Search NASA⌕ Search

SEARCH · Search NASA

Results for “ABRASIVES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

Pile Fuel Cladding Silo Deflector Plate Removal Project Using Long Reach Tooling and Suspended Abrasive Water Jet Cutting System - 17541

The Pile Fuel Cladding Silo (PFCS) at the Sellafield decommissioning, reprocessing and nuclear waste management facility in the UK was constructed in the late 1940-s and used for the storage of Intermediate Level Waste (ILW) arising from the Windscale Piles, Calderhall and Chapelcross Reactors until the 1960's. The PFCS is 21 metres high and comprises 6 identical tall compartments with the waste added to the silo via a charge-hole at the top of each compartment; each compartment is split by a central dividing wall that runs from the base of the silo to a few metres below the underside of the silo roof. A deflector plate assembly (DPA) supported on two horizontal beams is located between the top of the dividing wall and the roof and allowed the waste to spread as it fell into the silo and prevent excessive mounding. Sellafield Ltd is currently engaged in an overall programme of works to remove the waste for storage within modern ILW containers. Prior to the commencement of these works the Deflector Plate Assemblies (DPA) and beam structures within the silos are required to be removed to allow access for the waste retrievals equipment through the side of the silo at the point where the DPAs are situated. James Fisher Nuclear (JFN) and Sellafield Ltd have developed a system using suspended water jet cutting equipment combined with custom long reach tooling, installed through penetrations made in the side of the silo, to enable the remote size reduction of the DPA and beams within each compartment. The use of a low pressure suspended water jet cutting system has enabled a single water/abrasive hose to be routed down a tool deployment pole and allowed long hose lengths up to 80 m from pump to nozzle enabling siting of equipment on a congested and difficult access site. The use of lightweight, yet high strength, carbon fibre poles within the tools has enabled the deployment of tool end effectors at distances of up to 6.5 m from the compartment walls using a relatively small 60 mm diameter pole. This maximised articulation of the pole within the 300 mm wall penetrations to reach all areas of the DPA. Capability of the operators to install the tooling and size reduce DPA and beam assemblies have been demonstrated through the training on a Full Scale Test Rig (FSTR). The FSTR was integral to the development of the equipment and techniques and to providing assurance to the client that the project was technically achievable given the tight building restraints and safety issues. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Molecular dynamics simulation of self-rotation effects on ultra-precision polishing of single-crystal copper

Understanding the behaviors of the material removal mechanism of ultra-precision polishing process has been a critical issue of generating well-formed surface. In order to make clear the abrasive self-rotation effects on material removal at the atomic level, a three-dimensional molecular dynamics (MD) model is conducted to study the mechanics of ultra-precision polishing on single-crystal copper with a diamond abrasive and the effects of abrasive self-rotation velocity and direction. Morse potential energy function and EAM potential energy function are applied to model the copper/diamond and copper/copper interactions, respectively. The simulation results show that the deformation mechanism of single-crystal copper is due to the formation and movement of dislocations in the specimen. In addition, with the increasing of abrasive self-rotation velocity, the deformation mechanism falls from cutting to plowing regimes. The abrasive self-rotation velocity and direction have effects on the morphology and quality of the specimen surface, distribution and evolution of defects under the surface of the specimen. Also, the interatomic force between abrasive and specimen is studied to account for the effects of different polishing conditions.

36 MATERIALS SCIENCE↗

Tribological Properties of the Oxide Coatings Produced onto 6061-T6 Aluminum Alloy in the Hard Anodizing Process

The aim of this work was to establish the influence of the thickness of the anodic coatings on their mechanical properties and to understand the relation between their hardness and the abrasion resistance. The coatings were produced in the hard anodizing process onto the 6061-T6 aluminum alloy. Their thickness was in the range between 19 and 43 µm. The abrasion resistance was determined by using Taber abrasion test. The weight losses of the coatings obtained were in the range between 15 and 11 mg and decreased with their increasing thickness. It has been shown that the hardness measured on the cross sections of the coatings did not correspond to their abrasion resistance. Thus, the new approach has been proposed. The hardness of the coatings was estimated on the basis of the results of the scratch test performed at the constant load. The results obtained correspond to the abrasion resistance of the coatings.

36 MATERIALS SCIENCE↗

Erosion Experimentation in Solar Power Systems

An alternate and sustainable form of energy is concentrated solar power (CSP) systems, which capture and store the sun’s energy in the form of heat. To increase the efficiency and overall cost of the plant, particles were used as a heat transfer medium. As particles flow through this system, the movement of particles creates erosion, in the forms of abrasion and attrition. Experiments were tested at room temperature and 800 degrees Celsius for both abrasion wear and attrition erosion. In abrasion wear, specimens were placed inside a container, particles were added, and the specimen rotated in and out of the particles. In attrition erosion, a steel disk rotated amongst particles which resulted in particles rubbing against each other. Abrasion wear increased when temperature increased while attrition showed that the particles broke down as the amount of time increased. For attrition at 800 degrees Celsius, oxide was increased and mixed with the particles. Durability models will be created to predict attrition and abrasion based on the particle and specimen mechanical properties. This discovery shows that this method of utilizing particles for CSP plants would improve efficiency and decrease overall costs.

14 SOLAR ENERGY↗

Towards predicting removal rate and surface roughness during grinding of optical materials

A series of controlled grinding experiments, utilizing loose or fixed abrasives of either alumina or diamond at various particle sizes, were performed on a wide range of optical workpiece materials [single crystals of Al 2 O 3 (sapphire), SiC, Y 3 Al 5 O 12 (YAG), CaF 2 , and LiB 3 O 5 (LBO); a SiO 2 -Al 2 O 3 -P 2 O 5 -Li 2 O glass ceramic (Zerodur); and glasses of SiO 2 :TiO 2 (ULE), SiO 2 (fused silica), and P 2 O 5 -Al 2 O 3 -K 2 O-BaO (Phosphate)]. The material removal rate, surface roughness, and the morphology of surface fractures were measured. Separately, Vickers indentation was performed on the workpieces, and the depths of various crack types as a function of applied load was measured. Single pass grinding experiments showed distinct differences in the spatial pattern of surface fracturing between the loose alumina abrasive (isolated indent-type lateral cracking) and the loose or fixed diamond abrasive (scratch-type elongated lateral cracking). Each of the grinding methods had a removal rate and roughness that scaled with the lateral crack slope, sℓ (i.e. the rate of increase in lateral crack depth with the applied load) of the workpiece material. A grinding model (based on the volumetric removal of lateral cracks accounting for neighboring lateral crack removal efficiency and the fraction of abrasive particles leading to fracture initiation) and a roughness model (based on the depth of lateral cracks or the interface gap between the workpiece and lap) are shown to quantitatively describe the material removal rate and roughness as a function of workpiece material, abrasive size, applied pressure and relative velocity. This broad, multi-process variable grinding model can serve as a predictive tool for estimating grinding rates and surface roughness for various grinding processes on different workpiece materials

36 MATERIALS SCIENCE↗

Subsurface mechanical damage of fused silica glass during grinding by various sub-aperture tools with and without ultrasonics

The subsurface mechanical damage (SSD) depth after grinding fused silica glass with a comprehensive set of sub-aperture fixed abrasive grinding tools [cup, wheel, belt, pad, and rotary face mill (with and without ultrasonics)] and process parameters has been statistically measured using the taper wedge technique and evaluated. Consistent with a previously reported grinding model [J. Non-Cryst. Solids 352, 5601–5617 (2006) Crossref , Materials Science and Technology of Optical Fabrication (Wiley & Sons, 2018)], based on the sliding indentation fracture by sliding particles or asperities where the normal load per particle determines the depth of the fracture (and ultimately the overall SSD depth), the dominant factor controlling SSD depth was found to be the abrasive size regardless of the tool type and process conditions. Compared to full aperture grinding methods, the overall SSD depth was higher using the sub-aperture tools, likely due to the higher effective pressure and higher load per particle distribution. Here, in addition to abrasive size, a significant reduction in SSD depth was achieved by: (1) reducing the load distribution on the abrasive particles via increase in contact area and/or decrease in mechanical loading; (2) using a more compliant host tool medium; and (3) in what we believe is a more novel way, using ultrasonics. Combining low abrasive size, larger contact area, and a compliant host, the 6 µm diamond in a resin matrix (Trizact) on a foam pad led to very low SSD depth (~ 4.6 µm), relatively fast grinding rate (186 mm 3 /h), and little or no figure degradation. This grinding tool/process is an attractive choice for final grind, resulting in significantly reduced polish out (i.e., “grey out”) times. With the rotary face mill tool, the use of ultrasonics consistently led to a SSD depth reduction (ranging from 17%–34%). A new fracture mechanics-based model, to the best of our knowledge, where the relevant normal load is parallel to the feed direction, has been developed to explain how ultrasonics leads to lower SSD depth. The key factors, supported by finite element stress analysis and load measurements, are (1) the initiation of fractures at higher z heights during the tool’s ultrasonic vertical oscillations, thus propagating less deep into workpiece; (2) reduction in load (and therefore reduction in fracture propagation distance) due to smaller tool-workpiece feed direction contact area (again caused by higher heights relative to depth of cut); (3) upward movement of the tool during oscillation leads to fracturing toward the surface instead into the depth; and finally (4) at tool’s lowest point of oscillation cycle, there may not be enough time for the fracture to propagate to its full length.

Optics and optical instruments↗

The XPS depth profiling and tribological characterization of ion-plated gold on various metals

Friction properties were measured with a gold film; the graded interface between gold and nickel substrate; and the nickel substrate. All sliding was conducted against hard silicon carbide pins in two processes. In the adhesive process, friction arises primarily from adhesion between sliding surfaces. In the abrasion process, friction occurs as a result of the hard pin sliding against the film, indenting into it, and plowing a series of grooves. Copper and 440 C stainless steel substrates were also used. Results indicate that the friction related to both adhesion and abrasion is influenced by coating depth. The trends in friction behavior as a function of film depth are, however, just the opposite. The graded interface exhibited the highest adhesion and friction, while the graded interface resulted in the lowest abrasion and friction. The coefficient of friction due to abrasion is inversely related to the hardness. The greater the hardness of the surface, the lower is the abrasion and friction. The microhardness in the graded interface exhibited the highest hardness due to an alloy hardening effect. Almost no graded interface between the vapor-deposited gold film and the substrates was detected.

Miyoshi, K.↗

Erosion and transport of eolian materials on Mars

An abrasion chamber was constructed to produce grain to grain impacts and to eliminate, as far as possible, grain to wall impact. Quartz, basalt, olivine, and volcanic ash were used as abrasives to determine particle longevity on Mars during eolian abrasion. The various abrasion velocities, measured velocity or particles, calculated velocity of collision, time during which abrasion took place, the charge (material) in grams, and the percent remaining after completion are tabulated. The tests show that if coarse sand-sized particles of the composition presumably present on Mars are moved at the wind velocities given, almost complete destruction can occur in geologically insignificant time periods. Grain to rock collisions are not necessary for almost complete destruction; grain to grain collisions are sufficient.

Krinsley, D.↗

Assessing Organic Preservation and the Implications for Potential Biosignatures in the Bastide Member of the Séítah Formation, Jezero Crater

Introduction: Olivine has the highest CO2 trapping potential of ultramafic minerals, due to its rapid rate of dissolution and high percentage of divalent cations/unpolymerized silicate tetrahedra [1]. It generates divalent carbonates from CO2 and sequesters CO2 into the mineral matrix of the target lithology. The co-occurrence of olivine and carbonate within abraded targets from the Bastide Member of the Séítah Formation (Fm) of the Jezero crater floor [2] suggests the carbonation of olivine occurred within the mineral matrix hosted in a subsurface system. Hydrothermal origins for the subsurface system are hypothesized from orbital data [3]. This is supported by the detection of hydration features within the rock as well as the carbonate features are solely detected within the abrasion patch but not the rock’s surface. Organic preservation potential of abrasion patches: We incorporated the SHERLOC/WATSON results acquired from the Dourbes, Garde, and Quartier abrasion patches in the Séítah Fm to investigate the organomineral associations, and determine the biosignature preservation potential of these rocks. Dourbes is dominated by olivine and has minor amounts of carbonate, hydrated Ca-sulfate, and amorphous or microcrystalline silicate. Fluorescence features (330-340 nm) are detected in discrete locales and could be consistent with double ring aromatic organic molecules; yet, these features do not appear to be associated with an identified mineral phase. Dark subhedral to euhedral olivine grains within the Garde abrasion patch often co-occur with carbonate-consistent spectral signatures in all analyzed scans. The availability of Fe2+ is a known influence on olivine dissolution rates [1] and SuperCam estimates of the olivine composition (Forsterite-60 average for Sols 202-234) may thereby provide a constraint on the carbonation extent. Carbonated olivine phenocrysts within the matrix may be due to aqueous alteration, as the carbonation of nodules is consistent with observations in other hydrothermal systems and within Martian meteorites (ALH84001) [4]. In comparison, the Quartier abrasion patch represents an extensively altered endmember within the Bastide Member of the Séítah Fm. It contains a fluorescence doublet at 305/325 nm that coexists with multiple species of Na-sulfate and Mg-sulfate, Mg-carbonates, olivine [5]. Aqueous alteration and implications for habitability: The identification of primary and secondary mineral phases observed in the Bastide Member suggests the release of cations from primary ultramafic minerals through aqueous alteration. Within Garde, the carbonate detected appears to be Mg-rich and likely formed from the in situ alteration of Mg-rich olivine within the region as carbonate has only been detected within the rock via in situ analysis. Carbonates derived from abiotic and biotic reactions preserve biosignatures (i.e. indices of habitability) on Earth. The detected carbonate phase found in association with fluorescent features within the rock matrix may also indicate potential organic compounds preserved in a putative hydrothermal system. Fluorescent features (~330 nm) are unique to Garde and Dourbes, though they are co-located to carbonate signatures solely within Garde, and between the light toned minerals. Identification of these fluorescent features may be consistent with 1-2 ring aromatic compounds. The limit of detection for Raman is multiple orders of magnitude greater than the limit of detection required for fluorescence [6]. Implications for provenance: Hydrothermal systems represent disequilibrium chemical conditions that are hypothesized to have supported the emergence of life and also preserve ancient carbon within precipitated carbonates [7]. Hydrothermal system associated carbonates are capable of preserving biosignatures up to an estimated ~3.77 – 4.28 Gya [8]. Thus, carbonated olivine found within the Séítah Fm may represent a high-potential biosignature preserving environment on Mars. The formation of carbonates by an aqueous alteration process, such as carbonation of olivine is also consistent with hypotheses for carbonate within the greater regional-olivine bearing unit [2,3], which contains Garde, Dourbes, and Quartier. Acknowledgments: This work was carried out at the Jet Propulsion Laboratory, The California Institute of Technology under a contract from NASA. References: [1] Wood et al., (2019) ES&T, 6, 10. [2] Stack, K. et al., (2020) Space Sci Rev, 216, 127. [3] Tarnas, J. et al., (2021) JGR: Planets, 126, 11. [4] Steele et al., (2007) Meteorit. Planet. Sci., 42, 9. [5] Murphy, A.E. et al., (2022) LPSC [6] Bhartia et al., (2021) Space Sci Rev, 217, 58. [7] Luther (2021) GRL, 48, e2021GL094869. [8] Dodd et al., (2017) Nature, 543, 60-64

E L Cardarelli↗

Capture, disruption, and extraction apparatus and method

A cell capture, disruption, and extraction method includes a introducing a plurality of abrasives in a disruption chamber, which can include diamond powder, variably and multi dimensionally disbursed therein, and a pestle positioned in the disruption chamber. The method includes agitating the abrasives by moving the disruption chamber and/or pestle, agitation of the abrasives tearing cell structure in the solution to access its contents. A binding column or size exclusion column can be positioned downstream of the disruption chamber. Cell solution can first be introduced in the disruption chamber, the abrasives capturing the cells and allowing therethrough and purging the waste content, then breaking the cell content. The lysate can then bind to an extraction matrix downstream of the disruption chamber or it can be mixed in with the abrasives.

Peyvan, Kianoosh↗

Processing and Characterization of Fe-Mn-Cu-Sn-C Alloys Prepared by Ball Milling and Spark Plasma Sintering

In this work, Fe-Mn-Cu-Sn-C alloys were prepared by means of powder metallurgy (PM). Powder mixtures were ball-milled for 8, 30 and 120 h and densified to < 1% porosity using spark plasma sintering (SPS) at 900 °C and 35 MPa. After consolidation, all samples of the Fe alloys were characterized by x-ray diffraction (XRD), scanning electron microscopy (SEM), hardness and flexural strength tests. Resistance to abrasive wear was evaluated in both three-body abrasion and two-body abrasion tests. The SEM observations revealed an evident dependence of grain size and microstructural homogeneity on milling time. The XRD analysis showed a marked increase in austenite content in the as-sintered specimens with milling time. Although the proportion of deformation-induced martensite was small, the strengthening effect of abrasion on the subsurface layer of the investigated alloys was clearly indicated by Knoop hardness measurements.

36 MATERIALS SCIENCE↗

Al{sub 2}O{sub 3}-TiC Composite Prepared by Spark Plasma Sintering Process: Evaluation of Mechanical and Tribological Properties

Al{sub 2}O{sub 3}-10TiC composites were synthesized by spark plasma sintering (SPS) process. Microstructural and mechanical properties of the composite reveal homogeneous distribution of the fine TiC particles in the matrix. The samples were produced with different sintering temperature, and it shows that the hardness and density gradually increases with increasing sintering temperature. Abrasion wear test result reveals that the composite sintered at 1500 °C shows high abrasion resistance (wt. loss ~ 0.016 g) and the lowest abrasion resistance was observed for the composite sample sintered at 1100 °C (wt. loss ~ 1.459 g). The profilometry surface roughness study shows that sample sintered at 1100 °C shows maximum roughness (R{sub a} = 6.53 µm) compared to the sample sintered at 1500 °C (R{sub a} = 0.66 µm) corroborating the abrasion wear test results.

36 MATERIALS SCIENCE↗

Wear-Resistance Investigations on Ceramic Coatings for Lunar Dust Mitigation

Lunar dust has posed a major challenge to exploration efforts due to abrasion and impact. This work focuses on fundamental studies on ceramic coatings as candidates for enhanced resistance to impact and wear. As a first step, standard and modified approaches to the method of abrasion testing were explored for options to incorporate lunar regolith as wear media, the effects of which were presented for AL6061-T6 control samples. Following this, wear results for air plasma-sprayed (APS) alumina coatings were investigated due to their superior strength and surface hardness. In addition, APS 8 wt % yttria-stabilized zirconia (8YSZ) coatings were studied for their strength and martensitic transformation toughness. Measurements were made by assessing the mass loss, with a standard scale at various intervals. In addition, surface roughness was measured with a profilometer and features identified with a high-resolution microscope. The findings demonstrated that wear media has a distinct effect on the abrasion. The alumina coatings demonstrated improved wear over 8YSZ. However, the tailorability of 8YSZ makes it an attractive option to continue to modify as a wear-resistant coating to protect against lunar dust abrasion. The results of these measurements provide insight into the wear behavior of future directions in candidate ceramic coatings for the harsh lunar environment.

ceramic coatings↗

Wear-Resistance Investigations on Ceramic Coatings for Lunar Dust Mitigation

Lunar dust has posed a major challenge to exploration efforts due to abrasion and impact. This work focuses on fundamental studies on ceramic coatings as candidates for enhanced resistance to impact and wear. As a first step, standard and modified approaches to the method of abrasion testing were explored for options to incorporate lunar regolith as wear media, the effects of which were presented for AL6061-T6 control samples. Following this, wear results for air plasma-sprayed (APS) alumina coatings were investigated due to their superior strength and surface hardness. In addition, APS 8 wt % yttria-stabilized zirconia (8YSZ) coatings were studied for their strength and martensitic transformation toughness. Measurements were made by assessing the mass loss, with a standard scale at various intervals. In addition, surface roughness was measured with a profilometer and features identified with a high-resolution microscope. The findings demonstrated that wear media has a distinct effect on the abrasion. The alumina coatings demonstrated improved wear over 8YSZ. However, the tailorability of 8YSZ makes it an attractive option to continue to modify as a wear-resistant coating to protect against lunar dust abrasion. The results of these measurements provide insight into the wear behavior of future directions in candidate ceramic coatings for the harsh lunar environment.

ceramic coatings↗

Wear Behavior of an Ultra-High-Strength Eutectoid Steel

Wear behavior of an ultra-high-strength AISI 1080 steel developed through incomplete austenitization-based combined cyclic heat treatment is investigated in comparison with annealed and conventional hardened and tempered conditions against an alumina disk (sliding speed = 1 m s{sup −1}) using a pin-on-disk tribometer at a load range of 7.35-14.7 N. On a gross scale, the mechanism of surface damage involves adhesive wear coupled with abrasive wear (microcutting effects in particular) at lower loads. At higher loads, mainly the abrasive wear (both microcutting and microploughing mechanisms) and evolution of adherent oxide are observed. Besides, microhardness of matrix increases with load indicating substantial strain hardening during wear test. The rate of overall wear is found to increase with load. As-received annealed steel with the lowest initial hardness suffers from severe abrasive wear, thereby exhibiting the highest wear loss. Such a severe wear loss is not observed in conventional hardened and tempered and combined cyclic heat treatment conditions. Combined cyclic heat-treated steel exhibits the greatest wear resistance (lowest wear loss) due to its initial high hardness and evolution of hard abrasion-resistant tribolayer during wear test at higher load.

36 MATERIALS SCIENCE↗

Study on Tribological Properties of CoCrMo Alloys against Metals and Ceramics as Bearing Materials for Artificial Cervical Disc

CoCrMo alloys are believed to be a kind of potential material for artificial cervical disc. However, the tribological properties of CoCrMo alloys against different metals and ceramics are not systematically studied. In this study, the tribological behaviors of CoCrMo alloys against metals (316L, Ti6Al4V) and ceramics (Si{sub 3}N{sub 4}, ZrO{sub 2}) were focused under dry friction and 25 wt.% newborn calf serum (NCS)-lubricated conditions using a ball-on-disc apparatus under reciprocating motion. The microstructure, composition and hardness of CoCrMo alloys were characterized using x-ray diffraction, scanning electron microscopy (SEM) and hardness testers, respectively. The contact angles of the CoCrMo alloys with deionized water and 25 wt.% NCS were measured by the OCA contact angle measuring instrument. The maximum wear width, wear depth and wear volume were measured by three-dimensional white light interference. The morphology and the EDX analysis of the wear marks on CoCrMo alloys were examined by SEM to determine the basic mechanism of friction and wear. The dominant wear mechanism in dry friction for CoCrMo alloys against all pairings was severe abrasive wear, accompanied with a lot of material transfer. Under 25 wt.% NCS-lubricated condition, the wear mechanism for CoCrMo alloys against ceramics (Si{sub 3}N{sub 4}, ZrO{sub 2}) was also mainly severe abrasive wear. However, severe abrasive wear and electrochemical corrosion occurred for the CoCrMo-316L pairing under lubrication. Severe abrasive wear, adhesive wear and electrochemical corrosion occurred for the CoCrMo-Ti6Al4V pairing under lubrication. According to the results, the tribological properties of CoCrMo alloys against ceramics were better than those against metals. The CoCrMo-ZrO{sub 2} pairing displayed the best tribological behaviors and could be taken as a potential candidate bearing material for artificial cervical disc.

36 MATERIALS SCIENCE↗

Applications of tribology to determine attrition by wear of particulate solids in CFB systems

In recent years, much attention has been focused on the development of novel technologies for carbon capture and chemicals production that utilize a circulating fluidized bed (CFB) configuration; examples include chemical looping combustion and circulation of temperature swing adsorbents in a CFB configuration for CO 2 capture. A major uncertainty in determining the economic feasibility of these technologies is the required solids makeup rate, which, among other factors, is due to impact and wear attrition at various locations, including standpipes, cyclones, and the gas jets in fluid beds. While correlations have been developed that estimate the attrition rates at these areas, these correlations are dependent on constants that are uncertain without extensive experiment in the corresponding unit operation. Thus, it is difficult to determine the attrition rate a priori without performing extensive experiments on the materials or scaling up entirely. In this work, the authors outline a methodology for predictive attrition based on fundamental material properties from fields of tribology—specifically, the study of wear—to the knowledge of forces and sliding distances determined from hydrodynamic models to develop basic attrition models for novel CFB systems. The equations are derived for the standpipe and cyclone, which are common components found in CFBs, and the cyclone equation is compared to experimental data of attrition in the literature. The cyclone equation derived in this work results in an abrasion rate based on (1) material properties such as particle density and hardness, (2) inlet velocity, and (3) cyclone geometry. According to this equation, increasing the diameter of the cyclone and the solids inlet velocity tends to increase the rate of abrasion of the catalyst, while decreasing the hardness increases the abrasion rate. The functionality of the increasing attrition rate with velocity increase implies that increasing the efficiency of the cyclone may also increase the attrition rate via abrasion. With modifications to the severity coefficient term to include the solids loading, the cyclone equation derived in this work fits data from Reppenhagen and Werther with a coefficient of determination (R2) of 92%.

01 COAL, LIGNITE, AND PEAT↗

Attrition of hematite particles for chemical looping combustion in a conical jet cup

The attrition of hematite particles for use in the chemical looping combustion process was investigated using a cold flow jet cup test. Jet cup attrition experiments are commonly used for bulk attrition testing of fluidized bed catalyst. The results indicate that the particle attrition in the jet cup cold flow experiments arises from surface abrasion due to particle-particle and particle-wall interactions. Experiments indicate that the measured cumulative mass loss increases with attrition time. However, the attrition rate decreases sharply at the early stage of attrition, and gradually, the rate decline slows and approaches a constant value with increasing attrition time. Furthermore, the influence of inlet gas velocity and solid inventory is discussed. As inlet gas velocities increase, the measured cumulative mass loss also increases. However, as the solid inventory increases, the cumulative mass loss decreases. The results also show that the jet cup experiments quantitatively compare with low magnitude tangential forces which is an indication of attrition through abrasion as the primary mechanism. It is determined through particle size distributions before and after which show a small shift of the main peaks with no peak broadening while producing a small number of fines. By using the mass of abraded fines and the widely-used Archard model for abrasive attrition, the specific wear rate coefficient can be predicted as a function of time. The wear coefficient calculation further identifies that the abrasion mechanism as the primary mechanism of attrition.

42 ENGINEERING↗