SEARCH · Search NASA

Results for “BOUNDARY VALUE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

All sources NASA NTRS DOE OSTI

DOE OSTI2024

CICE on a C-grid: new momentum, stress, and transport schemes for CICEv6.5

Abstract. This article presents the C-grid implementation of the CICE sea ice model, including the C-grid discretization of the momentum equation, the boundary conditions (BCs), and the modifications to the code required to use the incremental remapping transport scheme. To validate the new C-grid implementation, many numerical experiments were conducted and compared to the B-grid solutions. In idealized experiments, the standard advection method (incremental remapping with C-grid velocities interpolated to the cell corners) leads to a checkerboard pattern. A modal analysis demonstrates that this computational noise originates from the spatial averaging of C-grid velocities at corners. The checkerboard pattern can be eliminated by adjusting the departure regions to match the divergence obtained from the solution of the momentum equation. We refer to this novel approach as the edge flux adjustment (EFA) method. The C-grid discretization with edge flux adjustment allows for transport in channels that are one grid cell wide – a capability that is not possible with the B-grid discretization nor with the C-grid and standard remapping advection. Simulation results match the predicted values of a novel analytical solution for one-grid-cell-wide channels.

Lemieux, Jean-François (ORCID:0000000320845759)↗

DOE OSTI2026

IM3 Projected US Data Center Locations

IM3 Projected US Data Center Locations This dataset contains model projections of new data center facilities in the contiguous United States (CONUS) through 2035 using the CERF – Data Centers model. Data center locations are modeled across four data center electricity demand growth scenarios (low, moderate, high, higher) and five market gravity scenarios (0%, 25%, 50%, 75%, 100%). Projected locations are intended to be regional representations of feasible siting locations in the future to assess potential grid and water stress impacts. The data center load growth scenarios correspond with the rates outlined in EPRI (2024) and include 3.71%, 5%, 10%, and 15% annual growth of electricity demand for data centers from 2023 values in 37 states across the CONUS. Market gravity scenarios correspond to the relative importance of proximity to data center markets or high population areas compared to locational cost in the siting algorithm. 0% market gravity means that siting decisions were entirely determined by the locational cost in each feasible location. 100% market gravity means that only market proximity was considered when siting. Other scenarios have weight placed on both components where total weight always equals 100%. Locational cost is dependent on facility cooling type and corresponding electricity cost, taxes, and other factors. Facility cooling type is spatially determined where high water stress and/or areas with high summer wet bulb temperatures are assumed to operate with mechanical cooling for a higher fraction of the year rather than evaporative cooling. Feasible data center siting areas are based on geospatial suitability raster data developed with open-source information. The following areas are excluded from siting: Areas within 300 m of a federal airport runway or within an airport area boundary Waterbodies Areas with slope >16% Areas susceptible to sinkholes High coastal or inland flood risk areas Local, state, and federal parks, leisure areas, and cemeteries Areas >2 km away from electric substations Areas >5 km away from a municipal water supplier service area Areas >2 km away from high-speed fiber provider service territory USGS Protected Areas Database of the United States (PAD-US) GAP status 1, 2, or 3 areas US National Parks Wetlands USFWS critical habitats BIA land areas Railroads, major roadways, and minor roadways Military areas and training grounds NLCD developed lands Areas >0.8 km (0.5 miles) from NLCD developed lands Because we use open-source information, proprietary information that can influence siting decisions such as individual tax agreements with cities, detailed fiber line connectivity, electric grid power capacity agreements, and others, are not currently accounted for in the modeling process. Using specific building locations and footprints in the dataset for local planning purposes is not advised. Technical Information Geospatial data is provided in geojson format using the Albers Equal Area Conic (ESRI:102003) coordinate reference system. The datasets contain the following parameters: id - unique identification number within given scenario file growth_scenario – data center demand growth scenario market_gravity_weight – market gravity weight scenario (%) region – name of region (i.e., US State) total_cost_million_usd – locational siting cost ($million) campus_size_square_ft – total land acquired for data center facility (square ft) data_center_it_power_mw – IT power of data center facility (MW) mechanical_cooling_frac – fraction of year when data center uses mechanical cooling system water_cooling_frac– fraction of year when data center uses evaporative cooling system cooling_energy_demand_mwh – total annual facility energy demand for cooling (MWh) cooling_water_demand_mgy – total annual facility water demand for cooling (MG) cooling_water_consumption_mgy – total annual facility water consumed (MG) normalized_locational_cost – normalized total locational cost score for location normalized_gravity_score – normalized market gravity score for location weighted_siting_score – total weighted siting score of locational cost and gravity score geometry – polygon geometry of facility Acknowledgment IM3 is a multi-institutional effort led by Pacific Northwest National Laboratory and supported by the U.S. Department of Energy's Office of Science as part of research in MultiSector Dynamics, Earth and Environmental Systems Modeling Program. License This data is made available under a CCBY4.0 License Disclaimer This material was prepared as an account of work sponsored by an agency of the United States Government. Neither the United States Government nor the United States Department of Energy, nor the Contractor, nor any or their employees, nor any jurisdiction or organization that has cooperated in the development of these materials, makes any warranty, express or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or usefulness or any information, apparatus, product, software, or process disclosed, or represents that its use would not infringe privately owned rights. Reference herein to any specific commercial product, process, or service by trade name, trademark, manufacturer, or otherwise does not necessarily constitute or imply its endorsement, recommendation, or favoring by the United States Government or any agency thereof, or Battelle Memorial Institute. The views and opinions of authors expressed herein do not necessarily state or reflect those of the United States Government or any agency thereof. PACIFIC NORTHWEST NATIONAL LABORATORYoperated byBATTELLEfor theUNITED STATES DEPARTMENT OF ENERGYunder Contract DE-AC05-76RL01830

Mongird, Kendall (ORCID:0000000328077088)↗

DOE OSTI2025

Mode transitions and spoke structures in E × B Penning discharge

Two-dimensional particle-in-cell simulations in the (radial-azimuthal) plane perpendicular to the axial direction of a cylindrical $E$ x $B$ Penning discharge are presented. The low-pressure discharge is self-consistently supported by plasma ionization from the electron beam injected axially, along the direction of the external magnetic field. It is shown that with the increasing strength of the external magnetic field, the discharge undergoes a sequence of transitions between several azimuthal modes. Azimuthal m > 1 spiral arm structures are excited at low magnetic field values as plasma confinement improves and the radial density profile becomes peaked. With a larger field, spiral arms with m > 1 are replaced by the m = 1 spoke mode, most clearly seen in plasma density. A transition from spiral arms to the spoke regime occurs when the plasma potential in the center changes from weakly positive (or zero) to negative. Further increase in the magnetic field results in a well-developed m = 1 spoke mode with additional small-scale higher-frequency m > 1 structures inside and around the spoke. It is shown that while ionization and collisions affect some characteristics of the observed fluctuations, the basic features of the spoke and m > 1 spiral structure remained similar without ionization. The role of energy conservation in small-scale high-frequency modes and spoke dynamics is discussed. It is demonstrated that in regimes with the m = 1 spoke mode, additional m = 4 harmonics of the ion and electron fluxes to the wall appear due to the square boundary. The frequency of the m = 1 mode is weakly affected by the geometry of the boundary.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2024

Accurate machine-learning predictions of coercivity in high-performance permanent magnets

Increased demand for high-performance permanent magnets in the electric vehicle and wind-turbine industries has prompted the search for cost-effective alternatives. Discovering magnetic materials with the desired intrinsic and extrinsic permanent magnet properties presents a significant challenge to researchers because of issues with the global supply of rare-earth elements, material stability, and a low maximum magnetic energy product BH max . While first-principles density functional theory (DFT) predicts materials’ magnetic moments, magnetocrystalline anisotropy constants, and exchange interactions, it cannot compute extrinsic properties such as coercivity (H c ). Although it is possible to calculate H c theoretically with micromagnetic simulations, the predicted value is larger than the experiment by almost an order of magnitude due to the Brown paradox. To circumvent these issues, we employ machine-learning (ML) methods on an extensive database obtained from experiments, DFT calculations, and micromagnetic modeling. The use of a large experimental dataset enables realistic H c predictions for materials such as Ce-doped Nd 2 ⁢Fe 14 ⁢B, comparing favorably against micromagnetically simulated coercivities. Remarkably, our ML model accurately identifies uniaxial magneto-crystalline anisotropy as the primary contributor to H c . With DFT calculations, we predict the Nd-site-dependent magnetic anisotropy behavior in Nd 2 ⁢Fe 14 ⁢B, confirming that Nd 4⁢g sites mainly contribute to uniaxial magnetocrystalline anisotropy, and also calculate the Curie temperature (T c ). Finally, both calculated results are in good agreement with the experiments. The coupled experimental dataset and ML modeling with DFT input predict H c with far greater accuracy and speed than was previously possible using micromagnetic modeling. Further, we reverse engineer the grain-boundary and intergrain exchange coupling with micromagnetic simulations by employing the ML predictions.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

DOE OSTI2024

Baselining the Indirect Effect by Improving Quantification of Sea Spray and Marine Sources at Ascension Island (Final Report)

Oceans cover two-thirds of the Earth and understanding the interactions of aerosols with clouds in these large marine regions requires quantifying the man-made contributions to the budget of cloud-drop forming particles (known as cloud condensation nuclei, or CCN) relative to the non-manmade “baseline” conditions and understanding the meteorology of boundary layer clouds. Modeling studies have shown substantial uncertainties and sensitivities to natural marine CCN sources, meaning that to reduce uncertainties in indirect effects we must be able to better quantify the CCN budget in ocean regions. While models provide important constraints on these uncertainties, actually reducing uncertainties requires substantial observations in open-ocean and coastal regions in order to establish the baseline on which manmade emissions are added. The tropical South Atlantic Ocean is one of the least-sampled regions of the planet, making the comprehensive measurements of the Department of Energy Atmospheric Radiation Measurement Layered Atlantic Smoke Interactions with Clouds (LASIC) campaign provides the longest record of aerosol size distribution measurements from a differential mobility analyzer in a cloud-influenced marine location in the ARM database, with 17 months of ground-based aerosol size distribution measurements. This project addressed the research topic of Aerosol-Cloud Interactions (ACI) by supporting three publications from the LASIC measurements: 1. The ARM measurements were combined with a new value-added technique that was pioneered by the Russell group for quantifying sea salt. This quantification of sea salt uses supermicron scattering measurements for retrieving reasonable sea spray mass concentrations, providing the best-available, observationally-constrained estimate of the sea spray mode properties when supermicron size distribution measurements are not available. 2. The fitted modes of the distribution were used to investigate the signatures of cloud processing for very clean to very smoky aerosol conditions, revealing not only differences in the particles that activate in clouds but also in the mechanisms that control that droplet formation process. In clean air, the size required to form a cloud droplet is influenced by the number of particles, as well as how quickly particles take up water during growth in cloud. 3. Building on this aerosol characterization, cloud and meteorological conditions were used to evaluate aerosol-related changes in cloud albedo and optical depth. We introduced a new method of decomposing the impact of aerosols on clouds known as the Twomey effect by incorporating retrieved supersaturation from two independent sets of observations to constrain the feedback of aerosol particles on cloud properties. The method quantifies the reduction of the Twomey effect at high aerosol concentrations, which has never been explained quantitatively by observations. In addition, the results provide the first direct validation for the conditions observed in the tropical South Atlantic of a parcel-based approach that is embedded in many climate models. Together these findings illustrate how ARM extended field campaigns in stratocumulus-covered regions can be used to constrain ACI processes with direct observations, providing specific radiative effects without models. By making such process-specific constraints available to improve ACI in global climate models, ARM observations play a key role in supporting model development.

58 GEOSCIENCES↗

DOE OSTI2024

A Study of Slow-mode Shocks in the Near-Earth Magnetotail with MMS Observations and Hybrid Simulations

The structure of the magnetic reconnection boundary, particularly the presence of slow-mode shocks in the near-Earth magnetotail was studied by using magnetospheric multiscale (MMS) observations and 2.5D hybrid simulations. A total of 51 crossings of MMS from 2017 to 2021 were analyzed. We found that the detection percentage of slow-mode shocks in the near-Earth magnetotail is 41%–55%. Previous studies have only reported one slow-mode shock event in the near-Earth magnetotail and a slow-mode shock detection percentage of 10% or lower in the mid-to-distant magnetotail. It was observed that if the high-energy beam region data is removed from the slow-mode shock downstream observations then the detection of slow-mode shocks reduces, implying that the kinetic effects play an important role in the detection of slow-mode shocks. For the crossings where the interface was not identified as a slow-mode shock, it was found that the turbulence in those crossings can change the mass flux values and disrupt the detection of slow-mode shock. However, the macroscopic slow-mode shock-like structure stably exists around the magnetic reconnection interface, as most of the conditions for slow-mode shocks were satisfied. This result suggests that slow-mode shocks are a general feature of magnetic reconnection geometry. We find that the lack of detection of slow-mode shocks in previous observations and simulations can be explained by taking into account the kinetic structure of slow-mode shocks and the presence of turbulence.

79 ASTRONOMY AND ASTROPHYSICS↗

DOE OSTI2026

Validation Studies of RELAP5-3D for High-Temperature Gas-Cooled Reactor Analysis Using a Refined RELAP5-3D Model of the High Temperature Test Facility

RELAP5-3D has been used extensively for high-temperature gas-cooled reactor (HTGR) analysis, but such analysis lies outside the validation basis for the code. Oregon State University (OSU) and the United States Department of Energy’s (DOE) Advanced Reactor Technologies (ART) – Gas-cooled reactor campaign worked together to design and operate the High Temperature Test Facility (HTTF) at OSU to provide validation data for prismatic HTGR thermal hydraulics analysis. Work using a previous RELAP5-3D model of HTTF demonstrated the ability to reproduce trends in HTTF data but an inability to reproduce the values measured in multiple experiments within the uncertainty. It was hypothesized that a new model with a finer radial nodalization would perform better for HTTF analysis. In this paper, we present the development of that more refined model and analyze HTTF experiments PG-27 and PG-29, a pressurized (PCC) and depressurized conduction cooldown (DCC) transient. Comparing PG-27 results to experimental data shows a better prediction of steady state and transient temperatures; however, a deeper dive reveals that better transient temperature predictions are a result of better initial conditions. The transient temperature rise in the core is comparable between the two models, but the legacy model predicts temperatures in the reflectors better. The new model demonstrates the ability to predict unique temperatures in each sector of the core during PG-29, capturing the azimuthal asymmetry; however, the temperature predictions still differ from measured temperatures. One hypothesis is that differences between the assumed and actual power distribution leads to the underprediction of the individual block temperatures. These results suggest that gaps and uncertainties in the measured boundary conditions for the HTTF tests do not allow to fully validate RELAP5-3D for prismatic HTGR analyses. The authors suspect that some of the differences between predicted and measured temperatures may be a result of uncertainties associated with HTTF itself rather than RELAP5-3D. We demonstrated improved validation for steady-state analysis, but significantly improved transient performance has yet to be recognized.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2024

Shearless effective barriers to chaotic transport induced by even twin islands in nontwist systems

For several decades now it has been known that systems with shearless invariant tori, nontwist Hamiltonian systems, possess barriers to chaotic transport. These barriers are resilient to breakage under perturbation and therefore regions where they occur are natural places to look for barriers to transport. Here we describe a kind of effective barrier that persists after the shearless torus is broken. Because phenomena are generic, for convenience we study the standard nontwist map (SNM), an area-preserving map that violates the twist condition locally in the phase space. The barrier occurs in nontwist systems when twin even period islands are present, which happens for a broad range of parameter values in the SNM. With a phase space composed of regular and irregular orbits, the movement of chaotic trajectories is hampered by the existence of shearless curves, total barriers, and a network of partial barriers formed by the stable and unstable manifolds of the hyperbolic points. Being a degenerate system, the SNM has twin islands and, consequently, twin hyperbolic points. We show that the structures formed by the manifolds intrinsically depend on period parity of the twin islands. For this even scenario the structure that we call a torus free barrier occurs because the manifolds of different hyperbolic points form an intricate chain atop a dipole configuration and the transport of chaotic trajectories through the chain becomes a rare event. This structure impacts the emergence of transport, the escape basin for chaotic trajectories, the transport mechanism, and the chaotic saddle. The case of odd periodic orbits is different: we find for this case the emergence of transport immediately after the breakup of the last invariant curve, and this leads to a scenario of higher transport, with intricate escape basin boundary and a chaotic saddle with nonuniformly distributed points.

classical mechanics↗

DOE OSTI2024

DECOVALEX-2023: Task C Final Report

The Full-scale Emplacement (FE) heater experiment at the Mont Terri Underground Rock Laboratory (URL) was designed and conducted by Nagra to replicate an emplacement tunnel of Nagra’s reference repository design at 1:1 scale. Alongside testing the technical feasibility of constructing disposal tunnels, emplacing waste containers in the tunnels and then backfilling them, the main goals of the FE experiment are (1) to obtain a better understanding of the coupled effects of induced thermo-hydro-mechanical (THM) processes that may occur and (2) to validate existing coupled THM models (Müller et al., 2017). A key aspect of ensuring safety for repositories located in low-permeability rock involves minimizing any damage to the rock itself, thereby preserving its integrity and promoting a stable environment Amongst a number of processes that could damage the rock is the increase in pore pressure due to thermal loading caused by heat emitted from the waste. To reduce the potential damage of the rock, it is important to analyse the evolution of heat over time due to the heat load of the containers and assess possible consequences by coupled THM models. The aim of Task C of DECOVALEX-2023 was to build 3D numerical models of the FE experiment, focussing in particular on the heating induced pore pressure change in the Opalinus Clay. Data from a large number of sensors were available from the FE experiment for model comparison. These sensors measured temperature and relative humidity in the bentonite around the heaters, and temperature, pressure and displacement/strain in the surrounding Opalinus clay. Data were available from the start of excavation (April 2012) up to August 2020 for most sensors (more than 5 years from the start of heating in December 2014). To fulfil the overall aim of the task, the work was broken down into a number of steps, starting with simpler models to build confidence in each team’s approach and then moving to more complex models that better represent the FE experiment. Step 0 consisted of 2D benchmark models, gradually increasing the number of processes that are represented from thermal (T) only models in Step 0a, to coupled thermal hydraulic (TH) models in Step 0b with a representation of changing porosity, to coupled thermo-hydro-mechanical (THM) models in Step 0c, where porosity changes are calculated by the mechanical model. A detailed specification of processes, parameters, initial and boundary conditions was provided for this step, with the ambition that all teams would work towards close agreement in their model results, thus building confidence in the model implementations. vi It was not straightforward to achieve agreement between the teams, so additional steps (Step 0b2, 0b3, 0c2, 0c3) were added along with derivation of some analytical solutions against which the models could be compared. The reasons for the differences between teams were investigated and found to be caused primarily by different conceptual model assumptions (including temperature dependence of the thermal expansion of water), different model formulations (including porosity evolution) and differences in modelled domain sizes, boundary conditions and grid discretisation. This demonstrates that comparisons between multiple modelling teams and/or comparison with analytical results and experimental data are highly beneficial in providing an indication of uncertainty in model predictions. At the conclusion of Step 0, almost all teams had achieved a close agreement in model results and those that had not achieved an agreement knew the reason for this. Step 1 moved from 2D models to 3D models of the FE experiment without adding technical features like shotcrete or EDZ, and only considering the heating phase. Initially the 3D model was tightly specified to continue to build confidence in the model implementations (Step 1a). The results of Step 1a were compared to the data from the FE-experiment without the teams seeing the data. The teams were then provided with a sub-set of the data from the FE-experiment and invited to consider how best to use the large dataset for model comparison (Step 1b). Teams were then asked to use the data provided to calibrate their models, only changing material property values rather than adding features or processes to their models (Step 1c). In Step 1, teams were asked to only model the heating phase of the experiment, so pressure in the Opalinus Clay was reported as change in pressure since the initial conditions were specified rather than modelled. The change from 2D to 3D models was accompanied by an increase in the dispersion of results between the teams. Some of this was resolved during the task, but some remained and is potentially due to model discretisation. Calibration of parameters was useful in improving the fit of the models to the data but the remaining differences indicated that the models were missing features or processes. In Step 2, the teams were asked to update their models with additional features and processes as well as calibrating parameters to try and improve the fit of the models to the data. Teams were encouraged to represent ventilation of the open FE tunnel prior to backfilling with heaters and bentonite and in Step 2, the absolute pressure in the Opalinus Clay was compared between the teams. Teams took different approaches, but there was consideration of adding shotcrete and an EDZ into the model, representing stress change during excavation and different approaches to modelling ventilation of the FE tunnel. Overall, the documented results showed a very good agreement for temperature. The results for porewater pressure evolution showed a significant improvement for most teams compared to Step 1c with a good agreement to the measurements for several teams whereas some teams overpredicted the pressure increase and others overpredicted the drainage effect especially for the sensors close to the heater. Step 3 was an opportunity for teams to use the models developed in Step 1 and Step 2 to make predictions about the temperature and pressure changes that will be expected at the FE experiment over the next few years in light of the planned changes in thermal output of the heaters.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2026

Performance of reanalysis and mesoscale models off the coast of Hawai'i

The eastern Hawai'i coast in the United States is characterized by considerable wind resource fuelled by persistent trade winds, making it an important area for energy research. The need is strong for reanalyses and higher-resolution regional simulations where observations have been historically limited, such as Hawai'i's offshore environments. However, studies using offshore observations in other parts of the world have shown that significant errors can occur in reanalyses and wind datasets, which can lead to inaccurate estimates of wind energy generation, payback periods, and extreme weather risks at project locations. The degree of such errors is influenced by a number of factors, including spatial resolution and the handling of processes within the planetary boundary layer (PBL). In this work, we provide a wind resource characterization from year-long lidar buoy measurements off the eastern coast of O'ahu, Hawai'i, an environment previously unobserved at the rotor level, and use the characterization to evaluate the performance of two simulation datasets. The O'ahu deployment location is meteorologically unique and less complex than land-based wind resource characterizations, being strongly characterized by trade winds with minimal land–atmosphere interaction influences. Despite the unique and fairly consistent meteorological conditions, we hypothesize that distinct simulation datasets will exhibit diverse ranges of errors similar to those that have been seen for other offshore locations. We find the European Centre for Medium-Range Weather Forecasts (ECMWF) Reanalysis version 5 (ERA5) to strongly underestimate observed wind speeds at the O'ahu location (bias = −1.54 m s −1 at a height of 140 m above sea level), while a regional Weather Research and Forecasting Model (WRF) simulation produced by the University of Hawai'i (UH-WRF) provides a significantly smaller wind speed bias (−0.25 m s −1 ), highlighting the value of running regional, higher-resolution simulations. The large bias noted for ERA5 is driven by significant underestimation of fast wind speeds (>9 m s −1 ), which the study site is largely characterized by, along with discontinuities in the ERA5 diurnal cycle. We also speculate that the relative sparsity of observations for data assimilation in this remote part of the world could influence the performance of ERA5 and that challenges with characterizing island effects could impact the performance of both datasets.

17 WIND ENERGY↗

DOE OSTI2025

Evaluating spectral cloud effective radius retrievals from the Enhanced MODIS Airborne Simulator (eMAS) during ORACLES

Satellite remote sensing retrievals of cloud effective radius (CER) are widely used for studies of aerosol–cloud interactions. Such retrievals, however, rely on forward radiative transfer (RT) calculations using simplified assumptions that can lead to retrieval errors when the real atmosphere deviates from the forward model. Here, coincident airborne remote sensing and in situ observations obtained during NASA's ObseRvations of Aerosols above CLouds and their intEractionS (ORACLES) field campaign are used to evaluate retrievals of CER for marine boundary layer stratocumulus clouds and to explore impacts of forward RT model assumptions and other confounding factors. Specifically, spectral CER retrievals from the Enhanced MODIS Airborne Simulator (eMAS) and the Research Scanning Polarimeter (RSP) are compared with polarimetric retrievals from RSP and with CER derived from droplet size distributions (DSDs) observed by the Phase Doppler Interferometer (PDI) and a combination of the Cloud and Aerosol Spectrometer (CAS) and the Two-Dimensional Stereo Probe (2D-S). The sensitivities of the eMAS and RSP spectral retrievals to assumptions about the DSD effective variance (CEV) and liquid water complex index of refraction are explored. CER and CEV inferred from eMAS spectral reflectance observations of the backscatter glory provide additional context for the spectral CER retrievals. The spectral and polarimetric CER retrieval agreement is case dependent, and updating the retrieval RT assumptions, including using RSP polarimetric CEV retrievals as a constraint, yields mixed results that are tied to differing sensitivities to vertical heterogeneity. Moreover, the in situ cloud probes, often used as the benchmark for remote sensing CER retrieval assessments, themselves do not agree, with PDI DSDs yielding CER values 1.3–1.6 µm larger than CAS and with CEV roughly 50 %–60 % smaller than CAS. Implications for the interpretation of spectral and polarimetric CER retrievals and their agreement are discussed.

Meyer, Kerry [NASA Goddard Space Flight Center (GS↗

DOE OSTI2025

SiC Receiver/Reactor by Additive Manufacturing for Concentrated Solar Thermocatalysis with Thermal Energy Storage (Final Technical Report - Public)

The direct use of solar thermal energy provides opportunities for low-cost heating sources for a variety of applications. Ultra-high temperatures around 1000°C are high value and highly useful for energy-demanding industries. Many materials cannot withstand these conditions. In the area of Sustainable Chemicals, further limitations on material stability exist. Combining state-of-the-art materials with new designs provides a promising pathway for harvesting solar thermal energy and performing high temperature chemical processes. However, conventional manufacturing limits the potential for design flexibility. In this project, Additive Manufacturing was combined with advanced materials and new chemical reactor designs. In addition, 24/7 energy is necessary for chemical processing, and designs for ultra-high temperature thermal storage were devised. Specifically, preliminary design of a novel solar thermal receiver was developed in this project and designed to work with thermocatalytic reactors for producing sustainable chemicals and fuels. An ultra-high temperature particle storage system and heat exchangers were proposed to transport ultra-hot air as thermal fluid for the system. On a broader scale, this system could be used to tap solar thermal energy for a centralized facility with capability of transferring that heat to various segments at a full range of temperatures to 1000°C. The project pushed the temperature boundaries past those in current use, and Additive Manufacturing was envisaged for fabricating the receiver to meet requirements of extreme environments. An extensive analysis of silicon carbide additive manufacturing was performed to compare the thermal and mechanical properties of complex geometries compared to conventional material and those manufactured via other methods. The Additive Manufacturing via Binder-Jet printing was optimized and characterized to provide high quality and reproducible components capable of withstanding the proposed extreme environments. The designs for the concentrating solar thermal cavity with ultra-hot air thermal fluid showed high performance in simulations, attributable to the complex optimized geometries of the 3D printed systems. The bright future of Additive Manufacturing with advanced materials developments should provide more options and even higher quality as the technology further develops. Current costs for Additive Manufacturing of advanced ceramics is relatively low, however post-processing of the materials for extreme environments is currently high. There is little industrial-scale infrastructure for these, but it is growing as niche applications become more mainstream. The results of the project can be translated into similar extreme environments for concentrating solar thermal energy as well as its integration with ultra-hot air thermal fluids. A number of industries that require ultra-high temperatures need to electrify or otherwise decarbonize for climate goals, and this project showed that theoretically there is a pathway to do so with direct concentrated solar thermal power.

10 SYNTHETIC FUELS↗

DOE OSTI2025

Dataset: "Widespread Drought-driven Declines in Streamflows and Water quality in the Upper Colorado River Basin (1998-2022)"

This data package contains the associated data and scripts for Nagamoto, E., Ombadi, M., Ciulla, F. et al. Widespread drought-driven declines in streamflows and water quality in the Upper Colorado River Basin during 1998-2022. Commun Earth Environ 7, 734 (2026). https://doi.org/10.1038/s43247-026-03890-5. This purpose of this study was to investigate the impact of the 21st century drought on water quantity and quality at catchments throughout the Upper Colorado River Basin (UCRB). We used stream flow, water temperature, specific conductance, air temperature, precipitation, and catchment attribute data for over 200 sites in the UCRB, collected from the National Water Information System using Basin3D (Varadharajan, 2023), GAGESII (Falcone, 2010), and the Google Earth Engine. We identified years of severe drought between 1998 and 2022 using the Standardized Precipitation Evaporation Index (SPEI), then calculated the relative change percentage of the stream flow, water temperature, and specific conductance from drought versus non-drought years. We used the attribute information from GAGESII to investigate what physical traits of catchments are associated streamflow vulnerability (greater relative change) or resilience to drought. We used land cover data from the National Land Cover Database (USGS, 2024) to assess any changes to physical attributes that may not be represented in the static attributes information in GAGESII. To increase data availability, we modeled stream temperature using methods from Willard, 2023. While the study period is water years 1998 to 2022, the raw water quantity and quality data extends to 1950 and the meteorological data extends to 1980. The data and code can be downloaded via the UCRB_drought.zip. Within the zip, the files are organized as follows: - INPUTS: Contains all input data used in UCRB_Drought_Workflow.ipynb - OUTPUTS: Contains all intermediate data created from UCRB_Drought_Workflow.ipynb as well as final products including the calculated Standardized Evapotranspiration Index (SPEI) - climatic_variables: The code used to collect meteorologic data from Google Earth Engine - feature_importance: The code used for the catchment attributes analysis - preprocessing: Code used in UCRB_Drought_Workflow_Preprocessing.ipynb - pyeto: Code used in UCRB_Drought_Workflow_Preprocessing.ipynb - calculations: Code used in UCRB_Drought_Workflow_Impacts.ipynb - plotting: Code used in UCRB_Drought_Workflow_Impacts.ipynb - README.md - UCRB_Drought_Workflow_Preprocessing.ipynb: The code used to prep raw data for the analysis - UCRB_Drought_Workflow_Impact.ipynb: The code which uses the prepped raw data for analysis, and plots all figures - requirements_ucrb-drought_v2.yml: The requirements file to create a virtual environment and Jupyter Lab kernel to run the code The INPUTS folder is organized into the following major directories and sub-directories. The "RDC_WT_SC_RAW" folder contains raw data for streamflow, water temperature, and specific conductance in a ".h5" file. The "NLCD_RAW" folder contains ".csv" files with annual land cover percentages for counties within the UCRB. The "MET_RAW" folder contains a ".csv" file with monthly meteorological data (air temperature and precipitation) for the sites in the UCRB which was obtained from code in the climatic_variables folder. The "GAGESII" folder contains ".csv" files with physical catchment attribute variables for catchments across the country. The "WT_LSTM_data" folder contains ".csv" files with calculated WT (Willard, 2023) and the associated RMSEs. The "Upper_Colorado_River_Basin_Boundary" folder contains geographic data including a shapefile for plotting in the UCRB_Drought_Workflow.ipynb. The "RESERVOIRS_RAW" folder contains ".csv" files for each reservoir in the UCRB with daily reservoir storage. There are also two files in the INPUTS folder that have combined reservoir storage data and reservoir metadata. The OUTPUTS folder is organized into the following major directories and sub-directories. The "RDC_WT_SC_data" folder contains a folder "Water_year" with the associated cleaned data, metadata, and data availability information in ".csv" files, a folder "Median_Relchange" with the relative change comparing drought to non-drought years in ".csv" files, and a folder "Peak95_Min5_Relchange" that has ".csv" files for the relative change in peak (95th %) and minimum (5th %) variables. The "NLCD_data" folder contains the difference in land cover from the beginning to end of the study period and the percentage of the county that is within UCRB bounds can be found in Nagamoto et al (2025)). The "MET_data" folder contains separated monthly air temperature and precipitation data and the calculated PET in ".csv" files. The "SPEI_data" folder contains ".csv" files with calculated SPEI values (one restricted to the study period and the other with information from the entire MET data period). The "Paper_Tables" folder contains two ".csv" files containing site information and data availability and information about the GAGESII trait aggregated categories. The base directory includes the file “flmd.csv” for a list and description of all files and the file “dd.csv” for data dictionaries. Scripts for preprocessing, analysis, and figure generation are located in the associated GitHub repository found at [https://github.com/iNAIADS/drought-impacts/tree/develop/UCRB-drought]. UPDATE 1: Title and code file updated to match submitted manuscript 10-15-2025. UPDATE 2: Code and data files updated to match revised manuscript 3-4-2026. UPDATE 3: Code and data files updated to match revised manuscript 6-7-2026. ** NOTE: DD and FLMD have not been updated yet. UPDATE 4: Added associated Manuscript information and DD and FLMD have been updated. To cite this code, please use the following BibTeX: @misc{nagamoto2025drought, author = {Emily Nagamoto and Fabio Ciulla and Mohammad Ombadi and Jared Willard and Rosemary Carroll and Charuleka Varadharajan}, title = {Dataset: "Widespread Drought-driven Declines in Streamflows and Water quality in the Upper Colorado River Basin (1998-2022)"}, year = {2025}, doi = {10.15485/2551894}, publisher = {ESS-DIVE Repository}, url = {https://data.ess-dive.lbl.gov/datasets/doi:10.15485/2551894} }

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2026

Thermal Performance of Spandrel Assemblies in Glazed Wall Systems: Laboratory Test Design – Challenges and Test Results

Accurate thermal performance calculation procedures for opaque spandrel areas in curtain wall and window wall systems are essential for rating systems when comparing spandrel systems. However, there is a lack of consensus in thermal modeling needed for accurately characterizing heat transfer through spandrel assemblies due to the complex arrangement of materials and structural components. Several studies indicate that conventional 2D thermal simulations may overestimate R-values by 30% compared to physical testing and 3D simulations. Detailed simulations and well-curated laboratory test data are necessary to build confidence in simulation models, which will later be used to develop correlations to improve widely used conventional 2D thermal simulations. This study aims to experimentally test heat transfer through various spandrel assemblies to validate 3D simulation models. Also, the challenges of conducting a thorough testing design along with the solutions would be documented. The team developed a design for testing spandrel assemblies, making appropriate modifications to the existing heat, air, and moisture (HAM) chamber to accommodate the testing needs. Two moveable baffles were designed and fabricated to guide airflow direction parallel to the test article surface. The data acquisition capabilities in the chamber were upgraded to add more than two hundred sensors to the climate and indoor side of the chamber. The goal is to provide a quality dataset for validating complex 3D modeling simulations, which will be used to develop improved thermal simulation techniques that more accurately represent the thermal behavior of spandrel assemblies and their integration within the building envelope. This paper will summarize the results for the boundary conditions of the testing and the temperature variation across different locations of the spandrel assemblies.

Kunwar, Niraj [ORNL] (ORCID:0000000263457652)↗

DOE OSTI2024

Urban morphology and urban water demand evolution in the Los Angeles region

Detailed description of the dataset sources used in this study, the experimental workflow, and plotting for the paper figures provided at the associated GitHub Meta Repo: https://github.com/IMMM-SFA/Ferencz_et_al_2024_ERL The future water demand projections from this study are hypothetical future water demands that reflect the population and urban land cover changes represented by the scenarios considered. The intent and emphasis of this work is investigating the interactions between population change, evolution of urban morphology, and water demand. These projections are not meant to be likely future demands for specific water providers or the LA region and should not be interpreted as such. The folders contain input and output data for each step of the "Recreate my Experiment" workflow described in the associated GitHub meta-repository as well as data used for plotting Figures for the paper that this dataset supports. Description of each folder's contents and use: Step_1a: Inputs to the associated python script provided on the GitHub repo. Step_1b: Inputs (downscaled population rasters) used by the associated python script provided on the GitHub repo. Original 1-km squared rasters that were downscaled also provided. Step_1c: Urban growth projection rasters corresponding to SSP3 and SSP5 population scenarios are provided in separate subfolders as well as the water provider boundaries used for analysis. Outputs of data processing also provided. Associated python script provided on GitHub. Step_1d: Description of Inputs used by the QGIS Model Builder GUI that automates geospatial processing and clipping the of the high-resolution 60 cm land cover data for each urban land class footprint within a defined polygon boundary. The Model Builder is provided on the GitHub repo and can be used by QGIS. The outputs of this step are in "Clipped Provider Hi Res Landcover". If the user wants to use The Model Builder for different regions of LA or to test our outputs, they will need to download the hi resolution landcover raster listed in the Readme and in Ref [2] of the GitHub Page. Step_1e: All necessary inputs to generate average monthly demand over the 2017-2021 period and the minimum and maximum demands over the 2014-2021 for each water provider. Associated python scripts are on GitHub. Step 2: Output data about land cover metrics (areas and fractions) for each urban land class for each water provider. Associated python script on GitHub. Uses outputs from Step 1d "Clipped Provider Hi Res Landcover" Step 3: Both the Inputs for and Outputs from the urban projection raster analysis Python script on GitHub. The inputs are urban land class rasters for specific SSP and zoning scenarios (low, medium, high) from Step 1c. The outputs are rasters of urban pixels that were converted to a higher land class and the number of land class units that changed (Values of 1, 2, or 3). For example, a value of 2 could be LC 21 -> 23 or LC 22 -> 24. These maps are label "intensification." The other outputs are "urban growth" rasters showing the conversion of non urban to urban land, which are indicated by pixel values of 1. These are used for the urban growth change maps in Figure 3. Step 4: Output projections of indoor and outdoor annual and monthly demands for each water provider for the average, minimum, and maximum monthly demand scenarios for each of the four urban growth scenarios (SSP3 med, SSP5 low, SSP5 med, and SSP5 high). The outputs also include metrics on each water provider used for the demand sensitivity analysis presented in Figure 8. Outputs from Step 4 are used for Figures 4 - 8 of the paper. Figures: This folder has data used for plotting Figures 1 through 5, and 8. Data for Figures 6 and 7 are sourced directly from folders associated with the Processing and Analysis Steps 1 - 4. The GitHub meta repository provides descriptions of how each figure was made and the associated plotting scripts used.

Los Angeles↗

DOE OSTI2025

Propagating information content: an example with advection

The mathematical algorithm to derive geophysical information from remote sensing observations is called a retrieval. The mathematics of many retrieval problems are ill-posed, and thus a priori information is used to help constrain the derived geophysical variable to realistic values. One quantity of interest, therefore, is the information content of the observation. Perfect information content in the observation would be achieved if the retrieval were able to capture any perturbation in the desired geophysical variable with the proper magnitude. Many new data products can be derived by combining geophysical variables retrieved from multiple different remote sensors. This paper explores, for the first time, how to derive the information content of these derived products. The approach uses traditional error propagation techniques to derive the uncertainty of the derived field twice, both when the observations are used in the retrieval and also when only the a priori information from each remote sensor is propagated. These two uncertainties are then used to provide an estimate of the information content of the derived geophysical variable. This study demonstrates how to propagate the uncertainties from six different instruments to provide the information content for water vapor and temperature advection. A multi-month analysis demonstrates that, in a mean sense, the information content for temperature advection is nearly unity for all heights below 700 m while, the information content for water vapor advection is somewhat more variable but still larger than 0.6 in the convective boundary layer.

Turner, David D. [National Oceanic and Atmospheric↗

DOE OSTI2026

Sub-Nanometer Nanoclusters of Copper Atop Single-Atom Copper Moieties toward Electrochemical CO 2 Hydrogenation to Methane

The electrochemical CO 2 reduction (eCO 2 R) offers a compelling route for converting CO 2 into value-added fuels and chemicals. Among CO 2 -derived products, methane (CH 4 ) occupies a distinct position, serving both as a key intermediate for emerging cascade electro-oxidation to oxygenates and as a strategically important extraterrestrial fuel that can be generated in situ from off-planet CO 2 resources. Although Cu-based catalysts capable of selectively producing CH 4 have been reported, they seldom sustain high selectivity at practically relevant current densities. Here, we created a single-step co-pyrolysis strategy toward generating and anchoring Cu sub-nanometer clusters (Cu SNC ) atop Cu-N x single-atom (SA) motifs embedded within N-doped carbon (NC), with controllable nanostructures through tuning of the synthesis parameters. Complementary spectroscopic analyses and density functional theory (DFT) calculations help reveal a structure−activity correlation that could guide the catalyst design. The Cu SNC @NC sample synthesized at 550 °C pyrolysis temperature (best described and modeled as Cu 3 -CuN 4 domains) represents the most effective combination of cluster size, metal-nitrogen coordination, and adsorption energetics needed to selectively promote CH 4 generation versus other eCO 2 R products. Incorporating pulsed electrolysis and hydrophobicity-modulated transport tuning at the triple-phase boundary (TPB) further enhanced CH 4 production achieving a partial CH 4 current density of ∼321 mA cm −2 , 53% Faradaic efficiency (FECH 4 ), and less than 4% combined FE for other eCO 2 R products, simplifying downstream CH 4 purification or upgrading. This work establishes generalizable principles for controlling Cu cluster atomicity and metal−nitrogen coordination, both of which are recognized determinants of CH 4 -efficient eCO 2 R.

CH4 production↗

DOE OSTI2025

Molecular-dynamics study of diffusional creep in uranium mononitride

Uranium mononitride (UN) is a promising advanced nuclear fuel due to its high thermal conductivity and high fissile density. Yet, many aspects of its mechanical behavior and microstructural features are currently unknown. In this paper, molecular dynamics (MD) simulations are used to study UN's diffusional creep. Nanometer-sized polycrystals are used to simulate diffusional creep and to calculate an effective GB width. It is found that Nabarro-Herring creep is not dominant in the temperature range of 1700–2000 K and that the dominant diffusional creep mechanism is Coble creep with an activation energy of 2.28 ± 0.09 eV. A method is proposed to calculate the diffusional GB width and its temperature dependence in polycrystals. The effective GB width of UN is calculated as 2.69 ± 0.08 nm. This value fits very well with the prefactor of the phenomenological Coble creep formula. It is demonstrated that the most comprehensive thermal creep model for UN can be represented as the combination of our Coble creep model and the dislocation creep model proposed by Hayes et al.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗