Search NASA⌕ Search

SEARCH · Search NASA

Results for “3D PRINTING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

3D Printing of Functional Hydrogel Devices for Screenings of Membrane Permeability and Selectivity

Developing a fundamental understanding of the effects of varying ligand chemistries on mass transport rates is key to designing membranes with solute-specific selectivity. While permeation cells offer a robust method to characterize membrane performance, they are limited to assessing a single membrane chemistry or salt solution per test. As a result, investigating the effects of varying ligand chemistries on membrane performance can be a tedious process, involving both the preparation of multiple samples and numerous, time-consuming permeation tests. This study uses digital light processing (DLP) 3D printing to fabricate a millifluidic flow-based permeation device made from a hydrogel active ester network that can be easily functionalized with ion-selective ligands. Without the need for bonding or assembly steps, ligands can be introduced and tested in the permeation device by simply injecting a small volume of a ligand solution. Various salt concentrations and molecular species can be cycled through a single device by switching the solution feeding into the salt reservoir, thereby reducing the number of samples needed for permeability and selectivity screenings. This research sets the groundwork for formulation development and postprocessing methods to 3D-print functional millifluidic devices capable of assessing solute selectivity in membranes and polymer adsorbents for aqueous separations. In this work, comparable salt permeability trends were observed with both 3D-printed devices and traditional assays. Devices were functionalized with an imidazole ligand to investigate salt permeability and selectivity of monovalent and divalent salts. Measurements showed increasing permeability for monovalent salts (NaCl) relative to divalent salts (MgCl 2 , CuCl 2 ) in functionalized membranes, with higher monovalent/divalent selectivity at increasing imidazole grafting densities. Here, the methods and findings described here represent a step toward developing higher-throughput methods with 3D-printed devices for screening the effects of ligand chemistry on mass transport rates in membrane materials.

36 MATERIALS SCIENCE↗

Efficient Hydrogen Delivery for Microbial Electrosynthesis via 3D-Printed Cathodes

The efficient delivery of electrochemically in situ produced H 2 can be a key advantage of microbial electrosynthesis over traditional gas fermentation. However, the technical details of how to supply large amounts of electric current per volume in a biocompatible manner remain unresolved. Here, we explored for the first time the flexibility of complex 3D-printed custom electrodes to fine tune H 2 delivery during microbial electrosynthesis. Using a model system for H 2 -mediated electromethanogenesis comprised of 3D fabricated carbon aerogel cathodes plated with nickel-molybdenum and Methanococcus maripaludis, we showed that novel 3D-printed cathodes facilitated sustained and efficient electromethanogenesis from electricity and CO 2 at an unprecedented volumetric production rate of 2.2 L CH4 /L catholyte /day and at a coulombic efficiency of 99%. Importantly, our experiments revealed that the efficiency of this process strongly depends on the current density. At identical total current supplied, larger surface area cathodes enabled higher methane production and minimized escape of H 2 . Specifically, low current density (<1 mA/cm 2 ) enabled by high surface area cathodes was found to be critical for fast start-up times of the microbial culture, stable steady state performance, and high coulombic efficiencies. Our data demonstrate that 3D-printing of electrodes presents a promising design tool to mitigate effects of bubble formation and local pH gradients within the boundary layer and, thus, resolve key critical limitations for in situ electron delivery in microbial electrosynthesis.

03 NATURAL GAS↗

Mechanically and Thermally Enhanced 3D-Printed Photocurable Polymer Nanocomposites Containing Functionalized Chitin Nanowhiskers by Stereolithography

Additive manufacturing, or simply 3D printing (3DP), where objects are built through layer-wise material deposition, has gained significant academic and industrial attention as a result of the development of advanced and functional materials requiring rapid, customized, and flexible solutions. In the context of green manufacturing, diversifying environmentally and economically sustainable material portfolios is an essential endeavor for the success of 3DP technology that uses widely available, highly valuable, and renewable materials. Here, we used stereolithography (SLA) for processing methacrylate-based photocurable resins containing crab shell-derived chitin nanowhiskers (CNWs), which are surface-functionalized by reactive acrylate groups. Results from full spectral, thermal, structural, and topological analyses corroborate not only the surface functionalization of CNWs but also indicate the presence of these photocurable CNW (pCNW) fillers in the 3D-printed nanocomposites. Owing to the strong interfacial bond induced by the physical and chemical crosslinking between the pCNW and methacrylate (MA) polymer matrix, the internally formulated nanocomposites displayed enhanced thermomechanical properties (e.g., storage modulus and glass transition temperature) compared to those of commercially available pure SLA resins. For instance, the inclusion of 0.5 wt % pCNW improved the tensile strength and stiffness to up to 78 and 71%, respectively, without compromising the toughness and ductility of the printed material. Accordingly, this result also evidences the compatibility between the filler and resin materials. Consequently, the formation of a crosslinked network in the nanocomposite structure results in a higher thermal stability and activation energy (i.e., up to ~79%) for all the hybrid materials than the pristine MA. Finally, the high-resolution SLA print features, dimensional accuracy, and enhanced mechanical performance of our microstructure-forming functionalized chitin-based nanocomposites make them promising materials for a wide range of robust and high-performance industrial applications.

36 MATERIALS SCIENCE↗

SU-F-E-13: Design and Fabrication of Gynacological Brachytherapy Shielding & Non Shielding Applicators Using Indigenously Developed 3D Printing Machine

Purpose: In this innovative work we have developed Gynecological Brachytherapy shielding & Non Shielding Applicators and compared with the commercially available applicators by using the indigenously developed 3D Printing machine. Methods: We have successfully indigenously developed the 3D printing machine. Which contain the 3 dimensional motion platform, Heater unit, base plate, ect… To fabricate the Gynecological Brachytherapy shielding & non shielding applicators the 3D design were developed in the computer as virtual design. This virtual design is made in a CAD computer file using a 3D modeling program. Separate programme for the shielding & non shielding applicators. We have also provided the extra catheter insert provision in the applicator for the multiple catheter. The DICOM file of the applicator were then converted to stereo Lithography file for the 3D printer. The shielding & Non Shielding Applicators were printed on a indigenously developed 3D printer material. The same dimensions were used to develop the applicators in the acrylic material also for the comparative study. A CT scan was performed to establish an infill-density calibration curve as well as characterize the quality of the print such as uniformity and the infill pattern. To commission the process, basic CT and dose properties of the printing materials were measured in photon beams and compared against water and soft tissue. Applicator were then scanned to confirm the placement of multiple catheter position. Finally dose distributions with rescanned CTs were compared with those computer-generated applicators. Results: The doses measured from the ion Chamber and X-Omat film test were within 2%. The shielded applicator reduce the rectal dose comparatively with the non shielded applicator. Conclusion: As of submission 3 unique cylinders have been designed, printed, and tested dosimetrically. A standardizable workflow for commissioning custom 3D printed applicators was codified and will be reported.

60 APPLIED LIFE SCIENCES↗

Thermomechanical properties of stereolithographic 3D-printed zinc oxide nanocomposites

Stereolithography (SLA) is a highly versatile additive manufacturing technique that utilizes various ink formulations to fabricate 3D-printed nanocomposite structures with desired properties. Zinc oxide (ZnO) is a promising candidate due to its excellent mechanical and thermal stability, and compatibility with various polymeric matrices. Here, in this work, varying ink formulations containing ZnO nanoparticles, along with employing appropriate post-printing curing parameters to fabricate SLA 3D-printed acrylate-based nanocomposites with improved mechanical and thermal properties, were reported. This study can significantly contribute to expanding its potential use in practical applications such as biomedical and structural applications.

36 MATERIALS SCIENCE↗

Tensile properties of 3D-printed wood-filled PLA materials using poplar trees

Fabrication of renewable materials through additive manufacturing using wood-filled polylactic acid (PLA) is an emerging field of study. The variability in the tensile properties of 3D-printed materials due to the variability in woody biomass properties has not been studied. Biomass size reduction, filament extrusion, and 3D-printing methods were investigated to determine the conditions that resulted in consistent printing. Using 20% ball-milled poplar reinforcement in PLA, 210 °C filament extrusion temperature and 230 °C printing temperature were found to be the best conditions. Subsequently, seventy poplar samples from a common garden were used to test the tensile properties of the printed materials. The median tensile strength at yield was 50 MPa, with 5–95 percentiles ranged in 37–54 MPa. Strain% at break had a median value of 2.1%, and 5–95 percentiles were 1.7–2.7%. The median Young's modulus was 3.65 GPa, and 5–95 percentiles ranged in 2.9–4.1 GPa. Biomass density was correlated to composite density. Median particle size of ball-milled poplar was negatively correlated with tensile strength. Composite density affected tensile strength of the composite. β-glycosidic bond of polysaccharides in biomass affected Young's modulus of the composite. Overall, these data show that genotypic variation among Populus trichocarpa have substantial effect on tensile properties of 3D printed PLA-poplar materials.

36 MATERIALS SCIENCE↗

Effect of 3D-printed surface textures on wear mechanism in 3-body abrasion of soil

This study systematically investigates the enhancement of wear resistance in 3D printed surface textures through both experimental and theoretical approaches. Three distinct surface morphologies (Smooth Surface, Surface with uniformly distributed Pits, and Surface with uniformly distributed Bumps) were fabricated using High-Impact Polystyrene, where the meso-scale textures were precisely controlled through the 3D printing process. Wear behavior was evaluated using a 3-body wear tester in an abrasive particle environment, analyzing the influence of surface textures under various operating conditions. Systematic wear tests revealed that optimally designed surface textures achieved a remarkable 77 % reduction in wear compared to the worst-performing sample. The wear mechanisms were comprehensively characterized through weight loss measurements, Scanning Electron Microscopy (SEM), and Energy Dispersive Spectroscopy (EDS) analyses, elucidating the surface morphology changes and their interaction with wear particles. Notably, the study identified how the geometric characteristics of surface textures influence the movement of wear particles and the distribution of contact stresses. Discrete element method simulations corroborated the experimental findings, providing theoretical validation for the enhanced wear resistance of the optimal structure. The high correlation between simulated wear patterns and experimental results validates the reliability of the proposed design methodology. In conclusion, these results demonstrate that 3D printed surface texturing offers a cost-effective and scalable approach to significantly improve wear resistance in engineering applications, presenting a practical alternative to conventional, high-cost surface engineering methods.

3-body abrasion↗

Performance of Embedded Sensors in 3D Printed SiC

This report summarizes recent advances in embedding sensors in 3D printed silicon carbide (SiC) ceramic components under the Transformational Challenge Reactor (TCR) program. The additive manufacturing technologies developed under this program will enable fabrication of complex structures with embedded fuels and sensors. The sensors will be capable of characterizing fuel performance using spatially distributed measurements at the most strategic locations that would be otherwise inaccessible using conventional manufacturing techniques. While previous programmatic updates describe initial concepts for embedding sensors, materials selection, and initial characterization of the embedded sensors, the technology requires further demonstration, and quality-significant procedures must be established before the embedding technology is ready for adoption by industry. To this end, this report describes the most effective techniques that have been used to embed functional sensors in 3D printed components using a combination of binder-jet additive manufacturing and chemical vapor infiltration (CVI). A detailed procedure describes each step in the process and is available upon request. Molybdenum (Mo)-sheathed thermocouples have been successfully embedded in complex SiC components, and temperatures were monitored in situ during the embedding process. Post-embedding measurements showed no significant hysteresis, and characterization of the interface revealed qualitatively strong bonding around the entire perimeter of the sensor sheath. Distributed fiber-optic temperature sensors were able to briefly measure temperature profiles during CVI, but they ultimately failed prior to completion of the CVI run. The failure appears to be related to the fiber coating at temperatures close to 1,000°C. Future work will focus on irradiation testing of embedded thermocouples and other sheathed electrical sensors, as well as the identification of fiber-optic sensor coatings that can survive CVI.

42 ENGINEERING↗

Investigating the accuracy of microstereotactic-body-radiotherapy utilizing anatomically accurate 3D printed rodent-morphic dosimeters

Purpose: Sophisticated small animal irradiators, incorporating cone-beam-CT image-guidance, have recently been developed which enable exploration of the efficacy of advanced radiation treatments in the preclinical setting. Microstereotactic-body-radiation-therapy (microSBRT) is one technique of interest, utilizing field sizes in the range of 1–15 mm. Verification of the accuracy of microSBRT treatment delivery is challenging due to the lack of available methods to comprehensively measure dose distributions in representative phantoms with sufficiently high spatial resolution and in 3 dimensions (3D). This work introduces a potential solution in the form of anatomically accurate rodent-morphic 3D dosimeters compatible with ultrahigh resolution (0.3 mm{sup 3}) optical computed tomography (optical-CT) dose read-out. Methods: Rodent-morphic dosimeters were produced by 3D-printing molds of rodent anatomy directly from contours defined on x-ray CT data sets of rats and mice, and using these molds to create tissue-equivalent radiochromic 3D dosimeters from Presage. Anatomically accurate spines were incorporated into some dosimeters, by first 3D printing the spine mold, then forming a high-Z bone equivalent spine insert. This spine insert was then set inside the tissue equivalent body mold. The high-Z spinal insert enabled representative cone-beam CT IGRT targeting. On irradiation, a linear radiochromic change in optical-density occurs in the dosimeter, which is proportional to absorbed dose, and was read out using optical-CT in high-resolution (0.5 mm isotropic voxels). Optical-CT data were converted to absolute dose in two ways: (i) using a calibration curve derived from other Presage dosimeters from the same batch, and (ii) by independent measurement of calibrated dose at a point using a novel detector comprised of a yttrium oxide based nanocrystalline scintillator, with a submillimeter active length. A microSBRT spinal treatment was delivered consisting of a 180° continuous arc at 225 kVp with a 20 × 10 mm field size. Dose response was evaluated using both the Presage/optical-CT 3D dosimetry system described above, and independent verification in select planes using EBT2 radiochromic film placed inside rodent-morphic dosimeters that had been sectioned in half. Results: Rodent-morphic 3D dosimeters were successfully produced from Presage radiochromic material by utilizing 3D printed molds of rat CT contours. The dosimeters were found to be compatible with optical-CT dose readout in high-resolution 3D (0.5 mm isotropic voxels) with minimal artifacts or noise. Cone-beam CT image guidance was possible with these dosimeters due to sufficient contrast between high-Z spinal inserts and tissue equivalent Presage material (CNR ∼10 on CBCT images). Dose at isocenter measured with optical-CT was found to agree with nanoscintillator measurement to within 2.8%. Maximum dose in line profiles taken through Presage and film dose slices agreed within 3%, with FWHM measurements through each profile found to agree within 2%. Conclusions: This work demonstrates the feasibility of using 3D printing technology to make anatomically accurate Presage rodent-morphic dosimeters incorporating spinal-mimicking inserts. High quality optical-CT 3D dosimetry is feasible on these dosimeters, despite the irregular surfaces and implanted inserts. The ability to measure dose distributions in anatomically accurate phantoms represents a powerful useful additional verification tool for preclinical microSBRT.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

What makes a material printable? A viscoelastic model for extrusion-based 3D printing of polymers

This paper presents a practical model for evaluating polymer feedstock materials as candidates for 3D printing across a variety of extrusion-based platforms. In order for a material to be successfully utilized for 3D printing operations, a series of fundamental conditions must be met. First, pressure-driven extrusion must occur through a given diameter nozzle at a specified flow rate. Second, the extruded material must form and sustain the desired shape. Third, the extruded structure must be able to bridge a specified gap and serve as a mechanically sound foundation for successive deposits. Finally, the deposited structure must be dimensionally stable during the transition to the final state (i.e. fully cured at room temperature). This article presents a framework for extrusion-based printing and a simple viscoelastic model for each of these conditions based on the rheological and thermo-physical properties of the candidate material and the processing parameters of the extrusion-based deposition platform. The model is demonstrated to be a useful tool for the evaluation of example test cases including: high temperature thermoplastics (polyphenylsulfone), fiber reinforced thermoplastics (acrylonitrile butadiene styrene), low-viscosity thermosets (epoxy resins), and thermoplastics with a high coefficient of thermal expansion (polypropylene).

36 MATERIALS SCIENCE↗

NASA's Centennial Challenge for 3D-Printed Habitat: Phase II Outcomes and Phase III Competition Overview

The 3D-Printed Habitat Challenge is part of NASA's Centennial Challenges Program. NASA's Centennial Challenges seek to accelerate innovation in aerospace technology development through public competitions. The 3D-Printed Habitat Challenge, launched in 2015, is part of the Centennial Challenges portfolio and focuses on habitat design and development of large-scale additive construction systems capable of fabricating structures from in situ materials and/or mission recyclables. The challenge is a partnership between NASA, Caterpillar (primary sponsor), Bechtel, Brick and Mortar Ventures, and Bradley University. Phase I of the challenge was an architectural concept competition in which participants generated conceptual renderings of habitats on Mars which could be constructed using locally available resources. Phase II asked teams to develop the printing systems and material formulations needed to translate these designs into reality. Work under the phase II competition, which concluded in August 2017 with a head to head competition at Caterpillar's Edward Demonstration Facility in Peoria, Illinois, is discussed, including the key technology development outcomes resulting from this portion of the competition. The phase III competition consists of both virtual and construction subcompetitions. Virtual construction asks teams to render high fidelity architectural models of a habitat and all the accompanying information required for construction of the pressure retaining and load bearing portions of the structure. In construction phase III, teams are asked to scale up their printing systems to produce a 1/3 scale habitat on-site at Caterpillar. The levels of the phase III construction competition (which include printing of a foundation and printing and hydrostatic testing of a habitat element) are discussed. Phase III construction also has an increased focus on autonomy, as these systems are envisioned for robotic precursor missions which would buildup infrastructure prior to the arrival of crew. Results of the phase III competition through July 2017 (which includes virtual construction level 1) are discussed. This Centennial Challenge enables an assessment of the scaleability and efficacy of various processes, material systems, and designs for planetary construction. There are also near-term terrestrial applications, from disaster response to affordable housing and infrastructure refurbishment, for these technologies.

Prater, T. J.↗

Characterization of Properties of Laser Powder Bed Fusion 3D-Printed Inconel 718 for Centrifugal Turbomachinery Applications

Here, this paper presents the results of a comprehensive effort to characterize the properties of Inconel 718 produced by a form of laser powder bed fusion (LPBF) additive manufacturing (AM) or 3D-printing, subsequently subjected to hot isostatic pressing (HIP) and heat treatment according to standards F3055-14a and AMS 5663, respectively. Material property data, while broadly available for traditional Inconel 718 presentations (e.g. forgings or castings), is currently lacking for the 3D-printed material. It is expected that while limited in size, the experimental data sets presented provide sufficient information to glean the capability of LPBF Inconel 718. These include: 1) Chemical composition, electron backscatter diffraction (EBSD), and x-ray energy dispersive spectroscopy (XEDS) characterization of 3D-printed material structure; 2) Tensile properties — 0.2% yield stress, ultimate stress, modulus of elasticity, and elongation to failure — based on 108 samples, as functions of temperature and sample print orientation; 3) Creep rupture data including the Larson-Miller parameter, based on 21 samples; and 4) High cycle fatigue data based on 21 samples as a function of temperature. Results are compared to available standards and/or data for forged, cast, and other AM Inconel 718. A key observation of this study, based on the EBSD results, is that while the material appears to approach full recrystallization following heat treatment, there is a detectable fraction of the material that does not fully recrystallize, resulting in a material with mechanical properties (e.g. yield stress, creep rupture) measurably lower than those of forgings, but higher than those of castings.

30 DIRECT ENERGY CONVERSION↗

SIBatt-3D: In-Space/On-Surface 3D Printing of Sodium Ion Batteries from ISRU Materials

Constructed more than 20 years ago, the International Space Station’s primary power system originally used nickel-hydrogen batteries with a lifetime of 6.5 years, until NASA began the process of replacing them in 2016 with lithium-ion batteries with a lifetime of 10 years. The demanding and costly process was accomplished after four flights of the Japanese H-II Transfer Vehicle cargo spacecraft (with a cost of about $10,000 per pound of payload), and 13 different astronauts conducting 14 spacewalks. Besides utilization in the ISS, rechargeable batteries are present in many space applications: they are installed in exploration robots, life support systems and in portable communication devices, to mention some. In this context, this project is focused on the in-space manufacturing of shape-conformable batteries using in-situ resources, and aims to address the NASA’s gaps related to the development of next generation of energy storage devices (TX03), as well as in-space manufacturing and in-situ resource utilization (TX07). The proposed work also tackles the HEOMD’s objectives targeting the in-space additive manufacturing (AM) from Lunar/Martian materials (regolith as AM feedstock) to reinvigorate America’s Human Space Exploration Program (SPD-1). This project is in direct alignment with the STMD’s objectives to demonstrate in-space autonomous manufacturing and assembly of complete systems by 2030, and to enable humans to live and explore in space and on planetary surfaces by 2040 thanks to in-space habitation, infrastructure development and in-situ resource utilization (ST1 and ST5). Manufacturing of shape conformable batteries directly in-space and using in-situ resources would also contribute to reducing the payload weight and volume (TX12) for future missions, thus reducing risk for long term Mars missions where rapid resupply is logistically infeasible. Nowadays, commercial batteries consist of stacked two-dimensional (2D) sheets, which are only manufactured in restricted geometries (cylindrical and coin cell). Evolving from conventional 2D, complex 3D battery architectures have been proven to increase the electrochemical active surface area and ion diffusion path, leading to improved areal energy density and power performance. This tendency was illustrated in our recent in-depth modeling studies by simulating a classical Ragone plot exhibiting the energy-power relationship. Our team demonstrated through modeling that a complex gyroidal 3D printed battery architecture exhibits significantly improved power performances (>150% at the current density of 6C; full discharge in 10 minutes) in comparison to a traditional 3D printed planar geometry. Motivated by these results and as the fabrication of intricate 3D battery design is only possible experimentally thanks to the geometric freedom offered by additive manufacturing (AM), our team has already initiated leveraging thermoplastic material extrusion at the laboratory scale. While 3D printing of batteries is relatively recent (2013), it has witnessed a growing interest during the last recent years, as next-generation shape-conformable 3D batteries can be co-designed with the system. Consequently, dead-volume and mass brought from Earth are minimized, in addition to improved battery performance, in alignment with the aforementioned NASA’s objectives. Further, while this project is specifically dedicated to batteries, it lends itself towards the maturation of in-space manufacturing via 3D printing using in-situ resources, stated in HEOMD and STMD goals.

In-Space Manufacturing↗

Characterization of radiation damage in 3D printed SiC

The SiC fuel matrix for advanced gas-cooled high temperature reactors as part of the Transformational Challenge Reactor program serves as the fuel particle container structure, a barrier to fission gas release, and a heat transfer medium. Its performance is particularly important because the fuel matrix must demonstrate good structural stability and thermal behaviors. An additive manufacturing methodology combining a binder jet 3D printing process with chemical vapor infiltration (CVI) for the production of SiC was recently developed. In this study, post irradiation examination by transmission electron microscopy shows that defect accumulation within the printed particles is very similar to other forms of high-purity SiC. However, damage accumulation was not directly observed in the CVI matrix because black spot damage and dislocation loops are difficult to image within the nanoscale highly faulted CVI matrix and because interstitial defects may rapidly annihilate at the stacking faults. Therefore, electron energy loss spectroscopy (EELS) analysis was used to analyze defect swelling in both the printed particles and the CVI matrix. The EELS analysis helped reveal that the radiation-induced swelling in the CVI matrix is similar to that of the printed SiC particles. This work shows that 3D printed SiC has behavior that is comparable to SiC processed by other means and that 3D printing could serve as a suitable processing technique for high-purity SiC for nuclear applications.

36 MATERIALS SCIENCE↗

30-kW All-SiC Inverter with 3D-Printed Air-Cooled Heatsinks for Plug-In and Full Electric Vehicle Applications

This paper presents the design and development of a 30-kW 3D printed based air-cooled silicon carbide (SiC) inverter for electric vehicle application. Specifically, an all-SiC air-cooled power module is designed, aiming at reduced thermal resistance for high temperature and high power density operation. The module assembly incorporates three major parts: an optimized 3D printed heat sink, a SiC MOSFET phase leg module, and a two-channel gate driver. The electrical and thermal performance of the power module is evaluated through double pulse test and continuous operation. Based on the air-cooled power module, a three-phase half-bridge voltage source inverter with 3D-printed air duct is built and tested to further verify the performance of the power module.

33 ADVANCED PROPULSION SYSTEMS↗

Simulation of Endovascular Aortic Repair Using 3D Printed Abdominal Aortic Aneurysm Model and Fluid Pump

Background: Abdominal aortic aneurysm (AAA) models can be manufactured with 3D printing technology. This study describes detailed methodology and validation of endovascular aortic repair (EVAR) simulation using 3D printed AAA model connected to hemodynamic pump. Method: The AAA model was printed with Objet500 Connex3 (Stratasys, Eden Prairie, MN) and connected to BDC PD-0500 fluid pump (BDC Laboratories, Wheat Ridge, CO). EVAR procedure metrics were benchmarked in two expert implanters and compared to 20 vascular surgical trainees with different levels of EVAR experience (< 20 or ≥ 20 cases). All simulations were performed using commercially available stent grafts, guidewires, catheters, fluoroscopic guidance and digital subtraction angiography. Studied outcomes included ability to complete the procedure independently, time to deploy aortic component, ability to cannulate contralateral gate and complete the repair, and total fluoroscopy and procedure times. Results: A total of 22 EVAR simulation procedures were performed with mean procedure time of 37 ± 12 min. Experienced trainees had significantly lower total procedural time (32 ± 9 vs. 44 ± 6 min, P = 0.003) and fluoroscopic time (13 ± 5 vs. 23 ± 8 min, P = 0.005). All experienced trainees completed the procedure independently in < 45 min, compared to six (46%) of those with less EVAR experience (P = 0.016). Among less experienced trainees, only two (15%) completed the entire procedure independently (P < 0.001). Benchmark implanters performed significantly better than both trainee groups in nearly all EVAR metrics. Conclusion: EVAR simulation was feasible and simulated all procedural steps with high fidelity. This model may be applicable for assessment of technical competencies and standard endovascular skill acquisition within vascular surgery training curricula.

3D PRINTING↗

SU-F-T-181: Proton Therapy Tissue-Equivalence of 3D Printed Materials

Purpose: This work investigated the proton tissue-equivalence of various 3D printed materials. Methods: Three 3D printers were used to create 5 cm cubic phantoms made of different plastics with varying percentages of infill. White resin, polylactic acid (PLA), and NinjaFlex plastics were used. The infills ranged from 15% to 100%. Each phantom was scanned with a CT scanner to obtain the HU value. The relative linear stopping power (RLSP) was then determined using a multi-layer ion chamber in a 200 MeV proton beam. The RLSP was measured both parallel and perpendicular to the print direction for each material. Results: The HU values of the materials ranged from lung-equivalent (−820 HU σ160) when using a low infill, to soft-tissue-equivalent 159 (σ12). The RLSP of the materials depended on the orientation of the beam relative to the print direction. When the proton beam was parallel to the print direction, the RLSP was generally higher than the RLSP in the perpendicular orientation, by up to 45%. This difference was smaller (less than 6%) for the materials with 100% infill. For low infill cubes irradiated parallel to the print direction, the SOBP curve showed extreme degradation of the beam in the distal region. The materials with 15–25% infill had wide-ranging agreement with a clinical HU-RLSP conversion curve, with some measurements falling within 1% of the curve and others deviating up to 45%. The materials with 100% infill all fell within 7% of the curve. Conclusion: While some materials tested fall within 1% of a clinical HU-RLSP curve, caution should be taken when using 3D printed materials with proton therapy, as the orientation of the beam relative to the print direction can result in a large change in RLSP. Further investigation is needed to measure how the infill pattern affects the material RLSP. This work was supported by PHS grant CA180803.

60 APPLIED LIFE SCIENCES↗