Search NASA⌕ Search

SEARCH · Search NASA

Results for “AIRCRAFT DETECTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS2019

A Comparison of Two Terminal Area Detect and Avoid Well Clear Definitions

Technical requirements are currently under development for a detect and avoid system (DAA) that would support the operation of Unmanned Aircraft Systems (UAS) within the National Airspace System (NAS). Such a system would aid UAS operators in maintaining sufficient separation, or "well clear", from other aircraft in their vicinity. The first set of technical standards for a UAS DAA system (referred to as "Phase 1" requirements) was limited to UAS operations transiting through Class D, E, and G airspace to, or from, Class A (or special-use) airspace. Explicitly out of scope of the Phase 1 requirements was the operation of UAS within terminal airspace in the NAS. Fern, Rorie, Roberts and Monk (2018) explored the application of a Phase 1 DAA system within Class D terminal airspace in a human-in-the-loop simulation. The results of the study demonstrated a poor fit of the Phase 1 DAA well clear (DWC) definition to these terminal operations. The original DWC definition was designed for the en-route environment and could not account for the complex, tightly-choreographed nature of traffic typically found near an airport. The interaction of the en-route DWC definition and the terminal area traffic led to excessive DAA alerting against safely-separated traffic. The frequent alerting quickly degraded pilots' ability to discriminate between encounters where a maneuver was or was not necessary. This resulted in slower response times, higher rates of losses of DAA well clear, and more severe losses of DAA well clear than had been observed in previous DAA research (e.g., Rorie et al., 2017). The current paper reports on a follow-on study to Fern et al. (2018) that tested two DWC definitions designed to accommodate standard terminal area operating procedures, such as traffic in the downwind leg of a VFR traffic pattern while the UAS is on final. The two definitions utilized identical horizontal and vertical thresholds but differed in whether or not Tau (a function that takes into account the closure rate of two aircraft) was included as a part of the DWC hazard zone. The "Tau" DWC candidate definition nominally extended the DWC hazard zone by 15 seconds in the direction of the intruder aircraft, while the "No Tau" DWC candidate definition did not extend the DWC hazard zone. The results of this follow-on study indicated that both candidate definitions improved pilot and DAA system performance relative to Fern et al (2018). Pilot response times and rates of losses of DWC returned to levels comparable to earlier research in the en-route environment. Several important differences between the two DWC candidate definitions, however, are also discussed.

Terminal Area↗
NASA NTRS2019

Terminal Area Test Vector Development

This presentation provides an overview of work being done to develop test vectors for the terminal area, in coordination with RTCA Special Committee 228, an organization developing the Minimum Operational Performance Standards (MOPS) for Unmanned Aircraft Systems (UAS) Detect and Avoid (DAA) systems. The work leverages existing encounter data to develop a set of encounters to be used to define and refine both performance-based and functionally-based terminal area MOPS requirements. The encounter set would be used across various organizations supporting MOPS terminal area requirements development to provide some level of consistency in terms of terminal area assumptions. The work will investigate other potentially applicable data sets and make any similarly needed adjustments to arrive at a consolidated set of terminal area encounters.

terminal area↗
NASA NTRSDate not supplied

TPSAS-NF1676L-12156-DND

The IVHM project recommends nine priorities for future IVHM research. Strain measurement technology is one of the nine recommendations. The Decadal Survey of Civil Aeronautics: Foundation for the Future, identified IVHM as the top NASA and national priority within the area of materials and structures. The survey also identified IVHM systems that warrant attention over the next decade such as “locally self-powered, wireless microelectromechanical sensors of various types tiny enough that very large numbers of sensors become practical.” Standard strain gages have been used to detect cracks in aircraft, and have been used to monitor load conditions and fatigue in airframes. High temperature devices will be able to monitor structural health in areas that are inaccessible today.

Cy Wilson↗
NASA NTRS2014

Pilot Evaluation of a UAS Detect-and-Avoid System's Effectiveness in Remaining Well Clear

Unmanned aircraft will equip with a detect-and-avoid (DAA) system that enables them to comply with the requirement to "see and avoid" other aircraft, an important layer in the overall set of procedural, strategic and tactical separation methods designed to prevent mid-air collisions. Regulators will establish minimum operating standards for DAA effectiveness, but different combinations of algorithms, displays and procedures could be used to meet those standards. The research presented in this paper indicates the effectiveness of the combined pilot-DAA system as a function of the DAA design requirements and provides data that may be used to model the behavior of pilots when employing such systems. Two simulations involving 21 professional unmanned aircraft system (UAS) pilots evaluated eight different DAA system designs in order to assess their ability to maintain the "well clear" separation standard, i.e., the state of maintaining a safe distance from other aircraft that would not normally cause the initiation of a collision avoidance maneuver by either aircraft. When the traffic display was integrated with the primary mission map directly in front of the pilot, there were fewer losses of well clear. Greater warning time provided to the pilot was strongly correlated with success in remaining well clear. Pilots' ability to separate from aircraft with cooperative and non-cooperative surveillance systems was nearly the same after accounting for the amount of alert time provided in each encounter, although the limited surveillance volume for the airborne-equipped aircraft meant alerts tended to occur later and therefore were more difficult to resolve.

detect-and-avoid↗
NASA NTRS2015

Pilot Evaluation of a UAS Detect-and-Avoid System's Effectiveness in Remaining Well Clear

Unmanned aircraft will equip with a detect-and-avoid (DAA) system that allows them to comply with the requirement to see and avoid other aircraft, an important layer in the overall set of procedural, strategic and tactical separation methods designed to prevent mid-air collisions. Although the effectiveness of the DAA system will be set to a minimum threshold by regulators, different combinations of algorithms, displays and procedures could be used to meet that minimum. The research presented in this paper indicates the effectiveness of the combined pilot-DAA system as a function of the DAA design requirements and provides data that may be used to model the behavior of pilots when employing such systems. Over the course of two simulations 21 professional UAS pilots evaluated eight different DAA system designs and metrics were collected on their ability to maintain the well clear separation standard. The independent variables were the time horizon at which pilots were alerted to potential losses of well clear, the location of the traffic display, and the tools and informational elements available on the display to aid the pilot in detecting and resolving those potential losses. In the second experiment the UAS encountered two categories of aircraft: those equipped with simulated transponders that could be seen dozens of miles away and those without that were only detectable by a simulated radar within a range of six nautical miles. The data indicate that integrating the traffic display with the primary mission map directly in front of the pilot reduced the frequency of losses of well clear. Improved detection and resolution tools, including explicit maneuver guidance and a trial planning capability, had less of an effect in reducing the frequency of losses but significantly reduced the time in loss when they occurred. The amount of warning time provided to the pilot had a strong effect on their ability to remain well clear: when alerts were first presented with less than about 15 seconds to a predicted loss of well clear pilots were able to maneuver successfully in only 26 percent of encounters, whereas they were about 83 percent successful when they had more than 15 seconds. Pilots' ability to separate from the two categories of aircraft was nearly the same after accounting for the amount of alert time provided in each encounter, although the limited surveillance volume for the non-transponder equipped aircraft meant alerts tended to occur later and therefore were more difficult to resolve.

loss of well clear↗
NASA NTRS1973

Census cities experiment in urban change detection

The author has identified the following significant results. Work continues on mapping of 1970 urban land use from 1970 census contemporaneous aircraft photography. In addition, change detection analysis from 1972 aircraft photography is underway for several urban test sites. Land use maps, mosaics, and census overlays for the two largest urban test sites are nearing publication readiness. Preliminary examinations of ERTS-1 imagery of San Francisco Bay have been conducted which show that tracts of land of more than 10 acres in size which are undergoing development in an urban setting can be identified. In addition, each spectral band is being evaluated as to its utility for urban analyses. It has been found that MSS infrared band 7 helps to differentiate intra-urban land use details not found in other MSS bands or in the RBV coverage of the same scene. Good quality false CIR composites have been generated from 9 x 9 inch positive MSS bands using the Diazo process.

Wray, J. R.↗
NASA NTRS1993

An aircraft instrument design for in situ tropospheric OH measurements by laser induced fluorescence at low pressures

The hydroxyl radical (OH) is important for many processes involved in tropospheric chemistry. For instance, it initiates the photochemical degradation of gases that cause global climate change, such as methane and the chlorofluorocarbon substitutes (HCFCs). Because of its reactivity, its abundances are less than 0.1 pptv. Thus, OH has been very difficult to measure accurately, despite its importance. Techniques have evolved, however, so that good measurements of tropospheric OH abundances are now possible. One of these techniques that is adaptable to aircraft measurements is the laser induced fluorescence detection of the OH radical in a detection chamber at low pressures. The current ground-based instrument, which can be readily adapted to aircraft, can detect OH abundances of 1.4 x 10 exp 5 OH molecules/cu cm with S/N = 2 in 30 sec, and 5 x 10 exp 4/cu cm in 5 min.

Brune, William H.↗
NASA NTRS1976

Laser Doppler technology applied to atmospheric environmental operating problems

Carbon dioxide laser Doppler ground wind data were very favorably compared with data from standard anemometers. As a result of these measurements, two breadboard systems were developed for taking research data: a continuous wave velocimeter and a pulsed Doppler system. The scanning continuous wave laser Doppler velocimeter developed for detecting, tracking and measuring aircraft wake vortices was successfully tested at an airport where it located vortices to an accuracy of 3 meters at a range of 150 meters. The airborne pulsed laser Doppler system was developed to detect and measure clear air turbulence (CAT). This system was tested aboard an aircraft, but jet stream CAT was not encountered. However, low altitude turbulence in cumulus clouds near a mountain range was detected by the system and encountered by the aircraft at the predicted time.

Weaver, E. A.↗
NASA NTRS1992

A millimeter-wave radiometer for detecting microbursts

This paper describes a millimeter-wave radiometer for the detection of wind shear from airborne platforms or at airport terminals. This proposed instrument will operate near the group of atmospheric oxygen absorptions centered near 60 GHz, which it will use to sense temperature from a distance. The instrument will use two channels to provide two different temperature measurements, providing the basis for solution of two equations in two unknowns, which are range to the wind shear plume and its temperature. A third channel will measure ambient atmospheric temperature. Depending on the temperature difference between the wind-shear plume and ambient, the standard deviation of range measurement accuracy is expected to be about 1 km at 5 km range, while the temperature measurement standard deviation will be about one-fourth the temperature difference between plume and ambient at this range. The instrument is expected to perform usefully at ranges up to 10 km, giving adequate warning of the presence of wind shear even for high performance jet aircraft. Other atmospheric hazards which might be detected by this radiometer include aircraft wakes and vortices, clear-air turbulence, and wind rotors, although the latter two phenomena would be detected by an airborne version of the instrument. A separate radiometer channel will be provided in the proposed instrument to detect aircraft wakes and vortices based on perturbation of the spectrum of microscopic atmospheric temperature fluctuations caused by the passage of large aircraft.

Mcmillan, Robert↗
NASA NTRS2006

Conflict Detection Using Variable Four-Dimensional Uncertainty Bounds to Control Missed Alerts

Decision-support tools for maintaining pairwise aircraft separation rely on conflict detection to alert the operator when the predicted trajectories of aircraft will result in a loss of separation. But aircraft frequently do not follow their predicted trajectories exactly. This can cause missed alerts and the failure of strategic separation procedures. We present a technique for modeling a bounded region of uncertainty around a four-dimensional predicted trajectory and an algorithm for detecting conflicts between trajectories modeled in this way that avoids missed alerts as long as the aircraft remain within the specified regions of uncertainty. In addition, we present an algorithm for detecting the intrusion of a trajectory modeled in this way into an area hazard modeled as a polygonal region. The size of the region of uncertainty can vary along the trajectory continually and independently in the along-path, cross-track, and vertical dimensions, providing an opportunity to reduce the likelihood of false alerts while protecting against typical prediction errors. The algorithm has been implemented in the Autonomous Operations Planner, a NASA Langley prototype decision support tool for airborne self-separation.

Karr, David A.↗
NASA NTRS2019

A Detect and Avoid System in the Context of Multiple-Unmanned Aircraft Systems Operations

NASA's Unmanned Aircraft Systems Integration into the National Airspace System (UAS in the NAS) project examines the technical barriers associated with the operation of UAS in civil airspace. For UAS, the removal of the pilot from onboard the aircraft has eliminated the ability of the ground-based pilot in command (PIC) to use out-the-window visual information to make judgements about a potential threat of a loss of well clear with another aircraft. NASA's Phase 1 research supported the development of a Detect and Avoid (DAA) system that supports the ground-based pilot's ability to detect potential traffic conflicts and determine a resolution maneuver, but existing display/alerting requirements did not account for multiple UAS control (1:N). Demands for increased scalability of UAS in the NAS operations are expected to create a need for simultaneous control of UAs, and thus, a new DAA HMI design will likely be necessary. Previous research, however, has found performance degradations as the number of vehicles under operator control has increased. The purpose of the current human-in-the-loop (HITL) simulation was to examine the viability of 1:N operations with the Phase 1 DAA alerting and guidance. Sixteen UAS pilots flew three scenarios with varying number of UAs under their control (1:1, 1:3, 1:5). In addition to their supervisory and sensor mission responsibilities, pilots were to utilize the DAA system to remain DAA well clear (DWC) during scripted conflicts of mixed severity. Measured response times, separation performance, mission task data, and subjective feedback were collected to assess how the multi-UAS control configuration impacted pilots' ability to maintain DAA well clear and perform the mission tasks. Overall, the DAA system proved surprisingly adaptive to multi-UAS control for preventing losses of DAA well clear (LoDWC). The findings suggest that, while multi-UAS operators are able to maintain safe separation (DWC) from other traffic, their ability to efficiently perform missions drastically decreases with their number of controlled vehicles. Pilot feedback indicated that, for this context, the use of automation support tools for completing and managing mission tasks would be appropriate and desired, especially for ensuring efficient use of assets. Finally, human-machine interface (HMI) design considerations for multi-UAS operations are discussed.

Monk, Kevin J.↗
NASA NTRS1981

Digital detection and processing of laser beacon signals for aircraft collision hazard warning

A low-cost collision hazard warning system suitable for implementation in both general and commercial aviation is presented. Laser beacon systems are used as sources of accurate relative position information that are not dependent on communication between aircraft or with the ground. The beacon system consists of a rotating low-power laser beacon, detector arrays with special optics for wide angle acceptance and filtering of solar background light, microprocessors for proximity and relative trajectory computation, and pilot displays of potential hazards. The laser beacon system provides direct measurements of relative aircraft positions; using optimal nonlinear estimation theory, the measurements resulting from the current beacon sweep are combined with previous data to provide the best estimate of aircraft proximity, heading, minimium passing distance, and time to closest approach.

Sweet, L. M.↗
NASA NTRS2005

Handling Trajectory Uncertainties for Airborne Conflict Management

Airborne conflict management is an enabling capability for NASA's Distributed Air-Ground Traffic Management (DAG-TM) concept. DAGTM has the goal of significantly increasing capacity within the National Airspace System, while maintaining or improving safety. Under DAG-TM, autonomous aircraft maintain separation from each other and from managed aircraft unequipped for autonomous flight. NASA Langley Research Center has developed the Autonomous Operations Planner (AOP), an onboard decision support system that provides airborne conflict management (ACM) and strategic flight planning support for autonomous aircraft pilots. The AOP performs conflict detection, prevention, and resolution from nearby traffic aircraft and area hazards. Traffic trajectory information is assumed to be provided by Automatic Dependent Surveillance Broadcast (ADS-B). Reliable trajectory prediction is a key capability for providing effective ACM functions. Trajectory uncertainties due to environmental effects, differences in aircraft systems and performance, and unknown intent information lead to prediction errors that can adversely affect AOP performance. To accommodate these uncertainties, the AOP has been enhanced to create cross-track, vertical, and along-track buffers along the predicted trajectories of both ownship and traffic aircraft. These buffers will be structured based on prediction errors noted from previous simulations such as a recent Joint Experiment between NASA Ames and Langley Research Centers and from other outside studies. Currently defined ADS-B parameters related to navigation capability, trajectory type, and path conformance will be used to support the algorithms that generate the buffers.

Barhydt, Richard↗
NASA NTRS2006

Runway Safety Monitor Algorithm for Single and Crossing Runway Incursion Detection and Alerting

The Runway Safety Monitor (RSM) is an aircraft based algorithm for runway incursion detection and alerting that was developed in support of NASA's Runway Incursion Prevention System (RIPS) research conducted under the NASA Aviation Safety and Security Program's Synthetic Vision System project. The RSM algorithm provides warnings of runway incursions in sufficient time for pilots to take evasive action and avoid accidents during landings, takeoffs or when taxiing on the runway. The report documents the RSM software and describes in detail how RSM performs runway incursion detection and alerting functions for NASA RIPS. The report also describes the RIPS flight tests conducted at the Reno/Tahoe International Airport (RNO) and the Wallops Flight Facility (WAL) during July and August of 2004, and the RSM performance results and lessons learned from those flight tests.

Green, David F., Jr.↗
NASA NTRS2013

Millimeter-Wave Localizers for Aircraft-to-Aircraft Approach Navigation

Aerial refueling technology for both manned and unmanned aircraft is critical for operations where extended aircraft flight time is required. Existing refueling assets are typically manned aircraft, which couple to a second aircraft through the use of a refueling boom. Alignment and mating of the two aircraft continues to rely on human control with use of high-resolution cameras. With the recent advances in unmanned aircraft, it would be highly advantageous to remove/reduce human control from the refueling process, simplifying the amount of remote mission management and enabling new operational scenarios. Existing aerial refueling uses a camera, making it non-autonomous and prone to human error. Existing commercial localizer technology has proven robust and reliable, but not suited for aircraft-to-aircraft approaches like in aerial refueling scenarios since the resolution is too coarse (approximately one meter). A localizer approach system for aircraft-to-aircraft docking can be constructed using the same modulation with a millimeterwave carrier to provide high resolution. One technology used to remotely align commercial aircraft on approach to a runway are ILS (instrument landing systems). ILS have been in service within the U.S. for almost 50 years. In a commercial ILS, two partially overlapping beams of UHF (109 to 126 MHz) are broadcast from an antenna array so that their overlapping region defines the centerline of the runway. This is called a localizer system and is responsible for horizontal alignment of the approach. One beam is modulated with a 150-Hz tone, while the other with a 90-Hz tone. Through comparison of the modulation depths of both tones, an autopilot system aligns the approaching aircraft with the runway centerline. A similar system called a glide-slope (GS) exists in the 320-to-330MHz band for vertical alignment of the approach. While this technology has been proven reliable for millions of commercial flights annually, its UHF nature limits its ability to operate beyond the 1-to-2-meter precisions associated with commercial runway width. A prototype ILS-type system operates at millimeter-wave frequencies to provide automatic and robust approach control for aerial refueling. The system allows for the coupling process to remain completely autonomous, as a boom operator is no longer required. Operating beyond 100 GHz provides enough resolution and a narrow enough beamwidth that an approach corridor of centimeter scales can be maintained. Two modules were used to accomplish this task. The first module is a localizer/glide-slope module that can be fitted on a refueling aircraft. This module provides the navigation beams for aligning the approaching aircraft. The second module is navigational receiver fitted onto the approaching aircraft to be re fueled that can detect the approach beams. Since unmanned aircraft have a limited payload size and limited electrical power, the receiver portion was implemented in CMOS (complementary metal oxide semiconductor) technology based on a super-regenerative receiver (SRR) architecture. The SRR achieves mW-level power consumption and chip sizes less than l mm2. While super-regenerative techniques have small bandwidths that limit use in communication systems, their advantages of high sensitivity, low complexity, and low power make them ideal in this situation where modulating tones of less than 1 kHz are used.

Tang, Adrian J.↗
NASA NTRS2018

Analysis of Influence of UAS Speed Range and Turn Performance on Detect and Avoid Sensor Requirements

In support of NASA’s Unmanned Aircraft Systems Integration in the National Airspace System project and RTCA Special Committee 228, an analysis has been performed to provide insight in to the trade space between unmanned aircraft speed and turn capability and detect and avoid sensor range requirements. The work was done as an initial part of the effort to understand low size, weight, and power sensor requirements for aircraft that have a limited speed envelope or can limit the envelope for portions of their mission and may be able to turn at higher than “standard rate.” Range and timeline reductions coming from limiting speed range and from increasing available turn rate in some speed ranges are shown.

Jack, Devin P.↗