SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
A membrane-based emulsion separator can enable continuous solvent extraction in bioprocessing separations with substantially improved demulsification and mass transfer rates, including where emulsion formation is a challenge.
A new metalloporphyrin framework of molybdenum Mo 2 O 4 (C 48 H 28 N 4 O 8 )·(CH 3 ) 2 NH·5H 2 O·2DMF (Mo 2 TCPP) was synthesized from tetrakis(4-carboxyphenyl)porphyrin (H 4 TCPP) and sodium molybdate dihydrate by a hydrothermal method. Mo 2 TCPP is a 3D network with two sub-units, in which both TCPP ligands and each Mo 2 dimer act as four connection nodes. The crystal structure was determined by single crystal analysis and further characterized by FTIR, SEM, EDX, PXRD, XPS and TGA. Here cumene hydrogen peroxide and hydrogen peroxide were used as oxidants to study the catalytic activity of new metalloporphyrins in the oxidation of cyclohexene at different temperatures. The conversion rate of cyclohexene and the selectivity of epoxycyclohexane were both higher than 99%, which was better than the previously published research results. The stability of the catalyst before and after the reaction was further tested for 10 runs without obvious degradation. The catalyst was stable in different solutions such as acidic, water and alkaline. These results shed light on the future development of new catalytic materials based on metalloporphyrin.
Carbon mineralization to solid carbonates is one of the reaction pathways that can not only utilize captured CO 2 but also potentially store it in the long term. In this study, the dissolution and carbonation behaviors of alkaline solid wastes (i.e., waste concrete) was investigated. Concrete is one of the main contributors to a large carbon emission in the built environment. Thus, the upcycling of waste concrete via CO 2 utilization has multifaceted environmental benefits including CO 2 emission reduction, waste management and reduced mining. Unlike natural silicate minerals such as olivine and serpentine, alkaline solid wastes including waste concrete are highly reactive, and thus, their dissolution and carbonation behaviors vary significantly. Here, both conventional acid (e.g., hydrochloric acid) and less studied carbonic acid (i.e., CO 2 saturated water) solvent systems were explored to extract Ca from concrete. Non-stoichiometric dissolution behaviors between Ca and Si were confirmed under far-from-equilibrium conditions (0.1 wt% slurry density), and the re-precipitation of the extracted Si was observed at near-equilibrium conditions (5 wt% slurry density), when the Ca extraction was performed at a controlled pH of 3. These experiments, with a wide range of slurry densities, provided valuable insight into Si re-precipitation phenomena and its effect on the mass transfer limitation during concrete dissolution. Next, the use of the partial pressure of CO 2 for the pH swing carbon mineralization process was investigated for concrete, and the results were compared to those of Mg-bearing silicate minerals. In the P CO 2 swing process, the extraction of Ca was significantly limited by the precipitation of the carbonate phase (i.e., calcite), since CO 2 bubbling could not provide a low enough pH condition for concrete–water–CO 2 systems. Furthermore, this study showed that the two-step carbon mineralization via P CO 2 swing, that has been developed for Mg-bearing silicate minerals, may not be viable for highly reactive Ca-bearing silicate materials (e.g., concrete). The precipitated calcium carbonate (PCC) derived from waste concrete via a pH swing process showed very promising results with a high CO 2 utilization potential as an upcycled construction material.
Polylactic acid polymer (PLA) produced from renewable resources can be recycled at the end of life to constituent monomer, optically pure lactic acid (LA), by a combination of chemical and biological processes. Efficient application of this closed loop of LA-PLA plastics-LA can minimize accumulation of plastics waste that pollute land and oceans. Temperature-dependent hydrolysis of PLA in water to LA follows apparent first order decay kinetics after a short lag. A modified Gompertz equation can explain the overall hydrolysis process. Alkali increased the rate of hydrolysis of PLA and reduced the length of lag period compared to water alone. The stoichiometry of base added to LA released was 1.0. The highest lactic acid yield was 0.95 g g -1 of PLA. D-LA in the syrup obtained after hydrolysis of PLA-plastics was removed using an engineered Escherichia coli to produce a L-LA syrup with an optical purity ≥ 99%. Here, these results show that thermochemical hydrolysis of PLA-based plastics to LA with optimum amount of base followed by bio-based purification to L-LA is an effective method of recycling PLA-plastics for reuse.
Organic linkers play a crucial role in constructing lanthanide (Ln) coordination polymers (CPs), influencing structural topologies and physicochemical properties. Herein, we introduce 6-oxo-1,6-dihydro-2,5-pyridinedicarboxylic acid (2,5-H 3 PODC) as a new ligand for constructing lanthanide coordination polymers that integrates the structural features of terephthalic acid with the chelation capabilities of pyridinone-based functional groups. Six lanthanide-based coordination polymers were synthesized with 2,5-H 3 PODC, forming two types of CPs – type 1: [Ln(HPODC)(Ox) 0.5 (H 2 O) 2 ] (where (Ox) = oxalic acid and Ln = Pr 3+ (1), Nd 3+ (2)) and type 2: [Ln(H 2 PODC)(HPODC)(H 2 O)] (Ln = Eu 3+ (3), Gd 3+ (4), Dy 3+ (5), Er 3+ (6)). All compounds were structurally characterized by single-crystal and powder X-ray diffraction, and both compound types are 2D ladder-like networks with cem topologies where the trivalent metal centers are bridged via HPODC 2− and Ox 2− ligands in type 1 structures and H 2 PODC − and HPODC 2− linkers in type 2 structures. Thermogravimetric analysis (TGA) demonstrated that the metal–organic networks of type 1 and type 2 compounds exhibit distinct decomposition patterns, and the photoluminescent properties of 3 were also examined, revealing efficient ligand based sensitization and characteristic emission bands for Eu(III).
Theoretically, single-atom catalysts (SACs) offer 100 % atom utilization, making them strong candidates to replace expensive nanoparticles for catalysis. However, the structural supports used to anchor the SACs dramatically reduce the utilization efficiency of atoms ( i. e ., the percent of atoms actually accessible by reactants) by either encapsulating the SACs completely or creating severe diffusion limitation. Either of which leads to an overall low atom utilization and thus poor electrocatalytic activity similar to that of nanoparticles. In addressing this issue, we systematically investigated how the porous structure of carbon nanospheres affects the activity of Ir-SACs toward formic acid oxidation (FAO). Specifically, we utilized a kinetically-controlled growth strategy to produce uniform carbon nanospheres featuring yolk-shell, mesoporous, and hollow structures with Ir-SACs loaded throughout the structure. At a high specific surface area of 441 m 2 g -1 and exposed metal content of 1.82 wt %, the Ir-SACs based on mesoporous carbon nanospheres showed a remarkable FAO peak current density of 30.6 mA cm -2 , which was 283 and 46 times greater when benchmarked against the catalysts based on solid carbon nanospheres and 20 wt % Ir/C, respectively.
A spectroscopic method was developed for the determination of lignin contents in lignocellulosic biomass, based on a full dissolution of the biomass sample in a cysteine–sulfuric acid solution at room temperature.
The 11th American Conference on Neutron Scattering (ACNS 2022) will be held on June 5-9, 2022, in Boulder, CO. The Conference will provide essential information on the breadth and depth of current neutron-related research worldwide. Hosted by the Neutron Scattering Society of America, this year’s Conference will feature a combination of invited and contributed talks, poster sessions, and tutorials. Topics of the conference are: Advances in Neutron Facilities, Instrumentation and Software: Developments in sources, instrumentation, sample environments and control software. Hard Condensed Matter: Magnetism, correlated metals, quantum/topological materials, superconductors, ferroelectrics, multiferroics, glasses, and disorder phenomena. Submissions outlining examples of neutron scattering in industrial and engineering applications involving hard condensed matter systems are also encouraged. Soft Matter: Neutron studies of soft materials and related fields including in situ and in operando studies. Polymers, surfactants, emulsions, gels, nanoparticles, colloidal suspensions and more. Submissions of computational studies or applications of machine learning beneficial to neutron scattering experiments, as well as examples of neutron scattering in industrial and engineering applications are strongly encouraged. Biology, Biophysics and Biotechnology: Neutron studies of biological and biologically relevant systems. Proteins, bio membranes, biological assemblies, natural materials, nucleic acids, drug-delivery platforms and biomedical systems. Submissions of computational studies or applications of machine learning beneficial to biological neutron scattering experiments, as well as examples of neutron scattering in applied research involving biological systems, are strongly encouraged. Materials Chemistry and Energy: Neutron-based studies of functional materials and materials for energy applications. Examples include porous materials such as metal organic frameworks (MOFs), zeolites; phosphors; novel pigments; electrolytes; catalysts; ionic conductors/cathode materials; photovoltaic materials (hybrid perovskites); thermoelectrics; magnetocalorics/electrocalorics. Structural Materials and Engineering: Neutron scattering studies of materials and engineering processes including structural materials, concrete and metals, as well as engineering processes including combustion, corrosion, additive manufacturing, and others. Neutron Physics: Fundamental physical studies of the neutron and related areas. Emerging Applications in Neutron Scattering: Machine Learning and Data Science: Advances in computing power have contributed to rapidly evolving machine learning and data science fields that can be leveraged to the benefit of the neutron scattering community. The purpose of this session is to highlight recent advances in machine learning and data science and to serve as the foundation of a parallel data and computation track highlighting computation advances and applications in neutron scattering throughout the conference.
Analysis of the MoN, Mo 2 N, VN, Fe 2 N, Fe 4 N, Ni 3 N stability in the aqueous media was performed based on the thermodynamic data available in HSC Chemistry software. Our analysis show that among all the studied nitrides, cubic Mo 2 N is the most resistant while cubic VN is the least resistant to oxidation and decomposition. The change in temperature up to 100 °C does not significantly influence the formation potentials of transition metal oxides from nitrides; however, pH significantly affects the stability of the studied transition metal nitrides. In the case of Mo 2 N, MoN, and VN changing pH from acidic to neutral and alkaline decreases the stability of the nitrides and the oxide formation potentials shift to more negative values. Additionally, based on thermodynamics, orthorhombic Fe 2 N should be stable only in alkaline conditions, while cubic Fe 4 N and hexagonal Ni 3 N should be the most stable at pH ~ 7 and pH ~ 9. Changing pH from these values decreases the stability of both Fe 4 N and Ni 3 N and the formation of oxy-, hydroxy- species becomes thermodynamically more favorable. Overall, the limited stability of the metal nitrides places severe constraints for their use in aqueous electrocatalytic applications.
Solid acid catalysts, including zeolites and amorphous silica-aluminas (ASAs), are industrially important materials widely used in the fuel and petrochemical industries. The versatility of zeolites is due to the Brønsted acidity of the bridging hydroxyl and shape selectivity that can be tailored during and after synthesis. This is in contrast to amorphous silica-alumina, where tailoring acidity is a major challenge as the Brønsted acid structure in ASA is still debated. In both cases, however, the pore size and acidity cannot be tuned independently, and this is particularly limiting in the application of biomass conversion, where zeolite pores are too small for the molecules of interest. Herein, we present a method using atomic layer deposition (ALD) to prepare thin films of solid acid materials where the ratio of Brønsted to Lewis acid sites can be tuned precisely. This capability, combined with the sub-nm pore size control afforded by ALD yields a powerful and flexible method for synthesizing solid acid catalysts inside virtually any mesoporous host. We demonstrate the utility of these materials in two acid-catalyzed reactions relevant to biomass conversion: (1) Meerwein–Ponndorf–Verley–Oppenauer (MPVO) reaction and dehydration of fructose and (2) cascade reaction of glucose to 5-hydroxymethylfurfural. Finally, we propose a plausible structure for the Brønsted acid sites in our materials based on infrared spectroscopy and solid-state nuclear magnetic resonance measurements and density functional theory calculations and argue that this same structure might apply to conventional ASAs as well.
Atmospheric perturbations caused by the emission of nitrogen oxides from a projected fleet of stratospheric aircraft are studied with a two dimensional chemistry, transport model. Photochemistry of the lower stratosphere, the region where these aircraft may fly, is now known to be influenced by heterogeneous reactions involving sulfuric acid aerosols. This study examines the sensitivity of the atmospheric effects of aircraft to heterogeneous reactions. Information of background aerosols based on the SAGE 2 measurements have been used in the parameterization of the heterogeneous conversion rates. It is found that heterogeneous reactions make the lower stratospheric ozone less sensitive to perturbations in the odd nitrogen level. The calculated reduction in global ozone due to NO(x) injection from a fleet of Mach 2.4 aircraft is 1.28 percent if gas phase reactions only are considered in the model, and 0.06 percent if heterogeneous reactions are included.
The polymerization of ribonucleic acids or their precursors constitutes an important event in prebiotic chemistry. The various problems using ribonucleotides to make RNA suggest that there may have been a precursor. An attractive possibility are the peptide nucleic acids (PNA). PNAs are nucleotide analogs that make use of a polymer of ethylenediamine monoacetic acid (EDMA or 2-amninoethyl glycine) with the bases attached by an acetic acid. EDMA is an especially attractive alternative to the ribose phosphate or deoxyribose phosphate backbone because it contains no chiral centers and is potentially prebiotic, but there is no reported prebiotic synthesis. We have synthesized both EDMA and ethylenediamine diacetic acid (EDDA) from the prebiotic compounds ethylenediamine, formaldehyde, and hydrogen cyanide. The yields of EDMA range from 11 to 79% along with some sEDDA and uEDDA. These reactions work with concentrations of 10(exp -1)M and as low as 10(exp -4)M, and the reaction is likely to be effective at even lower concentrations. Ethylenediamine is a likely prebiotic compound, but it has not yet been demonstrated, although compounds such as ethanolamine and cysteamine have been proven to be prebiotic. Under neutral pH and heating at l00 C, EDMA is converted to the lactam, monoketopiperazine (MKP). The cyclization occurs and has an approximate ratio of MKP/EDMA = 3 at equilibrium. We have measured the solubilities of EDMA center dot H20 as 6.4 m, EDMA center dot HCl center dot H20 as 13.7 m, and EDMA center dot 2HCl center dot H20 as 3.4 m. These syntheses together with the high solubility of EDMA suggest that EDMA would concentrate in drying lagoons and might efficiently form polymers. Given the instability of ribose and the poor polymerizability of nucleotides, the prebiotic presence of EDMA and the possibility of its polymerization raises the possibility that PNAs are the progenitors of present day nucleic acids. A pre-RNA world may have existed in which PNAs or polymers with related peptide backbones were the dominant information macromolecules.
Here, metal-organic framework-808 has been functionalized with 11 amino acids (AA) to produce a series of MOF-808-AA structures. The adsorption of CO 2 under flue gas conditions revealed that glycine- and DL-lysine-functionalized MOF-808 (MOF-808-Gly and -DL-Lys) have the highest uptake capacities. Enhanced CO 2 capture performance in the presence of water was observed and studied using single-component sorption isotherms, CO 2 /H 2 O binary isotherm, and dynamic breakthrough measurements. The key to the favorable performance was uncovered by deciphering the mechanism of CO 2 capture in the pores and attributed to the formation of bicarbonate as evidenced by 13 C and 15 N solid-state nuclear magnetic resonance spectroscopy studies. Based on these results, we examined the performance of MOF-808-Gly in simulated coal flue gas conditions and found that it is possible to capture and release CO 2 by vacuum swing adsorption. MOF-808-Gly was cycled at least 80 times with full retention of performance. This study significantly advances our understanding of CO 2 chemistry in MOFs by revealing how strongly bound amine moieties to the MOF backbone create the chemistry and environment within the pores, leading to the binding and release of CO 2 under mild conditions without application of heat.
The rapid growth and plummeting cost of solar energy have spurred growing interest in using CO 2 electrolysis to produce chemicals and fuels as an alternative to conventional petrochemical processes. High-temperature (>800 °C) solid oxide electrolyzers that convert CO 2 into CO and O 2 have recently become commercially available. Low-temperature electrolysis cells offer the prospect of more convenient and flexible operation, which is critical for utilizing intermittent solar energy, and provide access to more valuable C 2+ products such as ethylene, ethanol, and propanol. Over the past 10 years, research in this area has yielded substantial progress in both fundamental understanding of the requisite electrocatalytic reactions and design of prototype devices. Leveraging insights from fuel cells and membrane water electrolyzers, researchers have developed electrolysis cells with gas diffusion electrodes (GDE) that have demonstrated high CO 2 electrolysis current densities (>100 mA cm –2 ) as well as promising selectivity and stability. Despite these advances, the energy efficiency (electrical energy-to-product) and carbon efficiency (CO 2 -to-product) of low-temperature CO 2 electrolysis remain far too low for large-scale deployment. A preponderance of evidence indicates that the principal source of efficiency losses is the rapid and thermodynamically favorable reaction of CO 2 with hydroxide (OH – ) to form carbonate (CO 3 2– ). Carbonate formation imposes steady-state electrolysis conditions that result in large voltage and CO 2 losses for all known (photo)electrochemical CO 2 cells. While much current research remains focused on CO 2 reduction catalyst design, this largely overlooked CO 3 2– problem presents a fundamental scientific barrier to creating a viable electrochemical option for converting solar energy into chemicals and fuels. The project pursues an integrated, multi-PI research effort that establishes a fundamental science of CO 3 2– management. PI Kanan and Co-PI Mani’s contribution to the project is to evaluate strategies to mitigate the CO 3 2– problem by changing the properties of the electrolyte and the environment in which CO 2 reduction catalysis takes place. Experimental studies showed that electrolytes composed of a high concentration of both CO 3 2– and HCO 3 – , which serve as moderately alkaline buffers, improved the cell voltage by compared to all-HCO 3 – electrolytes, but these buffered systems still show substantial CO 2 uptake that reduces pH over time. Computational studies developed a homogenized model of a CO 2 reduction catalyst layer that permits a low-cost exploration of the high-dimensional parameter space associated with catalyst layers on gas diffusion electrodes. The model was validated by accurately reproducing experimental data for the related but simpler reaction of CO reduction and then used to probe the effects of catalyst layer architecture on CO 2 reduction. Minimizing the size of catalyst and hydrophobic domains in the catalyst layer is predicted to mitigate CO 3 2– formation and thereby enable prolonged operation at elevated pH. In support of the CO 2 electrolysis studies, a new method for rapidly prototyping electrochemical cells was developed and validated. The method uses a combination of 3D printing and electroless plating to generate conductive cell components for evaluating new cell designs. The carbonate problem encompasses mass transport processes and acid-base reactions that are relevant to many other electrochemical systems. Investigation of strategies to address the carbonate problem led to an additional line of inquiry into the physicochemical phenomena that determine the efficiency of electrochemical acid-base production, which has numerous applications in the broader field of carbon management. New strategies for using the supporting electrolyte to inhibit H + /OH – recombination in electrochemical acid-base production were evaluated, leading to the development of a novel acid-base producing system that eliminates the need for ion exchange membranes and exhibits promising efficiency and current densities for scalable applications.
Explore the source record for details and available documents.
It is found that the thermal expansion behaviors are highly dependent on the framework topologies for indium biphenyl tetracarboxylate based MOFs.
Not Available
The hazards of non-polysaccharide materials in a transuranic (TRU) waste drum exposed to nitric acid (HNO 3 ) and metal nitrate salts have been evaluated, focusing on sorbents and on resins used in ion-exchange chromatography. The range of sorbent materials can be grouped into two general categories: 1) a variety of polyacrylate and polyacrylamide compounds that incorporate polar carbonyl functional groups designed to sorb protic (i.e., acidic) substrates and solutions; 2) hydrocarbon based polymers that include polystyrene, polybutadiene, and polyethylene derivatives, which are designed to sorb non-polar organic substrates and solutions. The ion-exchange resins are constructed of hydrocarbon based polymeric networks equipped with pendant ionizable functional groups designed to reversibly sorb/desorb ionic species that are targeted for separation from a mobile phase.