Search NASA⌕ Search

SEARCH · Search NASA

Results for “techno economics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Techno-Economic Analysis for a Potential Geothermal District Heating System in Tuttle, Oklahoma: Preprint

Geothermal deep direct use (DDU) has potential across a wide swath of the United States but is underutilized due to challenging project economics associated with developing a deep geothermal resource for a large-scale and variable heat demand. The National Renewable Energy Laboratory (NREL) and University of Oklahoma evaluated the feasibility of a geothermal district heating (GDH) and cooling system in two schools and 250 houses by utilizing existing oil and gas (O&G) wells in Tuttle, Oklahoma. Heating and cooling demand in the two schools and a typical single-family house were modeled using EnergyPlus building energy simulation software. The modeling results indicated that annual heating demand in two schools and 250 houses is approximately 2.61 GWhth, and cooling demand in the two schools is approximately 2.65 GWhth. In this scope, the techno-economic analysis (TEA) was conducted using the GEOPHIRES tool combined with the TOUGH2 reservoir simulator. The reservoir performance, including geothermal heat production capacity, was modeled by the reservoir simulator TOUGH2. Then, levelized cost of heat (LCOH) was calculated using GEOPHIRES version 3.0, which includes new features such as hourly heat load optimization and peak performance evaluation. Geothermal reservoir temperature was estimated as 90.5 degrees C at a total depth of 3.3 km by the regional average temperature gradient of 22.8 degrees C/km and validated by cation geothermometer calculations. Four production scenarios with two different well configurations and two different heat load profiles have been developed for well flow rates ranging between 3.1 kg/s and 9.3 kg/s. The LCOH of the district heating and cooling system was calculated between $95 and $210/MWh ($28/MMBtu to $62/MMBtu) for four different production scenarios. Typical natural gas prices for residential customers in Oklahoma have ranged from 9 to 19 $/MMBtu over the past decade, which indicates a challenge for deployment of such a GDH system.

deep direct-use↗
DOE OSTI2025

Preliminary Techno-Economic Assessment of Gas Switching Reforming (GSR) of Natural Gas for Pure Hydrogen Production and Power Generation with Integrated CO2 Capture

The increasing demand for hydrogen and the CO2 intensity of natural gas (NG) reforming motivate the development of low-carbon-emission hydrogen production technologies. Gas Switching Reforming (GSR) is an advanced auto-thermal reforming technology that produces hydrogen or syngas from natural gas. It integrates inherent CO2 capture by utilizing a specialized oxygen carrier in a single fluidized bed reactor, eliminating the need for complex, energy-intensive post-combustion separation. GSR technology builds upon Chemical Looping Reforming (CLR), an experimentally proven technology with strong potential for scaling up. In this study, select oxygen carriers (OC) (NiO/Al2O3, Fe2O3-CeO2/Al2O3, and magnetite) were tested in methane steam reforming in a fixed bed reactor to determine their relative reactivities under relevant conditions for GSR (800 °C, 7 bar total pressure). Process models were then developed to perform techno-economic analysis (TEA) of GSR for hydrogen production (GSR-H₂) and a combined cycle (GSR-CC) in which high-purity H₂ is fired in a gas turbine to produce electricity. Operating at 10 bar and 1100 °C and with the additional recovery steps implemented increased H₂ production by ~30% and improved efficiency relative to prior studies. For GSR-H₂, the levelized cost of hydrogen (LCOH) is 1.61–1.64 $/kg-H₂, competitive with a reference SMR case, though operating and maintenance costs are higher due to increased electricity demand. GSR-CC has a significantly higher levelized cost of electricity (LCOE) than its reference NGCC (natural gas combined cycle) plant, suggesting it is less competitive; however, increasing production scale could make it more attractive. Life-cycle results for GSR-H2 indicate NG consumption drives ~75% of total global warming impacts (~2.3 kg CO2 eq/kg H2). An environmental, health, and safety screening suggests iron-based carriers are comparatively safer, whereas NiO may pose greater risks. Overall, GSR-H2 is a scalable, competitive option for hydrogen production using nickel and non-nickel OC.

03 NATURAL GAS↗
DOE OSTI2025

Techno-economic assessment of distributed wellhead RO water treatment for nitrate removal and salinity reduction: A field study in small disadvantaged communities

Techno-economic analysis of distributed wellhead water treatment and desalination (DWTD) systems was carried out based on a three-year field study in three small, disadvantaged communities (DACs) to evaluate the reliability and affordability of upgrading their impaired well water. The local water supplies of the three study DACs, located in Salinas Valley, California, were contaminated with nitrate at levels (~ 12–87 mg/L NO$^{-}_{3}$ - N) ) above the California maximum contaminant level (MCL) of 10 mg/L NO$^{-}_{3}$ - N , and had elevated water salinity (~600–1,600 mg/L total dissolved solids(TDS)) above its secondary MCL (SMCL) of 500 mg/L TDS. Well water nitrate removal and salinity reduction were accomplished via reverse osmosis (RO) based DWTD systems that operated autonomously, supported by remote monitoring and supervisory cyberinfrastructure. Reliable DWTD operation provided treated water quality, with respect to nitrate and salinity, in the range of 0.5–6.3 mg/L NO$^{-}_{3}$ - N and 57–161 mg/L TDS, respectively, which were well below the respective MCL and SMCL. The levelized cost of water treatment was in the range of ~$$2/m 3 - $$2.9/m 3 which aligns with typical residential water costs in California and in the study region, and monthly residential water costs (39 dollars-74 dollars/residential unit/month) were also within the range in California. The study showcased the DWTD approach as a viable and potentially scalable solution for upgrading impaired local potable water supply of communities lacking centralized water delivery infrastructure. However, streamlined permitting processes and standardized regulatory frameworks are critical to promoting wider adoption and maximizing the socio-economic benefits of the DWT approach. Moreover, DACs are likely to require government subsidies in order to cover the CapEx of DWTD systems in addition to upgrade of site infrastructure.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2026

A Kinetic Model-Driven Techno-Economic Analysis of Plastic Pyrolysis: Linking Process Dynamics to Economic Viability

This study employs a kinetic model integrated into Aspen Plus to predict pyrolysis product distribution under various conditions. A techno-economic assessment calculated the minimum selling price (MSP) of pyrolysis oil under different operating conditions for the baseline capacity of 100 kta, and across eight processing capacities ranging from 30 to 150 kta. The lowest MSP under the baseline capacity is estimated at $\$$420/ton, which is 33% lower than the 2023 average US crude oil price ($\$$74.6/bbl, equivalent to $\$$634/ton based on the density of pyrolysis oil). Under Monte Carlo simulation, accounting for variability in key economic and technical parameters, the mean MSP is estimated at $\$$1137/ton. The economic viability depends on feedstock price remaining below $\$$320/ton, defining the break-even feedstock price threshold. Sensitivity analysis further identifies capital investment and transportation cost as key economic drivers. Capacities beyond 90 kta show limited economies of scale benefits. Reducing product storage time cuts capital costs by 7% but raises operational risk. Uncertainty analysis suggests the economic feasibility of pyrolysis oil is unlikely to compete with crude oil without policy incentives.

petrochemicals↗
DOE OSTI2020

Techno-Economic Analysis of Synthetic Fuels Pathways Integrated with Light Water Reactors

The purpose of this work is to identify, model, perform techno-economic analysis, and compare two possible synfuel production routes utilizing CO 2 as the feedstock. Heat from an LWR nuclear plant is integrated wherever possible to positively affect the economics of the LWR by converting power to fuels during times of low grid electricity demand. Process and economic modeling for a conceptual synfuel production plant co-located (or in near proximity) with an LWR is presented, including the cost of CO 2 captured from an ethanol plant, compressed, and transported to the LWR hybrid plant, co-electrolysis of the CO 2 with water in a solid oxide electrolyzing cell (SOEC) system to produce syngas, and thermocatalytic conversion of the syngas to transportation fuel. The hybrid LWR/synfuels plant is assumed to be located within 50–150 miles of an ethanol plant (e.g., located in the midwest region of the United States). Performance and nth-plant economics for the co-electrolysis-based processes are evaluated and compared with biomass-gasification-based technology for the synfuel routes considered. Sensitivity analysis around the price of CO 2 and electricity, two of the major cost drivers, is presented for each case. Consideration of a carbon credit is also included in the sensitivity analysis.

10 SYNTHETIC FUELS↗
DOE OSTI2023

Techno-Economic Models are Instrumental in Analyzing Decarbonization Strategies

This presentations provides a high-level overview of the NETL-developed techno-economic models associated with the CO2 transport and CO2 storage components of the carbon capture and storage (CCS)/carbon capture, utilization, and storage (CCUS) value chain. It also discusses the models’ capabilities through the discussion of select modeling applications (both internal and external) and highlights current model modifications and future work. It was presented at the CCUS 2023 conference, organized and presented by the Society of Petroleum Engineers (SPE), American Association of Petroleum Geologists (AAPG), and Society of Exploration Geophysicists (SEG) and held in Houston, Texas, April 25-27, 2023.

Guinan, Allison↗
DOE OSTI2022

Rewiring yeast metabolism for producing 2,3-butanediol and two downstream applications: Techno-economic analysis and life cycle assessment of methyl ethyl ketone (MEK) and agricultural biostimulant production

Rising concerns for sustainability and global climate change have driven the development of sustainable pro- duction pathways for biofuels and chemicals from lignocellulosic biomass via integrated biological and chemical processes. We constructed an engineered Saccharomyces cerevisiae capable of producing 2,3-butanediol (2,3-BDO) from glucose without accumulating ethanol and glycerol, which hinder downstream processing of 2,3-BDO, through extensive metabolic reprogramming. Specifically, we introduced heterologous 2,3-BDO biosynthetic enzymes and deleted the major isozymes of ethanol and glycerol biosynthetic enzymes. In addition, we introduced an NAD + regenerating Pyruvate-Malate (PM) cycle and enhanced the NAD + regenerating capability of the PM cycle to resolve the redox imbalance from the deletion of ethanol and glycerol production pathways. The resulting engineered yeast produced 109.9 g/L of 2,3-BDO with a productivity of 1.0 g/L/h and a yield of 0.36 g/ g glucose in a fed-batch fermentation. We also conducted techno-economic analysis (TEA) and life cycle assessment (LCA) of the production of methyl ethyl ketone (MEK) through catalytic dehydration of 2,3-BDO. A TEA based on the experimental results indicated that the minimum product selling price (MPSP) was estimated to be $1.90/kg. Regarding cradle-to-grave LCA, 100-year global warming potential (GWP100) and fossil energy consumption (FEC) were found to be 0.37 kg CO 2 eq/kg and 3.1 MJ/kg, respectively. These results demonstrated the feasibility of cost-competitive and sustainable bio-based MEK production via yeast fermentation. In addition, we explored the possibility of using the fermentation broth containing 2,3-BDO as a biostimulant inducing drought tolerance in plants. As a result, the yeast 2,3-BDO fermentation broth can induce drought tolerance in Arabidopsis thaliana without a complicated purification process.

2,3-butanediol (2,3-BDO)↗
DOE OSTI2023

Process Design and Techno-Economic Analysis of the Modular Staged Pressurized Oxy-Combustion (SPOC) Power Plant for Biomass

This work describes the process design and techno-economic analysis (TEA) of the modular stage pressurized oxy-combustion (SPOC) power plant for biomass firing and coal-biomass co-firing. The SPOC process was modelled using Aspen Plus®, and largely based on a previous model designed by this group for SPOC coal firing. To enable comparison with current National Energy Technology Laboratory (NETL) Bio-Energy Carbon Capture and Storage (BECCS) studies, a 550 MWe SPOC power plant with a supercritical Rankine cycle (241 bar, 593°C, and 593°C), and 90% carbon capture was modeled, and hybrid poplar biomass was chosen. Two cases were evaluated, namely 100% biomass (carbon negative) and 25% biomass co-firing (carbon neutral), and the 100% Powder River Basin coal firing case was chosen for comparison purposes. In the SPOC process, oxygen is produced via a cryogenic air separation unit (ASU) and the heat generated from the compression of air is integrated into the steam cycle and utilized for boiler feed water regeneration. Unique to the SPOC process, the boilers are arranged in a series-parallel configuration, with minimized flue gas recirculation. The flue gas is cooled and scrubbed in the direct-contact cooler (DCC) column, and the water leaving the bottom of the DCC is at a sufficiently high temperature that it can be used for boiler feed water heating, improving plant thermal efficiency. The SPOC efficiencies were above the BECCS cases with capture, and no efficiency penalty on the SPOC plant was observed with an increase of biomass in the mix mostly due to the higher oxygen content in biomass that resulted in lower oxygen requirement from the ASU, and the higher moisture in biomass that due to the key benefit of the SPOC process can be partially recovered as latent heat.

Magalhaes, Duarte↗
DOE OSTI2024

Process Design and Techno-Economic Analysis of the Modular Staged Pressurized Oxy-Combustion (SPOC) Power Plant for Biomass

This work describes the process design and techno-economic analysis (TEA) of the modular SPOC power plant for biomass firing and coal-biomass co-firing. Two Rankine cycles were considered: a supercritical steam cycle (242 bar, 593°C, 593°C) with 550 MWe net output and a subcritical cycle (166 bar, 566°C, 566°C) with 200 MWe net output. For both cases, 95% carbon capture was modeled, and hybrid poplar biomass was chosen to generate carbon-negative power. In addition, the supercritical 500 MWe case included a 25% biomass co-firing (carbon neutral) case. For both cycles, a 100% Powder River Basin coal firing case was used for comparison purposes. In the SPOC process, oxygen is produced via a cryogenic air separation unit (ASU) and the heat generated from the compression of air is integrated into the steam cycle and utilized for boiler feed water pre-heating. Unique to the SPOC process, the boilers are pressurized and arranged in a series-parallel configuration, with minimized flue gas recirculation. The flue gas is cooled and scrubbed in the direct-contact cooler (DCC) column, and the moisture in the flue gas is condensed, leaving the bottom of the DCC at a sufficiently high temperature such that it can be used for boiler feed water pre-heating, improving plant thermal efficiency. Following drying and purification, CO2 in the flue gas is at the purity required for storage or utilization. The performance data were obtained from process modelling via Aspen Plus®. The stream data from Aspen Plus® were used as an input for the AACE Class 5 cost study. Ultimately, the capital costs, Levelized Cost of Electricity (LCOE), and cost of CO2 captured and avoided were obtained. The HHV efficiency of the carbon negative 550 MWe supercritical SPOC case (34.8%) was clearly above those reported by NETL for the BECCS baseline cases of supercritical pulverized coal with capture (B12B, 31.5%) and the 49% biomass co-firing case with capture (PA3, 29.2%). The HHV efficiency of the carbon-negative subcritical plant is also higher than the subcritical baseline PC plant with capture (case B11B.95) presented by NETL (32% vs 29.7%). The LCOE for the SPOC 100% biomass case was similar to the LCOE for the BECCS 49% biomass with carbon capture case ($147/MWh), and the SPOC carbon neutral case LCOE was lower ($110/MWh) than the cost for the NETL baseline SC coal firing case with 90% carbon capture ($114/MWh).

Magalhaes, Duarte↗
DOE OSTI2025

Socio-Techno-Economic Feasibility of Deep Geothermal with EGS for Residential District Heating in the Northeastern United States

In this paper, we present socio-techno-economic simulation results for enhanced geothermal system (EGS) district heating systems in the northeastern United States. We applied the geospatial Distributed Geothermal Market Demand (dGeo) tool coupled with GEOPHIRES to evaluate the feasibility of geothermal deep direct-use, utilizing EGS reservoirs for providing residential heating with district heating systems. The results were combined with JEDI results to assess social impacts. Simulation results assuming doublet EGS reservoirs with target production temperature of 80 degrees C and newly constructed district heating systems indicate a wide range in system levelized cost of heat (LCOH) values ranging from ~$15/MMBtu to over $1,000/MMBtu, with most the attractive regions urban areas with high total thermal demand and high thermal demand density. We estimate about 60 GWth in potential installed capacity with LCOH values under $50/MMBtu and 100 GWth in potential capacity with LCOH values under $100/MMBtu, respectively.

15 GEOTHERMAL ENERGY↗
DOE OSTI2021

Techno-economic-environmental impacts of industrial energy assessment: Sustainable industrial motor systems of small and medium-sized enterprises

Energy assessments can provide an effective way of identifying and implementing energy efficiency measures to save energy costs and avoid emissions throughout manufacturing facilities. Consequently, it generates significant economic and environmental benefits to localities, states, and the nation. Quantifying these benefits requires a systematic techno-economic-environmental framework for capturing the interactions. This article employs methodologies to improve the energy efficiency of small and medium-size industries through their sustainable industrial motor systems. Motor systems offer large opportunities to enhance energy efficiency through adopting advanced technologies and better-informed operations. Case studies presented illuminate the potential savings and impacts from implementing sustainable motor systems and the importance of energy assessments. Here, the integrated macro-economic analysis quantifies the regional sustainability impacts of implementing the industrial energy efficiency offered by an energy auditing program in Ohio over a ten-year period. Results show that implementing all the center’s motor recommendations have directly saved $\$702$ M in energy costs, avoided 2.7 million metric tons of carbon dioxide emissions, and created 3,445 jobs, resulting in a total annual economic impact of $\$788$ M stemming from direct, indirect, and induced regional economic impacts. It provides policy implications for encouraging sustainable industrial motor systems.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2023

A Comparison of Multiple Macroalgae Cultivation Systems and End-Use Strategies of Saccharina latissima and Gracilaria tikvahiae Based on Techno-Economic Analysis and Life Cycle Assessment

Macroalgae can be processed into various products with the potential to substitute land-based crops; their cultivation can bioextract nutrients from coastal waters. This study investigated the economic cost and environmental impacts of multiple seaweed cultivation platforms, cultivation strategies, and processing/end-use strategies through techno-economic analysis (TEA) and life cycle assessment (LCA) with a focus on Saccharina latissima and Gracilaria tikvahiae. Cultivation platforms included single-layer longline, dual-layer longline, single-layer strip, and dual-layer strip systems. Processing/end-use products included seaweed to biofuel, dried sea vegetables, marketable commercial fertilizer, and animal feed. Economic and environmental costs decreased with dual-layer and strip cultivation systems. Cultivation costs were highest using the common single-layer longline system ($4.44 kg−1 dry weight (dw) S. latissima and $6.73 kg−1 dw G. tikvahiae when cultivated on rotation). The use of the dual-layer strip system reduced cultivation costs to $2.19 kg−1 dw for S. latissima and $3.43 kg−1 dw for G. tikvahiae. Seaweed drying was the major contributor to economic and environmental costs for macroalgae processing. Yet, all scenarios achieved environmental benefits for marine eutrophication. The best environmental performance was observed when biomass was processed to dry sea vegetables, assuming the offset of land-based vegetable production, or used as biofeedstock for anaerobic digestion for combined heat and power.

Wu, Jingjing (ORCID:0000000305311353)↗
DOE OSTI2020

A Techno-economic Analysis for Integrating an Electrochemical Reactor into a Lignocellulosic Biorefinery for Production of Industrial Chemicals and Hydrogen

In this study, we present a techno-economic analysis for integrating an electrochemical reactor into a lignocellulosic biorefinery for the purpose of converting biorefinery lignin to higher-value industrial chemicals with co-generation of hydrogen. We consider how the electrochemical reactor impacts the manufacturing costs for producing biofuel and determine a break-even value for the lignin oxidation product stream, which is the minimum lignin conversion product stream value that renders the cost to produce biofuel the same as in the typical biorefinery concept. We conclude that at low extents of lignin conversion, the break-even product stream value is likely too high for the process to be feasible. However, at higher extents of lignin conversion, the break-even product stream value may be between 1.00 and 2.00/kg, depending on capital cost and other manufacturing costs like depreciation. Here the potential markets for the biomass conversion products include resin manufacturing, where the products would compete with petroleum-derived resin precursors.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Enabling a Flexible Grid with Increased Penetration of DER: Techno-economic Analysis of Metal Hydride Thermochemical Energy Storage Integrated with Stirling Engine for Grid Energy Storage Applications

This report summarizes the results of a techno-economic assessment of the capital and operational expenses for 3 scenarios utilizing a TES/Stirling engine system which is charged by an electric heater to provide grid power and energy storage. While there are several integration possibilities and material choices that could be utilized in such systems, three difference scenarios were chosen for this assessment to reflect an anticipated deployment of the technology where each might require different TES system configurations. Additionally, an enhanced version of the HTMH is considered to demonstrate the expected impact on costs with further technology development. The predicted capital and operational LCOS for the system configurations range from $0.0198/kWhr e - $0.0734/kWhr e which compare positively to the LCOS for lithium ion battery storage ranging from $0.087/kWhr e – $0.329/kWhr e . The key drivers for cost improvements to the system are material property enhancements in the HTMH primarily related to reducing the costs associated with the HTMH vessel and heat exchangers. This analysis demonstrates the potential benefits and flexibility of integrating a Stirling engine with a metal hydride-based TES system and suggests that the MH TES technology, at its current level of development, provides a highly competitive alternative to lithium ion batteries for large scale grid energy storage applications.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2021

Techno-Economic Analysis of Chemical Precipitation Followed by Low Hydraulic Residence Time Biological Treatment, Including Ultrafiltration

This National Energy Technology Laboratory (NETL) analysis is a techno-economic evaluation of chemical precipitation followed by low hydraulic residence time biological treatment, which was identified as Best Available Technology for treatment and control of selenium emissions from wet flue gas desulfurization wastewater streams.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Techno-Economic Analysis of Large-Scale Hydrogen Production from Solid Oxide Electrolysis Cell Systems

The objective of this study is to establish a detailed techno-economic analysis to assess the effectiveness of incremental technology improvements needed for solid oxide electrolysis cell (SOEC) technology to achieve the U.S. DOE’s Hydrogen Shot goal of hydrogen production at less than $1 per kilogram. The pathway considers incremental technology improvements to key system parameters, with system performance and cost assessed for each pathway step. Briefly, the steps include cell voltage degradation rate improvements, operational current density increases, operating temperature reduction, improved steam utilization, increased system capacity factor, and reduced cell/stack capital costs. Each step is assessed at both atmospheric and pressurized (8 bar) operating conditions. To supplement assessment at each of these discrete stepwise improvements, sensitivity studies are conducted to understand the relative impact of each parameter and identify avenues for additional cost reductions. System efficiency and levelized costs of hydrogen (LCOH) for each case are presented. For the end-of-pathway case, which includes all the incremental research and development improvements, the cost of hydrogen produced is reduced by 50 percent from the state-of-the-art case.

08 HYDROGEN↗
DOE OSTI2021

Techno-Economic Analysis of Product Diversification Options for Sustainability of the Monticello and Prairie Island Nuclear Power Plants

The objective of this work was to perform techno-economic analysis (TEA) of hybrid options that could be integrated with light water reactor (LWR) nuclear power plants (NPPs) in order to improve the viability and sustainability of existing LWRs through product diversification by utilizing nuclear energy not only to produce grid electricity but to also produce carbon free products such as hydrogen, ammonia or synthetic fuels. Much of the analysis herein could be generally applied to any LWR (high temperature steam electrolysis- HTSE design), but hydrogen demand and the optimization of the HTSE was completed with specific collaboration and data from Xcel Energy’s Prairie Island and Monticello nuclear generating stations and the surrounding market and logistics potential in the greater Minneapolis region. Xcel Energy has set aggressive goals with regards to decarbonization, including an 80% reduction in CO 2 emissions from 2005 levels, by 2030 and 100% carbon free by 2050. Other TEAs regarding hydrogen production with nuclear energy have been completed in collaboration with other utility companies previously. Besides being the first TEA in this regard specific to Xcel Energy and the surrounding markets and logistics, this TEA adds to the previously completed TEAs by providing the most up to date and state of the art analysis and optimization of the hydrogen production plant integrated with nuclear power (NPP-HTSE).

08 HYDROGEN↗