Search NASA⌕ Search

SEARCH · Search NASA

Results for “turbulence spreading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1997

An Experimental Study of Swirling Flows as Applied to Annular Combustors

This thesis presents an experimental study of swirling flows with direct applications to gas turbine combustors. Two separate flowfields were investigated: a round, swirling jet and a non-combusting annular combustor model. These studies were intended to allow both a further understanding of the behavior of general swirling flow characteristics, such as the recirculation zone, as well as to provide a base for the development of computational models. In order to determine the characteristics of swirling flows the concentration fields of a round, swirling jet were analyzed for varying amount of swirl. The experimental method used was a light scattering concentration measurement technique known as marker nephelometry. Results indicated the formation of a zone of recirculating fluid for swirl ratios (rotational speed x jet radius over mass average axial velocity) above a certain critical value. The size of this recirculation zone, as well as the spread angle of the jet, was found to increase with increase in the amount of applied swirl. The annular combustor model flowfield simulated the cold-flow characteristics of typical current annular combustors: swirl, recirculation, primary air cross jets and high levels of turbulence. The measurements in the combustor model made by the Laser Doppler Velocimetry technique, allowed the evaluation of the mean and rms velocities in the three coordinate directions, one Reynold's shear stress component and the turbulence kinetic energy: The primary cross jets were found to have a very strong effect on both the mean and turbulence flowfields. These cross jets, along with a large step change in area and wall jet inlet flow pattern, reduced the overall swirl in the test section to negligible levels. The formation of the strong recirculation zone is due mainly to the cross jets and the large step change in area. The cross jets were also found to drive a four-celled vortex-type motion (parallel to the combustor longitudinal axis) near the cross jet injection plane.

Seal, Michael Damian, II↗
NASA NTRS1997

Aspects of the Solar Tachocline

The splitting of the frequencies of p-mode multiplets enables information to be gained about the internal rotation of the sun. Such data have revealed a transition at the base of the convection zone from differential rotation similar to that observed at the surface to almost solid-body rotation in the radiative interior. This transition region, known as the tachocline, has been found to be relatively narrow and centered below the base of the convection zone. In this paper, the evolution of the transition region is investigated numerically. Without a large anisotropic viscosity, the depth to which it would spread in one solar age, under the assumption of a constant prescribed differential rotation at the base of the convection zone, is found to be greater than its extent as inferred from helioseismology. In the second part of the paper a highly anisotropic turbulent viscosity with a large horizontal component, as suggested by Spiegel & Zahn (1992), is assumed. In this case, a steady tachocline is formed in which the advection of angular momentum balances the Reynolds stresses. The horizontal component of turbulent viscosity required to match the thickness of the tachocline to that obtained by helioseismology, is estimated to be 5 x 1O sq cm/s The transport of helium is studied in this case and is found to yield a sound-speed increase similar to that required by helioseismology.

Elliott, J. R.↗
NASA NTRS2003

Highly Inclined Jets in Cross Flow

Results from an experimental investigation of flow field generated by pitched and yawed jets discharging from a flat plate into a cross-flow are presented. The circular jet was pitched at alpha = 20deg and 45deg and yawed between Beta = 0deg and 90deg in increments of 15deg. The measurements were performed with two ×-wires providing all three components of velocity and turbulent stresses. These data were obtained at downstream locations of x = 3, 5, 10 and 20, where the distance x, normalized by the jet diameter, is measured from the center of the orifice. Data for all configurations were acquired at a momentum-flux ratio J = 8. Additionally, for selected angles and locations, surveys were conducted for J = 1.5, 4, and 20. As expected, the jet penetration is found to be higher at larger alpha. With increasing beta the jet spreads more. The rate of reduction of peak streamwise vorticity, ω max, with the downstream distance is significantly less at higher Beta but is found to be practically independent of alpha. Thus, at the farthest measurement station x = 20, ωxmax is about five times larger for Beta = 75deg compared to the levels at Beta = 0deg. Streamwise velocity within the jet-vortex structure is found to depend on the parameter J. At J = 1.5 and 4, 'wake-like' velocity profiles are observed. In comparison, a 'jet-like' overshoot is present at higher J. Distributions of turbulent stresses for various cases are documented. Peak normal stresses are found to occur within the core of the streamwise vortices. With yaw, at lower values of J, high turbulence is also observed in the boundary layer underneath the jet-vortex structure

Milanovic, I. M.↗
NASA NTRS1979

Experimental studies of combustion in a two dimensional free shear layer

The effect of combustion on the turbulent free shear layer formed at a rearward facing step has been studied. Schlieren movies confirm the importance of large scale vortices in determining entrainment and mixing behavior. The movies, long exposure schlieren photographs, and laser anemometry velocity profiles are used to observe the spreading rate of the layer and to study the vortex formation process. It is concluded that to first order, the primary effect of combustion is felt through the change in density ratio across the layer and acceleration of the flow due to volumetric expansion of the fluid in a confined duct.

Pitz, R. W.↗
NASA NTRS1981

Experimental study of combustion in a turbulent free shear layer formed at a rearward facing step

A premixed propane-air flame is stabilized in a turbulent free shear layer formed at a rearward facing step. The mean and rms averages of the turbulent velocity flow field are determined by LDV for both reacting (equivalence ratio 0.57) and nonreacting flows (Reynolds number 15,000-37,000 based on step height). The effect of combustion is to shift the layer toward the recirculation zone and reduce the flame spread. For reacting flow, the growth rate is unchanged except very near the step. The probability density function of the velocity is bimodial near the origin of the reacting layer and single-peaked but often skewed elsewhere. Large-scale structures dominate the reacting shear layer. Measurements of their passing frequency from LDV are consistent with high-speed Schlieren movies of the reacting layer and indicate that the coalescence rate of the eddies in the shear layer is reduced by combustion.

Pitz, R. W.↗
NASA NTRS1997

Laser-Induced Incandescence in Microgravity

Microgravity offers unique opportunities for studying both soot growth and the effect of soot radiation upon flame structure and spread. LII has been characterized and developed at NASA-Lewis for soot volume fraction determination in a wide range of 1-g combustion applications. Reported here are the first demonstrations of LII performed in a microgravity environment. Examples are shown for laminar and turbulent gas-jet diffusion flames in 0-g.

VanderWal, Randall L.↗
NASA NTRS1975

Review of aircraft noise propagation

The current state of knowledge about the propagation of aircraft noise was reviewed. The literature on the subject is surveyed and methods for predicting the most important and best understood propagation effects are presented. Available empirical data are examined and the data's general validity is assessed. The methods used to determine the loss of acoustic energy due to uniform spherical spreading, absorption in a homogeneous atmosphere, and absorption due to ground cover are presented. A procedure for determining ground induced absorption as a function of elevation angle between source and receiver is recommended. Other factors that affect propagation, such as refraction and scattering due to turbulence, which were found to be less important for predicting the propagation of aircraft noise, are also evaluated.

Putnam, T. W.↗
NASA NTRS1987

An experimental study of the development of longitudinal vortex pairs embedded in a turbulent boundary layer

The mean streamwise development of pairs of longitudinal vortices embedded in an otherwise two-dimensional turbulent boundary layer was studied. Planes of closely spaced measurements of the three components of mean velocity were obtained at several streamwise locations, and the vorticity and circulation were calculated. Skin-friction measurements were also made. It was found that the rate of vorticity spreading in a vortex was greatly increased by close proximity of other vortices. The rate of streamwise circulation decrease was significantly greater for corotating vortices than for counter rotating vortices. Boundary-layer thinning and increased skin friction occured in regions where the secondary flow induced by the pairs was directed toward the wall; the boundary layer was thickened and skin friction reduced where the secondary flow was directed away from the wall.

Pauley, Wayne R.↗
NASA NTRS1995

Intense radio outburst from the supermassive star Eta Carinae

On five occasions between 1992 June 29 and 1994 May 3, we have used the Australia Telescope Compact Array (ATCA) to image Eta Carinae at a wavelength of 3 cm and a resolution of 1 arcsec. These observations have revealed remarkable activity. Since 1992 June, the total flux density has increase from 0.8 to 2.2 Jy, and the original single compact source has grown to a complex of sources spread over an area of about 16 sq arcsec. Strong hydrogen recombination-line spectral emission has appeared at the site of the strongest of these new sources. This recombination emission has the largest spectral width ever observed from a star, +/- 250 km/s, and reveals gas with turbulent velocities as great as 250 km/s approaching us at an average velocity of about 200 km/s. We believe that this radio outburst has been caused by a more than threefold increase of ultraviolet luminosity, and consequent ionization of previously neutral gas clouds.

Duncan, R. A.↗
NASA NTRS1981

Turbulent jet patterns in accelerating flows

Results of flow visualization experiments, and a semi-empirical model of a single turbulent jet injected perpendicularly to a different density cross flow are presented. The model is based on integral conservation equations, including the pressure terms appropriate to accelerating flow. It uses an entrainment correlation obtained from previous experiments of a jet in a cross stream. The results show trajectories and spreading rates, and are typified by a set of three parameters: momentum ratio, Froude number and density ratio. Agreement between test and calculated results is encouraging, but tend to be poorer with increasing momentum ratio.

Lipshitz, A.↗
NASA NTRS1991

Simulations of free shear layers using a compressible k-epsilon model

A two-dimensional, compressible Navier-Stokes equations with a k-epsilon turbulence model are solved numerically to simulate the flows of compressible free shear layers. The appropriate form of k and epsilon equations for compressible flows are discussed. Sarkar's modeling is adopted to simulate the compressibility effects in the k and epsilon equations. The numerical results show that the spreading rate of the shear layers decreases with increasing convective Mach number. In addition, favorable comparison was found between the calculated results and Goebel and Dutton's experimental data.

Yu, S. T.↗
NASA NTRS1991

On the scale of surface features in hypersonic swept shock boundary-layer interactions

A parametric study of a Mach 8 fin-induced shock interaction with a turbulent boundary layer was performed in a shock tunnel using surface oil-dot visualization and surface pressure measurements. The study showed that the interaction was separated and secondary separation was detected for the strongest cases studied. Although the inviscid shock wave was close to the fin, the interaction was spread over large angular extents. The interaction showed inception to conical symmetry at the highest shock strengths. Additionally, the surface pressure distribution showed an extensive plateau region, with no distinct dip associated with strongly separated interactions. Between the fin and the inviscid shock, the surface pressure rose rapidly but did not approach the downstream inviscid shock, the surface pressure rose rapidly but did not approach the downstream inviscid value.

Pace, E. G.↗
NASA NTRS1991

Simulations of free shear layers using a compressible kappa-epsilon model

A two-dimensional, compressible Navier-Stokes equation with a k-epsilon turbulence model is solved numerically to simulate the flow of a compressible free shear layer. The appropriate form of k and epsilon equations for compressible flow is discussed. Sarkar's modeling is adopted to simulate the compressibility effects in the k and epsilon equations. The numerical results show that the spreading rate of the shear layers decreases with increasing convective Mach number. In addition, favorable comparison was found between the calculated results and experimental data.

Yu, S. T.↗
NASA NTRS2001

Warm-Core Intensification Through Horizontal Eddy Heat Transports into the Eye

The mechanism for the formation and intensification of the hurricane warm core is not well understood. The generally accepted explanation is that the warm core forms as a result of gentle subsidence of air within the eye that warms as a result of adiabatic compression. Malkus suggested that this subsidence is part of a deep circulation in which air begins descent at high levels in the eye, acquires cyclonic angular momentum as it descends to lower levels, and then diverges at low levels, where it is entrained back into the eyewall. Inward mixing from the eyewall is hypothesized to force the subsidence and maintain the moisture and momentum budgets of the subsiding air. Willoughby suggested that air within the eye has remained so since it was first enclosed during the formation of the eyewall and that it subsides at most only a few kilometers rather than through the depth of the troposphere. He relates the subsidence to the low-level divergence and entrainment into the eyewall noted by Malkus, but suggests that shrinkage of the eye's volume is more than adequate to account for the air lost to the eyewall or converted to cloudy air by turbulent mixing across the eye boundary. Smith offered an alternative view of the subsidence forcing, suggesting that vertical motion in a mature hurricane eye is generated largely by imbalances between the downward vertical pressure gradient force and the upward buoyancy force. The vertical pressure gradient force is associated with the decay and/or radial spread of the tangential wind field with height at those levels were the winds are in approximate gradient wind balance. The rate of subsidence is just that required to warm the air sufficiently such that the buoyancy remains in close hydrostatic balance with an increasing vertical pressure gradient force. In this study, a very high-resolution simulation of Hurricane Bob using a cloud-resolving grid scale of 1.3 km is used to examine the heat budget within the storm with particular emphasis on the mechanisms for warming of the eye.

Braun, Scott A.↗
NASA NTRS1996

The Effect of Strain Rate on the Evolution of Plane Wakes Subjected to Irrotational Strains

Direct numerical simulations of time-evolving turbulent plane wakes developing in the presence of irrotational plane strain applied at three different strain rates have been generated. The strain geometry is such that the flow is compressed in the streamwise direction and expanded in the cross-stream direction with the spanwise direction being unstrained. This geometry is the temporally evolving analogue of a spatially evolving wake in an adverse pressure gradient. A pseudospectral numerical method with up to 16 million modes is used to solve the equations in a reference frame moving with the irrotational strain. The initial condition for each simulation is taken from a previous turbulent self-similar plane wake direct numerical simulation at a velocity deficit Reynolds number, Re, of about 2,000. Although the evolutions of many statistics are nearly collapsed when plotted against total strain, there are some differences owing to the different strain rate histories. The impact of strain-rate on the wake spreading rate, the peak velocity deficit, the Reynolds stress profiles, and the flow structure is examined.

Rogers, Michael M.↗
NASA NTRS1992

Studies of turbulent shear flows and their control

The intent of the original proposal and the work carried out under the grant was to explore the instabilities of turbulent free shear flows of an incompressible fluid. The purpose for doing so was that coherent instabilities are susceptible to control via upstream forcing and because at sufficient finite amplitudes, the coherent modes enter into nonlinear interactions with the mean motion and thus, through such nonlinear interactions, the control of mixing and of mean flow spreading can be effected through the control of the coherent structures.

Liu, Joseph T. C.↗
NASA NTRS1997

Laser-Induced Incandescence in Microgravity

Knowledge of soot concentration is important due to its presence and impact upon a wide range of combustion processes ranging from diffusion to premixed flames, laminar to turbulent processes and homogeneous to heterogeneous combustion. Measurement of soot volume fraction (f(sub v)) is essential to discerning its formation and growth. The presence of soot also affects other physical and chemical properties of combustion thereby affecting studies not directly concerned with either its formation or growth, such as radiative heat transfer, CO oxidation and fuel vaporization or pyrolysis rates. Microgravity offers unique opportunities for studying both soot growth and the effect of soot radiation upon flame structure and spread. Spatial scales and residence time scales are greatly extended in 0-g facilitating soot growth studies. With the varied geometries, short duration microgravity test times and time-varying processes there is a demand for measurement of f(sub v) with high spatial and temporal resolution. Laser-induced incandescence (LII) has advanced f(sub v) measurements in many 1-g combustion processes. To create laser-induced incandescence, a pulsed high intensity laser heats soot to incandescence temperatures. Using appropriate spectral and temporal detection conditions, the resulting incandescence can be selectively detected apart from the non-laser-heated soot and flame gases. Theoretical modelling and experiments have shown that the resulting incandescence is representative of f(sub v). Using an intensified array camera and a laser sheet for excitation, one- and two-dimensionally resolved LII images of f(sub v) have been obtained in 1-g. LII has been characterized and developed at NASA-Lewis for soot volume fraction determination in a wide range of 1-g combustion applications. Broadly grouped, the characterization work has included studies of excitation intensity, excitation wavelength and the optimum temporal and spectral detection conditions to enable an accurate representation of soot volume fraction by LII. Tests for special requirements imposed by different combustion processes have been performed in laminar and turbulent diffusion flames, rich sooting premixed flames, single droplet combustion, and other heterogeneous combustion. These studies demonstrated LII's high sensitivity, temporal and spatial capabilities and its geometric versatility. In contrast to the advantages offered to combustion studies by a microgravity environment, advanced diagnostics, specifically those requiring pulsed laser diagnostics have been limited due to the size, weight and power limitations in a low-gravity environment. Reported here are the first demonstrations of LII performed in a microgravity environment. Examples are shown for laminar and turbulent gas-jet diffusion flames in 0-g.

VanderWal, Randy L.↗
NASA NTRS1994

Recovering the fine structures in solar images

Several examples of the capability of the blind iterative deconvolution (BID) technique to recover the real point spread function, when limited a priori information is available about its characteristics. To demonstrate the potential of image post-processing for probing the fine scale and temporal variability of the solar atmosphere, the BID technique is applied to different samples of solar observations from space. The BID technique was originally proposed for correction of the effects of atmospheric turbulence on optical images. The processed images provide a detailed view of the spatial structure of the solar atmosphere at different heights in regions with different large-scale magnetic field structures.

Karovska, Margarita↗