Search NASA⌕ Search

SEARCH · Search NASA

Results for “thermal stress”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Vibration and local instability of thermally stressed plates

The vibration and buckling of a double wedge square cantilever plate has been investigated. It is shown that the free vibration modes, which occur at Delta T ref = 0, transition into the buckled modes which occur at Delta T ref = Delta T ref-cr for the respective mode. Delta T ref-cr for a particular mode is defined as the magnitude of thermal load at which the frequency of the particular mode vanishes. The analysis yields the same number of buckling eigenvalues and buckling modes as there are vibration eigenvalues and vibration modes. Gradual application of the load in the analysis permits the change in each vibration frequency of interest and its associated mode to be followed up to the load at which the frequency of the mode becomes zero. This constitutes the limit of linear theory. As the load is increased, the thin edges of the plate begin to deform during vibration. This local deformation, which begins in the vibration mode, is shown to transition into the phenomena of local edge buckling at Delta T ref-cr for the mode.

Bailey, C. D.↗
NASA NTRS1961

Experimental Investigation at Mach Number 3.0 of the Effects of Thermal Stress and Buckling on the Flutter of Four-Bay Aluminum Alloy Panels with Length-Width Ratios of 10

Skin-stiffener aluminum alloy panels consisting of four bays, each bay having a length-width ratio of 10, were tested at a Mach number of 3.0 at dynamic pressures ranging from 1,500 psf to 5,000 psf and at stagnation temperatures from 300 F to 655 F. The panels were restrained by the supporting structure in such a manner that partial thermal expansion of the skins could occur in both the longitudinal and lateral directions. A boundary faired through the experimental flutter points consisted of a flat-panel portion, a buckled-panel portion, and a transition point at the intersection of the two boundaries. In the region where a panel must be flat when flutter occurs, an increase in panel skin temperature (or midplane compressive stress) makes the panel more susceptible to flutter. In the region where a panel must be buckled when flutter occurs, the flutter trend is reversed. This reversal in trend is attributed to the panel postbuckling behavior.

Dixon, Sidney C.↗
NASA NTRS1990

Low-Thermal-Stress Structural Joints For Dissimilar Materials

Structural joint developed for attachment of hypersonic control surface to aircraft wing structure. Transmits large torque loads from composite control surface and torque tube to wing structure through metallic attachment lug and collar. Torque load transmitted from tube to collar by series of radially oriented cleats. Bearing surfaces of cleats plane passing through center-line of torque tube. Such joints accommodate differential thermal growth between parts of dissimilar materials. Potential for application to high-temperature structural joints associated with hypervelocity vehicles.

Matza, Edward C.↗
NASA NTRS1978

A simple element for multilayer beams in NASTRAN thermal stress analysis

In the application of NASTRAN, structural members are usually represented by bar elements with multipoint constraint cards to enforce the interface conditions. While this is a very powerful method in principle, it was found that in practice the process for specification of constraints became tedious and error prone, unless the geometry was simple and the number of grid points low. An alternative approach was found within the framework of the NASTRAN program. This approach made use of the idea that a thermal distortion in a multilayer beam may be similar to a homogeneous beam with a thermal gradient across the cross section. The exact mathematical derivation for the equivalent beam, and all the necessary formulae for the equivalent parameters in NASTRAN analysis are presented. Some numerical examples illustrate the simplicity and ease of this approach for finite element analysis.

Chen, W. T.↗
NASA NTRS2002

Residual Stresses in Thermal Barrier Coatings for a Cu-8Cr-4Nb Substrate System

Analytical calculations were conducted to determine the thermal stresses developed in a coated copper-based alloy, Cu-8%(at.%)Cr-4%Nb (designated as GRCop-84), after plasma spraying and during heat-up in a simulated rocket engine environment. Finite element analyses were conducted for two coating systems consisting of a metallic top coat, a pure copper bond coat and the GRCop-84. The through thickness temperature variations were determined as a function of coating thickness for two metallic coatings, a Ni-17%(wt%)Cr-6%Al-0.5%Y alloy and a Ni-50%(at.%)Al alloy. The residual stresses after low-pressure plasma spraying of the NiCrAlY and NiAl coatings on GRCop-84 substrate were also evaluated. These analyses took into consideration a 50.8 mm copper bond coat and the effects of an interface coating roughness. The through the thickness thermal stresses developed in coated liners were also calculated after 15 minutes of exposure in a rocket environment with and without an interfacial roughness.

Ghosn, Louis J.↗
NASA NTRS1973

Vibration and local edge buckling of thermally stressed, wedge airfoil cantilever wings.

The local edge buckling phenomena that can occur along the heated thin edge of a wedge shape airfoil is calculated. Qualitative comparison (qualitative only because the experimental temperature distribution was not measured) is made to the experimentally observed phenomena. The consequences of the assumption of identical vibration and buckling modes is shown by a comparison of results with and without the assumption of mode identity. Computer plots of the elastic surface as local buckling develops with increasing temperature are shown. The calculated, fully developed local edge buckling is compared to a photograph of a fully developed buckling as observed in the laboratory.

Bailey, C. D.↗
NASA NTRS1972

Residual thermal stress control in composite reinforced metal structures

Advanced composite materials, composed of boron or graphite fibers and a supporting matrix, make significant structural efficiency improvements available to aircraft and aerospace designers. Residual stress induced during bonding of composite reinforcement to metal structural elements can be reduced or eliminated through suitable modification to the manufacturing processes. The most successful method employed during this program used a steel tool capable of mechanically loading the metal component in compression prior to the adhesive bonding cycle. Compression loading combined with heating to 350 F during the bond cycle can result in creep deformation in aluminum components. The magnitude of the deformation increases with increasing stress level during exposure to 350 F.

Kelly, J. B.↗
NASA NTRS1975

Biogenic amines and acute thermal stress in the rat

A study is summarized which demonstrates that depletion of the biogenic amines 5-hydroxytryptamine (5-HT) or norepinephrine (NE) alters the normal thermoregulatory responses to acute temperature stress. Specifically, NE depletion caused a significant depression in equilibrium rectal temperature at 22 C and a greater depression in rectal temperature than controls in response to cold (6 C) stress; NE depletion also resulted in a significantly higher rectal temperature response to acute heat (38 C) stress. Depletion of 5-HT had less severe effects. It remains unclear whether the primary site of action of these agents is central or peripheral.

Williams, B. A.↗
NASA NTRS1976

Methods for testing high voltage connectors in vacuum, measurements of thermal stresses in encapsulated assemblies, and measurement of dielectric strength of electrodes in encapsulants versus radius of curvature

Internal embedment stress measurements were performed, using tiny ferrite core transformers, whose voltage output was calibrated versus pressure by the manufacturer. Comparative internal strain measurements were made by attaching conventional strain gages to the same type of resistors and encapsulating these in various potting compounds. Both types of determinations were carried out while temperature cycling from 77 C to -50 C.

Bever, R. S.↗
NASA NTRS1978

Temperature distributions and thermal stresses in a graded zirconia/metal gas path seal system for aircraft gas turbine engines

A ceramic/metallic aircraft gas turbine outer gas path seal designed for improved engine performance was studied. Transient temperature and stress profiles in a test seal geometry were determined by numerical analysis. During a simulated engine deceleration cycle from sea-level takeoff to idle conditions, the maximum seal temperature occurred below the seal surface, therefore the top layer of the seal was probably subjected to tensile stresses exceeding the modulus of rupture. In the stress analysis both two- and three-dimensional finite element computer programs were used. Predicted trends of the simpler and more easily usable two-dimensional element programs were borne out by the three-dimensional finite element program results.

Taylor, C. M.↗
NASA NTRS1984

Pre-stressed thermal protection systems

A hexagonal protective and high temperature resistant system for the Space Shuttle Orbiter consists of a multiplicity of pockets formed by hexagonally oriented spacer bars secured on the vehicle substructure. A packing of low density insulating batt material 18 in each pocket, and a thin protective panel of laterally resilient advanced carbon-carbon material surmounting the peripherals bars and packing. Each panel has three stepped or offset lips on contiguous edges. At the center of each pocket is a fully insulated stanchion secured to and connecting the substructure and panel for flexing the panel toward the substructure and thereby prestressing the panel and forcing the panel edges firmly against the spacer bars.

Dunn, T. J.↗