Results for “well orientation” — Page 11

NASA NTRS2007

Gratings and Random Reflectors for Near-Infrared PIN Diodes

Crossed diffraction gratings and random reflectors have been proposed as means to increase the quantum efficiencies of InGaAs/InP positive/intrinsic/ negative (PIN) diodes designed to operate as near-infrared photodetectors. The proposal is meant especially to apply to focal-plane imaging arrays of such photodetectors to be used for near-infrared imaging. A further increase in quantum efficiency near the short-wavelength limit of the near-infrared spectrum of such a photodetector array could be effected by removing the InP substrate of the array. The use of crossed diffraction gratings and random reflectors as optical devices for increasing the quantum efficiencies of quantum-well infrared photodetectors (QWIPs) was discussed in several prior NASA Tech Briefs articles. While the optical effects of crossed gratings and random reflectors as applied to PIN photodiodes would be similar to those of crossed gratings and random reflectors as applied to QWIPs, the physical mechanisms by which these optical effects would enhance efficiency differ between the PIN-photodiode and QWIP cases: In a QWIP, the multiple-quantum-well layers are typically oriented parallel to the focal plane and therefore perpendicular or nearly perpendicular to the direction of incidence of infrared light. By virtue of the applicable quantum selection rules, light polarized parallel to the focal plane (as normally incident light is) cannot excite charge carriers and, hence, cannot be detected. A pair of crossed gratings or a random reflector scatters normally or nearly normally incident light so that a significant portion of it attains a component of polarization normal to the focal plane and, hence, can excite charge carriers. A pair of crossed gratings or a random reflector on a PIN photodiode would also scatter light into directions away from the perpendicular to the focal plane. However, in this case, the reason for redirecting light away from the perpendicular is to increase the length of the optical path through the detector to increase the probability of absorption of photons and thereby increase the resulting excitation of charge carriers. A pair of crossed gratings or a random reflector according to the proposal would be fabricated as an integral part of photodetector structure on the face opposite the focal plane (see figure). In the presence of crossed gratings, light would make four passes through the device before departing. In the presence of a random reflector, a significant portion of the light would make more than four passes: After each bounce, light would be scattered at a different random angle, and would have a chance to escape only when it was reflected, relative to the normal, at an angle less than the critical angle for total internal reflection. Given the indices of refraction of the photodiode materials, this angle would be about 17 . This amounts to a very narrow cone for escape of trapped light.

Gunapala, Sarath↗

NASA NTRS2003

Space Environment Factors Affecting the Performance of International Space Station Materials: The First Two Years of Flight Operations

In this paper, the natural and induced space environment factors affecting materials performance on ISS are described in some detail. The emphasis will be on ISS flight experience and the more significant design and development issues of the last two years. The intent is to identify and document the set of space environment factors, affecting materials, that are producing the largest impacts on the ISS flight hardware verification and acceptance process and on ISS flight operations. Orbital inclination (S1.6 ) and altitude (nominal3S0 km to 400 km altitude) determine the set of natural environment factors affecting the functional life of materials and subsystems on ISS. ISS operates in the F2 region of Earth's ionosphere in well-defined fluxes of atomic oxygen, other ionospheric plasma species, and solar UV, VUV, and x-ray radiation, as well as galactic cosmic rays, trapped radiation, and solar cosmic rays (1,2). The high latitude orbital environment also exposes external surfaces to significantly less well-defined or predictable fluxes of higher energy trapped electrons and auroral electrons (3 ,4). The micrometeoroid and orbital debris environment is an important determinant of spacecraft design and operations in any orbital inclination. Environment factors induced by ISS flight operations include ram-wake effects, magnetic induction voltages arising from flight through Earth's magnetic field, hypergolic thruster plume impingement from proximity operations of visiting vehicles, materials outgassing, venting and dumping of fluids, ISS thruster operations, as well as specific electrical power system interactions with the ionospheric plasma (S-7). ISS must fly in a very limited number of approved flight attitudes leading to location specific environmental exposures and extreme local thermal environments (8). ISS is a large vehicle and produces a deep wake structure from which both ionospheric plasma and neutrals (atomic oxygen) are largely excluded (9-11). At high latitude, the ISS wake may produce a spacecraft charging environment similar to that experienced by the DMSP and Freja satellites (800 to 100 km altitude polar orbits), especially during geo-magnetic disturbances (12-14). ISS is also subject to magnetic induction voltages (VxB L) on conducting structure, a result of high velocity flight through Earth's magnetic field. The magnitude of the magnetic induction voltage varies with location on ISS, as well as the relative orientation of the vehicle velocity vector and planetary magnetic field vector, leading to maximum induction voltages at high latitude (15). The space environment factors, natural and induced, that have had the largest impact on pre-launch ISS flight hardware verification and flight operations during the first two years of ISS flight operations are listed below and grouped according to the physical and chemical processes driving their interaction with ISS materials.

Koontz, Steven L.↗

NASA NTRS2003

Metal Side Reflectors for Trapping Light in QWIPs

Focal-plane arrays of quantum-well infrared photodetectors (QWIPs) equipped with both light-coupling diffraction gratings and metal side reflectors have been proposed, and prototypes are expected to be fabricated soon. The purpose served by the metal side reflectors is to increase quantum efficiency by helping to trap light in the photosensitive material of each pixel. The reasons for using diffraction gratings were discussed in several prior NASA Tech Briefs articles. To recapitulate: In an array of QWIPs, the quantum-well layers are typically oriented parallel to the focal plane and therefore perpendicular or nearly perpendicular to the direction of incidence of infrared light. By virtue of the applicable quantum selection rules, light polarized parallel to the focal plane (as normally incident light is) cannot excite charge carriers and, hence, cannot be detected. Diffraction gratings scatter normally or nearly normally incident light into directions more nearly parallel to the focal plane, so that a significant portion of the light attains a component of polarization normal to the focal plane and, hence, can excite charge carriers. Unfortunately, light scattered in directions parallel or nearly parallel to the focal plane can escape sideways from the QWIP of a given pixel, as illustrated in Figure 1. The escaped light has made only a single pass through the interior photosensitive volume of the QWIP. The quantum efficiency of the QWIP would be increased by trapping light so that it makes multiple passes through the photosensitive volume. As shown in Figure 2, the sides of the QWIP of each pixel would be coated with gold to reflect escaping light back into the interior.

Gunapala, Sarath↗

NASA NTRS2012

Gravity Wave Variances and Propagation Derived from AIRS Radiances

As the first gravity wave (GW) climatology study using nadir-viewing infrared sounders, 50 Atmospheric Infrared Sounder (AIRS) radiance channels are selected to estimate GW variances at pressure levels between 2-100 hPa. The GW variance for each scan in the cross-track direction is derived from radiance perturbations in the scan, independently of adjacent scans along the orbit. Since the scanning swaths are perpendicular to the satellite orbits, which are inclined meridionally at most latitudes, the zonal component of GW propagation can be inferred by differencing the variances derived between the westmost and the eastmost viewing angles. Consistent with previous GW studies using various satellite instruments, monthly mean AIRS variance shows large enhancements over meridionally oriented mountain ranges as well as some islands at winter hemisphere high latitudes. Enhanced wave activities are also found above tropical deep convective regions. GWs prefer to propagate westward above mountain ranges, and eastward above deep convection. AIRS 90 field-of-views (FOVs), ranging from +48 deg. to −48 deg. off nadir, can detect large-amplitude GWs with a phase velocity propagating preferentially at steep angles (e.g., those from orographic and convective sources). The annual cycle dominates the GW variances and the preferred propagation directions for all latitudes. Indication of a weak two-year variation in the tropics is found, which is presumably related to the Quasi-biennial oscillation (QBO). AIRS geometry makes its out-tracks capable of detecting GWs with vertical wavelengths substantially shorter than the thickness of instrument weighting functions. The novel discovery of AIRS capability of observing shallow inertia GWs will expand the potential of satellite GW remote sensing and provide further constraints on the GW drag parameterization schemes in the general circulation models (GCMs).

AIRS↗

NASA NTRS2020

Integrated Concurrent Engineering Teams for Increased Efficiency in Flight Projects

A highly integrated Concurrent Engineering Team (CET) within a flight project evolves in its function and has the potential to provide many benefits through the project lifecycle. The benefits include superior systems-oriented design products, as well as overall improved project efficiency and higher-performing interpersonal relationships within the project. If physically integrated, this can manifest as a Concurrent Engineering Center (CEC) centrally located within a project’s physical office space. Here we discuss the process to establish and maintain a tightly integrated engineering and design team for providing highly streamlined service to the project, including a cost/benefits analysis discussion.

Flight Project↗

NASA NTRS2020

Integrated Concurrent Engineering Teams for Increased Efficiency in Flight Projects

A highly integrated Concurrent Engineering Team (CET) within a flight project evolves in its function and has the potential to provide many benefits through the project lifecycle. The benefits include superior systems-oriented design products, as well as overall improved project efficiency and higher-performing interpersonal relationships within the project. If physically integrated, this can manifest as a Concurrent Engineering Center (CEC) centrally located within a project’s physical office space. Here we discuss the process to establish and maintain a tightly integrated engineering and design team for providing highly streamlined service to the project, including a cost/benefits analysis discussion.

Flight Project↗

NASA NTRS2018

Autonomous Small Body Mapping and Spacecraft Navigation

Current methods for pose and shape estimation of small bodies, such as comets and asteroids, rely on extensive ground support and signiﬁcant use of radiometric measurements using the Deep Space Network. The Stereo-Photoclinometry (SPC) technique is currently used to provide detailed topological information about a small body as well as its absolute orientation and position. While this technique has produced very accurate estimates, the core algorithm cannot be run in real-time and requires a team of scientists on the ground who must communicate with the spacecraft in order to oversee SPC operations. Autonomous onboard navigation addresses these limitations by eliminating the need for human oversight. In this paper, we present an optimization-based estimation algorithm for navigation that allows the spacecraft to autonomously approach and maneuver around an unknown small body by mapping its geometric shape, estimating its orientation, and simultaneously determining the trajectory of the center of mass of the small body. We show the eﬀectiveness of the proposed algorithm using simulated data from a previous ﬂight mission to Comet 67P.

Bhaskaran, Shyamkumar↗

NASA NTRSDate not supplied

Pressure Fluctuation Spectral Peaks Due to ‘Guided Waves’ in Regions Upstream of the Jet Exit

Pressure fluctuation spectral peaks due to ‘guided’ (or ‘trapped’) waves in compressible jets in regions upstream of the nozzle exit are investigated experimentally. These spectral peaks are known to disappear in the far acoustic field on the sideline and in the downstream direction, where noise measurements are done typically. The data in this paper show that they are prevalent in the far upstream regions of the ‘forward arc’, at shallow angles relative to the jet axis. This is noted with a round as well as a rectangular jet. The result is significant since such spectral behavior is not predicted by existing noise prediction codes. The experimental results not only expand our understanding of the trapped wave phenomenon but may also aid in refining noise prediction codes for basic as well as application-oriented propulsion systems.

Jets↗

NASA NTRS2024

Molecular Dynamics Simulations of Microstructural Effects on Austenite-Martensite Interfaces in NiTi

Formation and migration of austenite-martensite interfaces plays the key role in reversible martensitic transformations of shape memory alloys (SMAs). How these interfaces interact with the SMA microstructure is a primary determining factor in important functional properties such as hysteresis and transformation span. As such, successful microstructural engineering of SMAs requires in-depth knowledge of interface behavior. The rapid nature of martensitic transformations makes experimental observations of moving austenite-martensite interfaces challenging. Molecular dynamics (MD) simulation is a unique tool which can probe the atomic-scale details of austenite-martensite interfaces as they migrate through different microstructures. However, in focusing on the entire transformation process, including the nucleation of new phases, MD studies are usually performed so far from equilibrium that their relevance to experiment is questionable. Here, we demonstrate new MD techniques to generate energetically preferred austenite-martensite interfaces in NiTi under near-equilibrium conditions. The interfaces are semi-coherent, exhibiting a series of structural disconnections, and they can migrate rapidly through single crystals under only small thermodynamic driving forces. In contrast, when interfaces migrate in polycrystals, their motion is impeded by thermoelastic effects as well as changes in orientation relationships at grain boundaries. Microstructures which accumulate large amounts of elastic energy tend to release some fraction through irreversible, hysteresis-inducing mechanisms. We demonstrate that engineering microstructures with less constraints is a viable strategy to produce SMAs with reduced hysteresis and transformation span. Similar thermoelastic and hysteresis-inducing mechanisms also arise when austenite-martensite interfaces encounter precipitates and can be controlled by tuning characteristics of the precipitate distribution.

Gabriel Plummer↗

NASA NTRSDate not supplied

Molecular Dynamics Simulations of Microstructural Effects on Austenite-Martensite Interfaces in NiTi

The formation and migration of austenite-martensite interfaces plays the key role in reversible martensitic transformations of shape memory alloys (SMAs). How these interfaces interact with the SMA microstructure is a primary determining factor in important functional properties such as hysteresis and transformation span. As such, successful microstructural engineering of SMAs requires in-depth knowledge of interface behavior. The rapid nature of martensitic transformations makes experimental observations of moving austenite-martensite interfaces challenging. Molecular dynamics (MD) simulation is a unique tool which can probe the atomic-scale details of austenite-martensite interfaces as they migrate through different microstructures. However, in focusing on the entire transformation process, including the nucleation of new phases, MD studies are usually performed so far from equilibrium that their relevance to experiment is questionable. Here, we demonstrate new MD techniques to generate energetically preferred austenite-martensite interfaces in NiTi under near-equilibrium conditions. The interfaces are semi-coherent, exhibiting a series of structural disconnections, and they can migrate rapidly through single crystals under only small thermodynamic driving forces. In contrast, when interfaces migrate in polycrystals, their motion is impeded by thermoelastic effects as well as changes in orientation relationships at grain boundaries. Microstructures which accumulate large amounts of elastic energy tend to release some fraction through irreversible, hysteresis-inducing mechanisms. We demonstrate that engineering microstructures with less constraints is a viable strategy to produce SMAs with reduced hysteresis and transformation span. Similar thermoelastic and hysteresis-inducing mechanisms also arise when austenite-martensite interfaces encounter precipitates and can be controlled by tuning characteristics of the precipitate distribution.

Gabriel Plummer↗

NASA NTRSDate not supplied

Molecular Dynamics Simulations of Microstructural Effects on Austenite-Martensite Interfaces in NiTi

Formation and migration of austenite-martensite interfaces plays the key role in reversible martensitic transformations of shape memory alloys (SMAs). How these interfaces interact with the SMA microstructure is a primary determining factor in important functional properties such as hysteresis and transformation span. As such, successful microstructural engineering of SMAs requires in-depth knowledge of interface behavior. The rapid nature of martensitic transformations makes experimental observations of moving austenite-martensite interfaces challenging. Molecular dynamics (MD) simulation is a unique tool which can probe the atomic-scale details of austenite-martensite interfaces as they migrate through different microstructures. However, in focusing on the entire transformation process, including the nucleation of new phases, MD studies are usually performed so far from equilibrium that their relevance to experiment is questionable. Here, we demonstrate new MD techniques to generate energetically preferred austenite-martensite interfaces in NiTi under near-equilibrium conditions. The interfaces are semi-coherent, exhibiting a series of structural disconnections, and they can migrate rapidly through single crystals under only small thermodynamic driving forces. In contrast, when interfaces migrate in polycrystals, their motion is impeded by thermoelastic effects as well as changes in orientation relationships at grain boundaries. Microstructures which accumulate large amounts of elastic energy tend to release some fraction through irreversible, hysteresis-inducing mechanisms. We demonstrate that engineering microstructures with less constraints is a viable strategy to produce SMAs with reduced hysteresis and transformation span. Similar thermoelastic and hysteresis-inducing mechanisms also arise when austenite-martensite interfaces encounter precipitates and can be controlled by tuning characteristics of the precipitate distribution.

Gabriel Plummer↗

DOE OSTI2025

Controlling Preferred Grain Orientation in Vapor-Deposited Metal-Halide Perovskite Thin Films

Metal-halide perovskites are promising semiconductor materials for light-absorber layers in solar cells due to their optimized band gap, defect tolerance, and relative ease of synthesis. In this work, we demonstrate the viability of vapor transport deposition (VTD), a solvent-free processing method, to realize polycrystalline films of both lead iodide (PbI 2 ) and methylammonium lead iodide (MAPbI 3 ) perovskites showing preferential crystallographic orientation. Notable is the difference in perovskite film texturing observed for sequentially and co-deposited VTD films of MAPbI 3 , as well as the lack of strong preferential orientation in solution-processed MAPbI 3 films. While sequential deposition of the perovskite precursors PbI 2 and methylammonium iodide (MAI) leads to a MAPbI 3 film with a limited preferential grain orientation, co-deposited MAPbI 3 films mirror the orientation of excess PbI 2 present in the film. The latter is confirmed by the similar dependence of preferential orientation for PbI 2 and co-deposited MAPbI 3 on underlayer roughness, as well as the emergence of preferential orientation in MAPbI 3 only when excess PbI 2 is present. Both MAPbI 3 and PbI 2 films show a strong preferred lattice orientation on smooth substrates, while on rougher substrates, this orientation is disrupted. Furthermore, these results are interpreted as excess PbI 2 frustrating the diffusion of MAI in the film, which would otherwise disrupt the preferred orientation, pointing to a notable difference in lattice orientation arising from processing technique and conditions.

Deposition↗

DOE OSTI2021

Shape- and Orientation-Dependent Scattering of Isolated Gold Nanostructures Using Polarized Dark-Field Microscopy

In this work, we demonstrate a simple and robust method for measuring the shape- and orientation-dependent optical scattering of various plasmonic nanostructures adsorbed onto a solid surface using polarized dark-field microscopy. By analyzing the dark-field scattering images of gold nanostructures using grazing incidence polarized light with a bench-top microscope, we are able to correlate optical scattering from the individual nanostructures with their shape and orientation. Depending on the size, shape, and orientation of the plasmonic nanostructures, they exhibit characteristic angle- and polarization-dependent scattering signals. Extracting the red, green, and blue channels of the scattering signals from a color-imaging detector as a function of azimuthal angle provides a polar plot of color intensity values that is characteristic of the underlying nanostructure. Examples are presented for various nanostructures, including spherical nanoparticles, nanotriangles, and nanorods. Experimental results are complemented by numerical calculations of the scattering spectra of representative model nanostructures. We demonstrate that the polarization- and orientation-dependent scattering behavior is a consequence of various localized surface plasmon modes existing in the nanostructures and can be used to verify the shape of individual objects as well as quickly identify the orientation of numerous objects on a densely populated substrate. We anticipate that this method will provide a rapid and efficient complement to the typical structural analysis of nanoparticles that is achieved by electron microscopy as well as providing a simple method for generating detailed information of the optical scattering of various types of individual plasmonic nanostructures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Strategies for Controlling the Spatial Orientation of Single Molecules Tethered on DNA Origami Templates Physisorbed on Glass Substrates: Intercalation and Stretching

Nanoarchitectural control of matter is crucial for next-generation technologies. DNA origami templates are harnessed to accurately position single molecules; however, direct single molecule evidence is lacking regarding how well DNA origami can control the orientation of such molecules in three-dimensional space, as well as the factors affecting control. Here, we present two strategies for controlling the polar (θ) and in-plane azimuthal (Φ) angular orientations of cyanine Cy5 single molecules tethered on rationally-designed DNA origami templates that are physically adsorbed (physisorbed) on glass substrates. By using dipolar imaging to evaluate Cy5's orientation and super-resolution microscopy, the absolute spatial orientation of Cy5 is calculated relative to the DNA template. The sequence-dependent partial intercalation of Cy5 is discovered and supported theoretically using density functional theory and molecular dynamics simulations, and it is harnessed as our first strategy to achieve θ control for a full revolution with dispersion as small as ±4.5°. In our second strategy, Φ control is achieved by mechanically stretching the Cy5 from its two tethers, being the dispersion ±10.3° for full stretching. These results can in principle be applied to any single molecule, expanding in this way the capabilities of DNA as a functional templating material for single-molecule orientation control. The experimental and modeling insights provided herein will help engineer similar self-assembling molecular systems based on polymers, such as RNA and proteins.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

NASA NTRS1980

Fine-scale characteristics of interplanetary sector

The structure of the interplanetary sector boundaries observed by Helios 1 within sector transition regions was studied. Such regions consist of intermediate (nonspiral) average field orientations in some cases, as well as a number of large angle directional discontinuities (DD's) on the fine scale (time scales 1 hour). Such DD's are found to be more similar to tangential than rotational discontinuities, to be oriented on average more nearly perpendicular than parallel to the ecliptic plane to be accompanied usually by a large dip ( 80%) in B and, with a most probable thickness of 3 x 10 to the 4th power km, significantly thicker previously studied. It is hypothesized that the observed structures represent multiple traversals of the global heliospheric current sheet due to local fluctuations in the position of the sheet. There is evidence that such fluctuations are sometimes produced by wavelike motions or surface corrugations of scale length 0.05 - 0.1 AU superimposed on the large scale structure.

Behannon, K. W.↗

NASA NTRS2004

Grid Technology as a Cyber Infrastructure for Earth Science Applications

This paper describes how grids and grid service technologies can be used to develop an infrastructure for the Earth Science community. This cyberinfrastructure would be populated with a hierarchy of services, including discipline specific services such those needed by the Earth Science community as well as a set of core services that are needed by most applications. This core would include data-oriented services used for accessing and moving data as well as computer-oriented services used to broker access to resources and control the execution of tasks on the grid. The availability of such an Earth Science cyberinfrastructure would ease the development of Earth Science applications. With such a cyberinfrastructure, application work flows could be created to extract data from one or more of the Earth Science archives and then process it by passing it through various persistent services that are part of the persistent cyberinfrastructure, such as services to perform subsetting, reformatting, data mining and map projections.

Hinke, Thomas H.↗

NASA NTRS1984

Ceramic microstructure and adhesion

When a ceramic is brought into contact with a ceramic, a polymer, or a metal, strong bond forces can develop between the materials. The bonding forces will depend upon the state of the surfaces, cleanliness and the fundamental properties of the two solids, both surface and bulk. Adhesion between a ceramic and another solid are discussed from a theoretical consideration of the nature of the surfaces and experimentally by relating bond forces to interface resulting from solid state contact. Surface properties of ceramics correlated with adhesion include, orientation, reconstruction and diffusion as well as the chemistry of the surface specie. Where a ceramic is in contact with a metal their interactive chemistry and bond strength is considered. Bulk properties examined include elastic and plastic behavior in the surficial regions, cohesive binding energies, crystal structures and crystallographic orientation. Materials examined with respect to interfacial adhesive interactions include silicon carbide, nickel zinc ferrite, manganese zinc ferrite, and aluminum oxide. The surfaces of the contacting solids are studied both in the atomic or molecularly clean state and in the presence of selected surface contaminants.

Buckley, D. H.↗

NASA NTRS1985

Ceramic microstructure and adhesion

When a ceramic is brought into contact with a ceramic, a polymer, or a metal, strong bond forces can develop between the materials. The bonding forces will depend upon the state of the surfaces, cleanliness and the fundamental properties of the two solids, both surface and bulk. Adhesion between a ceramic and another solid are discussed from a theoretical consideration of the nature of the surfaces and experimentally by relating bond forces to interface resulting from solid state contact. Surface properties of ceramics correlated with adhesion include, orientation, reconstruction and diffusion as well as the chemistry of the surface specie. Where a ceramic is in contact with a metal their interactive chemistry and bond strength is considered. Bulk properties examined include elastic and plastic behavior in the surficial regions, cohesive binding energies, crystal structures and crystallographic orientation. Materials examined with respect to interfacial adhesive interactions include silicon carbide, nickel zinc ferrite, manganese zinc ferrite, and aluminum oxide. The surfaces of the contacting solids are studied both in the atomic or molecularly clean state and in the presence of selected surface contaminants.

Buckley, D. H.↗