SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
LGGUN is a quasi-one-dimensional Godunov code1 which is second order accurate in time and third order accurate in space, uses realistic equations of state for all media, includes wall friction and heat transfer for all gas and dense media zones and includes a simple non-equilibrium model for gas phase turbulence. This manual details the theory and operation of the code.
• Need for data at muzzle velocities of 7.0 km/s and above to simulate impacts of space debris and naturally occurring meteoroids • The two-stage light gas gun is a well known way of achieving these velocities • There is a danger of significant swelling and even bursting of the HPC (high pressure coupling). • A consistent picture of the swelling and bursting of the HPCs of two Ames two-stage light gas guns is developed, based on the following: 1. Experimental measurements of the swelling and bursting of the HPCs of two two-stage light gas guns. 2. Stress-strain calculations of the swelling and bursting of thick walled steel tubes. 3. Experimental measurements swelling and bursting of thick walled steel tubes. 4. CFD calculations of the maximum pressures in the HPC of a two-stage light gas gun using the code LGGUN. • It is shown that model developed predicts swelling and bursting that agrees reasonably well with measured data. • Hence, it is suggested that the model could be used in the design of a two-stage light gas guns to assess the risk of swelling and bursting and to give maximum suggested operating conditions for an existing gun.
This work focused on the effects on turbulent heat transfer due to surface roughness of types relevant to NASA entry missions, and was supported by NASA’s Entry Systems Modeling (ESM) Project. The emphasis was on new classes of woven materials, which are enabling for many missions.
The effective aerodynamic characteristics for the debris resulting from the Space Shuttle External Tank (ET) are required for estimating the impact points of the debris. The paper develops a methodology that determines the effective values of the aerodynamic parameters required for performing the less complex three-degree-of-freedom (DOF) debris impact analyses. For all of the debris types, 6-DOF mass property and aerodynamic data are computed. From many 6-DOF trajectory simulations, standard deviation range values are calculated. With 3-DOF trajectory matching, these range values are used to determine the effective ballistic coefficient and the range of lift-to-drag ratios for each of the ET debris types defined.
The present study considers direct ballistic entries into the atmosphere of Venus using a 45deg sphere-cone rigid aeroshell, a legacy shape that has been used successfully in the past in the Pioneer Venus Multiprobe Mission. For a number of entry mass and heatshield diameter combinations (i.e., various ballistic coefficients) and entry velocities, the trajectory space in terms of entry flight path angles between skip out and -30deg is explored with a 3DoF trajectory code, TRAJ. From these trajectories, the viable entry flight path angle space is determined through the use of mechanical and thermal performance limits on the thermal protection material and science payload; the thermal protection material of choice is entry-grade carbon phenolic, for which a material thermal response model is available. For mechanical performance, a 200 g limit is placed on the peak deceleration load experienced by the science instruments, and 10 bar is assumed as the pressure limit for entry-grade carbon-phenolic material. For thermal performance, inflection points in the total heat load distribution are used as cut off criteria. Analysis of the results shows the existence of a range of critical ballistic coefficients beyond which the steepest possible entries are determined by the pressure limit of the material rather than the deceleration load limit.
Fabry-Perot microcavities can strongly enhance interactions between light and molecules, leading to the formation of hybrid light-matter states known as polaritons. Polaritons possess much smaller effective masses and much larger group velocities when the molecules are resonant with cavity modes that have finite (nonzero) in-plane wave vectors, giving rise to the possibilities of long-range and ultrafast ballistic transport. In this paper, we present the results of numerical simulations of the ultrafast ballistic transport phenomenon in real space and time during and after initialization with a short, spatially localized pulse. Here, we address this problem with two approaches: the standard transfer-matrix method (TMM) for planar structures and a second simulation based on the numerical solution of the Maxwell-Bloch equations that can be used for general configurations (complex metasurfaces, for instance) and excitation modes. The agreement between the TMM and the full numerical calculation with the Maxwell-Bloch equations when applied to multilayer planar configurations provides proof of the validity of both approaches for the present analyses. Overall, we find that the transport of the molecular excitons inside the cavity synchronize with the evolution of the enhanced electromagnetic field inside the cavity. Moreover, the synchronized transport rate is in good agreement with the group velocities predicted from a calculated dispersion relation across a wide range of frequencies. Finally, we relate the group velocity to the Hopfield coefficient obtained from quantum modeling and suggest that the dependence of light-matter coupling on the in-plane wave vector can be an important but overlooked factor for understanding the transport behavior of polaritons. These simulations provide an intuitive tool for understanding the collective motion of light and excitons and helps us to better understand how experimental observations of polaritons should be interpreted.
A multi-disciplinary research program was recently completed, sponsored by NASA Marshall Space Flight Center, on the subject of aerocapture of spacecraft weighing up to 5 metric tons at Mars. Heavier spacecraft will require deployable drag area beyond the dimensional limits of current and planned launch fairings. This research focuses on the approach of lightweight inflatable decelerators constructed with thin films, using fiber reinforcement and having a temperature limitation of 500 C. Trajectory analysis defines trajectories for a range of low ballistic coefficients for which convective heat flux is compatible with the material set. Fluid-Structure Interaction (FSI) tools are expanded to include the rarified flow regime. Several non-symmetrical configurations are evaluated for their capability to develop lift as part of the necessary trajectory control strategy. Manufacturing technology is developed for 3-D stretch forming of polyimide films and for tailored fiber reinforcement of thin films. Finally, the mass of the decelerator is estimated and compared to the mass of a traditional rigid aeroshell.
The interaction between crater ejecta and the transient wind from impact-shock vaporization is discussed. Based partly on Shoemaker's (1962) ballistic model of the Copernicus ejecta and partly on Rehfuss' (1972) treatment of lunar winds, a simple model is developed which indicates that if Copernicus were formed by a basaltic meteorite impacting at 20 km/s, then 3% of the ejecta mass would be sent beyond the maximum range expected from purely ballistic trajectories. That 3% mass would, however, shift the position of the outer edge of the ejecta blanket more than 400% beyond the edge of the ballistic blanket. For planetary bodies lacking an intrinsic atmosphere, the present model indicates that this form of hyperballistic transport can be very significant for small (no more than about 1 kg) ejecta fragments.
To better understand the technology requirements for a Uranus atmospheric entry probe, an internal NASA study was conducted. The main objectives for this study were: (1) to determine the entry trade space through parametric studies; and (2) to identify entry technologies that could be used to enable a mission that would meet at least the Tier 1 science objectives described in the Decadal Survey. The paper describes two different approaches to the planet: 1) direct ballistic entry 2) aerocapture followed by direct entry of probe. For direct ballistic entry the trajectory analyses were performed for a range of entry flight path angles and ballistic coefficients. The larger size probes was also considered in an attempt to enable Tier 2 science objectives. For aerocapture analysis a single case was studied to demonstrate feasibility and benefits with this option. A summary of all of the above analyses, including factors that constrain allowable entry trajectories, is presented
The Impact Testing Facility (ITF) serves as an important installation for materials science at Marshall Space Flight Center (MSFC). With an array of air, powder, and two-stage light gas guns, a variety of projectile and target types and sizes can be accommodated. The ITF allows for simulation of impactors from rain to micrometeoroids and orbital debris on materials being investigated for space, atmospheric, and ground use. Expendable, relatively simple launch assemblies are used to obtain well-documented results for impact conditions comparable to those from ballistic and rocket sled ranges at considerably lower cost. In addition, for applications requiring study of impacts at speeds in excess of those attainable by gun launches, hydrocode simulations, validated by test data, can be used to extend the velocity range. In addition to serving various NASA directorates, the ITF has performed testing on behalf of the European and Russian space agencies, as well as the Department of Defense, and academic institutions. The m s contributions not only enable safer space flight for NASA s astronauts, but can help design materials and structures to protect soldiers and civilians on Earth, through advances in body armor, aircraft survivability, and a variety of other applications.
Shielding a spacecraft from the severe thermal environment of an atmospheric entry requires a sophisticated thermal protection system (TPS). Thermal computer program models were developed for two such TPS designs proposed for the space shuttle orbiter. The multilayer systems, a reusable surface insulation TPS, and a re-radiative metallic skin TPS, were sized for a cross-section of trajectories in the entry corridor. This analysis indicates the relative influence of the entry parameters on the weight of each TPS concept. The results are summarized graphically. The trajectory variables considered were down-range, cross-range, orbit inclination, entry interface velocity and flight path angle, maximum heating rate level, angle of attack, and ballistic coefficient. Variations in cross-range and flight path angle over the ranges considered had virtually no effect on the required entry TPS weight. The TPS weight was significantly more sensitive to variations in angle of attack than to dispersions in the other trajectory considered.
Early in calendar year 1958 Space Technology Laboratories, Inc. (STL) (then Space Technology Laboratories, a division of the Ramo-Wooldridge Corp.) developed for the Air Force Ballistic Missile Division (AFBMD) an Advanced Re-entry Test Vehicle (ARTV) for the purpose of testing ballistic missile nose cones at the full range of 5500 nautical miles. The two-stage ARTV utilized the Thor ballistic missile and the second stage propulsion system developed for the Vanguard program. In late 1957 and early 1958, STL/AFBMD prepared studies of various missile combinations which could be utilized for space testing. The Thor, in combination with the Vanguard second and third stages, was one of the vehicles considered which offered a very early capability of placing a reasonable payload in a lunar orbit. These STL/AFBMD studies were presented to various appropriate groups including the Killian, Millikan, H. J . Stewart Committees; Headquarters, Air Research and Development Command, and ARDC Centers. Subsequently the Advanced Research Projects Agency (ARPA) contacted STL relative to the availability of hardware for an early lunar shot. By utilizing existing spares already purchased for the ARTV, and by making use of the ARTV contractors already in being, it appeared feasible to launch by the third quarter of calendar year 1958 a payload which would be captured by the moon's gravitational force. On 27 March 1958, ARPA directed STL to proceed with a program of three lunar shots. As much as possible, these shots were to utilize existing ARTV spare hardware and impose no interference with the ballistic missile programs. In September this program was transferred to the direction of the National Aeronautics and Space Administration (NASA). On 17 August 1958 the first launching of the Able-1 vehicle was attempted, but the flight was terminated by a propulsion failure of the first stage. Subsequent launchings were attempted on 13 October and 8 November 1958. Of these launchirigs the October attempt was the most successful. Although the payload did not reach the vicinity of the moon, a maximum altitude of 71,700 was attained, and useful scientific data was obtained from the instrumentation.
The environments produced by entry into Jupiter and Saturn atmospheres are summarized. Worst case design environments are identified and the effect of entry angle, type of atmosphere and ballistic coefficient variations are presented. The range of environments experienced during earth entry is parametrically described as a function of initial entry conditions. The sensitivity of these environments to vehicle ballistic coefficient and nose radius is also shown. An elliptical deorbit maneuver strategy is defined in terms of the velocity increment required versus initial entry conditions and apoapsis altitude. Mission time, ground track, and out of plane velocity penalties are also presented. Performance capabilities of typical shuttle launched boosters are described including the initial entry conditions attainable as a function of paylaod mass and apoapsis altitude.
A parametric study of ballistic modifications to the 120 inch diameter solid propellant rocket engine which forms part of the Air Force Titan 3 system is presented. 576 separate designs were defined and 24 were selected for detailed analysis. Detailed design descriptions, ballistic performance, and mass property data were prepared for each design. It was determined that a relatively simple change in design parameters could provide a wide range of solid propellant rocket engine ballistic characteristics for future launch vehicle applications.
Contents of this issue are: (1) Energy-Based Tetrahedron Sensor for High-Temperature, High-Pressure Environments (2) Handheld Universal Diagnostic Sensor (3) Large-Area Vacuum Ultraviolet Sensors (4) Fiber Bragg Grating Sensor System for Monitoring Smart Composite Aerospace Structures (5) Health-Enabled Smart Sensor Fusion Technology (6) Extended-Range Passive RFID and Sensor Tags (7) Hybrid Collaborative Learning for Classification and Clustering in Sensor Networks (8) Self-Healing, Inflatable, Rigidizable Shelter (9) Improvements in Cold-Plate Fabrication (10) Technique for Radiometer and Antenna Array Calibration - TRAAC (11) Real-Time Cognitive Computing Architecture for Data Fusion in a Dynamic Environment (12) Programmable Digital Controller (13) Use of CCSDS Packets Over SpaceWire to Control Hardware (14) Key Decision Record Creation and Approval Module (15) Enhanced Graphics for Extended Scale Range (16) Debris Examination Using Ballistic and Radar Integrated Software (17) Data Distribution System (DDS) and Solar Dynamic Observatory Ground Station (SDOGS) (18) Integration Manager (19) Eclipse-Free-Time Assessment Tool for IRIS (20) Automated and Manual Rocket Crater Measurement Software (21) MATLAB Stability and Control Toolbox Trim and Static Stability Module (22) Patched Conic Trajectory Code (23) Ring Image Analyzer (24) SureTrak Probability of Impact Display (25) Implementation of a Non-Metallic Barrier in an Electric Motor (26) Multi-Mission Radioisotope Thermoelectric Generator Heat Exchangers for the Mars Science Laboratory Rover (27) Uniform Dust Distributor for Testing Radiative Emittance of Dust-Coated Surfaces (28) MicroProbe Small Unmanned Aerial System (29) Highly Stable and Active Catalyst for Sabatier Reactions (30) Better Proton-Conducting Polymers for Fuel-Cell Membranes (31) CCD Camera Lens Interface for Real-Time Theodolite Alignment (32) Peregrine 100-km Sounding Rocket Project (33) SOFIA Closed- and Open-Door Aerodynamic Analyses (34) Sonic Thermometer for High-Altitude Balloons (35) Near-Infrared Photon-Counting Camera for High-Sensitivity Observations (36) Integrated Optics Achromatic Nuller for Stellar Interferometry (37) High-Speed Digital Interferometry (38) Ultra-Miniature Lidar Scanner for Launch Range Data Collection (39) Shape and Color Features for Object Recognition Search (40) Explanation Capabilities for Behavior-Based Robot Control (41) A DNA-Inspired Encryption Methodology for Secure, Mobile Ad Hoc Networks (42) Quality Control Method for a Micro-Nano-Channel Microfabricated Device (43) Corner-Cube Retroreflector Instrument for Advanced Lunar Laser Ranging (44) Electrospray Collection of Lunar Dust (45) Fabrication of a Kilopixel Array of Superconducting Microcalorimeters with Microstripline Wiring Spacecraft Attitude Tracking and Maneuver Using Combined Magnetic Actuators (46) Coherent Detector for Near-Angle Scattering and Polarization Characterization of Telescope Mirror Coatings
The SARS-CoV-2 pandemic has heightened the interest in particle-laden turbulent jets generated by breathing, talking, coughing and sneezing, and how these can contribute to disease transmission. We present quantitative measurement methods for such flows, while exploring and offering improvements for common shortcomings. We generate jets consisting of either liquid droplets or solid particles in an isothermal, quiescent and electrically isopotential experimental chamber that was constructed to control the effects of ambient forcing on jet behavior. For liquid droplets, we find promise in surface deposition analysis based on fluorescent tracer use. For particles, we explore the performance of commercially available adhesive sampling strips and develop conductive grounded carbon tape based sampling strips. We explore ways in which the smallest of thermal gradients or electrostatic charge issues can affect particle dispersion, and suggest practical methods to address these issues. The developed methods are applied to study the simultaneous deposition of (Formula presented.) 25, 50 and 200 μm solid particles from a particle laden turbulent jet with a mean velocity of 33.2 m/s. The deposition location as a function of particle size was compared to results from a simple numerical RANS model, and illustrates ways in which imprecise initial or boundary conditions can lead to a notable deviation from experimental results. The differences in deposition pattern seen in experimental and numerical results despite a carefully controlled environment and characterized particle ejection indicate the need for a more stringent numerical model validation, especially when studying fate and transport of mid-range (neither purely aerosol or ballistic) sized particles.
As part of an effort to improve the state-of-the-art in nozzle technology, a solid propulsion test bed facility is being designed and will be located at Marshall Space Flight Center. The test bed will consist of a plasma arc facility and several small scale rocket motor test facilities ranging in size from the ballistic environmental generator motor with a 1/2 in. diameter throat to the MNASA motor with a 9 and 1/2 in. diameter throat capability. The test bed system will be used primarily to study materials behavior from the standpoint of char, erosion, and thermal stress phenomena.
Computational Fluid Dynamics (CFD) analysis was used to compute effective nozzle discharge coefficients for subscale sharp-edged converging/diverging nozzles, with a variety of convergence half-angles, motor operating conditions, and two propellants with different ballistics. Convergence half-angles ranged from 0 to 80 deg. Analysis was conducted at total temperatures from 2946K (5303R) to 3346K (6023R) and over total pressures ranged from 2.72 MPa (395 psia) to 20.68 MPa (3000 psia). Area ratios (A(sub e)/A*) ranged from 7.43 to 9.39. Ratio of specific heats (gamma) ranged from 1.13 to 1.18. Throat and exit Reynolds numbers were calculated to be 8.26 x 10(exp 5) and 5.51 x 10(exp 5), respectively. Present results of nozzle discharge coefficients are reported and correlated as a function of nozzle convergence half-angle (theta(sub c)) and area ratios (A(sub e)/A*) for a constant divergence half-angle (theta(sub d)) of 15 deg. Computed discharge coefficients ranged from 0.88 to 0.97. They are compared with theory and experimental data available in literature. Available turbulence models with respect to grid refinements and heat transfer are discussed.