Search NASA⌕ Search

SEARCH · Search NASA

Results for “simulation facilities”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Propulsion test facilities - Capabilities and use

A review is conducted of the additional test facilities required in connection with the National Aeronautical Facilities Program and of other new propulsion test facilities. Attention is given to the National Transonic Facility, the AMES wind tunnel, the Turbine Engine Load Simulator, facilities for the conduction of compressor research, a fuels and lubricants laboratory, and test facilities in the UK, France, and Germany. It is pointed out that there is a need for government and industry to support the facility investment necessary to make progress in aerospace technology. Aspects of international cooperation are also discussed.

Kamchi, J. S.↗
NASA NTRS1992

Memory Network For Distributed Data Processors

Universal Memory Network (UMN) is modular, digital data-communication system enabling computers with differing bus architectures to share 32-bit-wide data between locations up to 3 km apart with less than one millisecond of latency. Makes it possible to design sophisticated real-time and near-real-time data-processing systems without data-transfer "bottlenecks". This enterprise network permits transmission of volume of data equivalent to an encyclopedia each second. Facilities benefiting from Universal Memory Network include telemetry stations, simulation facilities, power-plants, and large laboratories or any facility sharing very large volumes of data. Main hub of UMN is reflection center including smaller hubs called Shared Memory Interfaces.

Bolen, David↗
NASA NTRS2003

A New Simulation Framework for Autonomy in Robotic Missions

Autonomy is a key factor in remote robotic exploration and there is significant activity addressing the application of autonomy to remote robots. It has become increasingly important to have simulation tools available to test the autonomy algorithms. While indus1;rial robotics benefits from a variety of high quality simulation tools, researchers developing autonomous software are still dependent primarily on block-world simulations. The Mission Simulation Facility I(MSF) project addresses this shortcoming with a simulation toolkit that will enable developers of autonomous control systems to test their system s performance against a set of integrated, standardized simulations of NASA mission scenarios. MSF provides a distributed architecture that connects the autonomous system to a set of simulated components replacing the robot hardware and its environment.

Flueckiger, Lorenzo↗
NASA NTRS1985

The NASA Altitude Wind Tunnel (AWT): Its role in advanced icing research and development

Currently experimental aircraft icing research is severely hampered by limitations of ground icing simulation facilities. Existing icing facilities do not have the size, speed, altitude, and icing environment simulation capabilities to allow accurate studies to be made of icing problems occurring for high speed fixed wing aircraft and rotorcraft. Use of the currently dormant NASA Lewis Altitude Wind Tunnel (AWT), as a proposed high speed propulsion and adverse weather facility, would allow many such problems to be studied. The characteristics of the AWT related to adverse weather simulation and in particular to icing simulation are discussed, and potential icing research programs using the AWT are also included.

Blaha, B. J.↗
NASA NTRS1985

The NASA altitude wind tunnel - Its role in advanced icing research and development

Currently experimental aircraft icing research is severly hampered by limitations of ground icing simulation facilities. Existing icing facilities do not have the size, speed, altitude, and icing environment simulation capabilities to allow accurate studies to be made of icing problems occurring for high speed fixed wing aircraft and rotorcraft. Use of the currently dormant NASA Lewis Altitude Wind Tunnel (AWT), as a proposed high speed propulsion and adverse weather facility, would allow many such problems to be studied. The characteristics of the AWT related to adverse weather simulation and in particular to icing simulation are discussed, and potential icing research programs using the AWT are also included.

Blaha, B. J.↗
NASA NTRS1982

A facility for the simulation of low orbit atmospheric oxygen bombardment

A molecular beam facility to simulate the space environment of a spacecraft at low orbit was designed with the intent of studying the effect on the properties of optical elements of oxygen atoms impacting at orbital velocity. The four-stage differentially pumped molecular beam facility includes a variety of oxygen atom beam sources which cover a wide range of velocities (1 km/sec to approximately 8 km/sec), in addition to the ultra-clean experimental environmental of an ultra-high vacuum chamber and an optical diagnostic set-up. The primary oxygen atom beam source used to obtain the 8 km/sec O atoms is an arc heated source. It consists of a modified commercially available plasma torch. The modifications include attachments which provide for a nozzle which is used to expand the atomic beam into the vacuum system, and exhaust channels to dispose of excess torch gas. The torch operates in the 'nontransferred' mode of operation, that is the electric arc is confined within the torch. A plasma is formed in helium by a dc arc. A small amount of O2 is injected downstream from the arc where it is thermally dissociated by the hot He into oxygen atoms. The high temperature and isentropic expansion give the oxygen atoms their velocity. Using seeded beam techniques, oxygen atom beams of approximately 3.5 and approximately 1.5 km/sec, respectively, are obtained.

Arnold, G. S.↗
NASA NTRS1972

Cryogenic applications for environment simulation.

Some of the applications of cryogenics for simulating space environmental conditions are reviewed, and typical existing space simulation facilities are described. The techniques of adapting cryogenics to environmental simulation are discussed. Special attention is given to cryosorption pumps designed to accelerate cryogenic cooling of the adsorbent material.

Hardgrove, W. F.↗
NASA NTRS1986

Laboratory formation of a simulated comet

A laboratory simulation experiment to study the interaction between a cometary plasma and the solar wind has been performed using the UCR-T1 space simulation facility (dia. 1.3 m, length 11 m). Intense plasma flow simulating the solar wind interacts with another light-emitting plasma composed of Ba, Sr, and/or C by a plasma emitter which simulates a cometary coma. The purposes of this experiment are to investigate how the solar wind parameters contribute to the formation of the cometary ion tail and to determine the magnetic field structure of a comet. In order to estimate the solar wind parameters by ground-based observations of actual comets, knowledges of such relationships are essential. The experimental results show that the interplanetary magnetic field of the solar wind is very important in forming the cometary tail.

Minami, S.↗
NASA NTRS1989

Issues in visual support to real-time space system simulation solved in the Systems Engineering Simulator

The Systems Engineering Simulator has addressed the major issues in providing visual data to its real-time man-in-the-loop simulations. Out-the-window views and CCTV views are provided by three scene systems to give the astronauts their real-world views. To expand the window coverage for the Space Station Freedom workstation a rotating optics system is used to provide the widest field of view possible. To provide video signals to as many viewpoints as possible, windows and CCTVs, with a limited amount of hardware, a video distribution system has been developed to time-share the video channels among viewpoints at the selection of the simulation users. These solutions have provided the visual simulation facility for real-time man-in-the-loop simulations for the NASA space program.

Yuen, Vincent K.↗
NASA NTRS1994

International Neutral Buoyancy Simulation of Space Station Hardware

The International Standard Payload Rack (ISPR) Neutral Buoyancy Simulation was conducted at the Marshall Space Flight Center (MSFC) Neutral Buoyancy Simulator facility during April and May 1992. The purpose of this simulation was to evaluate hardware design and operations for the ISPR and U.S. Lab system racks under simulated conditions of microgravity. The ISPR NBS was conducted by an international simulation team including representatives from Boeing, NASA, NASDA, and ESA. Hardware for the ISPR NBS was provided by Boeing, Alenia, ESA, and MSFC. NASDA and its contractors MEH and IHI provided experienced in-tank participants and technical observers who were present for the duration of the simulation. The ISPR NBS was the first Space Station simulation involving NASA, NASDA and ESA. In addition to bringing together technical representatives from around the world, the ISPR NBS included test subjects who are some of the most experienced U.S. and European astronauts. Eight general areas of investigation were addressed during the ISPR NBS, including: utility panel interfaces, rack tilt down, standoff access, wall access behind the rack, rack removal and installation, rack translation, multiple rack operations, and restraints and mobility aids. This paper focuses on aspects of simulation planning, conduct, and reporting that pertain to specifically to the international involvement of the activity.

Lisa C King↗
NASA NTRS2005

TRMM Re-Entry Planning: Attitude Determination and Control During Thruster Modes

The Tropical Rainfall Measuring Mission (TRMM) spacecraft has been undergoing design for a controlled re-entry to Earth. During simulation of the re-entry plan, there was evidence of errors in the attitude determination algorithms during thruster modes. These errors affected the bum efficiency, and thus planning, during re-entry. During thruster modes, the spacecraft attitude is controlled off of integrated Gyro Error Angles that were designed to closely follow the nominal spacecraft pointing frame (Tip Frame). These angles, however, were not exactly mapped to the Tip Frame from the Body Frame. Additionally, in the initial formulation of the thruster mode attitude determination algorithms, several assumptions and approximations were made to conserve processor speed. These errors became noticeable and significant when simulating bums of much longer duration (-10 times) than had been produced in flight. A solution is proposed that uses attitude determination information from a propagated extended Kalman filter that already exists in the TRMM thruster modes. This attitude information is then used to rotate the Gyro Error Angles into the Tip Frame. An error analysis is presented that compares the two formulations. The new algorithm is tested using the TRMM High-Fidelity Simulator and verified with the TRMM Software Testing and Training Facility. Simulation results for both configurations are also presented.

DeWeese, Keith↗
NASA NTRS2011

Assessment of the Draft AIAA S-119 Flight Dynamic Model Exchange Standard

An assessment of a draft AIAA standard for flight dynamics model exchange, ANSI/AIAA S-119-2011, was conducted on behalf of NASA by a team from the NASA Engineering and Safety Center. The assessment included adding the capability of importing standard models into real-time simulation facilities at several NASA Centers as well as into analysis simulation tools. All participants were successful at importing two example models into their respective simulation frameworks by using existing software libraries or by writing new import tools. Deficiencies in the libraries and format documentation were identified and fixed; suggestions for improvements to the standard were provided to the AIAA. An innovative tool to generate C code directly from such a model was developed. Performance of the software libraries compared favorably with compiled code. As a result of this assessment, several NASA Centers can now import standard models directly into their simulations. NASA is considering adopting the now-published S-119 standard as an internal recommended practice.

Jackson, E. Bruce↗
NASA NTRS2014

Simulation Technology at NASA

NASA Ames Research Center is home to several high-fidelity research flight and air-traffic control simulation facilities which, together with an experienced workforce, produce high-quality research data and findings that have proven to be applicable in the real world. These assets include the Vertical Motion Simulator (VMS), Crew Vehicle Systems Research Facility (CVSRF), Future Flight Central (FFC) air traffic control tower simulator, and several air-traffic control (ATC) simulators. The VMS combines a high-fidelity simulation capability with an adaptable simulation environment, enabling customization for numerous human-in-the-loop research applications. The distinctive feature of the VMS is its unparalleled large amplitude, high-fidelity motion capability. In over 30 years of continuous operation, the VMS has contributed significantly to the body of knowledge in a range of disciplines directly benefiting several aerospace programs and flight safety, including the design and development of flight control systems for the Joint Strike Fighter, Space Shuttle Orbiter, and rotorcraft. It continues to be used for researching new vehicle configurations, vehicle control and safety, transfer-of-training, etc., by NASA, other government agencies, and Industry.The CVSRF includes two motion-based flight simulators: a Boeing 747-400 full flight simulator and the reconfigurable Advanced Concepts Flight Simulator (ACFS). These simulators are primarily used to research air-traffic management concepts and procedures, advanced navigation and avionics concepts, and cockpit human factors. FFC is a full-sized control tower simulator with a 360-degree external field-of-view display system and reconfigurable system architecture. FFC and the ATC simulators are used for testing air-traffic management automation and decision support tools and demonstrate their feasibility in a realistic environment prior to technology transfer for implementation in the National Airspace System (NAS).To support integrated simulations and flight-tests for NASA's Unmanned Aircraft Systems (UAS) in the National Airspace System (NAS) Project, NASA developed a distributed test environment incorporating Live, Virtual, Constructive, (LVC) concepts. Development of the software enabling the LVC is conducted primarily at the Distributed Simulation Research Lab (DSRL) at NASA Ames. The LVC components provide the core infrastructure supporting simulation of UAS operations by integrating live and virtual aircraft in a realistic air traffic environment. This provides the ability to conduct tests more efficiently by promoting the use of existing distributed assets. The LVC infrastructure was used in several human-in-the-loop simulations to evaluate acceptance of Detect and Avoid (DAA) advisories used by UAS pilots to maintain well clear of other virtual traffic and to negotiate maneuvers with air traffic control. It is currently being used to support testing of self-separation algorithms between unmanned and manned aircraft in live flight. Further simulations with more comprehensive air traffic scenarios mixing live and virtual aircraft is planned.In the current fiscal environment, maintaining and upgrading these high-fidelity simulation assets and retaining the skilled workforce necessary to meet future research needs is the primary non-technical challenge.

CVSRF↗
NASA NTRS1981

A time lag study of the vertical motion simulator computer system

A study was performed to evaluate an experimental method to determine time lags in real-time computer systems as the one associated with the Vertical Motion Simulator at Ames Research Center. The approach was to use an ordinary frequency analyzer to measure the phase difference between inputs and outputs of the computer system. The various elements of the program and computational architecture were modeled. Various factors, such as computer frame time and input frequency, were varied so that they were representative of the operational use of the simulator facilities. Experimentally determined results were compared with predictions derived from the simulation models. The results indicate that the frequency analyzer can be readily used to evaluate time lags in systems of this type. Differences between predicted and measured phase values indicate that the hardware and software imparts a time lag of about 5 msec to this facility.

Cleveland, W. B.↗
NASA NTRS1972

Calibration of Lewis hypersonic tunnel facility at Mach 5, 6, and 7

Results of the initial calibration tests and a description of this true simulation facility are presented. Facility nozzles were calibrated over a range of stagnation pressure and temperature from 140 to 700 newtons per square centimeter and 1100 to 1750 K. The Reynolds number varied from 1.77 million to 7.44 million per meter. Mach numbers in the inviscid core of the three nozzles were 5.17 plus or minus 0.03, 6.05 plus or minus 0.02, and 7.25 plus or minus 0.08. Usable core diameters at the nozzle exit plane varied from 69 to 86 centimeters. True simulation with these performance capabilities and the test section size presently make this a unique operating facility.

Cullon, R. R.↗
NASA NTRS1973

Space Simulation, 7th

Space simulation facilities and techniques are outlined that encompass thermal scale modeling, computerized simulations, reentry materials, spacecraft contamination, solar simulation, vacuum tests, and heat transfer studies.

Source record↗
NASA NTRS1983

Simulation and evaluation of the Sh-2F helicopter in a shipboard environment using the interchangeable cab system

The operation of the SH-2F helicopter from the decks of small ships in adverse weather was simulated using a large amplitude vertical motion simulator, a wide angle computer generated imagery visual system, and an interchangeable cab (ICAB). The simulation facility, the mathematical programs, and the validation method used to ensure simulation fidelity are described. The results show the simulator to be a useful tool in simulating the ship-landing problem. Characteristics of the ICAB system and ways in which the simulation can be improved are presented.

Paulk, C. H., Jr.↗