Search NASA⌕ Search

SEARCH · Search NASA

Results for “sputtering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

Sputter-deposited CdMgTe for rear contact to CdSeTe/CdTe solar cells

CdTe-based photovoltaic device performance improvement is predominantly limited by open-circuit voltage. This work approaches the voltage deficit challenge through the incorporation of a cadmium magnesium telluride (CdMgTe) electron reflector layer at the back of 1.5- μm CdSeTe/CdTe absorbers to reduce back-surface recombination through a conduction band offset. A sputtered CdMgTe electron reflector layer permitted low fabrication temperatures and circumvented the intolerance of CdMgTe to thermal processing present in traditional close-space sublimation (CSS)-deposited CdMgTe devices. Here, we demonstrate that sputtered CdMgTe simultaneously promotes the retention of chlorine passivation and magnesium which is not feasible with CSS fabrication. We also show the importance of the Cu and Te back contact order in CdMgTe devices. Through the optimization of the sputtered CdMgTe substrate temperature, doping, and back structure configuration, 1.5 μm CdSeTe/CdTe devices with a sputtered CdMgTe layer achieved an efficiency of 16.0%, significantly higher than with CSS CdMgTe, and demonstrated partial enactment of electron-reflector behavior.

14 SOLAR ENERGY↗

Influence of oxygen on the optical and electrical properties of magnetron-sputtered indium tin oxide thin films at ambient temperature

Indium Tin Oxide (ITO) thin films are commonly used as transparent conductive layers in the production of solar cells. ITO films are typically heat-treated at temperatures exceeding 200 °C after magnetron sputtering to optimize the physical, optical, and electrical characteristics for photovoltaic devices. Here, this high temperature heating procedure greatly limits the use of potential substrates, particularly those comprised of low-temperature-rated polymers. Herein, we examine the physical, optical, and electrical transport effects of oxygen:argon plasmas during radio frequency magnetron sputtering of ITO on glass and flexible polymer surfaces without subsequent heat treatment. ITO thin films were characterized via sheet resistance testing, UV-Vis spectroscopy, X-ray diffraction, and scanning electron microscopy imaging. Sheet resistance measurements revealed an increase in surface resistance with increasing oxygen concentration during sputtering. UV-Vis optical transmittance measurements demonstrated an improvement in optical transmittance with an increase in oxygen concentration reaching a maximum transmittance at an oxygen concentration of 1-2 %. Most importantly, it was discovered that producing bilayers of ITO with pure argon sputtered plasmas followed by oxygen:argon plasmas produced ITO thin films with suitable resistance and transmittance without the need for high temperature post annealing. These results highlight a methodology for the deposition of ITO thin films on temperature sensitive substrates for flexible photovoltaics and low-cost module production.

36 MATERIALS SCIENCE↗

Carbon Electrode with Sputtered Au Coating for Efficient and Stable Perovskite Solar Cells

Halide perovskite solar cells (PSCs) represent a low-cost and high-efficiency solar technology. However, most of the highly efficient PSCs need a noble electrode, such as Au, through thermal evaporation. Here it is reported that a sputtered Au electrode on a PSC could damage the organic hole transport layer (HTL) and the perovskite layer. Here, we report a simple, yet effective sputtered gold nanoparticle decorated carbon electrode to fabricate efficient and stable planar PSCs. The sputtered Au layer on the doctor-bladed coated carbon electrode can be directly applied to the perovskite semicells by mechanical stacking. By optimizing the gold thickness, a power conversion efficiency (PCE) of 16.87% was obtained for the composite electrode-based PSC, while the reference device recorded a PCE of 12.38%. The composite electrode-based device demonstrated 96% performance retention after being stored under humid conditions (50-60%) without encapsulation for ~100 h. This demonstrates a promising pathway toward the commercialization of large-scale manufacturable sputtered electrodes for the PSC solar module.

14 SOLAR ENERGY↗

Combinatorial Nitrogen Gradients in Sputtered Thin Films

High-throughput synthesis and characterization methods can significantly accelerate the rate of experimental research. For physical vapor deposition (PVD), these methods include combinatorial sputtering with intentional gradients of metal/metalloid composition, temperature, and thickness across the substrate. However, many other synthesis parameters still remain out of reach for combinatorial methods. Here, we extend combinatorial sputtering parameters to include gradients of gaseous elements in thin films. Specifically, a nitrogen gradient was generated in a thin film sample library by placing two MnTe sputtering sources with different gas flows (Ar and Ar/N 2 ) opposite of one another during the synthesis. The nitrogen content gradient was measured along the sample surface, correlating with the distance from the nitrogen source. The phase, composition, and optoelectronic properties of the resulting thin films change as a function of the nitrogen content. Furthermore, this work shows that gradients of gaseous elements can be generated in thin films synthesized by sputtering, expanding the boundaries of combinatorial science.

14 SOLAR ENERGY↗

Co-sputtering of lithium vanadium oxide thin films with variable lithium content to enable advanced solid-state batteries

Advanced solid-state batteries most likely will entail aggressive structures or architectures with constraints that typically limit processing temperatures. Considering this, we have identified the importance of providing lithiated electrode materials at a modest processing temperature. Here we describe a pathway to meet this by the development of a co-sputtering process using lithium oxide and vanadium oxide targets which enables the growth of lithiated vanadium oxide (LVO) thin films for application in solid-state batteries. Analysis of the structure and film composition of samples deposited with different co-sputtering rate ratios and post-annealing shows that multiple phases of Li x V 2 O 5 likely coexist (i.e. α-, ε-, δ-, and γ-V 2 O 5 ), and that this is unchanged after electrochemical cycling. The co-sputtering process can tune the lithium content up to a highly lithiated state of at least Li 2 V 2 O 5 . Electrochemical half-cells showed a significant amount of lithium available on the first charge (delithiation of LVO). LVO samples post-annealed at 300 °C showed typical redox peaks for Li x V 2 O 5 for both one and two lithium insertion reactions, which were highly reversible in most cases. A thin-film solid-state battery prototype using LVO as a cathode had 20% of the expected capacity, although the coulombic efficiency is near 100% at a fast rate (22C). As a result, this co-sputtering technique represents an opportunity for low temperature synthesis of pre-lithiated cathodes for thin film batteries, and introduces a broader methodology of depositing metal oxides with different alkali metal contents.

25 ENERGY STORAGE↗

Optical spectroscopic study of the SiN/HfO{sub 2} interfacial formation during rf sputtering of HfO{sub 2}

High-k stacks formed by chemical-vapor-deposited SiN and high-pressure sputtered HfO{sub 2} in either O{sub 2} or Ar atmosphere have been studied. The introduction of a SiN layer is proposed to prevent the uncontrollable SiO{sub 2} growth while sputtering. The formation of Si-O bonds after the sputtering of the HfO{sub 2} film in O{sub 2} atmosphere was observed by infrared spectroscopy. Optical diagnosis of the plasma demonstrated a high density of O radicals in the system when working with O{sub 2}. The small radius and high reactivity of these O radicals are the source of the SiN oxidation. However, the structure of the SiN film is preserved during Ar sputtering.

36 MATERIALS SCIENCE↗

Gasless sputtering: Opportunities for ultraclean metallization, coatings in space, and propulsion

Pulsed magnetron sputtering was demonstrated in high vacuum: no sputter gas was used at any time. Sustained self-sputtering was initiated by multiply charged ions from a short vacuum arc. Copper ion currents to an ion collector in excess of 30 A were measured, implying a plasma density of about 6x10{sup 18} m{sup -3}. This technology may prove useful for metal coatings free of noble gas inclusions and suggests that magnetrons could operate in the vacuum of space. In addition to coating objects in space, the momentum of the sputtered atoms and ions may be utilized in space thrusters.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Experiment and simulation of the compositional evolution of Ti-B thin films deposited by sputtering of a compound target

The evolution of the coating stoichiometry with pressure, target-substrate distance, and angle was analyzed for dc sputtering of Ti{sub x}B (x=0.5, 1, 1.6) compound targets by elastic recoil detection analysis. For an investigation of the underlying fundamental processes primarily Ar was used as sputter gas. Additionally, the effect of a reactive gas (N{sub 2}) as well as bias voltage (floating up to -200 V) was briefly cross-checked. For deposition along the target normal (90 deg.) a pronounced Ti-deficiency of up to 20% is detected. Increasing the pressure or distance from 0.5 to 2 Pa and from 5 to 20 cm, respectively, leads to an almost equivalent linear increase in Ti/B ratio surpassing even the target composition. Off-axis depositions at lower angles (30 deg. and 60 deg.) on the other hand result in a higher Ti/B ratio. This is consistent with results obtained from Monte Carlo simulations combining the respective emission characteristics from the sputter process as well as the gas-phase transport. Hence, the pressure, distance, and sample position induced changes in chemical film composition can be understood by considering gas scattering and the angular distribution of the sputtered flux. The theoretically determined transition from a directional flux to thermal diffusion was experimentally verified by mass-energy analysis of the film-forming atoms.

36 MATERIALS SCIENCE↗

Quantification of self-sputtering and implantation during pulsed laser deposition of gold

This work reports on the quantification of self-sputtering and implantation occurring during pulsed laser deposition of Au as a function of the laser fluence used to ablate the gold target. The experimental approach includes, on one hand, in situ electrical (Langmuir) and optical (two-dimensional imaging) probes for determining, respectively, ion and excited neutral kinetic energy distributions. On the other hand, it includes determination of the density of (i) ions reaching a substrate, and (ii) gold atoms deposited on a substrate as well as of a proportion of atoms that are self-sputtered. The experimental results supported by numerical analysis show that self-sputtering and implantation are both dominated by ions having kinetic energies {>=}200 eV. They are a fraction 0.60-0.75 of the species arriving to the substrate for ablation laser fluences 2.7-9.0 J cm{sup -2}. Self-sputtering yields in the range 0.60-0.86 are determined for the same fluence range.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Correlation between sputtering parameters and composition of SmCo-based films for microelectromechanical system applications

About 3.0 {mu}m thick SmCo-based films with additives of Fe, Cu, and Zr were deposited on Si substrates. Based on a developed semiempirical theoretical model, the dependence of the film composition on the sputtering parameters was discussed. The experimental results show that the Sm concentration increases with decreasing sputtering power or increasing Ar gas pressure, which are in good agreement with the calculated results when the preferential sputtering effect is disregarded. The effect of the sputtering parameters on the film composition provides an opportunity for the same composite target to fabricate films with Sm concentration varying from 13.8 to 17.3 at. %, which is reasonable for the permanent magnetic phase transformation (Sm{sub 2}Co{sub 17}{yields}SmCo{sub 7}{yields}SmCo{sub 5}). Furthermore, the observed TbCu{sub 7}-type film shows a better crystal texture with a low remanence ratio for the hysteresis loops measured out plane to in plane of 0.08.

36 MATERIALS SCIENCE↗

Evolution of the plasma composition of a high power impulse magnetron sputtering system studied with a time-of-flight spectrometer

The plasma of a high power impulse magnetron sputtering system has been investigated using a time-of-flight spectrometer. The target materials included high sputter yield materials (Cu, Ag), transition metals (Nb, Cr, Ti), and carbon (graphite); the sputtering gases were argon, krypton, and nitrogen, and two different target thicknesses were selected to consider the role of the magnetic field strength. Measurements for selected combinations of those parameters give quantitative information on the transition from gas-dominated to metal-dominated (self-sputtering) plasma, on the fractions of ion charge states, and in the case of molecular gases, on the fraction of atomic and molecular ions.

36 MATERIALS SCIENCE↗

Quartz crystal microbalance-based system for high-sensitivity differential sputter yield measurements

We present a quartz crystal microbalance-based system for high sensitivity differential sputter yield measurements of different target materials due to ion bombardment. The differential sputter yields can be integrated to find total yields. Possible ion beam conditions include ion energies in the range of 30-350 eV and incidence angles of 0 deg. - 70 deg. from normal. A four-grid ion optics system is used to achieve a collimated ion beam at low energy (<100 eV) and a two-grid ion optics is used for higher energies (up to 750 eV). A complementary weight loss approach is also used to measure total sputter yields. Validation experiments are presented that confirm high sensitivity and accuracy of sputter yield measurements.

36 MATERIALS SCIENCE↗

Gallium ion extraction from a plasma sputter-type ion source

A broad mixed ion beam containing positive ions of gallium (Ga) was produced with a plasma sputter-type ion source. Liquid Ga was suspended on a tungsten reservoir to be sputtered and postionized in argon (Ar) plasma excited by a radio frequency (rf) power at 13.56 MHz. Optical emission spectra from the plasma near the Ga sputtering target had indicated that the release of Ga into plasma increased with increasing negative bias to the sputtering target. The ratio of Ga{sup +} current to Ar{sup +} current was measured to be about 1% with a quadrupole mass analyzer at 100 V extraction voltage for incident rf power as low as 30 W. Ions in the plasma were extracted through a pair of multiaperture electrodes. The homogeneity of Ga flux was examined by making a Ga deposition pattern on a glass substrate located behind the extractor electrodes.

43 PARTICLE ACCELERATORS↗

Optical characterization of a-As{sub 2}S{sub 3} thin films prepared by magnetron sputtering

It is well known that thermally evaporated a-As{sub 2}S{sub 3} thin films are prone to oxidation when exposed to ambient environment. These As{sub 2}O{sub 3} crystals can have a devastating effect on propagating light by introducing a major source of scattering loss in submicron optically integrated circuits. Magnetron sputtering a-As{sub 2}S{sub 3} not only produces films that have optical properties closer to their equilibrium state like their bulk glass counter parts, the as-deposited films also show no detectable signs of As{sub 2}O{sub 3} crystals in them when they are exposed to the ambient environment. These attributes are unique to a magnetron sputtered a-As{sub 2}S{sub 3} film and are probably caused by the ''photoannealing'' effect from the visible light emitted by the argon plasma during the sputtering process. The optical properties of a magnetron sputtered a-As{sub 2}S{sub 3} film and its propagation loss on a Ti diffused LiNbO{sub 3} waveguide are reported here. The thin film results agree closely with published data on As{sub 2}S{sub 3} bulk glass, and the optical properties of the as-deposited film are found to be closer to its bulk glass values than films made by thermal evaporation and pulsed laser deposition. The TM propagation loss at {lambda}=1.5 {mu}m of the as-deposited a-As{sub 2}S{sub 3} waveguide on Ti:LiNbO{sub 3} was 0.20{+-}0.05 dB/cm.

36 MATERIALS SCIENCE↗

Fabrication of size-selected Pd nanoclusters using a magnetron plasma sputtering source

We report on the fabrication of palladium (Pd) nanoclusters using a dc magnetron sputtering source. Plasma sputtering vaporizes the target's material forming nanoclusters by inert gas condensation. The sputtering source produces ionized nanoclusters that enable the study of the nanoclusters' size distribution using a quadrupole mass filter. In this work, the dependence of Pd nanoclusters' size distribution on various source parameters, such as the sputtering discharge power, inert gas flow rate, and aggregation length have been investigated. This work demonstrates the ability of tuning the palladium nanoclusters' size by proper optimization of the source operation conditions. The experimental nanocluster sizes are compared with a theoretical model that reveals the growth of large nanoclusters from 'embryos' by a two-body collision. The model is valid for a specific range of deposition parameters (low inert gas flow rates and aggregation lengths equal or below 70 mm).

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Ion-enhanced oxidation of aluminum as a fundamental surface process during target poisoning in reactive magnetron sputtering

Plasma deposition of aluminum oxide by reactive magnetron sputtering (RMS) using an aluminum target and argon and oxygen as working gases is an important technological process. The undesired oxidation of the target itself, however, causes the so-called target poisoning, which leads to strong hysteresis effects during RMS operation. The oxidation occurs by chemisorption of oxygen atoms and molecules with a simultaneous ion bombardment being present. This heterogenous surface reaction is studied in a quantified particle beam experiment employing beams of oxygen molecules and argon ions impinging onto an aluminum-coated quartz microbalance. The oxidation and/or sputtering rates are measured with this microbalance and the resulting oxide layers are analyzed by x-ray photoelectron spectroscopy. The sticking coefficient of oxygen molecules is determined to 0.015 in the zero coverage limit. The sputtering yields of pure aluminum by argon ions are determined to 0.4, 0.62, and 0.8 at 200, 300, and 400 eV. The variation in the effective sticking coefficient and sputtering yield during the combined impact of argon ions and oxygen molecules is modeled with a set of rate equations. A good agreement is achieved if one postulates an ion-induced surface activation process, which facilitates oxygen chemisorption. This process may be identified with knock-on implantation of surface-bonded oxygen, with an electric-field-driven in-diffusion of oxygen or with an ion-enhanced surface activation process. Based on these fundamental processes, a robust set of balance equations is proposed to describe target poisoning effects in RMS.

36 MATERIALS SCIENCE↗

On the phase formation of sputtered hafnium oxide and oxynitride films

Hafnium oxynitride films are deposited from a Hf target employing direct current magnetron sputtering in an Ar-O{sub 2}-N{sub 2} atmosphere. It is shown that the presence of N{sub 2} allows for the stabilization of the transition zone between the metallic and the compound sputtering mode enabling deposition of films at well defined conditions of target coverage by varying the O{sub 2} partial pressure. Plasma analysis reveals that this experimental strategy facilitates control over the flux of the O{sup -} ions which are generated on the oxidized target surface and accelerated by the negative target potential toward the growing film. An arrangement that enables film growth without O{sup -} ion bombardment is also implemented. Moreover, stabilization of the transition sputtering zone and control of the O{sup -} ion flux without N{sub 2} addition is achieved employing high power pulsed magnetron sputtering. Structural characterization of the deposited films unambiguously proves that the phase formation of hafnium oxide and hafnium oxynitride films with the crystal structure of HfO{sub 2} is independent from the O{sup -} bombardment conditions. Experimental and theoretical data indicate that the presence of vacancies and/or the substitution of O by N atoms in the nonmetal sublattice favor the formation of the cubic and/or the tetragonal HfO{sub 2} crystal structure at the expense of the monoclinic HfO{sub 2} one.

36 MATERIALS SCIENCE↗

Energy effects on the sputtering yield of Si bombarded with gas cluster ion beams

Gas cluster ion presents various irradiation effects such as high sputtering yields. It is important to study the optimum condition of incident cluster ion beam for applications in surface modification technology. In this study, the effects of incident energy and chamber pressure on the sputtering yield with gas cluster ion bombardment were investigated. The incident mean cluster size was 2000 atoms/ion and incident energy was 10-80 keV. The number of collisions with residual gas during transportation was in the range 1-20. The sputtering yield with gas cluster ion beam increased nonlinearly with increasing incident cluster energy. However, cluster ion beam easily lose their energy by collision with residual gas, and the sputtering yield decreased rapidly. For using gas cluster ion beam efficiently, the collision frequency along transportation should be kept less than a few times.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗