Search NASA⌕ Search

SEARCH · Search NASA

Results for “AUSTENITIC STEEL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

Optimization of CCT Equations Using Calculated Grain Boundary Soluble Compositions for the Simulation of Austenite Decomposition of Steels

New CCT equations have been developed and optimized to simulate the start temperatures of the austenite decomposition process in low-alloyed steels using experimental CCT data published in the literature. Exceptionally, this optimization does not apply the nominal compositions of the steels, but the corresponding soluble compositions of the grain boundaries calculated using IDS software, depending on the reported austenitization treatments of the steels. These compositions, rather than the nominal ones, are expected to control the start of the austenite decomposition, which usually initiates at the grain boundaries. The new optimization treatment takes into account the solute microsegregation and the possible precipitate formation. Using IDS software, the new equations were validated with new experimental CCT data. Agreement was good not only for the austenite decomposition start temperatures, but also for the final phase fractions, indicating fairly reasonable predictions of phase transformation kinetics by the IDS. In addition, IDS simulations were compared with the experimental CCT data of five high-carbon steels, applying both the new equations based on grain boundary soluble compositions as well as the equations based on the nominal compositions. With the same experimental CCT data used in optimization, better agreement was obtained with the new equations, indicating the importance of determining the soluble compositions at the grain boundaries where the austenite decomposition process is likely to begin.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Quantifying adherence of oxide scales on steels exposed to high temperature and pressure steam

Oxide scale exfoliation is a major concern in fossil fuel power generation because it can cause tube blockages and erode valves and steam turbine components downstream. There is still considerable scientific and commercial interest to improve the mechanistic understanding of oxide failures by developing models to predict exfoliation and the extent of tube blockage as a function of operating conditions and component geometries. Tensile testing inside a scanning electron microscope was conducted on ferritic–martensitic and austenitic steel specimens with the steam side (Fe,Cr)-rich oxides grown after exposures for up to 1000 h in steam with ~100 ppb O 2 at 276 bar and 550°C. Multiple oxide layer cracks and delamination events were observed and analyzed in detail during the tests. Results from the testing agreed well with earlier observations that had identified the failure location at the outer–inner oxide layer for all tested materials. Calculated adhesion energies identified the outer–inner oxide interface of alloy 347HFG as the weakest interface.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Towards underwater additive manufacturing via additive friction stir deposition

Given the challenges in feed material supply and quality control, metal additive manufacturing has rarely been implemented in austere environments, especially underwater. This paper explores the underwater operation potential of an emerging solid-state additive technology: additive friction stir deposition, wherein material feeding and bonding are enabled by mechanical forces with minimal influences from water. It is demonstrated that additive friction stir deposition of 304 stainless steel can be successfully performed with the print head and substrate immersed in water. High temperature is reached in the deposition zone (>60% melting temperature); the material deposition behavior is similar to that in typical open-air operation. The as-deposited material is fully-dense, having fewer annealing twins and a substantially smaller grain size than the feed material (4.98 μm vs. 31.44 μm ). Such microstructural changes stem from dynamic recrystallization caused by the large strain and high temperature introduced during deposition. In addition to grain refinement, small equiaxed dispersoids (~2–3 μm or less) are formed and evenly distributed in the austenite steel matrix. Rich in Cr, Mn, and O, these particles likely result from the reaction between the elements in stainless steel and water at elevated temperatures.

16 TIDAL AND WAVE POWER↗
DOE OSTI2025

The effect of heat treatment on the defect evolution in LPBF 316H stainless steel

This work investigates the effect of processing and heat treatment on defect evolution and irradiation response of laser powder bed fusion (LPBF) 316H stainless steel, with comparisons to LPBF 316L and wrought 316L/316H. Using in-situ and ex-situ ion irradiations across a wide parameter space—temperature (300–675 °C), dose (0.2–25 dpa), dose rate (10 -3 –10 -5 dpa/s), and helium co-implantation (20–2500 appm)—we correlated void swelling, dislocation loop evolution, and segregation behavior with pre-irradiation microstructures (as-built, stress-relieved, solution-annealed, and cold-worked). Results show that swelling is strongly controlled by dislocation density: intermediate densities maximize swelling, while solution annealing or cold working reduce susceptibility to levels comparable to wrought alloys. Low dose rates and helium both promote cavity nucleation and lower the incubation barrier, with helium suppressing the role of dislocation density and driving swelling behavior toward wrought-like response. Loop evolution in SA LPBF 316H resembles wrought 316L but shows localized denuded zones near low-angle grain boundaries. STEM-EDS mapping further revealed Ni segregation at voids and sparse Al-rich oxides, without evidence of Ni–Si precipitates. Collectively, these findings identify dislocation density, helium content, and dose rate as the factors governing swelling in LPBF 316H and provide mechanistic datasets for model validation, supporting LAIN and the qualification of AM austenitic steels for nuclear service.

316 stainless steel↗
DOE OSTI2022

Assessment of Outliers in Alloy Datasets Using Unsupervised Techniques

We report advancements in data analytics techniques have enabled complex, disparate datasets to be leveraged for alloy design. Identifying outliers in a dataset can reduce noise, identify erroneous and/or anomalous records, prevent overfitting, and improve model assessment and optimization. In this work, two alloy datasets (9-12% Cr ferritic martensitic steels, and austenitic stainless steels) have been assessed for outliers using unsupervised techniques and supplemented with domain knowledge. Principal component analysis and k-means clustering were applied to the data, and points were assessed as outliers based on their distance away from other points in the cluster and from other points in the dataset. The outlier characteristics were investigated to determine both cluster-specific and overall trends in the properties of the outlier points. The approach demonstrated here is extensible to other alloy datasets for outlier identification and evaluation to improve the reliability of machine learning and modeling predictions for advanced alloy design.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Cavity Swelling in Irradiated Materials

Cavity swelling, due to three-dimensional clustering of vacancies, is an undesirable isotropic volume expansion of materials under irradiation. This phenomenon occurs above stage-III recovery temperature where vacancies are mobile, between ~0.3–0.6 Tm where Tm is the absolute melting temperature. The primary mechanism for cavity swelling is “dislocation bias”, i.e., preferential absorption of interstitials by network dislocations, causing a vacancy supersaturation. Cavity swelling is highly temperature dependent and typically follows a bell-shaped curve with peak swelling occurring at an intermediate temperature. With increasing temperature, cavity size increases, and number density decreases logarithmically. With increasing dose, cavity swelling increases, but follows a hockey-stick type pattern, characterized by a low-swelling transient incubation period and then a steady-state regime. The incubation period, dominant in cavity nucleation, is dependent upon material’s chemistry and irradiation conditions such as dose rate/temperature. Cavity swelling increases linearly with dose in the steady-state regime, that is independent of chemistry and dose rate. This regime is dominated by cavity growth. Transmutation gases like He enhance cavity nucleation such that an early onset of cavity formation occurs. However, swelling magnitudes can be either increased or suppressed when He is present. Results in austenitic steels and Cu indicate that cavity swelling peaks at intermediate He/dpa ratios of ~10 appm He/dpa. The most effective method to mitigate cavity swelling is by increasing the fixed point-defect sink density, by promoting precipitation or dispersion strengthening.

Bhattacharya, Arunodaya↗
DOE OSTI2025

Hydrogen charging and desorption from microstructural viewpoint: A method for deconvoluting hydrogen desorption spectra and unveiling the hydrogen-microstructure interaction

Understanding the interaction of hydrogen with microstructural features in metallic materials is crucial for designing hydrogen-resistant alloys. Although thermal desorption spectroscopy (TDS) is widely used for investigating the hydrogen binding behavior of various microstructural features, its application to face-centered cubic (fcc) metals and alloys that exhibit low hydrogen diffusivity is limited due to the lumped TDS desorption signals. This paper shows that, by coupling a Sofronis–McMeeking type hydrogen transport model with a microstructure-informed finite-element model, TDS data can be deconvoluted to reveal the underlying adsorption–diffusion–desorption processes, hydrogen diffusivity, and trap-binding energies. In conclusion, the austenitic steel SS316L in solution-annealed condition is used as a demonstration material, and we focused on investigating the interaction of deuterium (hydrogen isotope) with grain boundaries, which is difficult to investigate from experiments alone but critical for design of alloys for hydrogen infrastructure.

Finite element simulation, Polycrystalline Microst↗
DOE OSTI2026

Evaluation of thermal energy storage for central receiver concentrating solar power plants under charging cycles through structural assessment

Electricity production by concentrated solar power (CSP) systems has stood out among energy transition alternatives due to their large generation capacity (between 30 MW and 400 MW) and high capacity factor (80%) when incorporating thermal storage systems (TES). Although TES tanks in operation worldwide are made of austenitic steels with remarkable mechanical and anticorrosive properties, operational failures have been reported due to low-cycle fatigue, creep, and the abrupt release of residual stresses generated during tank manufacturing. A critical operation for salt tanks is the initial daily charging operation, given the low fluid level and the thermal gradients between the inventory and the salt entering the tank. This study presents a structural simulation of a 39.6 m-diameter molten salt tank for central receiver CSP plants, accounting for temperature and pressure variations during charging and different sparger ring inlet configurations. The initial pre-stressed condition of the floor, resulting from the manufacture of welded plates, is used as a boundary condition. The fatigue and creep life analyses were performed in accordance with the ASME BPVC and API standards. It was found that the tank's floor is in a less favourable mechanical condition than the wall, due to its initial manufacturing condition and the maximum temperature differences during charging. A critical zone was identified in an area affected by residual stress on the floor and under the sparger ring. The baseline sparger ring configuration, with 52 2-inch-diameter orifices and a flow direction of 90 degrees , results in an average floor stress of approximately 25 MPa and creep damage after 1.2 years of tank operation.

14 SOLAR ENERGY↗
DOE OSTI2021

On the computational solution of vector-density based continuum dislocation dynamics models: A comparison of two plastic distortion and stress update algorithms

Continuum dislocation dynamics models of mesoscale plasticity consist of dislocation transport-reaction equations coupled with crystal mechanics equations. The coupling between these two sets of equations is such that dislocation transport gives rise to the evolution of plastic distortion (strain), while the evolution of the latter fixes the stress from which the dislocation velocity field is found via a mobility law. Earlier solutions of these equations employed a staggered solution scheme for the two sets of equations in which the plastic distortion was updated via time integration of its rate, as found from Orowan's law. In this work, we show that such a direct time integration scheme can suffer from accumulation of numerical errors. We introduce an alternative scheme based on field dislocation mechanics that ensures consistency between the plastic distortion and the dislocation content in the crystal. The new scheme is based on calculating the compatible and incompatible parts of the plastic distortion separately, and the incompatible part is calculated from the current dislocation density field. Stress field and dislocation transport calculations were implemented within a finite element based discretization of the governing equations, with the crystal mechanics part solved by a conventional Galerkin method and the dislocation transport equations by the least squares method. A simple test was first performed to show the accuracy of the two schemes for updating the plastic distortion, which shows that the solution method based on field dislocation mechanics is more accurate. This method then was used to simulate an austenitic steel crystal under uniaxial loading and multiple slip conditions. By considering dislocation interactions caused by junctions, a hardening rate similar to discrete dislocation dynamics simulation results was obtained. Finally, the simulations show that dislocations exhibit some self-organized structures as the strain is increased.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Coupling computational thermodynamics with density-function-theory based calculations to design L12 precipitates in Fe Ni based alloys

Achieving a high-volume fraction of thermodynamically stable L12-type precipitates that are resistant to coarsening is of great importance for the development of low-cost FeNi based austenitic steels. With the aid of computational thermodynamics, this work designed two model alloys: Fe-37.4Ni-6.1Al-2.9Ti (FNAT) and Fe-45.2Ni-5.9Al-8.5Si (FNAS). Both alloys were designed to contain a similar amount of L1 2 precipitate in Fe-Ni matrix without forming other precipitates. Density-Function-Theory (DFT) calculation was coupled with computational thermodynamics to predict the critical radius at which the precipitates change shape from spherical to cuboidal. The calculation results suggest that critical radius for the FNAT alloy is about two orders of magnitude larger than that for the FeNiAlSi alloy. Phase stability and morphology of the L1 2 precipitates in these two alloys were experimentally investigated through X-ray diffraction, atom probe tomography, and scanning and transmission electron microscopy. The L1 2 precipitates in the FeNiAlSi system were found to be cuboidal and rod shaped, with much larger size than the spherical ones in the FeNiAlTi system, agreeing with the calculation results. This work suggested that coupling computational thermodynamics with DFT calculations can be reliably used to design L1 2 precipitates in FeNi based alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Radioisotope production at the Spallation Neutron Source: Design concept of isotope production target

Upon completion of the Second Target Station (STS) Project in the mid 2030s, the Spallation Neutron Source accelerator at Oak Ridge National Laboratory will deliver a 2.7 MW proton beam to the neutron production targets. In the post-STS phase, the accelerator will have a reserve beam power capacity of at least 100 kW beyond what the two neutron production targets will receive, which could potentially be ramped up to 300 kW. In this paper, a design concept for a radioisotope production target that could utilize 250 kW of the reserve beam power capacity is presented. The target consists of thorium discs encapsulated in 316L austenitic steel shells that are cooled by water. The estimated post-irradiation activity of Ac-225 and Ra-225, critical medical radioisotopes used in targeted alpha therapy cancer treatment, is calculated at the end of bombardment after a 14 day long irradiation time. Thermal and structural analyses are performed on the basis of calculated nuclear heating data. The technical feasibility of a high-power target under a 250-kW beam load with an extremely low duty factor of $3.5\cdot 10^{-6}$ is presented from thermal, structural and fatigue lifetime perspectives.

Lee, Yong Joong [ORNL] (ORCID:0000000298381723)↗
DOE OSTI2020

Report on FY 2020 creep, fatigue and creep fatigue testing of Alloy 709 base metal at ORNL

The testing activities and research in support of ASME Code qualification of Alloy 709, an advanced austenitic steel, are being carried out at Oak Ridge National Laboratory (ORNL), Argonne National Laboratory, and Idaho National Laboratory. This report summarizes the status and results of FY 2020 planned testing at ORNL. Uniaxial tensile tests on the electroslag remelt (ESR) solution-annealed plate (heat number 58776-3RBC) with additional heat treatment were performed for the baseline mechanical properties evaluation for ASME code qualification of Alloy 709. The tensile properties were found to meet ASME SA-213 specifications and were comparable to the Nippon Steel NF709 data generated for an ASME Section I Code Case for seamless tubing. ORNL was tasked to carry out a subset of the Code Case testing for creep rupture. Creep rupture data from 18 tests were generated on a solution-annealed ESR plate with a solution annealing temperature of 1100°C. There are total of 19 intermediate and long-term creep rupture tests of Alloy 709 ongoing at ORNL. A preliminary fatigue design curve at 760°C was developed for Alloy 709, and the results show that the fatigue design curve of Alloy 709 is comparable to that of Alloy 800H at 760°C.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Creep, Fatigue, and Creep-Fatigue Testing of Alloy 709 Base Metal at ORNL (FY 2021)

The testing activities and research in support of ASME Code qualification of Alloy 709, an advanced austenitic steel, are being carried out at Oak Ridge National Laboratory (ORNL), Argonne National Laboratory, and Idaho National Laboratory. ORNL has been tasked to carry out a subset of the Code Case testing for creep rupture, fatigue and creep-fatigue. The focus of the FY 2021 Code Case testing on Alloy 709 base metal at ORNL includes (1) continuing the long-term creep rupture testing on ESR1100 and AOD1100; (2) adding ESR1150-AH to the creep Code Case testing matrix; and (3) continuing fatigue and creep-fatigue Code Case testing on ESR1150- AH. This report summarizes the status and the preliminary test results of FY 2021 planned Code Case testing at ORNL.

36 MATERIALS SCIENCE↗
DOE OSTI2025

eXtremeMAT: Uncertainty Quantification of the LApx Model

Presentation on the uncertainty quantification efforts to parameterize and fit the LApx model for ferritic-martensitic steels and austenitic stainless steels. These workflows support ease of adoption of the code to new materials and enable rapid model fitting and understanding of the level of confidence in predictions.

mechanical properties↗
DOE OSTI2026

Nondestructive Evaluation of Carbon Fiber Reinforced Polymers

The American Society of Mechanical Engineers Boiler and Pressure Vessel Code requires repair and replacement of safety-related piping materials to meet the original Construction Code; however, no construction criteria currently exist for carbon fiber reinforced polymer (CFRP) materials in the nuclear industry. Although nondestructive examination (NDE) techniques for cast and wrought ferritic and austenitic steels are well established, licensees are increasingly deploying novel materials such as CFRP for which assessment of the use of NDE is required, as the inspectability of such materials and the influence of manufacturing processes on inspectability remain insufficiently understood. To address these gaps, Pacific Northwest National Laboratory (PNNL) evaluated the fabrication of several CFRP repair mockups and the effectiveness of NDE methods to support regulatory review of CFRP repairs in nuclear power plant applications. Representative flat-plate mockups containing realistic fabrication defects were manufactured and inspected using manual and automated tap testing, dynamic response spectroscopy (DRS), and ultrasonic testing (UT). The study identified significant fabrication variability, particularly in controlling defect size and epoxy thickness, which strongly influenced defect detectability by NDE methods. Tap testing was effective for shallow defects in thin epoxy configurations but unreliable for thicker repairs and deeper flaws. DRS demonstrated higher sensitivity to dry spots but produced unconfirmed indications for thicker plates, requiring further validation. Conventional UT, particularly at 1.0 MHz, showed the strongest overall capability for detecting a range of defects, although performance degraded with increasing repair thickness and complexity. The results highlight the need to better define critical defect sizes, develop reliable mockup fabrication methods, and validate NDE methods needed to support CFRP repairs.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Influence of post deposition annealing on the microstructural evolution and tensile behavior of austenitic stainless-steel alloy 709 made by laser powder bed fusion

Structural materials used in the next generation nuclear reactors or other advanced energy systems are often required to withstand higher operating temperatures for a longer service life. Alloy 709 (A709), a Nb-containing and N-stabilized Fe-25Ni-20Cr austenitic stainless steel, has been recommended for high-temperature reactor constructions due to the better performance over the baseline Type 316H stainless steel. Here, in the current manuscript, for the first time, the microstructure evolution and tensile behavior of an A709 made by laser powder bed fusion (LPBF) is discussed. The as deposited and heat treated LPBF alloys are compared with a reference wrought alloy. Owing to the chemical segregation and a higher number of dislocations, the LPBF materials show a significantly higher density of precipitates formed during high temperature treatments when compared to the wrought samples. This is reflected when looking at the tensile properties, both at room and elevated temperatures, where LPBF samples show higher strengths compared to wrought materials.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Effect of nickel on the kinematic stability of retained austenite in carburized bearing steels – In-situ neutron diffraction and crystal plasticity modeling of uniaxial tension tests in AISI 8620, 4320 and 3310 steels

The presence of kinematically metastable retained austenite in the microstructure of bearing components can significantly affect the macro and micro-mechanical material response. In the present work, the influence of Ni on the stability of the retained austenite within three different grades of high carbon bearing steel using in-situ neutron diffraction is investigated. For the first time, the results show that presence of Ni increases the stability of the austenite in the elastic regime whereas the transformation rate remains unaffected. Crystal plasticity finite element (CPFE) modeling was used to study the deformation in these three steels and shows that the predominant factor causing the difference in mechanical behavior of these steels is the austenite stability. Finally, the elastic and plastic response of the matrix martensite was found to be identical among all specimens while the austenite demonstrates similar elastic behavior but remarkably different stabilities under monotonic loading.

36 MATERIALS SCIENCE↗