Search NASA⌕ Search

SEARCH · Search NASA

Results for “BENDING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Understanding and Advancing Bifacial Thin Film Solar Cells under Dual Illumination

There is a great deal of interest in increasing the energy yield from thin film solar cells by implementing bifacial operation. However, deleterious band bending and high interface recombination at the back transparent electrode can cause problems. Herein, it is investigated how bifacial thin film devices perform when illuminated through the front, back, and simultaneously through both interfaces using numerical modeling. It is shown that the downward band bending near the back interface is reduced during illumination when the carrier concentration is low. This effect is not found when the doping is relatively high, but the minority carrier distribution is still modified. Under either condition, the power generated under bifacial illumination exceeds the sum of the power generated when the illumination is solely from the back or the front. It is also shown that the back-illuminated device performance is independent of the angle at which the light enters the back of the device, which provides accommodation for scattered light. Finally, the power enhancement is calculated for bifacial devices relative to front-illuminated devices, and is shown that any significant loss in frontside power generation is difficult to overcome with back illumination under real-world albedo conditions.

CdTe↗
DOE OSTI2023

Room Temperature Stamping of High-Strength Aluminum for Lightweight Structural Automotive Components

The use of aluminum (Al) 7xxx series in automobile structural applications is limited by factors such as its low room-temperature formability in T6 temper and the need for off-line artificial aging to regain high strength if it is formed in soft temper. In this study, two tempers were established that enable Al 7075 blanks to be room temperature stamped to create side impact beams that achieve near-T6 strength without post-forming artificial aging. It is shown that natural aging at room temperature, after solution treatment and before stamping, provides an alternative to high temperature pre-aging and hot stamping techniques in 7xxx alloys. Both tempers enabled room temperature stamping of the beams without cracking, indicating good formability. The Al beams were ~38% lighter than the benchmark boron steel beam. Further, the hardness in the low-deformation regions of the stamped Al beams were within 88% of a conventional 7075-T6 sheet. Paint-bake treatment of the beams appeared to cause over aging, lowering the ultimate tensile strength and ductility. Finite element three point bending simulations of the beams showed higher bending force and energy absorption before failure for the Al 7075 showing good promise for 7xxx series Al as a light-weight alternative to steel beams.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Facile healing of cracks in organic–inorganic halide perovskite thin films

Organic-inorganic halide perovskite (OIHP) thin films at the heart of the burgeoning thin-film perovskite solar cells (PSCs) technology possess poor mechanical properties, which is likely to limit the long-term reliability of PSCs as they are poised for commercialization. In an effort to address this issue, in this work we demonstrate that through-thickness cracks induced by bending-tension in thin films of the two prototypical OlHPs, methylammonium lead triiodide (MAPbl(3)) and formamidinium lead triiodide (FAPbl(3)), can be healed easily. This is through the application of either a moderate compressive stress (bending-compression) at room temperature or a simple heat-treatment at modest temperatures. The crack-healing process is found to be time-dependent, which indicates that facile mass-transport in OlHPs plays a key role in this phenomenon. An explanation for this phenomenon is provided, one based on the fundamentals of brittle fracture. This discovery has broad implications for the prevention and/or restoration of the overall performance, environmental stability, and mechanical reliability of PSCs, and other devices.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Domain patterns and super-elasticity of freestanding BiFeO 3 membranes via phase-field simulations

Super-elasticity of functional ferroelectric oxides offers promises for integrating ferroelectric films into flexible electronics. However, super-elastic deformation is a complex phenomenon related to possibly multiple concurrent mechanisms. Fundamentally understanding how multiple mechanisms contribute to the super-elasticity of ferroelectric oxides is crucial to realizing their potential flexible electronic applications. In this study, we employ phase-field simulations to model the dynamics of ferroelectric domain patterns of freestanding BiFeO 3 membranes to understand the origin of their super-elasticity under substantial bending deformation (5% strain). It is demonstrated that both a reversible Rhombohedral-Tetragonal (R-T) phase transition and a nearly reversible domain evolution of BiFeO 3 membranes contribute to accommodating the large deformation and thus their super-elasticity. The dynamics of domain evolution also reveal the formation of an exotic ferroelectric vortex and polarization rotation before the phase transition. We constructed a diagram of phases and domain patterns as a function of the membrane thickness and bending angle, which allows one to readily predict the emergence of T phase and ferroelectric vortex in bent BFO membranes. These results not only provide fundamental understanding of mesoscale super-elastic mechanisms but also reveal exotic domain states of ferroelectric membranes.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Atomistic modeling of energy band alignment in CdTe(1 0 0) and CdTe(1 1 1) surfaces

An atomic-scale perspective of energy band alignment in CdTe surfaces has not been spatially studied despite the major role surfaces play in forming interfaces within CdTe-based thin film photovoltaic devices. Atomistic modeling based on density functional theory coupled with surface Green’s function is used for calculating energy band alignment of CdTe surfaces. The CdTe(1 0 0) ((1×1) and c(2×2) reconstruction) and CdTe(1 1 1) ((1×1) and (2×2) reconstruction) facets without and with surface relaxation provide insightful band bending characteristics that influence charge carrier transport. Results show that unrelaxed (1×1) CdTe(1 0 0) and CdTe(1 1 1) surfaces bend the valence band downward with surface polarity dictating the surface potential magnitude. The reconstructed CdTe(1 0 0) c(2×2) and CdTe(1 1 1) (2×2) surfaces result in favorable surface electronic features in relation to their unreconstructed variants. In addition, the structurally relaxed CdTe(1 1 1) surfaces develop an internal energy cusp potential that may enhance hole charge transport toward the back of CdTe solar cell devices. In conclusion, energy band alignments calculated within the study lead to a detailed understanding of how CdTe surfaces may affect CdTe-based thin film photovoltaic applications.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Manufacturing and characterization of continuous fiber-reinforced thermoplastic tape overmolded long fiber thermoplastic

Light-weight construction, design freedom, integration of functions, and compelling cost element are desired by Original Equipment Manufacturers (OEMs) and their suppliers. The emergence of overmolding of continuous-discontinuous reinforcement enables design freedom and ability to tailor stiffness, strength, and damage tolerance for structural applications. In this work, long fiber thermoplastics (LFT) are overmolded with continuous fiber-reinforced thermoplastic (CFRTP) tape are combined using extrusion compression molding process to evaluate the structural performance. The CFRTP tape overmolded LFT samples were characterized using nondestructive and destructive techniques to track fiber alignment, fiber distribution, manufacturing defects, interfacial bonding of the tape – LFT and effect of CFRTP tape on LFT. Mode 1 fracture toughness, G 1c for tape overmolded LFT was higher by 25–30% compared to literature reported G 1c . This response was attributed to excellent fiber distribution, good fiber wetting, and absence of voids at the interface. Three-point bend test indicated that CFRTP tape overmolded LFT composites were better able to resist damage under the bending load compared to constituent LFT composite. Flexural strength of the overmolded composite was higher by 119–142%, and modulus higher by 77–65% compared to constituent LFT composite. Simulated flexural results accurately represents the mechanical behavior of composites. Here, the penetration energy of tape overmolded LFT composites determined by LVI test was in the range of 27.66–30.15 J, which is significantly higher than constituent LFT composite, 7.76 J. CFRTP tape overmolded LFT composite exhibits progressive fiber fracture, matrix cracking, and interfacial debonding failure, whereas, constituent LFT composite showed catastrophic fiber fracture.

42 ENGINEERING↗
DOE OSTI2022

Dynamic fracture of glass fiber-reinforced ductile polymer matrix composites and loading rate effect

Here, the dynamic fracture of S-2 glass fiber-reinforced polymer matrix composites (FRPMCs) was investigated in this study. The matrix ductility was improved by a recently developed network topology modification technique via mixing partially reacted substructures (mPRS). The composite material was manufactured and characterized by micro-CT scanning and scanning electron microscopy (SEM). Dynamic single-edge notched bending (d-SENB) experiments were performed on the composites by using a modified split-Hopkinson pressure bar. Each specimen’s fracture process was visualized by ultrafast X-ray imaging. Such in-situ radiography enabled identifying the damage initiation below 50-micron scale and inspecting its propagation through the internal structures of opaque composites, thereby accurately quantifying the composites’ mechanical properties. Furthermore, the identical d-SENB experiments were designed and the digital image correlation (DIC) was employed to monitor the stress wave propagation on the composite specimens. The force and deflection measurements were modified and correlated to the physical damage processes. Besides, quasi-static SENB experiments were conducted to identify the loading rate effects on the composites’ fracture behaviors. The force and deflection history, bending stiffness, energy dissipation, and fracture toughness at different loading rates were quantified and compared. Finally, post-fracture analysis by micro-CT scanning and SEM provided physical observations on the variation of the fracture morphology by different loading rates.

42 ENGINEERING↗
DOE OSTI2025

A new tubular ironless linear induction motor using non-interrupted winding method

The ironless linear induction motor device can be used for any application which requires a large motion span or rotation restrictedly by the ironless feature due to the strong magnetic field environment. One of the possible applications is ITER diagnostics shutters. The tokamak reactor systems have a severe radiation issue during the operation. The traditional Kapton-insulated wires have significantly lower radiation resistance than an expected large radiation dose at ITER Motion Stark Effect (MSE) shutter location. Furthermore, the traditional single-sided linear induction motor winds the wire to make the N-turn pitch coils independently and then connect them in series to make a one-phase winding. Therefore, it is a big challenge to make so many radiation-protection connectors in such a limited space as inside the vacuum vessel of fusion reactors. The approved mineral-insulated kinds of cables need a large bend radius for the end turns, so the traditional single-sided linear motor with two-layer three-phase windings need to be upgraded to the tubular linear motors. The new proposed tubular ironless linear induction motor can not only overcome the large bend radius issue with the mineral-insulated cables but also allow the motor coils wound continuously around the tubular-shaped stator, forward and backward N times to make a N-turn winding for each phase, in order to resolve the radiation protection issue with the winding connection. The 3D transient Maxwell electromagnetic model with a tubular three-phase linear induction motor has been analyzed. Furthermore, this paper will present the detailed design and winding method of ironless linear induction motor actuators, and results of the 3D transient numerical simulation of the actuator performance.

Ironless↗
DOE OSTI2021

High stability of flexible perovskite transparent conductive oxide film via van der Waals heteroepitaxy

Transparent conducting oxides (TCOs), such as indium-tin oxide (ITO) and indium gallium zinc oxide (IGZO), are essential components in the design of flexible optoelectronic devices. However, it is still a challenge to prepare low-cost flexible transparent conductive film for achieving the flexible functionality together with high optical transparency and electrical conductivity. Herein, fluorphlogopite (mica) is selected as the bendable and transparent substrate for the fabrication of low-cost perovskite CaVO 3 TCO epitaxial film. Benefitting from thin mica substrate with high Young’s modulus of 200 GPa, flexible CaVO 3 TCO epitaxial film exhibits high mechanical stability in terms of electrical conductivity and optical transparency after bending up to 10 5 cycles. The change of resistance can reflect the bending curvature and strain state. Finally, our results provide a new pathway to design superior mechanical flexibility and stability CaVO 3 TCO films for application in flexible, light-weight, and portable smart optoelectronic devices.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Leak-tight crack repair for 304L stainless steel using friction surfacing

Here, friction surfacing (FS) was investigated as a method for sealing 50 μm wide thru-cracks in 3-mm-thick 304L stainless steel (304L) plate. Friction surfacing was performed using two sizes of 304L consumable rod, with diameters of 9.52 mm and 12.7 mm, on two substrate conditions (clean and oxidized). Friction surfacing was able to deposit a 600 μm thick coating and repair cracks to a depth of 100 μm - 200 μm below the original surface, when using the 12.7-mm-diameter consumable rod for both substrate conditions. Helium leak rates of 10 -10 atm-cc/s were achieved on crack repairs, designating them as leak-tight by the ANSI N14.5 standard. Optical and scanning electron microscopy were used to investigate the coating microstructure and bond interfaces. In this study, the 12.7-mm-diameter rod performed better with disruption of the oxide layer on the oxidized substrate and providing a more homogenous coating. Mechanical properties of the coated samples were evaluated by performing micro-indentation, tensile, bending, and adhesion testing. Higher hardness in the coatings was observed due to the fine equiaxed grains resulting from dynamic recrystallization. Complete consolidation of plastically deformed material on the substrate and a strong diffusion bond across the interface was observed. This was reflected in tensile and bending properties of the FS coatings being comparable to those of uncoated specimen. No delamination of the FS coating was observed during adhesion testing. The results demonstrate that friction surfacing is a viable option to seal cracks in stainless steels.

36 MATERIALS SCIENCE↗
DOE OSTI2020

The 1.66 μm spectrum of the ethynyl radical, CCH

Frequency-modulated diode laser transient absorption spectra of the ethynyl radical have been recorded at wavelengths close to 1.66 μm. The observed spectrum includes strong, regular, line patterns. The two main bands observed originate in the ground $\tilde{χ}$ 2 Σ + state and its first excited bending vibrational level of 2 $Π$ symmetry. The upper states, of 2 Σ + symmetry at 6055.6 cm -1 and 2 $Π$ symmetry at 6413.5 cm -1 , respectively, had not previously been observed and the data were analyzed in terms of an effective Hamiltonian representing their rotational and fine structure levels to derive parameters which can be used to calculate rotational levels up to J = 37/2 for the 2 $Π$ level and J = 29/2 for the 2 Σ one. Additionally, a weaker series of lines have been assigned to absorption from the second excited bending, (0 2 0), level of 2 Σ symmetry, to a previously observed state of 2 $Π$ symmetry near 6819 cm -1 . These strong absorption bands at convenient near-IR laser wavelengths will be useful for monitoring CCH radicals in chemical systems.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2023

The effects of radiation-induced grain subdivision and dislocations on the fracture properties of uranium dioxide

Microcantilever bending tests were applied on uranium dioxide samples irradiated by 84 MeV Xe ions. Depending on the initial grain sizes, different levels of grain subdivision and dislocation development were observed near the irradiated surface. These radiation damage features were shown to degrade the fracture properties of both samples. The fundamental aspects of the radiation-microstructure-property relationships were discussed in this paper, taking a holistic consideration of the microcantilever bending data, fractography and microstructures. The separate effects of the irradiation-induced grain subdivision and dislocations on the fracture initiation and propagation of uranium dioxide were discussed. In conclusion, it was observed that radiation-induced dislocations and grain subdivision, without the presence of Xe bubbles co-located with the defects, cause reductions in the Young's modulus, fracture strain, and fracture stress, and a transition to intergranular fracture.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Deformation and Delamination of Dynamically Bulging Bilayered Films

We employ finite element simulations to study the dynamic bulging of films under shock tube conditions and compare these responses with quasi-static bulging. Both scenarios subject the film to time-varying pressure. Two film types are considered: uniform material films and bilayers with a relatively soft interior layer and a hard exterior layer. The interface between the materials in the bilayer cases is modeled as a cohesive zone that follows a bilinear normal traction-separation cohesive law. Additionally, bilayer films with preexisting cracks in the interior layer are analyzed. Parametric studies are also conducted to explore the effects of loading rate and specimen size. The mechanical response of all materials is assumed to be strain-rate independent, focusing solely on the inertial effects in the response of the films under dynamic loading, and the absence of such effects under quasi-static loading. The results indicate that quasi-static bulging exhibits a predictable plate bending like deformation. In contrast, depending on the loading rate and specimen size, dynamic bulging can give rise to elastic waves, and a sequence of deformation processes including initial uniform acceleration, followed by bending-like deformation, and finally through-thickness biaxial stretching. Dynamic loading also leads to larger bulge formation and greater deformation than quasi-static loading. A key finding is the role of preexisting cracks in driving delamination under dynamic loading, which is absent in quasi-static loading. This work enhances our understanding of dynamic bulging and motivates further research on characterizing delamination in layered films using dynamic bulge tests.

36 MATERIALS SCIENCE↗
DOE OSTI2022

An implantable biomechanical energy harvester for animal monitoring devices

Insufficient service life and the resulting need for battery replacements have been a great challenge for implantable electronic devices. This is particularly true for animal tracking applications, because recapturing animals is often unlikely once they are released to the wild. To tackle this problem, we developed a biomechanical energy harvester that uses a Macro Fiber Composite™ (MFC) piezoelectric beam to harvest the mechanical energy from animals’ body bending movements as the power source for implantable and wearable devices. Prototypes of an underwater acoustic transmitter using this technology were subdermally implanted into juvenile white sturgeon and their energy harvesting performance was evaluated through the device’s transmissions. Additionally, the fish successfully recovered from the implantation surgery and freely swam inside a tank. The transmitter prototypes in the fish continually transmitted signals for a period up to 5 weeks. A benchtop test setup was also created to emulate the fish’s body bending, estimate the device’s energy harvesting performance in the live fish, and perform accelerated fatigue testing of the energy harvester by applying test parameters learned from a video study of the fish’s body movement and behavior characteristics. The gradual depolarization of the piezoelectric ceramic material in the MFC under cyclic mechanical loading was the main limiting factor for the life span of the energy harvester. Pathways for improvement are proposed to achieve long-term efficacy of powering implantable and wearable electronic devices.

42 ENGINEERING↗
DOE OSTI2024

Large radial shift experiments in RHIC and their implications for EIC design

The Hadron Storage Ring (HSR) in the future Electron-Ion Collider (EIC) must operate over a broad range of design circumferences. In 2018 preliminary beam studies on the circumference adjustment capabilities of the Relativistic Heavy Ion Collider (RHIC) were performed by applying a small momentum offset to the circulating bunches without adjusting any bending magnets. The off-momentum linear optics were corrected back to on-momentum conditions. Applying a similarly small deviation to the dipole fields of a select set of bending magnets provides a large radial shift over much of the RHIC (or HSR) circumference while leaving the design trajectory unchanged in the insertion regions. Here, this paper presents the design of the different lattice configurations foreseen as the most viable options for the required HSR circumference changes, and highlights the modifications necessary for regular operations and to allow for testing these new settings in RHIC. Experimental results from 2021 and 2022 are reviewed and compared to model predictions obtained from both MAD-X and Bmad. The implications of these results for HSR design are discussed.

43 PARTICLE ACCELERATORS↗
DOE OSTI2023

Influence of fatigue precracking and specimen size on Master Curve fracture toughness measurements of EUROFER97 and F82H steels

EUROFER97 and F82H steels are two leading reduced-activation ferritic-martensitic (RAFM) steels for fusion first wall and blanket applications. Exposure to the harsh environment of fusion reactors can result in severe degradation of fracture toughness. Thus, the post-irradiation evaluation of fracture toughness is critical for understanding the material behavior. Due to the space constraints of irradiation facilities and challenges in controlling a uniform irradiation condition for large size specimens, the development of small specimen test techniques (SSTT) is indispensable to evaluate the performance of irradiated materials. In this study, we evaluated specimen size effects on the Master Curve fracture toughness of EUROFER97 and F82H steels. A wide variety of specimens, including 0.5 T compact tension (C(T)) specimens, 0.16 T mini-compact tension (miniC(T)) specimens, and 1.65 mm miniature bend bar specimens, were tested. The testing methodology was based on the Master Curve method in the ASTM E1921 standard. No specimen size effect was observed in 0.5 T C(T) and 0.16 T miniC(T) specimens on the Master Curve reference temperature T0, while 1.65 mm miniature bend bar specimens yielded a higher T 0Q . A strong effect of fatigue precracking on T 0 for 0.5 T C(T) and 0.16 T miniC(T) specimens was observed, such that testing on specimens with skewed fatigue precrack fronts resulted in lower T 0 than for specimens with ASTM standard qualified straight fatigue precrack fronts. The results highlight the importance of experimental quality control in developing SSTT for Master Curve fracture toughness testing. Lastly, we also evaluated and provided recommendations on the minimum number of specimens needed for each specimen type for yielding reliable T 0Q values.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Impact of control blade insertion on the deformation behavior of SiC-SiC channel boxes in BWRs

This article describes the analysis of distortion of a silicon carbide fiber-reinforced, silicon carbide matrix (SiC-SiC) composite channel box under in-reactor conditions of a boiling water reactor (BWR). The BWR core has significant gradients in the fast neutron flux across the channel box due to the presence of water rods within the fuel assemblies, and these gradients increase further with the insertion of control blades. As a result of the temperature and neutron flux dependent irradiation-induced swelling of SiC, the SiC-SiC composite channel box can undergo distortion. In this work, we evaluate the SiC-SiC channel box distortion for three different control blade positions. This analysis is based on the neutron flux and temperature distributions in the BWR core calculated using the neutronics code MPACT and thermal-hydraulics code CTF. This calculation is coupled through temperature feedback. Subsequently, we have performed structural analysis based on the calculated neutron flux and temperature distributions to determine the deformation and stress development in the channel box. The structural analysis was performed using the fuel performance modeling code BISON and the commercial finite element analysis software Abaqus. The results indicate that large gradients in fast neutron flux (up to 35–40% across a single axial level) will develop across the channel box. Due to these gradients, the channel box will undergo time-dependent bending for all the control blade positions in the assembly. The time-dependent bowing behavior is dominated by the transient swelling of SiC-SiC material under non-uniform neutron flux, and changes with variation in the control blade position. The bending will cause temporary interference between the channel box and control blade, and the interference is expected to be most severe for the fully inserted control blade position. The developed stresses due to differential swelling in the channel box exceed the proportional limit stress of the material, which may cause matrix microcracking in the channel box. However, the stresses remain below the tensile strength of the material, and therefore, development of a full, through-thickness crack in the channel box is not expected. Finally, further work is recommended to explore and evaluate the mitigation strategies.

42 ENGINEERING↗
DOE OSTI2021

Additive manufacturing of cobalt-based alloy on tool steel by directed energy deposition

Cladding hard-surfacing alloys on tool steel is an effective approach to enhance the surface properties of tool steel. In this study, a Co-based alloy was deposited on tool steel by Directed Energy Deposition (DED) following a three-factor three-level design of experiment matrix with varied laser power, scan speed, and powder flow rate. The microstructure of the deposits was characterized using scanning electron microscopy (SEM). The residual stress on the surface of the samples was measured by the X-ray diffraction (XRD) sin2? technique. The parameters that produced promising deposits were used to fabricate samples for tensile test, four-point bending test, Charpy impact test, and hardness measurement. Our result reveals that the processing parameters have a significant role in the residual stress of the coatings. Residual stress reduces with the increase of laser energy density. Cracks were found at samples with energy density below a threshold. Tensile testing of the coating/substrate combined structure reveals fracture at the coatings with an ultimate tensile strength of 633.9 ± 54.7 MPa. The bi-material interface survived the tensile test, indicating a strong interfacial bond. The four-point bending test of coating/substrate laminates shows an ultimate flexure strength of 860.6 ± 36.9 MPa. Cracks initiated from the coatings ignored the interface and penetrated the substrate, suggesting a solid bi-material bond. Charpy impact test shows the absorbed energy of coating/substrate laminates is more than doubled that of the substrate.

36 MATERIALS SCIENCE↗