Search NASA⌕ Search

SEARCH · Search NASA

Results for “ALUMINIUM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Intrinsic reactivity and dissolution characteristics of tetracalcium aluminoferrite

Tetracalcium aluminoferrite is one of the main phases of Portland cement, the dissolution characteristics of which however have not been fully revealed. This work adopted first-principles calculations and Mössbauer spectroscopy as well as X-ray diffraction analysis to clarify the intrinsic reactivity of different species of tetracalcium aluminoferrite crystals. Ca ions are the most reactive species of tetracalcium aluminoferrite and Al ions are slightly more reactive than Fe ions. Moreover, the tetrahedral Al and Fe ions are more reactive than the octahedral Al and Fe ions. These indicate dissolution characteristics of tetracalcium aluminoferrite crystals, namely, Ca ions dissolve first and the tetrahedral species dissolve faster than the octahedral species. After the initial dissolution, the dissolved ions nucleate and grow on the defective surface of C{sub 4}AF and the C{sub 4}AF residues are fully hydroxylated. The further hydration thereafter becomes the complex dissolution with the nucleation and growth of hydration products.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Impact of KOH on the interfacial precipitation rates of C-S-H during the early hydration of C3S

In this work we investigated the influence of alkalis on the hydration of two triclinic samples of C{sub 3}S. One pure C{sub 3}S and one Al-doped C{sub 3}S (0.5 wt.‐% Al{sub 2}O{sub 3}). We added differently concentrated KOH solutions representing alkalis in the pore solution, which lead to an increase of the interfacial precipitation rates of C-S-H during the hydration of C{sub 3}S compared to the hydration without KOH. Isothermal calorimetry was conducted for the determination of the rates of reaction during the hydration process and ICP-OES measurements for the determination of the pore solution composition at certain times of hydration. The increasing effect of KOH solution on the calculated interfacial precipitation rates from pore solution data can explain the enhancement of the rates of reaction recorded by heat flow calorimetry during the early hydration. Therefore, the interfacial precipitation rates of C-S-H can accurately describe the acceleration effect of alkalis on the early hydration of C{sub 3}S.

36 MATERIALS SCIENCE↗
DOE OSTI2021

An insight on the effect of sodium and silicon on microstructure and crystallography of high alumina cements

In the present study the influence of minor elements (Na{sub 2}O and SiO{sub 2}) on the mineralogy, chemistry and microstructure of High Alumina Cements (HACs) has been investigated. HACs have several advantages respected to Ordinary Portland Cement (OPC) but the shortage of Al-rich raw materials represents a limiting factor: re-use of Al-rich waste as raw material represents a solution but it will add minor elements to the raw meal that could change HACs properties. For the first time, four commercial HACs, doped with sodium and silicon, and one synthetic HAC, only highly doped in sodium, were studied through a multidisciplinary approach by combining conventional and unconventional analytical techniques. Results highlighted that (i) sodium and silicon were mainly incorporated in a sodium-rich phase (Na-phase, NCA{sub 2}, Na{sub 1.9}CaAl{sub 3.9}Si{sub 0.1}O{sub 8}), (ii) no minor phases such as gehlenite and/or mayenite occurred, and (iii) CA (CaAl{sub 2}O{sub 4}) and CA{sub 2} (CaAl{sub 4}O{sub 7}) revealed a limited ionic substitution.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Synthesis, characterization, and thermodynamic study of selected K-based zeolites

Potassium-rich zeolites often occur in cementitious systems, as K{sup +} is widespread in various cementitious materials, such as Portland, blended and alkali-activated cements. The knowledge of their stability and of thermodynamic models for solid solutions with Na{sup +} and Ca{sup 2+} are critical to understand long-term development and durability in such cements. Completing previous studies on Na- and Ca-based zeolites, the current work aims to determine the thermodynamic data of 14 types of K-based zeolites, which could possibly form in cementitious systems. The zeolites were synthesized hydrothermally, exchanged with K{sup +}, and characterized thoroughly with respect to framework structures, elemental compositions, water contents, and bond variations. Their thermodynamic properties were derived from the experimental solubility data, which allowed establishing predominance diagrams in the K{sub 2}O-SiO{sub 2}-Al{sub 2}O{sub 3}-H{sub 2}O system. The K-based zeolites typically showed the lowest solubility between 0 and 100 °C, with the notable exception of Ca-gismondine and two Na-based zeolites: natrolite and Na-mordenite.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effect of seawater as mixing water on the hydration behaviour of tricalcium aluminate

This study explored the mechanism of the effect of seawater on tricalcium aluminate (C{sub 3}A) hydration. The results showed that seawater retarded C{sub 3}A hydration and reduced the reaction degree of C{sub 3}A. The co-existence or ion pairing of Ca{sup 2+} and SO{sub 4}{sup 2−} onto the surface of C{sub 3}A poisoning the reactive sites is the main reason for this retardation. Besides, the precipitation of Mg(OH){sub 2} on the surface of C{sub 3}A would prolong the induction period for another 30 min and then consequently decrease the dissolution rate of C{sub 3}A hydration. Trace amounts of MgSO{sub 4}{sup 0} and Mg{sup 2+} present in the alkaline solution had little retardation effect. It was also found that Cl{sup −} would preferentially react with C{sub 3}A to form Friedel's salt, rather than forming hydroxy-AFm as that in the C{sub 3}A-deionized water paste. The direct formation of Friedel's salt resulted in an accumulation of Al{sup 3+} in solution, which would also hinder the subsequent dissolution of C{sub 3}A.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Predicting CaO-(MgO)-Al2O3-SiO2 glass reactivity in alkaline environments from force field molecular dynamics simulations

In this investigation, force field-based molecular dynamics (MD) simulations have been employed to generate detailed structural representations for a range of amorphous quaternary CaO-MgO-Al{sub 2}O{sub 3}-SiO{sub 2} (CMAS) and ternary CaO-Al{sub 2}O{sub 3}-SiO{sub 2} (CAS) glasses. Comparison of the simulation results with select experimental X-ray and neutron total scattering and literature data reveals that the MD-generated structures have captured the key structural features of these CMAS and CAS glasses. Based on the MD-generated structural representations, we have developed two structural descriptors, specifically (i) average metal oxide dissociation energy (AMODE) and (ii) average self-diffusion coefficient (ASDC) of all the atoms at melting. Both structural descriptors are seen to more accurately predict the relative glass reactivity than the commonly used degree of depolymerization parameter, especially for the eight synthetic CAS glasses that span a wide compositional range. Hence these descriptors hold great promise for predicting CMAS and CAS glass reactivity in alkaline environments from compositional information.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Investigation of aluminum nitrate as a set retarder of magnesium potassium phosphate cement: Mechanisms involved in diluted suspension

In this study, the influence of aluminum nitrate on the hydration process of magnesium potassium phosphate (MKP) cement was investigated experimentally and through thermodynamic modelling using diluted systems with Mg/PO{sub 4} molar ratio and water-to-cement ratio of 1 and 100 respectively. Three processes contributed to retard cement hydration: the acidic nature of aluminum nitrate which reduced the initial pH of the solution by two units, the early precipitation of a taranakite-like amorphous potassium aluminophosphate, which reduced the aqueous phosphate and potassium concentrations, and a salt effect due to the presence of soluble nitrate. Precipitation of potassium-containing magnesium phosphate hydrates, like Mg{sub 2}KH(PO{sub 4}){sub 2}⋅15H{sub 2}O and K-struvite, was prohibited, whereas precipitation of newberyite and cattiite was delayed. Furthermore, the modelled phase development with ongoing cement hydration agreed rather well with the experimental findings.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Coating adhesion of a chromate-containing epoxy primer on Al2024-T3 surface processed by laser-interference

In this work, the coating adhesion test results are presented for a primer that was coated on laser-interference structured surfaces of as-received Al2024-T3 specimens, i.e., without employing any polishing, cleaning, or any other surface alteration techniques. All of the laser-interference processing was performed by splitting the primary beam of a Q-switched Nd:YAG pulsed nanosecond laser into two beams and focused them to the same spot. The specimens were spray painted with a chromate-containing epoxy primer, CA7233, compliant to MIL-PRF-23377 Type I Class C2 specification. The adhesion of primer on Al surface with different treatments was assessed using the ASTM D3359 X-cut and cross-hatch tests. It was found that the laser processed specimens meet the performance requirements in the coating adhesion specifications by having a higher or identical ranking for coating adhesion specimens than those prepared with current state-of-the-art chemical conversion or sulfuric acid anodizing. The rastering with either 4 mm/s or 6 mm/s with a laser fluence of 1.78 J/cm2 is recommended to attain acceptable coating adhesion, even higher than that with the anodizing surface treatment.These results indicate that laser-interference shows significant potential as a non-chemical surface preparation technique for these coatings.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Improved catalytic activity of Mo x Ni y Al z thin films as electrocatalyst for hydrogen evolution reaction in alkaline media

In this work, we report activities of Mo x Ni y X z (where X is Al, Co, Cr, Cu, Fe, W)-based electrocatalysts for hydrogen evolution reaction (HER) in a 1 M NaOH solution. Mo x Ni y X z thin film electrocatslysts were prepared by magentron sputtering at 25°C and 800°C and characterized by scanning electron microscopy (SEM) with energy dispersive X-ray (EDX) analyzer and X-ray diffraction (XRD) analysis. Here, the catalytic activity of electrocatalyst was studied by cyclic voltammetry and electrochemical impedance spectroscopy. The electrocatalyst based on Mo 80 Ni 5 Al 15 (800°C) shows the best value of the overpotential (-181 mV) for HER from all tested ternary systems. XRD analysis indicates that HER activity only Mo 80 Ni 5 Al 15 thin films prepared at 800°C contained fcc phase. Other less active composition contained only bcc phase. The results obtained from impedance spectroscopy are consistent with the results from cyclic voltammetry. The stability of the prepared catalyst was studied by chronoamperometric analysis. The results from chronoamperometry show that HER activity of Mo 80 Ni 5 Al 15 prepared at 800°C, after very slight initial activity decrease, stays constant, while activity of Ni catalyst decreased almost twice in measured time window. Since Ni is commonly used industrial catalyst, Mo 80 Ni 5 Al 15 based alloy could be more attractive catalyst material for alkaline electrolyzers.

08 HYDROGEN↗
DOE OSTI2024

Spark plasma sintering of fuel meats for U 3 O 8 based dispersion fuels

Research and test reactors often use dispersion-type fuel due to its increased thermal conductivity and burn-up capabilities compared to conventional fuel. Al-U 3 O 8 (aluminumtriuranium octaoxide) dispersion fuels have several advantages over their competitors, such as higher service temperature and better stability of oxygen stoichiometry. However, the two-step fabrication of dispersion fuel causes undesirable porosity in cold-pressed fuel meats that is preserved in co-extruded fuel plates. To combat this, spark plasma sintering (SPS) was used for the fabrication of Al-15, 20, and 30 vol% U 3 O 8 and 8 and 12 vol% Mo-U 3 O 8 fuel meats for the Al-U 3 O 8 time. The in situ SPS data was used to construct and validate Master Sintering Curves (MSCs) with accuracies in Al fuels at 0.02 g/cm 3 , and Mo fuels at 0.07 and 0.17 g/cm 3 . The as-sintered fuel meats were characterised using x-ray diffraction (XRD) and scanning electron microscopy (SEM) to understand chemical and physical changes following the SPS process. The pellets exhibited very high relative densities, the U 3 O 8 was observed to undergo reduction to UO 2 .

Aluminium↗
DOE OSTI2024

Quantifying replication through repeated analysis of UVM-A, a liquid reference material for cosmogenic 10 Be and 26 Al studies

In this study, in-situ produced cosmogenic nuclide sample preparation and analysis is a complicated, multi-step process with numerous possible sources of error, many of which have not been robustly quantified. Here, we use a liquid reference material (UVM-A) to test whether the analytic precision associated with individual isotopic ratios (n = 96) measured at two Accelerator Mass Spectrometry facilities (Lawrence Livermore National Laboratory and Purdue Rare Isotope Measurement Laboratory) accurately represents the range of values determined for aliquots prepared in a single laboratory over a period of five years. We find that 10 Be/ 9 Be ratios measured at the different accelerator facilities (n = 26 and n = 70) have statistically indistinguishable central tendencies, matching to within 0.1 %. Based on this large dataset, we suggest preliminary consensus values for UVM-A of 1.45 ± 0.06 x 10 -13 for 10 Be/ 9 Be (mean, one standard deviation, n = 96) and 4.47 ± 0.22 x 10 -13 for 26 Al/ 27 Al (mean, one standard deviation, n = 27). For both 10 Be/ 9 Be and 26 Al/ 27 Al, the relative standard deviations of the measured ratios are similar to the reported analytic uncertainties of sample measurement, suggesting that sample preparation introduced little if any additional scatter beyond the uncertainty of isotopic analysis. This dataset demonstrates that robust sample preparation and measurement can generate isotope ratio data reproducible at the level of counting statistics.

58 GEOSCIENCES↗
DOE OSTI2024

Physical and Electrochemical Characterization of Aluminum Electrodes during Electrocoagulation

Electrocoagulation (EC) of synthetic groundwater was conducted using a sacrificial aluminum electrode in a flow-through EC reactor with short retention times (<1 min) under varying hydrodynamic and electrochemical conditions. The treated water was allowed to settle for 24 h and achieved silicate removal of up to 50 ± 4%, and hardness removal of 11 ± 1%. Physical, chemical, and electrochemical characterization was performed to explore changes in electrode surface morphology and composition. Electrochemical impedance spectroscopy (EIS) showed that chemical reactions at the electrode/water interface are sensitive to changes in the immediate chemical environment. We demonstrate that the most energy-intensive step in EC is aluminum dissolution at the anode, which remained fairly constant due to the continuous renewal of the anode’s surface, a result of aluminum dissolution. At the cathode, a structural change in the oxide layer, from γ-Al 2 O 3 to gibbsite, was detected by grazing-incidence X-ray diffraction, which decreased the resistance to charge transfer at the cathode surface, resulting in decreased electrode resistance. The high flow rate in the system minimized the accumulation of aluminum hydroxide solids and aluminum ions at the electrode/water interface, which minimized the formation of thick scalants and amorphous Al(OH) 3 on the cathode and anode, respectively. In conclusion, it was further demonstrated by EIS that under these conditions the resistance to charge transfer was constant throughout the duration of the experiment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Optical constants of magnetron sputtered aluminum in the range 17–1300 eV with improved accuracy and ultrahigh resolution in the L absorption edge region

This work determines a new set of EUV/x-ray optical constants for aluminum (Al), one of the most important materials in science and technology. Absolute photoabsorption (transmittance) measurements in the 17–1300 eV spectral range were performed on freestanding Al films protected by carbon (C) layers, to prevent oxidation. The dispersive portion of the refractive index was obtained via the Kramers–Kronig transformation. Our data provide significant improvements in accuracy compared to previously tabulated values and reveal fine structure in the Al L 1 and L 2,3 regions, with photon energy step sizes as small as 0.02 eV. The implications of this work in the successful realization of EUV/x-ray instruments and in the validation of atomic and molecular physics models are also discussed.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2025

Low energy backgrounds and excess noise in a two-channel low-threshold calorimeter

Here, we describe observations of low energy excess (LEE) events, background events observed in all light dark matter direct detection calorimeters, and noise in a transition edge sensor based two-channel silicon athermal phonon detector with 375 meV baseline energy resolution. We measure two distinct LEE populations: “shared” multichannel events with a pulse shape consistent with substrate athermal phonon events and sub-eV events that couple nearly exclusively to a single channel with a significantly faster pulse shape. These “singles” are consistent with events occurring within the aluminum athermal phonon collection fins. Similarly, our measured detector noise is higher than the theoretical expectation. Measured noise can be split into an uncorrelated component, consistent with shot noise from small energy depositions within the athermal phonon sensor itself, and a correlated component, consistent with shot noise from energy depositions within the silicon substrate's phonon system.

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

The influence of waveguide doping on the output characteristics of AlGaAs/GaAs lasers

The influence of doping of waveguide layers on the output characteristics of lasers based on AlGaAs/GaAs double separate-confinement heterostructures is analysed. The heterostructures with narrow and broadened waveguides are studied. Samples of laser diode bars with undoped and doped waveguide layers are experimentally fabricated and compared. It is shown that the latter type of structures with a broadened waveguide allows one to increase the output power of the laser diode bars by 10 % – 15 %, all other conditions being equal. (lasers. control of laser radiation parameters)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

Leaky wave in high-power AlGaAs/InGaAs/GaAs semiconductor lasers

Lasers based on AlGaAs/InGaAs/GaAs heterostructures operating in the spectral range of 1.0 − 1.1 μm are investigated in order to optimise cladding layers. The effect of the thickness and composition of the cladding layers on the leakage of radiation from the laser waveguide is analysed. It is shown that for cladding thicknesses of 0.86 − 1.24 μm, it almost does not affect the output optical power. The effect of the crystal length and reflectivity of the laser mirrors on the leaky wave is demonstrated. (paper)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2021

Elastic and thermodynamic properties of cerium-doped yttrium aluminum garnets

Cerium-doped yttrium aluminum garnets (Y 3-x Ce x Al 5 O 12 , Ce:YAGs) are promising yellow light-emitting components of solid-state white light-emitting diodes. Although there have been numerous studies examining the effects of Ce concentrations on the luminescent properties of Y 3-x Ce x Al 5 O 12 , the impacts of Ce dopant on the elastic and thermodynamic properties are not well understood. In this work, we used resonant ultrasound spectroscopy (RUS) to determine the effects of Ce doping (0.025, 0.1, 1 at. %) on the elastic and thermodynamic properties of Y 3-x Ce x Al 5 O 12 . The elastic moduli calculated via the Voigt–Reuss–Hill (VRH) method demonstrated that low Ce dopant concentrations (≤0.1 at. %) induced negligible effects on the elasticity of the YAG host matrix, while a high Ce concentration (1 at. %) yielded significant softening. RUS spectral analysis and SEM images suggested that the elastic softening originated from microstructural differences induced at higher Ce dopant concentrations. Additionally, we demonstrated an increase in elastic anisotropy at higher Ce concentrations, which further elucidated the correlations between structure and elasticity of Y 3-x Ce x Al 5 O 12 . Debye temperatures ($θ_D$), heat capacities ($C_p$), and thermal conductivities ($\mathit{κ}$) were calculated for Ce:YAGs through the relations of RUS-derived parameters (sound velocities, elastic moduli) and previously determined thermal expansion coefficients. Ce:YAG was found to have a significant reduction in $θ_D$, Cp, and $\mathit{κ}$ at Ce concentrations ≥1 at. %. Lastly, extrapolation of $C_p$ and $\mathit{κ}$ to higher temperatures allowed the modeling of thermal stress experienced by Y 3-x Ce x Al 5 O 12 disks up to 1073.15 K.

36 MATERIALS SCIENCE↗