Search NASA⌕ Search

SEARCH · Search NASA

Results for “Airframes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Airframe noise of a small model transport aircraft and scaling effects

Airframe noise of a 0.01 scale model Boeing 747 wide-body transport was measured in the Langley Anechoic Noise Facility. The model geometry simulated the landing and cruise configurations. The model noise was found to be similar in noise characteristics to that possessed by a 0.03 scale model 747. The 0.01 scale model noise data scaled to within 3 dB of full scale data using the same scaling relationships as that used to scale the 0.03 scale model noise data. The model noise data are compared with full scale noise data, where the full scale data are calculated using the NASA aircraft noise prediction program.

Shearin, J. G.↗
NASA NTRS1980

Design, fabrication and test of a complex helicopter airframe section

A design solution is developed for the fabrication of an all-composite helicopter airframe cabin roof structure. Although this is inherently a complex structure, the parts count has been minimized by the avoidance of many mechanical fasteners, and a weight reduction of 26% has been obtained. The reduction of parts and elimination of mechanical fasteners will also result in a lowering of labor costs. The bonded graphite/epoxy elements of the structure employed aluminum tooling with control on all mating surfaces to yield accurate bond lines. A summary of static test results is presented for the basic structure and for the structure with mechanically fastened skin stiffeners. It is shown that the shear buckles caused the skin to peel from the stiffeners at about 960 lb/in. shear flow, calling for the addition of stiffeners with more bond area.

Rich, M. J.↗
NASA NTRS1981

Predicted airframe noise levels for certification flights

A correction is presented for a previously published inconsistency in predicted airframe noise values, which were based on approach velocities lower than those required for FAA certification. New figures are given for the following aircraft: DC-9-30, 727-200, A300-B2, L-1011, DC-10-10, and 747-200B. The new levels average 2.3 dB higher than those calculated for typical approach speeds.

Block, P. J. W.↗
NASA NTRS1981

Prediction of jet exhaust noise on airframe surfaces during flight

The behavior of pressure fluctuations measured on the airframe of a prototype high lift jet transport (YC-14) is presented. The data are characterized in terms of a particular jet exhaust flow field idealization, jet mixing noise, and exhaust shock noise. Generalized spectrum shapes and scaling relations for peak level and frequency of peak level are developed, and the frequency is found to depend on jet exhaust velocity and aircraft velocity. Comparisons are made with near-field engine exhaust noise of a conventional jet, and results suggest that the same two exhaust noises are important for both aircraft types. Surface fluctuating pressure data are assessed, and results suggest that the jet mixing and exhaust shock noise source characterizations for the YC-14 have useful applicability to conventionally configured jets.

Butzel, L. M.↗
NASA NTRS1981

Airframe-propulsion system aerodynamic interference predictions at high transonic Mach numbers including off-design engine airflow effects

The transonic speed regime for airplanes at conditions where inlet spillage takes place is discussed. A wind tunnel test program to evaluate aerodynamic performance penalties associated with propulsion system installation and operation at subsonic through low supersonic speeds was conducted. The accuracy of analytic methods for predicting transonic engine airframe interference effects was assessed. Study variables included Mach number, angle of attack, relative nacelle location, and nacelle mass flow ratio. Results include test theory comparisons of forces as well as induced pressure fields. Prediction capability of induced shock wave strength and locations is assessed. It was found that large interference forces due to engine location and flow spillage occur at transonic speeds, that theory explains these effects; and that theory can predict quantitatively these effects.

Kulfan, R. M.↗
NASA NTRS1982

Integrated airframe propulsion control

Perturbation equations which describe flight dynamics and engine operation about a given operating point are combined to form an integrated aircraft/propulsion system model. Included in the model are the dependence of aerodynamic coefficients upon atmospheric variables along with the dependence of engine variables upon flight condition and inlet performance. An off-design engine performance model is used to identify interaction parameters in the model. Inclusion of subsystem interaction effects introduces coupling between flight and propulsion variables. To analyze interaction effects on control, consideration is first given to control requirements for separate flight and engine models. For the separate airframe model, feedback control provides substantial improvement in short period damping. For the integrated system, feedback control compensates for the coupling present in the model and provides good overall system stability. However, this feedback control law involves many non-zero gains. Analysis of suboptimal control strategies indicates that performance of the closed loop integrated system can be maintained with a feedback matrix in which the number of non-zero gains is small relative to the number of components in the feedback matrix.

Fennell, R. E.↗
NASA NTRS1982

Crashworthy airframe design concepts: Fabrication and testing

Crashworthy floor concepts applicable to general aviation aircraft metal airframe structures were investigated. Initially several energy absorbing lower fuselage structure concepts were evaluated. Full scale floor sections representative of a twin engine, general aviation airplane lower fuselage structure were designed and fabricated. The floors featured an upper high strength platform with an energy absorbing, crushable structure underneath. Eighteen floors were fabricated that incorporated five different crushable subfloor concepts. The floors were then evaluated through static and dynamic testing. Computer programs NASTRAN and KRASH were used for the static and dynamic analysis of the floor section designs. Two twin engine airplane fuselages were modified to incorporate the most promising crashworthy floor sections for test evaluation.

Cronkhite, J. D.↗
NASA NTRS1982

Minimum mass sizing of a large low-aspect ratio airframe for flutter-free performance

A procedure for sizing an airframe for flutter-free performance is demonstrated on a large, flexible supersonic transport aircraft. The procedure is based on using a two-level reduced basis or modal technique for reducing the computational cost of performing the repetitive flutter analyses. The supersonic transport aircraft exhibits complex dynamic behavior, has a well-known flutter problem and requires a large finite-element model to predict the vibratory and flutter response. Flutter-free designs are produced with small mass increases relative to the wing structural weight and aircraft payload. In view of the ability of the resizing procedure to handle this supersonic transport configuration, it seems likely that the method could be used for many other aircraft.

Greene, W. H.↗
NASA NTRS1982

Gain selection method and model for coupled propulsion and airframe systems

A longitudinal model is formulated for an advanced fighter from three subsystem models: the inlet, the engine, and the airframe. Notable interaction is found in the coupled system. A procedure, based on eigenvalue sensitivities, is presented which indicates the importance of the feedback gains to the optimal solution. This allows ineffectual gains to be eliminated; thus, hardware and expense may be saved in the realization of the physical controller.

Murphy, P. C.↗
NASA NTRS1984

Airframe technology for aircraft energy efficiency

The economic factors that resulted in the implementation of the aircraft energy efficiency program (ACEE) are reviewed and airframe technology elements including content, progress, applications, and future direction are discussed. The program includes the development of laminar flow systems, advanced aerodynamics, active controls, and composite structures.

James, R. L., Jr.↗
NASA NTRS1986

Flexible Airframe Response Program

Generalized set of flexible vehicle equations-of-motion (EOM's) developed and incorporated into Flexible Airframe Response (FAR) program. Output from FAR program used in aircraft flight control system design.

Lin, C.↗
NASA NTRS1982

Fuel efficiency through new airframe technology

In its Aircraft Energy Efficiency Program, NASA has expended approximately 200 million dollars toward development and application of advanced airframe technologies to United States's commercial transports. United States manufacturers have already been given a significant boost toward early application of advanced composite materials to control surface and empennage structures and toward selected applications of active controls and advanced aerodynamic concepts. In addition, significant progress in definition and development of innovative, but realistic systems for laminar flow control over the wings of future transports has already been made.

Leonard, R. W.↗
NASA NTRS1985

Manufacturing tolerances for natural laminar flow airframe surfaces

Published aircraft surface waviness and boundary layer transition measurements imply that currently achievable low levels of surface waviness are compatible with the natural laminar flow (NLF) requirements of business and commuter aircraft, in the cases of both metallic and composite material airframes. The primary challenge to the manufacture of NLF-compatible surfaces is two-dimensional roughness in the form of steps and gaps at structural joints. Attention is presently given to recent NASA investigations of manufacturing tolerance requirements for NLF surfaces, including flight experiment results.

Holmes, B. J.↗
NASA NTRS1986

Optimal airframe synthesis for gust loads

An optimization capability for sizing airframe structures that are subjected to a combination of deterministic and random flight loads was established. The random vibration environment introduces the need for selecting a statistical process that best describes the random loads and permits computation of the dynamic response parameters of interest. Furthermore, it requires a formulation of design constraints that would minimize the conservativeness in the design and retain computational viability. The random loads are treated as a stationary, homogeneous process with a Gaussian probability distribution. The formulation of the analysis problem, the structure of the optimization programming system and a representative numerical example are discussed.

Hajela, P.↗
NASA NTRS1986

Automated tuning of airframe vibration by structural optimization

Numerical optimization techniques are used to modify the dynamic response at a specified point(s) of a helicopter airframe structure due to a steady state narrow band excitation. Calculation of steady state vibration amplitude is reduced to the solution of linear equations with complex coefficients. The sensitivity of the dynamic amplitudes with respect to the structural parameter perturbations can be computed with the same technique as the one used in the static displacement sensitivity without requiring eigenvector sensitivity. Approximate models for critical structural responses are created based on the sensitivity data to reduce the amount of computational effort and to enable the design of structures of practical scale and complexity. This approach is general in that it accommodates static, dynamic, and frequency constraints simultaneously as long as their computational models are available. It can be used in optimizing mass distribution as well as stiffness modifications of practical structures.

Miura, H.↗
NASA NTRS1989

Ground Shake Test of the Boeing Model 360 Helicopter Airframe

Boeing Helicopters, together with other U.S. Helicopter manufacturers, is engaged in a finite element applications program designed to emplace in the U.S. a superior capability to utilize finite element analysis models in support of helicopter airframe structurel design. This program was given the acronym DAMVIBS (Design Analysis Methods for VIBrationS). The test plan is reviewed and results are presented for a shake test of the Boeing Model 360 helicopter. Results of the test will serve as the basis for validation of a finite element vibration model of the helicopter.

Reed, D. A.↗
NASA NTRS1990

Fatigue crack initiation and small crack growth in several airframe alloys

The growth of naturally-initiated small cracks under a variety of constant amplitude and variable amplitude load sequences is examined for several airframe materials: the conventional aluminum alloys, 2024-T3 and 7075-T6, the aluminum-lithium alloy, 2090-T8E41, and 4340 steel. Loading conditions investigated include constant amplitude loading at R = 0.5, 0, -1 and -2 and the variable amplitude sequences FALSTAFF, Mini-TWIST and FELIX/28. Crack growth was measured at the root of semicircular edge notches using acetate replicas. Crack growth rates are compared on a stress intensity factor basis, to those for large cracks to evaluate the extent of the small crack effect in each alloy. In addition, the various alloys are compared on a crack initiation and crack growth morphology basis.

Swain, M. H.↗