Search NASA⌕ Search

SEARCH · Search NASA

Results for “Air mass”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Deliquescence of Eutectic LiCl-KCl Diluted with NaCl for Interim Waste Salt Storage

Molten eutectic LiCl-KCl salt is a widely used electrolyte for electrorefining uranium from spent nuclear fuel. Due to the hygroscopic nature of this salt, such operations must be performed under controlled atmospheric conditions, and waste salts require careful storage to avoid deliquescence and corrosion of container materials. This study investigated a potential processing path for reducing the degree of deliquescence through dilution to varying extents with NaCl. Here, the hydration behavior of LiCl-KCl salts diluted with NaCl was evaluated in terms of mass gain due to water absorption, degree of deliquescence (including first appearances of standing water), and evidence of corrosion to stainless steel containers in a humid air environment (40°C, 20% relative humidity). In this humid air environment, pure eutectic LiCl-KCl exhibited a 50 mass % increase due to water absorption and showed evidence of standing water after 24 h. Waste salt diluted with NaCl required loadings of 89 mass % NaCl in order to prevent deliquescence and exhibited a 3 mass % increase due to water absorption. After periodic observation for 48 h, standing water was observed near all ingots with the exception of the 89 mass % NaCl samples. Dilution with 89% NaCl was also found to reduce evidence of corrosion when stored in stainless steel crucibles. While dilution with NaCl greatly decreases steady-state hydration, the storage volume is increased ~10× through this procedure.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

An analysis of the hybrid internal mass modeling approach in EnergyPlus

Accurate simulation of building system dynamics is particularly important for understanding building energy flexibility. Among all dynamics in a building, a zone temperature’s variation is especially important, as it significantly affects a building’s electricity load profile when its heating, ventilating, and air conditioning (HVAC) system is controlled with on/off cycles or setpoint reset strategies. To accurately simulate a zone temperature’s dynamics, internal mass needs to be modeled carefully. In this paper, we compare the two internal mass modeling approaches provided by EnergyPlus, i.e., internal mass object and zone air capacitance multiplier, to better understand their impacts on zone temperature simulation. Real building zone temperature dynamic data from small- and medium-sized office buildings are analyzed and compared with simulated data. In particular, we illustrate the effectiveness of a hybrid method of the two EnergyPlus modeling approaches, which yields more realistic zone temperature dynamics, especially when the zone is conditioned with heat pump systems with on/off cycling.

Chen, Zhelun↗
DOE OSTI2025

Air-sea interactions yielding rapid Beaufort Sea ice losses during the 2021 ONR THINICE Pilot Field Campaign

Seasonal sea ice coverage has declined in the Pacific Arctic region. Losses of the ice cover have modified the region’s surface heat and momentum fluxes providing weather systems more direct interaction with the upper ocean. For example, recent cyclones that have passed over these waters have initiated multiple air-sea interactions and have impacted mixed layer depth, wave properties, and sea ice mass budgets due to diabatic and/or advective processes. As a United States Office of Naval Research (ONR) Departmental Research initiative, one key component of the ONR THINICE program was to advance knowledge on Arctic cyclone coupling with the ocean surface, its ice cover, and understand how such coupling can lead to rapid ice loss. Leading up to the primary field campaign in August 2022, a pilot field campaign from 19 August to 13 September 2021 focused in Utqiagvik, Alaska and Longyearbyen, Svalbard was carried out. This period was marked by frequent Arctic cyclones, periods of strong low-level winds, and stints of extreme short-term Beaufort Sea ice area losses. Cyclones traversed these waters much more frequently than usual during this 26-day period, but did not exhibit extreme central pressures indicative of high intensity and impactful storms. Using ERA5 atmospheric reanalysis fields, CERES and AIRS surface flux retrievals, and in situ sensor data collected from ice-tethered profilers and ice mass balance buoys, we highlight air-sea-ice interactions in the Beaufort Sea during and between these cyclones leading up to extreme ice loss events. Our case study analysis is aimed at understanding how Arctic cyclones, including air-sea interactions prompted by their passage over the marginal ice zone, influence the end-of-summer ice conditions and ice loss events. This study provides an example where frequent, yet weak storms drive rather large marginal sea-scale losses albeit with heterogenous sea ice effects at local scales.

Ballinger, Thomas [International Arctic Research C↗
DOE OSTI2022

Impact of Tree Age and Anatomical Fraction on Forest Residue Pyrolysis and Hydrotreating

Utilization of cost-advantaged biomass and waste resources to produce clean, domestic biofuels will be a key factor in decarbonizing transportation in the United States. This study investigates how the distribution of anatomical fractions (stem wood, bark, needles, branches) from pine forest residues of different ages impacts pyrolysis and hydrotreating processes, including product composition, carbon efficiency, economics, and overall sustainability. Commercially sourced 13- and 23-year-old loblolly pine residues were chosen to represent available resources; whole tree thinnings, and tops and branches from merchantable timber, respectively. Detailed characterization of the residue samples, product distributions, bio-oil, char, and gas characterization data are presented for 13 experiments, including the individual fractions, blends, and air-classified samples to reduce ash content. Pyrolysis mass balances averaged 97 +/- 3%. As expected, bio-oil yields were lower for the bark, needles, and blends with high proportions of these (53-56% dry basis), and highest for the debarked stem wood (67-71% dry basis). Lower yields were attributed to the high ash content of the needles, but also to the high lignin content in the bark (>50%), which is hypothesized to have led to increased char formation during pyrolysis. Higher-oil yield was generally correlated with total volatiles, hydrogen, oxygen, glucan, and mannan; somewhat correlated with xylan and acetyl content; and negatively correlated with total carbon, fixed carbon, nitrogen, sulfur, and extractives. Air classification of the residues was effective in reducing ash content (1.5% to 0.64%), extractives (~7% to 2%), and sulfur (0.04% to 0.02%), resulting in a small increase in yield, a significant increase in the GC-detectable proportion of oil (27% to 34%) and a net economic benefit. These experimental results were used to conduct technoeconomic and life cycle analyses, which are also summarized here.

biofuels↗
DOE OSTI2023

Impacts of a Prescribed Fire on Air Quality in Central New Mexico

A short-duration but high-impact air quality event occurred on 28 November 2018 along the Rio Grande Valley of New Mexico. This fire occurred outside the typical wildfire season, and greatly impacted the air quality in Socorro, NM, and the surroundings. Measurements were taken during the event using an aerosol light scattering technique (integrating nephelometer) and a particulate mass concentration monitor (DustTrak PM optical monitor). The instruments sampled the ambient air during the event on the campus of the New Mexico Institute of Mining and Technology in Socorro, New Mexico. The peak values on a 5-min basis of light scattering and the PM mass concentration reached 470 Mm -1 and 270 µg/m 3 , respectively. We examined the meteorological context of the event using local meteorological data and back trajectories using the NOAA HYSPLIT model to determine atmospheric transport and possible sources. Several fires, both prescribed and wildfires, occurred in the region including a prescribed burn at Bosque del Apache National Wildlife Refuge (17 km south-southeast of the receptor site). The data suggest that the prescribed burn at Bosque del Apache was the dominant contributor due to transport evidence and the event’s narrow spatiotemporal extent. The increasing importance of restoring ecosystem function using prescribed fire in wildland fire management will likely lead to more frequent air quality impacts and sets up policy tradeoffs that require a balance between these public goals. This study examines the evidence of the effects of a prescribed fire in a protected wildland area impacting the air quality in a nearby populated area.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Separation of volatile organic contaminants from water using a direct-contact dehumidifier: An experimental study and modeling

A packed-bed, direct-contact dehumidifier (PB-DCD) has been developed to selectively condense water from a gaseous mixture of organic contaminants. In this process, hot air is humidified by mixing with wastewater vapor in a static mixer and is dehumidified by subcooled fresh water passing through the PB-DCD in a counter-current configuration. The goal of this study is to understand the relationship between various operating parameters and how they affect separation of isopropyl alcohol (IPA) from the gaseous mixture with the purpose of expanding the investigation to other contaminants in the future. The process has been successfully used to separate IPA from wastewater. Different parameters including the concentration of IPA in water, feed temperature, air-to-vapor ratio, and cooling-water-to-vapor mass ratio, as well as residence time were examined to determine their influence on contaminant separation and clean water recovery rate. The Buckingham Pi theorem was applied to reduce the number of studying variables by generating non-dimensional groups. Experiments were performed to determine the relationship between the non-dimensional parameters and model mass transfer in the system. Mass transfer coefficients for multicomponent gaseous mixture condensation in a packed-bed direct contact condenser column are calculated and a modified correlation of mass transfer is developed. The parameters of the mass transfer model are obtained from operating conditions of the PB-DCD, stream conditions and thermodynamic properties. A modified Sherwood correlation is developed to predict IPA separation from a gaseous mixture consisting of air, water, and IPA. The modified Sherwood correlation is applied to successfully predict the Sherwood number with a mean absolute error equal to 6.6 %. According to the experimental results, the maximum IPA separation achieved was 76.3 %, which corresponds to a water recovery rate of 58.7 %.

42 ENGINEERING↗
DOE OSTI2021

ORNL FACE Final Harvest, 2009, with data on leaf characteristics and tree mass

During the final year of the Oak Ridge National Laboratory (ORNL) free-air CO2 enrichment (FACE) experiment, 16 trees were felled and processed during July 2009. The trees had been grown for 12 years in ambient or elevated CO2. Two data sets are reported. Leaf characteristics (leaf mass per unit area, leaf thickness, average leaf size, carbon and nitrogen concentrations) are reported for each 1-meter section of the tree crowns in data set "Canopy_subsamples.csv". The measurements were made on approximately 20 subsamples collected from each 1-meter section of the canopy. Wood dry mass, total tree height, basal area, total leaf mass and leaf area are reported in "Tree_harvest.csv", based on field measurements of fresh mass and dry mass to fresh mass ratio of subsamples. The ORNL FACE experiment, including photos of the harvesting activity, is described at: https://richnorby.org/home/face-home/.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Volatile aldehyde emissions from “sub-ohm” vaping devices

"Sub-ohm" atomizers with reduced resistance can deliver more power than conventional electronic cigarettes. Typical battery outputs are 100 watts or more. These devices are particularly popular among young users, and can be a significant source of volatile carbonyls in the indoor environment. Emissions from next-generation sub-ohm vaping products were characterized by determining e-liquid consumption and volatile aldehydes emissions for several combinations of popular high-power configurations. Tests explored the effect of dilution air flow (air vent opening), puffing volume, and coil assembly configuration. The mass of liquid consumed per puff increased as the puff volume increased from 50 to 100 mL, then remained relatively constant for larger puff volumes up to 500 mL. This is likely due to mass transfer limitations at the wick and coil assembly, which reduced the vaporization rate at higher puff volumes. Carbonyl emission rates were systematically evaluated using a 0.15 Ω dual coil atomizer as a function of the puffing volume and dilution air flow, adjusted by setting the air vents to either 100% (fully open), 50%, 25%, or 0% (closed). The highest formaldehyde emissions were observed for the lowest puff volume (50 mL) when the vents 31 were closed (48 ng mg-1), opened at 25% (39 ng mg -1 ) and at 50% (32 ng mg -1 ).. By contrast, 50-mL puffs with 100% open vents, and puff volumes >100 mL for any vent aperture, generated formaldehyde yields of 20 ng mg -1 or lower, suggesting that a significant cooling effect resulted in limited carbonyl formation. Considering the effect of the coil resistance when operated at a voltage of 3.8 V, the amount of liquid evaporated per puff decreased as the resistance increased, in the order of 0.15 Ω > 0.25 Ω > 0.6 Ω consistent with decreasing aerosol temperatures measured at the mouthpiece. Three different configurations of 0.15 Ω coils (dual, quadruple and octuple) were evaluated, observing significant variability. No clear trend was found between carbonyl emission rates and coil resistance or configuration, with highest emissions corresponding to a 0.25 Ω dual coil atomizer. Carbonyl emission rates were compared with those determined using the same methodology for conventional e-cigarettes (lower power tank systems), observing overall lower yields for the sub-ohm devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

NETL Mobile Emissions Laboratory

This presentation was given (virtually) at the workshop on Atmospheric Chemistry and Dispersion Modelling of Non-CO2 Emissions from Carbon Capture at the National Carbon Capture Center on November 21, 2024. The presentation describes capabilities of NETL's new mobile emissions laboratory trailer.

air emissions↗
DOE OSTI2025

SCILLA mini-Aerosol Mass Spectrometer (mAMS) airborne data

Measurements of non-refractory, sub-micron aerosol composition, namely organic, sulfate, nitrate, chloride, and ammonium aerosols, by a mini- aerosol mass spectrometer (mAMS, Aerodyne Research, Inc.) are reported. The instrument sampled ambient air through 3 different inlets: unperturbed ambient air, a Counter-flow Virtual Impactor (CVI), and an oxidation flow reactor (OFR). Users should consult the Sampling Key for proper interpretation of the data.

and secondary aerosol in air",total_organics,nitra↗
DOE OSTI2022

Assessing mass balance-based inverse modeling methods via a pseudo-observation test to constrain NO x emissions over South Korea

This study constrains NO x emissions by utilizing mass balance–based inverse modeling methods and examines the optimization of inverse modeling conditions through a pseudo-observation test for South Korea, which has complex topography. Here, we applied mass balance–based inverse modeling methods such as Basic Mass Balance (BMB), Finite Difference Mass Balance (FDMB), and Iterative Finite Difference Mass Balance (IFDMB). We performed a numerical simulation of air quality using the Community Multi-scale Air Quality (CMAQ) model to calculate the NO 2 column density required for the inverse modeling. The pseudo-observation test was performed according to season, modeling resolution, and regridding methodology of satellite observation data to identify various conditions while applying the inverse modeling for South Korea. Comparing the inverse modeling results from the BMB, FDMB, and IFDMB methods, IFDMB was the most effective method in constraining NO x emissions in the South Korean region since it minimized smearing effects (i.e., transport-induced errors) through iterative calculations. The accuracy of the constrained NO x emissions using mass balance–based inversions in South Korea was the highest in the summer due to the minimized smearing effects, and the 9 km resolution modeling was the most efficient for inverse modeling of the region. In addition, the results of inverse modeling varied depending on the regridding methods, implying the importance of using a suitable regridding method and modeling resolution. This study used pseudo-observations, but the inversions are expected to be applied based on actual satellite data in the future.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Molecular Characterization of Organosulfate-Dominated Aerosols over Agricultural Fields from the Southern Great Plains by High-Resolution Mass Spectrometry

The molecular composition of organic aerosols, especially for day/nighttime variations of organosulfates above agricultural fields, is not well understood despite profound impacts on regional climate, crop production, air quality, and human health. Here, nanospray desorption electrospray ionization with high-resolution mass spectrometry (nano-DESI-HRMS) is used to interrogate the molecular composition of organic aerosols collected at the Southern Great Plains, located in an agricultural region of Oklahoma. Identified molecular formulae featured carbon, hydrogen, oxygen (CHO), nitrogen (CHNO), and/or sulfur (CHOS, CHNOS), with higher organosulfate proportions during daytime (41%) compared to nighttime (30%). In this work, nighttime aerosols featured increases in CHO, CHNO, and extremely low volatility organic carbon (ELVOC) species. However, due to high relative humidity, the nighttime aerosols phase state was found to be more liquid-like than daytime aerosols using parametrized glass transition temperatures. Aerosol molecular composition from an anthropogenically influenced plume (southerly winds) showed significant increases in CHOS and ELVOC species. By comparison with chamber studies, CHOS species are suspected to be of mixed biogenic and anthropogenic origin, whereas CHNOS species (not identified in the southerly winds) are suggested to predominately be of biogenic origin. Overall, this study provides key insight into organosulfates above agricultural fields, demonstrating dependence upon day/night cycles and episodic anthropogenic emissions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Thermal Properties of Sodium Borosilicate Glasses as a Function of Sulfur Content

SO3 additions, up to 3.0 wt%, were systematically investigated for effects on the physical properties of sodium borosilicate glass melted in air, with a sulfur-free composition of 50SiO2-10Al2O3-12B2O3-21Na2O-7CaO (wt%). Solubility measurements, using electron microscopy chemical analysis, determined the maximum loading to be ~1.5 wt% SO3. It was found that sulfur (here as sulfate) in this glass increased the glass transition temperature, thermal diffusivity, heat capacity, and thermal conductivity, and decreased the mass density. Structural analysis, performed with Raman spectroscopy, indicated that the borosilicate network polymerized with sulfur additions, presumably due to Na2O being required to charge compensate the ionic SO42- additions, thus becoming unavailable to form non-bridging oxygen in the silicate network. It is postulated that this increased crosslinking of the borosilicate backbone lead to a structure with higher dimensionality and average bond energy. This increased the mean free paths and vibration frequency of the phonons, which resulted in the observed increase in thermal properties.

Thermal properties, Borosilicate glass, Sulfur sol↗
DOE OSTI2024

High energy density picoliter-scale zinc-air microbatteries for colloidal robotics

The recent interest in microscopic autonomous systems, including microrobots, colloidal state machines, and smart dust, has created a need for microscale energy storage and harvesting. However, macroscopic materials for energy storage have noted incompatibilities with microfabrication techniques, creating substantial challenges to realizing microscale energy systems. Here, we photolithographically patterned a microscale zinc/platinum/SU-8 system to generate the highest energy density microbattery at the picoliter (10 −12 liter) scale. The device scavenges ambient or solution-dissolved oxygen for a zinc oxidation reaction, achieving an energy density ranging from 760 to 1070 watt-hours per liter at scales below 100 micrometers lateral and 2 micrometers thickness in size. The parallel nature of photolithography processes allows 10,000 devices per wafer to be released into solution as colloids with energy stored on board. Within a volume of only 2 picoliters each, these primary microbatteries can deliver open circuit voltages of 1.05 ± 0.12 volts, with total energies ranging from 5.5 ± 0.3 to 7.7 ± 1.0 microjoules and a maximum power near 2.7 nanowatts. We demonstrated that such systems can reliably power a micrometer-sized memristor circuit, providing access to nonvolatile memory. We also cycled power to drive the reversible bending of microscale bimorph actuators at 0.05 hertz for mechanical functions of colloidal robots. Additional capabilities, such as powering two distinct nanosensor types and a clock circuit, were also demonstrated. The high energy density, low volume, and simple configuration promise the mass fabrication and adoption of such picoliter zinc-air batteries for micrometer-scale, colloidal robotics with autonomous functions.

Robotics↗
DOE OSTI2021

Studying Interfacial Dark Reactions of Glyoxal and Hydrogen Peroxide Using Vacuum Ultraviolet Single Photon Ionization Mass Spectrometry

Aqueous secondary organic aerosol (aqSOA) formation from volatile and semivolatile organic compounds at the air–liquid interface is considered as an important source of fine particles in the atmosphere. However, due to the lack of in situ detecting techniques, the detailed interfacial reaction mechanism and dynamics still remain uncertain. In this study, synchrotron-based vacuum ultraviolet single-photon ionization mass spectrometry (VUV SPI-MS) was coupled with the System for Analysis at the Liquid Vacuum Interface (SALVI) to investigate glyoxal dark oxidation products at the aqueous surface. Mass spectral analysis and determination of appearance energies (AEs) suggest that the main products of glyoxal dark interfacial aging are carboxylic acid related oligomers. Furthermore, the VUV SPI-MS results were compared and validated against those of in situ liquid time-of-flight secondary ion mass spectrometry (ToF-SIMS). The reaction mechanisms of the dark glyoxal interfacial oxidation, obtained using two different approaches, indicate that differences in ionization and instrument operation principles could contribute to their abilities to detect different oligomers. Therefore, the mechanistic differences revealed between the VUV SPI-MS and ToF-SIMS indicate that more in situ and real-time techniques are needed to investigate the contribution of the air–liquid interfacial reactions leading to aqSOA formation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Vacuum-Healing of Grain Boundaries in Sodium-Doped CuInSe 2 Solar Cell Absorbers

Alkali metal doping and grain boundaries (GB) have been at the center of attention within the Cu(In,Ga)(S,Se) 2 photovoltaics community for years. This study provides the first experimental evidence that the GB of sodium-doped CuInSe 2 thin films may undertake reversible oxidation even at room temperature, whereas undoped films may not. The findings are corroborated by cathodoluminescence imaging, secondary ion mass spectrometry, and Kelvin probe force microscopy on air-exposed films subsequently subject to vacuum. A thermochemical assessment identifies the likely solid-gas equilibria involved. These reactions open new research questions with respect to the beneficial role played by alkali metal dopants in chalcopyrite solar cells and may steer the community toward new breakthroughs.

14 SOLAR ENERGY↗
DOE OSTI2021

Plastic waste upcycling toward a circular economy

Large amounts of plastics are discarded worldwide each year, leading to a significant mass of waste in landfills and pollution to soil, air, and waterways. Upcycling is an efficient way to transform plastic waste into high-value products and can significantly lessen the environmental impact of plastic production/consumption. In this article, current advances and future directions in plastic waste upcycling technologies are discussed. In particular, this review focuses on the production of high-value materials from plastic waste conversion methods, including pyrolysis, gasification, photoreforming, and mechanical reprocessing. Plastic waste compositions, conversion products, reaction mechanisms, catalyst selection, conversion efficiencies, polymer design, and polymer modification are also explored. Furthermore, the main challenges facing the adoption and scale-up of these technologies are highlighted. Suggestions are given for focusing future research and development to increase the efficiency of upcycling practices.

30 DIRECT ENERGY CONVERSION↗