tail, magnetopause, and bow shock regions, are briefly discussed.

Inan, Umran S.↗
NASA NTRS2019

Technology Development and Infusion by NASA's Entry Systems Modeling Project

This paper describes recent development of modeling and simulation technologies for entry systems and their infusion into NASA's exploration missions. Technology development is organized and prioritized using a system-level perspective, resulting in four broad technical areas of investment: (1) Thermal protection material modeling, (2) Shock layer kinetics and radiation, (3) Computational and experimental aerosciences, and (4) Guidance, navigation, and control. The paper will highlight key contributions from each of these areas, their impacts from a spacecraft and mission design perspective, and discuss planned future investment. Aspects of each technical area are only briefly summarized here. Thermal protection material modeling is geared toward high-fidelity, predictive models capable of optimizing design performance, post-flight reconstruction, and quantifying thermal protection system reliability. New computational tools and experimental techniques have been applied to Orion, MSL/Mars 2020, Mars InSight, and Mars Sample Return missions. Research and development in the area of shock layer kinetics has focused on air and CO2-based atmospheres. In both cases, substantial improvements in model uncertainty have directly impacted the development of mission margin policies, flight instrumentation design and analysis (Orion and Mars 2020), and have even revealed the importance of neglected phenomena like mid-wave infrared radiation of CO2. Aerosciences is a very broad area of interest in entry systems, yet a number of important challenges are being addressed: Coupled fluid-structure simulations of parachute inflation and dynamics affecting Orion, Commercial Crew, and Mars programs; Experimental and computational studies of vehicle dynamics; Multi-phase flow with dust particles to simulate augmentation of aerothermal environments at Mars during dust storms; and studies of roughness-induced heating augmentation relevant to tiled (Orion, Mars 2020) and woven (Mars Sample Return) thermal protection systems. Guidance and control in the context of entry systems has focused on development of methods for multi-axis control (i.e. pitch and yaw, rather than bank angle alone) of spacecraft during entry and descent, with precision landing requirements driven by Mars human exploration goals.

Barnhardt, Michael D.↗
NASA NTRS1995

Studies on Equatorial Shock Formation During Plasmaspheric Refilling

During the grant period from August 1, 1994 to October 31, 1995 we have continued to investigate the effects of plasma wave instabilities on the early stage plasmaspheric refilling. Since ion beams are the primary feature of the interhemispheric plasma flows during the early stage refilling, ion-beam driven instabilities and associated waves are of primary interest. The major findings of this research are briefly summarized here. After a systematic examination of the relevant plasma instabilities, we realized that when the interhemispheric plasma flows begin to interpenetrate at the equator, the most relevant plasma instability is the electrostatic ion cyclotron wave instability. Only at later stages the ion-acoustic instability may be affecting the plasma flow. An interesting property of the electrostatic ion cyclotron wave is that it heats ions perpendicular to the magnetic field. When the ions in the field-aligned flows are transversely heated, they are trapped in the magnetic flux tube, thus affecting the refilling process. The eic wave instability is a microprocess with scale length of the order of ion Larmor radius and the corresponding time scale is the ion cyclotron period. We have attempted to tackle the problem for the plasmaspheric refilling by incorporating the effects of eic wave instability on the mesoscale plasma flow when the properties of the latter exceeds the critical conditions for the former. We have compared the results on refilling from the model with and without the eic instability effects.

Singh, Nagendra↗
NASA NTRS1993

An experimental study of the sources of fluctuating pressure loads beneath swept shock/boundary-layer interactions

An experimental research program providing basic knowledge and establishing a database on the fluctuating pressure loads produced on aerodynamic surfaces beneath three dimensional shock wave/boundary layer interactions is described. Such loads constitute a fundamental problem of critical concern to future supersonic and hypersonic flight vehicles. A turbulent boundary layer on a flat plate is subjected to interactions with swept planar shock waves generated by sharp fins at angle of attack. Fin angles from 10 to 20 deg at freestream Mach numbers of 3 and 4 produce a variety of interaction strengths from weak to very strong. Miniature Kulite pressure transducers flush-mounted in the flat plate are used to measure interaction-induced wall pressure fluctuations. The distributions of properties of the pressure fluctuations, such as their ring levels, amplitude distributions, and power spectra, are also determined. Measurements were made for the first time in the aft regions of these interactions, revealing fluctuating pressure levels as high as 160 dB. These fluctuations are dominated by low frequency (0-5 kHz) signals. The maximum ring levels in the interactions show an increasing trend with increasing interaction strength. On the other hand, the maximum ring levels in the forward portion of the interactions decrease linearly with increasing interaction sweep back. These ring pressure distributions and spectra are correlated with the features of the interaction flowfield. The unsteadiness of the off-surface flowfield is studied using a new, non-intrusive technique based on the shadow graph method. The results indicate that the entire lambda-shock structure generated by the interaction undergoes relatively low-frequency oscillations. Some regions where particularly strong fluctuations are generated were identified. Fluctuating pressure measurements are also made along the line of symmetry of an axisymmetric jet impinging upon a flat plate at an angle. This flow was chosen as a simple analog to the impinging jet region found in the rear portion of the shock wave/boundary layer interactions under study. It is found that a sharp peak in ring pressure level exists at or near the mean stagnation point. It is suggested that the phenomena responsible for this peak may be active in the swept interactions as well, and may cause the extremely high fluctuating pressures observed in the impinging jet region in the present experimental program.

Settles, G. S.↗
NASA NTRS1975

International Symposium on Combustion, 15th, Tokyo, Japan, August 25-31, 1974, Proceedings

Recent theoretical and experimental studies concerned with detonation and pressure wave combustion interaction, fire and explosion research and safety, heterogeneous combustion, flame-flow interactions, kinetics of elementary reactions, pollution control in and by combustion systems, and ignition are presented. Some of the topics covered include critical power density for direct initiation of unconfined gaseous detonations, extinction of laminar diffusion flames for liquid fuels, combustion of bulk titanium in oxygen, flame propagation in small spheres of unconfined and slightly confined flammable mixtures, kinetics of the reaction of nitric oxide with hydrogen, production of chemi-ions and formation of CH and CH2 radicals in methane-oxygen and ethylene-oxygen flames, NOx emission characteristics in two-stage combustion, and spherical ignition of oxyhydrogen behind a reflected shock wave. Individual items are announced in this issue.

Source record↗
NASA NTRS2001

Numerical Simulation of One- and Two-Phase Flows in Propulsion Systems

In this report, we present some results of problems investigated during joint research between the Hampton University Fluid Mechanics and Acoustics Laboratory (HU/FM&AL), NASA GRC, and the LaRC Hyper-X Program. This work is supported by joint research between the NASA GRC and the Institute of Mechanics at Moscow State University (IM/MSU) in Russia under a CRDF grant. The main areas of current scientific interest of the HU/FM&AL include an investigation of the proposed and patented advanced methods for aircraft engine thrust and noise benefits. These methods are based on nontraditional 3D corrugated and composite nozzle, inlet, propeller and screw designs such as a Bluebell and Telescope nozzle, Mobius-shaped screw, etc. This is the main subject of our other projects, of which one is presented at the current conference. Here we analyze additional methods for exhaust jet noise reduction without essential thrust loss and even with thrust augmentation. Such additional approaches are: (1) to add some solid, fluid, or gas mass at discrete locations to the main supersonic gas stream to minimize the negative influence of strong shock waves formed in propulsion systems. This mass addition may be accompanied by heat addition to the main stream as a result of the fuel combustion or by cooling of this stream as a result of the liquid mass evaporation and boiling; (2) Use of porous or permeable nozzles and additional shells at the nozzle exit for preliminary cooling of the hot jet exhaust and pressure compensation for off-design conditions (so-called continuous ejector with small mass flow rate); and (3) to propose and analyze new effective methods of fuel injection into the flow stream in air-breathing engines. The research is focused on a wide regime of problems in the propulsion field as well as in experimental testing and theoretical and numerical simulation analyses for advanced aircraft and rocket engines. The FM&AL Team uses analytical methods, numerical simulations, and experimental tests at the Hampton University campus, NASA, and IM/MSU. The main outcomes during this reporting period are: (1) Publications: The AIAA Paper #01-1893 has been accepted for the AIAA/NAL-NASDA-ISAS 10th International Space Planes and Hypersonic Systems and Technologies Conference, 24-27 April 2001, Kyoto, Japan. The AIAA Paper #01-3204 has been accepted for presentation at the 37th AIAA/ASME/SAE/ASEE Joint Propulsion Conference being held on 08-11 July, in Salt Lake City, UT; (2) Grants and proposals: The HU/FM&AL was awarded the NASA grant NAG3-2495 in October 2000 and the CRDF award was granted to the NASA GRC-HU FM&AL and IM/MSU (Russia) in July 2000. A solicited proposal was submitted for the NASA NRA-01GRC-02 competition and two unsolicited proposals to NASA are in preparation; (3) Theory and numerical simulations: Analytical theory, numerical simulation, comparison of theoretical with experimental results, and modification of theoretical approaches, models, grids, etc. Such investigations have been conducted for three main problems: (a) Combustion efficiency optimization in the half-duct combustor system; (b) Drag reduction effects for blunt bodies with solid needles; and (c) Solid particle injection from the butt-end against a supersonic flow. The NASA CFL3D, HU/FM&AL, and IM/MSU GODUNOV codes were used and modified for solution of these problems. The codes are based on full Euler and Navier-Stokes solvers with and without nonequilibrium oxygen-nitrogen and air-hydrogen chemical reactions in laminar and turbulent gas flow regimes; (4) Experimental tests: In the IM/MSU supersonic wind tunnel, experimental tests were conducted with different number, location, and geometric parameters of solid needles mounted at the front of the butt-end in supersonic flow. Optimal parameters were determined that provide minimal butt-end drag in the stationary flow regime. Experimental and numerical simulation results are in good agreement; (5) Student Research Activity: Involvement of one graduate and two undergraduate students as research assistants in the current project.

Gilinsky, Mikhail↗
NASA NTRS1996

[?]Nonlinear Issues in the Aerothermochemistry of Gases and Materials and the Associated Physics and Dynamics of Interfaces

Our research and technology are focused on nonlinear issues in the aerothermochemistry of gases and materials and the associated physics and dynamics of interfaces. Our program is now organized to aggressively support the NASA Aeronautics Enterprise so as to: (a) develop a new generation of environmentally compatible, economic subsonic aircraft; (b) develop the technology base for an economically viable and environmentally compatible high-speed civil transport; (c) develop the technology options for new capabilities in high-performance aircraft; (d) develop hypersonic technologies for air-breathing flight; and (e) develop advanced concepts, understanding of physical phenomena, and theoretical, experimental, and computational tools for advanced aerospace systems. The implications from our research for aeronautical and aerospace technology have been both broad and deep. For example, using advanced computational techniques, we have determined exact solutions for the Schrodinger equation in electron-molecule scattering allowing us to evaluate atmospheric models important to reentry physics. We have also found a new class of exact solutions for the Navier Stokes equations. In experimental fluid dynamics, we have found explicit evidence of turbulence modification of droplet sizes in shock tube flow with condensation. We have developed a new diagnostic tool for the direct estimation of flow velocities at MHz sampling rates in quasi-one dimensional turbulent flow. This procedure suggests an unexpected confirmation of the possibility of 'natural' closure in Reynolds stresses with deep implications for the development of turbulent models. A transient increase is observed in both the spectral energy decay rate and the degree of chaotic complexity at the interface of a shock wave and a turbulent ionized gas. Even though the gas is apparently brought to rest by the shock wave, no evidence is found either of the expected relaminarization. A unique diamond-shaped nozzle has been designed for a detailed investigation of the effect of significant streamwise vorticity on the acoustic and IR characteristics of supersonic jets. Our results provide convincing evidence of the significant effect of vorticity on the far-field noise for the diamond jet as compared to the conventional round jets. We have found that the countercurrent shear layer mixes much more efficiently than conventional coflowing shear layers. We also developed the fluid thrust vectoring procedures which use counter flow to vector a jet. Our materials research has shown that the steep stress gradients at the fiber-matrix interface could be the primary cause of interface cracks after the processing of metallic and intermetallic matrix composites. New techniques have been evolved for: the microcharacterization of materials including microplastic strain and, point by point, the misorientation and plasticity for matrix composites; thermally induced stress measurements and load relaxation; the growth and characterization of metallic matrix composite interfaces; and for the growth of ferrite materials by pulsed laser deposition. The FAMU commitment to the HBCU Research Center also continues to be broad and deep.

Johnson, Joseph A., III↗
NASA NTRSDate not supplied

Tracing the Cosmic Energy Flow with Parker Solar Probe: Universal Processes

Heliophysics is inherently interdisciplinary, born from multiple subjects to understand how the Sun interacts with its surrounding environment. Heliophysicists and Astrophysicists seldom exchange ideas since the scientific infrastructure partitions research areas by spatial location in the cosmos. Parker Solar Probe (PSP) is sending back puzzling information in regions we have never been before, presenting an opportunity to search for answers in non-traditional ways that are inherently cross-disciplinary. The fundamental processes that govern the physics of the universe, such as wave-particle interactions, turbulence, magnetic reconnection, and shocks, are mechanisms to study cosmic energy flow. We present PSP observations that may enable us to assess the universality of these fundamental processes in – and across boundaries of –various space and astrophysical regimes. Specifically, we focus on the exotic shapes of proton velocity distribution functions and subsequent evolution leading to multi-scale wave generation and particle acceleration. We welcome ideas, tools, and methodologies from all disciplines to understand the systems of systems governing our universe.

J L Verniero↗
NASA NTRS1978

Plasma waves near the sun: Advances possible with a solar probe

A review is presented of current experimental and theoretical knowledge of plasma waves in the solar wind, with comments on the scientific importance of obtaining plasma wave measurements in the region near the sun with the solar probe. The waves discussed include the acoustic waves and shocks which are thought to be the primary source for heating the solar corona, Alfven waves, ion-cyclotron waves, whistler-mode turbulence, ion-acoustic waves, and electron plasma oscillations associated with solar radio emissions. A discussion is presented of the types of measurements which would be needed to study these waves on the solar probe, the constraints imposed on the spacecraft and the research and development which would be needed to provide the necessary instrumentation.

Gurnett, D. A.↗
NASA NTRS1985

Computations of unsteady transonic flows

During the last eight years, the subject of computational unsteady transonic aerodynamics has undergone a period of rapid growth. A brief survey of some of the fundamental advances during this period is provided, and some of the research done at NASA Ames Research Center is described in detail. The small-distance potential equation is considered, taking into account features of the unsteady transonic flow, the governing equation, the pressure coefficient, the wake condition, the airfoil tangency condition, the downstream boundary condition, the alternating direction implicit (ADI) algorithm, a grid system, boundary conditions, an airfoil with oscillating trailing edge flap, three types of shock-wave motion, and an example of a simple aeroelastic problem. A description is given of an implicit algorithm for the unsteady full potential equation in conservation form.

Goorjian, P. M.↗
NASA NTRS1990

Limitations of the method of characteristics when applied to axisymmetric hypersonic nozzle design

A design study of axisymmetric hypersonic wind tunnel nozzles was initiated by NASA Langley Research Center with the objective of improving the flow quality of their ground test facilities. Nozzles for Mach 6 air, Mach 13.5 nitrogen, and Mach 17 nitrogen were designed using the Method of Characteristics/Boundary Layer (MOC/BL) approach and were analyzed with a Navier-Stokes solver. Results of the analysis agreed well with design for the Mach 6 case, but revealed oblique shock waves of increasing strength originating from near the inflection point of the Mach 13.5 and Mach 17 nozzles. The findings indicate that the MOC/BL design method has a fundamental limitation that occurs at some Mach number between 6 an 13.5. In order to define the limitation more exactly and attempt to discover the cause, a parametric study of hypersonic ideal air nozzles designed with the current MOC/BL method was done. Results of this study indicate that, while stagnations conditions have a moderate affect on the upper limit of the method, the method fails at Mach numbers above 8.0.

Edwards, Anne C.↗
NASA NTRS1986

Transonic potential flow in hyperbolic nozzles

The full potential equation for the classical problem of transonic flow through a hyperbolic nozzle (with or without a shock wave) is solved in conservation form using the finite volume method of Jameson and Caughey (1977). Either a firstor a second-order numerical viscosity is added in the direction of the flow, explicitly, in conservation form. A multigrid alternating direction implicit method is used to solve the difference equations, and the results obtained are compared with analytical and numerical results from previous researches.

Park, M.↗
NASA NTRS1998

Particle Imaging Velocimetry Used in a Transonic Compressor Facility

Particle Imaging Velocimetry (PIV) is an optical technique whereby a pulsed laser sheet is used to illuminate particles entrained in a fluid across an extended planar cross section of a flow field. Electronic recording of the particle positions at two closely timed laser pulses permits the computation of the flow velocity. PIV captures the instantaneous flow field, permitting the study of unsteady flow phenomena. Mean flow statistics can be computed by acquiring several hundred images and averaging the results. The first-ever successful application of PIV to acquire measurements in a high-speed rotating turbomachinery blade row was completed in NASA Lewis Research Center's W-8 Single Stage Axial Compressor Facility. Measurements were acquired in a 20-in.-diameter transonic compressor rotor operating at 17,188 rpm. A custom-designed light-sheet generating probe was used to insert the high-energy, pulsed light-sheet illumination required for recording the unblurred images of particles entrained in the fluid. Measurements of the shock wave formed within the rotor blade passage and of unsteady structures within the blade wakes were acquired. These measurements provide insight into unsteady spatial structures in the flow field which cannot be measured with the more conventional laser anemometry technique. The PIV technique provides both instantaneous and average velocity data in a transonic compressor in an order of magnitude less time than required for other conventional optical diagnostic techniques.

Wernet, Mark P.↗
NASA NTRS2007

Flight Testing of the Gulfstream Quiet Spike(TradeMark) on a NASA F-15B

Gulfstream Aerospace has long been interested in the development of an economically viable supersonic business jet (SBJ). A design requirement for such an aircraft is the ability for unrestricted supersonic flight over land. Although independent studies continue to substantiate that a market for a SBJ exists, regulatory and public acceptance challenges still remain for supersonic operation over land. The largest technical barrier to achieving this goal is sonic boom attenuation. Gulfstream's attention has been focused on fundamental research into sonic boom suppression for several years. This research was conducted in partnership with the NASA Aeronautics Research Mission Directorate (ARMD) supersonic airframe cruise efficiency technical challenge. The Quiet Spike, a multi-stage telescopic nose boom and a Gulfstream-patented design (references 1 and 2), was developed to address the sonic boom attenuation challenge and validate the technical feasibility of a morphing fuselage. The Quiet Spike Flight Test Program represents a major step into supersonic technology development for sonic boom suppression. The Gulfstream Aerospace Quiet Spike was designed to reduce the sonic boom signature of the forward fuselage for an aircraft flying at supersonic speeds. In 2004, the Quiet Spike Flight Test Program was conceived by Gulfstream and NASA to demonstrate the feasibility of sonic boom mitigation and centered on the structural and mechanical viability of the translating test article design. Research testing of the Quiet Spike consisted of numerous ground and flight operations. Each step in the process had unique objectives, and involved numerous test team members from the NASA Dryden Flight Research Center (DFRC) and Gulfstream Aerospace. Flight testing of the Quiet Spike was conducted at the NASA Dryden Flight Research Center on an F-15B aircraft from August, 2006, to February, 2007. During this period, the Quiet Spike was flown at supersonic speeds up to Mach 1.8 at the maximum design dynamic pressure of 685 pounds per square foot. Extension and retraction tests were conducted at speeds up to Mach 1.4. The design of the Quiet Spike to shape the forward shock wave environment of the aircraft was confirmed during near-field shock wave probing at Mach 1.4. Thirty-two flights were performed without incident and all project objectives were achieved. The success of the Quiet Spike Flight Test Program represents an important step towards developing commercial aircraft capable of supersonic flight over land within the continental United States and in international airspace.

Smolka, James W.↗
NASA NTRS1987

A new algorithm for the Navier-Stokes equations applied to transonic flows over wings

A new algorithm has been developed for the Navier-Stokes equations. For the convective terms, this algorithm employs flux vector splitting together with a locally rotated coordinate system that is aligned with the streamwise direction. The algorithm has been implemented into a Navier-Stokes code, the NASA Ames Research Center's TNS code, and several cases of steady flow have been calculated. The results show improvements over the original method in the code. First, in a case of separated flow, there is better agreement with the experimental results and also there is an absence of numerical oscillations that occur with the original method. Second, in a case with a strong supersonic to subsonic shock wave, comparisons show an improvement in the resolution of the shock wave and the reexpansion singularity.

Goorjian, Peter M.↗
NASA NTRS1990

CO mapping of the nuclear region of NGC 6946 and IC 342 with Nobeyama millimeter array

CO observations of nearby galaxies with nuclear active star forming regions (and starburst galaxies) with angular resolutions around 7 seconds revealed that molecular bars with a length of a few kiloparsecs have been formed in the central regions of the galaxies. The molecular bar is interpreted as part of shock waves induced by an oval or barred potential field. By shock dissipation or dissipative cloud-cloud collisions, the molecular gas gains an infall motion and the nuclear star formation activity is fueled. But the distribution and kinematics of the molecular gas in the nuclear regions, which are sites of active star formation, remain unknown. Higher angular resolutions are needed to investigate the gas in the nuclear regions. Researchers made aperture synthesis observations of the nuclear region of the late-type spiral galaxies NGC 6946 and IC 342 with resolutions of 7.6 seconds x 4.2 seconds (P.A. = 147 deg) and 2.4 seconds x 2.3 seconds (P.A. = 149 deg), respectively. The distances to NGC 6496 and IC 342 are assumed to be 5.5 Mpc and 3.9 Mpc, respectively. Researchers have found 100-300 pc nuclear gas disk and ring inside a few kpc molecular gas bars. Researchers present the results of the observations and propose a possible mechanism of active star formation in the nuclear region.

Ishizuki, Sumio↗