Search NASA⌕ Search

SEARCH · Search NASA

Results for “web”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Defect structure of web silicon ribbon

The results of a preliminary study of two dendritic web samples are presented. The structure and electrical activity of the defects in the silicon webs were studied. Optical microscopy of chemically etched specimens was used to determine dislocation densities. Samples were mechanically polished, then Secco etched for approximately 5 minutes. High voltage transmission electron microscopy was used to characterize the crystallographic nature of the defects.

Cunningham, B.↗
NASA NTRS1980

Radiation tolerance of boron doped dendritic web silicon solar cells

The potential of dendritic web silicon for giving radiation hard solar cells is compared with the float zone silicon material. Solar cells with n(+)-p-P(+) structure and approximately 15% (AMl) efficiency were subjected to 1 MeV electron irradiation. Radiation tolerance of web cell efficiency was found to be at least as good as that of the float zone silicon cell. A study of the annealing behavior of radiation-induced defects via deep level transient spectroscopy revealed that E sub v + 0.31 eV defect, attributed to boron-oxygen-vacancy complex, is responsible for the reverse annealing of the irradiated cells in the temperature range of 150 to 350 C.

Rohatgi, A.↗
NASA NTRS1982

Silicon dendritic web material

The development of a low cost and reliable contact system for solar cells and the fabrication of several solar cell modules using ultrasonic bonding for the interconnection of cells and ethylene vinyl acetate as the potting material for module encapsulation are examined. The cells in the modules were made from dendritic web silicon. To reduce cost, the electroplated layer of silver was replaced with an electroplated layer of copper. The modules that were fabricated used the evaporated Ti, Pd, Ag and electroplated Cu (TiPdAg/Cu) system. Adherence of Ni to Si is improved if a nickel silicide can be formed by heat treatment. The effectiveness of Ni as a diffusion barrier to Cu and the ease with which nickel silicide is formed is discussed. The fabrication of three modules using dendritic web silicon and employing ultrasonic bonding for interconnecting calls and ethylene vinyl acetate as the potting material is examined.

Meier, D. L.↗
NASA NTRS1982

Large-area sheet task advanced dendritic web growth development

The thermal stress model was used to generate the design of a low stress lid and shield configuration, which was fabricated and tested experimentally. In preliminary tests, the New Experimental Web Growth Facility performed as designed, producing web on the first run. These experiments suggested desirable design modifications in the melt level sensing system to improve further its performance, and these are being implemented.

Duncan, C. S.↗
NASA NTRS1985

Production Line for Dendritic-Web Solar Cells

Direct inclusion of web-growth furnaces in production line expected to result in lower costs than current production processes using silicon wafers sliced from Czochralski boules. Silicon-web input capacity of line is 0.5 m2/min, which corresponds to total peak-power output of about 25 MW for 1 year of production. Line employs about 18 production people per shift and requires about 3,650 square feet of floorspace.

Page, D. J.↗
NASA NTRS1985

Silicon-Web-Growing Machine

Silicon replenished automatically as web is withdrawn. Semiautomatic silicon-web-growing machine set down in detailed engineering drawings. Melt level sensed with He/Ne laser beam and melt-level error signal used to control motor-driven pellet feeder, speeding up when level is low. System reduces demand upon operator's time.

Duncan, C.↗
NASA NTRS1984

Development of high-efficiency solar cells on silicon web

The development of high efficiency solar cells on a silicon web is discussed. Heat treatment effects on web quality; the influence of twin plane lamellae, trace impurities and stress on minority carrier lifetime; and the fabrication of cells are discussed.

Rohatgi, A.↗
NASA NTRS1985

Fabrication and evaluation of superplastically formed/weld-brazed corrugated compression panels with beaded webs

A study was made to investigate the feasibility of superplastically forming corrugated panels with beaded webs and to demonstrate the structural integrity of these panels by testing. The test panels in the study consist of superplastically formed titanium alloy Ti-6Al-4V half-hat elements that are joined by weld-brazing to titanium alloy Ti-6Al-4V caps to form either single-corrugation compression panels or multiple-corrugation compression panels. Stretching and subsequent thinning of the titanium sheet during superplastic forming is reduced by approximately 35 percent with a shallow half-hat die concept instead of a deep die concept and results in a more uniform thickness across the beaded webs. The complete panels are tested in end compression at room temperature and the results compared with analysis. The heavily loaded panels failed at loads approaching the yield strength of the titanium material. At maximum load, the caps wrinkled locally accompanied with separation of the weld-braze joint in the wrinkle. None of the panels tested, however, failed catastrophically in the weld-braze joint. Experimental test results are in good agreement with structural analysis of the panels.

Royster, D. M.↗
NASA NTRS1985

Web team overview

Analytical and experimental work were combined to develop a stress model to determine the temperature profile which will yield a satisfactory web. A thermal model of the web will be used to determine the thermal configuration which will yield the desired temperature profile. Thermal analysis of growth interface and the susceptor melt will be developed to determine a thermal configuration which will improve stability of growth process. The thermal configurations will be designed, fabricated, and tested and the results fed back into the models.

Mcdonald, R. R.↗
NASA NTRS1985

Advanced dendritic web growth development

A program to develop the technology of the silicon dendritic web ribbon growth process is examined. The effort is being concentrated on the area rate and quality requirements necessary to meet the JPL/DOE goals for terrestrial PV applications. Closed loop web growth system development and stress reduction for high area rate growth is considered.

Hopkins, R. H.↗
NASA NTRS1987

Thermal Stresses in Silicon-Web Growth

Mathematical model represents thermomechanical behavior of solid web of rectangular cross section as pulled from melt of same material. Intended for application to growth of silicon webs or ribbons, model general enough to be applicable to other materials as well. Shows suitable temperature distribution results in stress-free ribbon. Conceptual ribbon of rectangular cross section pulled from melt. Simplified configuration used to calculate thermal conditions for stress-free ribbon.

Wade, Ben K.↗
NASA NTRS1986

JPL web team

The Jet Propulsion Laboratory (JPL) WEB Team activities were reported for activities which were directed toward identifying and attacking areas in the growth of dendritic web ribbon, to complement the program at Westinghouse Electric Corp.

Bickler, D. B.↗
NASA NTRS1986

Development of high-efficiency solar cells on silicon web

Achievement of higher efficiency cells by directing efforts toward identifying carrier loss mechanisms; design of cell structures; and development of processing techniques are described. Use of techniques such as deep-level transient spectroscopy (DLTS), laser-beam-induced current (LBIC), and transmission electron microscopy (TEM) indicated that dislocations in web material rather than twin planes were primarily responsible for limiting diffusion lengths in the web. Lifetimes and cell efficiencies can be improved from 19 to 120 microns, and 8 to 10.3% (no AR), respectively, by implanting hydrogen at 1500 eV and a beam current density of 2.0 mA/sq cm. Some of the processing improvements included use of a double-layer AR coating (ZnS and MgF2) and an addition of an aluminum back surface reflectors. Cells of more than 16% efficiency were achieved.

Meier, D. L.↗
NASA NTRS1986

Advanced dendritic web growth development and development of single-crystal silicon dendritic ribbon and high-efficiency solar cell program

Efforts to demonstrate that the dendritic web technology is ready for commercial use by the end of 1986 continues. A commercial readiness goal involves improvements to crystal growth furnace throughput to demonstrate an area growth rate of greater than 15 sq cm/min while simultaneously growing 10 meters or more of ribbon under conditions of continuous melt replenishment. Continuous means that the silicon melt is being replenished at the same rate that it is being consumed by ribbon growth so that the melt level remains constant. Efforts continue on computer thermal modeling required to define high speed, low stress, continuous growth configurations; the study of convective effects in the molten silicon and growth furnace cover gas; on furnace component modifications; on web quality assessments; and on experimental growth activities.

Duncan, C. S.↗
NASA NTRS1987

High temperature (900-1300 C) mechanical behaviour of dendritic web grown silicon ribbons - Strain rate and temperature dependence of the yield stress

The mechanical behavior of dendritic web Si ribbons close the melting point was studied experimentally. The goal of the study was to generate data for modeling the generation of stresses and dislocation structures during growth of dendritic web Si ribbons, thereby permitting modifications to the production process, i.e., the temperature profile, to lower production costs for the photovoltaic ribbons. A laser was used to cut specimens in the direction of growth of sample ribbons, which were then subjected to tensile tests at temperatures up to 1300 C in an Ar atmosphere. The tensile strengths of the samples increased when the temperature rose above 1200 C, a phenomena which was attributed to the diffusion of oxygen atoms to the quasi-dislocation sites. The migration to the potential dislocations sites effectively locked the dislocations.

Mathews, V. K.↗
NASA NTRS1987

Analysis of plastic deformation in silicon web crystals

Numerical calculation of 111-plane 110-line slip activity in silicon web crystals generated by thermal stresses is in good agreement with etch pit patterns and X-ray topographic data. The data suggest that stress redistribution effects are small and that a model, similar to that proposed by Penning (1958) and Jordan (1981) but modified to account for dislocation annihilation and egress, can be used to describe plastic flow effects during silicon web growth.

Spitznagel, J. A.↗
NASA NTRS1987

Advancements in silicon web technology

Low defect density silicon web crystals up to 7 cm wide are produced from systems whose thermal environments are designed for low stress conditions using computer techniques. During growth, the average silicon melt temperature, the lateral melt temperature distribution, and the melt level are each controlled by digital closed loop systems to maintain thermal steady state and to minimize the labor content of the process. Web solar cell efficiencies of 17.2 pct AM1 have been obtained in the laboratory while 15 pct efficiencies are common in pilot production.

Hopkins, R. H.↗
NASA NTRS1991

Test of superplastically formed corrugated aluminum compression specimens with beaded webs

Corrugated wall sections provide a highly efficient structure for carrying compressive loads in aircraft and spacecraft fuselages. The superplastic forming (SPF) process offers a means to produce complex shells and panels with corrugated wall shapes. A study was made to investigate the feasibility of superplastically forming 7475-T6 aluminum sheet into a corrugated wall configuration and to demonstrate the structural integrity of the construction by testing. The corrugated configuration selected has beaded web segments separating curved-cap segments. Eight test specimens were fabricated. Two specimens were simply a single sheet of aluminum superplastically formed to a beaded-web, curved-cap corrugation configuration. Six specimens were single-sheet corrugations modified by adhesive bonding additional sheet material to selectively reinforce the curved-cap portion of the corrugation. The specimens were tested to failure by crippling in end compression at room temperature.

Davis, Randall C.↗