Search NASA⌕ Search

SEARCH · Search NASA

Results for “Base”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Impedance-Based Prediction of SSR-Generated Harmonics in Doubly-Fed Induction Generators

Doubly-fed induction generators (DFIGs) are prone to subsynchronous resonance (SSR) with series-compensated transmission lines and experiencing SSR-generated harmonics of wide-ranging magnitudes. This paper presents a large-signal impedance-based approach for the prediction of the magnitude of SSR-generated harmonics in DFIGs. Note that the large-signal impedance of a network shows variation in its impedance response with the magnitude of perturbation at its terminals. It is discovered in this paper that the impedance of a series-compen- sated transmission line starts changing with the magnitude of SSR because of the metal-oxide varistor-based protection of series capacitors in the line. The changing line impedance halts the growth of the SSR beyond a certain point, where the DFIG forms a limit-cycle mode and emits harmonics at the SSR frequency. The discovered role of the protection of series capacitors in SSR not only enables the prediction of SSR-generated harmonics but also can be used for the timely detection of an SSR event to avoid system disruption and sudden loss of bulk generation. The large- signal impedance-based prediction of SSR-generated harmonics in DFIG-based wind and hydro generators is demonstrated using numerical simulations of a 2.5-MVA, 690-V DFIG supplying to a series-compensated transmission line.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2021

EMI Mitigation of a Ćuk-Based Power-Electronic System Using Switching-Sequence-Based Control

Switching-sequence-based control (SBC) laws when designed based on topological switching behavior can have positive effects on slow- and fast-scale dynamics of a power-electronic system (PES). The slow-scale control can encompass fast PES state regulation and tracking, based on predefined objective, while fastscale control can address differential-mode (DM) and commonmode (CM) spectral-peak energy associated with PES switching operation. Such control laws may offer enhanced programmability to conventional PES design where bulky electromagnetic interference (EMI) filters have been traditionally used to reduce EMI of switching power converters to meet EMI regulatory standards. An EMI filter is always a less programmable solution since it is usually designed for the worst-case EMI mitigation and usually overkill for a PES operating under reduced load condition. The control scheme outlined in this article offers EMI mitigation across wide operating regions without compromising PES regulation. Moreover, it does so by use of switching sequences that guarantee the reachability of the PES dynamics using an advanced Lyapunov-function-based approach. SBC is a powerful tool to generate control actions for a PES based on multivariate PES state constraints. Hence, contemporary EMI regulatory standards are used as constraints in the SBC formulation to operate the PES under wide operating regime while autonomously mitigating the EMI levels. The work may be of paramount importance for operating the ultra-fast-transition recent wide-bandgap semiconductor devices like GaN–FET and SiC MOSFET under higher power with increasing switching frequencies, which is usually desirable for increased power density and reduced switching losses. Here, a hardware Cuk–PES operated ´ with GaN–FETs is fabricated and is used for case illustration. It is shown by experimental results how SBC mitigate DM and CM EMI noise of the PES while maintaining regulation even for the higher order nonminimum phase PES, while reducing sensor requirements using state observer derived from the switching model of the PES.

42 ENGINEERING↗
NASA NTRS2021

A Ground-Delay-Based Approach to Reduce Impedance-Based Airspace Complexity

This paper introduces a ground-delay-based traffic management approach to reduce the impedance-based airspace complexity for a given scenario. This work extends our prior research on developing an impedance-based complexity metric for unmanned aircraft system traffic scenario classification. Impedance-based metric was evaluated for 1045 randomly generated scenarios. Scenarios with overall impedance above a certain threshold were declared as not feasible. A ground-delay-based approach was developed to be applied to the rest of the scenarios so as to remediate any scenarios with small areas of high impedance on their impedance maps. A sample application is shown for a scenario with sixty flights. The detailed trade-offs between overall accrued system delay, the number of delayed flights, the total number of conflicts and the highest impedance observed as a function of the delay tolerance for each aircraft are provided. Potential applications to Urban Air Mobility traffic scenarios are also discussed.

ground-delay based traffic management↗
DOE OSTI2015

Standardized Procedure Content And Data Structure Based On Human Factors Requirements For Computer-Based Procedures

Most activities that involve human interaction with systems in a nuclear power plant are guided by procedures. Traditionally, the use of procedures has been a paper-based process that supports safe operation of the nuclear power industry. However, the nuclear industry is constantly trying to find ways to decrease the human error rate, especially the human errors associated with procedure use. Advances in digital technology make computer-based procedures (CBPs) a valid option that provides further enhancement of safety by improving human performance related to procedure use. The transition from paper-based procedures (PBPs) to CBPs creates a need for a computer-based procedure system (CBPS). A CBPS needs to have the ability to perform logical operations in order to adjust to the inputs received from either users or real time data from plant status databases. Without the ability for logical operations the procedure is just an electronic copy of the paper-based procedure. In order to provide the CBPS with the information it needs to display the procedure steps to the user, special care is needed in the format used to deliver all data and instructions to create the steps. The procedure should be broken down into basic elements and formatted in a standard method for the CBPS. One way to build the underlying data architecture is to use an Extensible Markup Language (XML) schema, which utilizes basic elements to build each step in the smart procedure. The attributes of each step will determine the type of functionality that the system will generate for that step. The CBPS will provide the context for the step to deliver referential information, request a decision, or accept input from the user. The XML schema needs to provide all data necessary for the system to accurately perform each step without the need for the procedure writer to reprogram the CBPS. The research team at the Idaho National Laboratory has developed a prototype CBPS for field workers as well as the underlying data structure for such CBPS. The objective of the research effort is to develop guidance on how to design both the user interface and the underlying schema. This paper will describe the result and insights gained from the research activities conducted to date.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2016

High-Performance Polymer Solar Cells Based on a Wide-Bandgap Polymer Containing Pyrrolo[3,4- f ]benzotriazole-5,7-dione with a Power Conversion Efficiency of 8.63%

A novel donor–acceptor type conjugated polymer based on a building block of 4,8-di(thien-2-yl)-6-octyl-2-octyl-5H-pyrrolo[3,4-f]benzotriazole-5,7(6H)-dione (TZBI) as the acceptor unit and 4,8-bis(5-(2-ethylhexyl)thiophen-2-yl)­benzo­[1,2-b:4,5-b']dithiophene as the donor unit, named as PTZBIBDT, is developed and used as an electron-donating material in bulk-heterojunction polymer solar cells. The resulting copolymer exhibits a wide bandgap of 1.81 eV along with relatively deep highest occupied molecular orbital energy level of -5.34 eV. Based on the optimized processing conditions, including thermal annealing, and the use of a water/alcohol cathode interlayer, the single-junction polymer solar cell based on PTZBIBDT:PC71BM ([6,6]-phenyl-C71-butyric acid methyl ester) blend film affords a power conversion efficiency of 8.63% with an open-circuit voltage of 0.87 V, a short circuit current of 13.50 mA cm -2 , and a fill factor of 73.95%, which is among the highest values reported for wide-bandgap polymers-based single-junction organic solar cells. The morphology studies on the PTZBIBDT:PC71BM blend film indicate that a fibrillar network can be formed and the extent of phase separation can be mani­pulated by thermal annealing. These results indicate that the TZBI unit is a very promising building block for the synthesis of wide-bandgap polymers for high-performance single-junction and tandem (or multijunction) organic solar cells.

Lan, Liuyuan↗
DOE OSTI2017

Stabilization of Li Metal Anode in DMSO‐Based Electrolytes via Optimization of Salt–Solvent Coordination for Li–O 2 Batteries

The conventional electrolyte of 1 m lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) in dimethyl sulfoxide (DMSO) is unstable against the Li metal anode and therefore cannot be used directly in practical Li–O 2 batteries. Here, we demonstrate that a highly concentrated electrolyte based on LiTFSI in DMSO (with a molar ratio of 1:3) can greatly improve the stability of the Li metal anode against DMSO and significantly improve the cycling stability of Li–O 2 batteries. This highly concentrated electrolyte contains no free DMSO solvent molecules, but only complexes of (TFSI − ) a Li + (DMSO) b (where a + b = 4), and thus enhances their stability with Li metal anodes. In addition, such salt–solvent complexes have higher Gibbs activation energy barriers than the free DMSO solvent molecules, indicating improved stability of the electrolyte against the attack of superoxide radical anions. Therefore, the stability of this highly concentrated electrolyte at both Li metal anodes and carbon‐based air electrodes has been greatly enhanced, resulting in improved cycling performance of Li–O 2 batteries. The fundamental stability of the electrolyte in the absence of free‐solvent against the chemical and electrochemical reactions can also be used to enhance the stability of other electrochemical systems.

Liu, Bin↗
DOE OSTI2016

The Role of MgCl 2 as a Lewis Base in ROMgCl–MgCl 2 Electrolytes for Magnesium‐Ion Batteries

Abstract A series of strong Lewis acid‐free alkoxide/siloxide‐based Mg electrolytes were deliberately developed with remarkable oxidative stability up to 3.5 V (vs. Mg/Mg 2+ ). Despite the perception of ROMgCl (R=alkyl, silyl) as a strong base, ROMgCl acts like Lewis acid, whereas the role of MgCl 2 in was unambiguously demonstrated as a Lewis base through the identification of the key intermediate using single crystal X‐ray crystallography. This Lewis‐acid‐free strategy should provide a prototype system for further investigation of Mg‐ion batteries.

Pan, Baofei↗
DOE OSTI2018

Interactions of Alumina-Based and Magnesia-Based Refractories with Iron Melts and Slags: A Review

A novel flash ironmaking technology (FIT) based on the direct reduction of iron ore concentrate with a reductant gas (such as hydrogen, natural gas, coal gas, or a combination thereof) in a flash furnace is being developed at the University of Utah. This technology which is undergoing large-scale laboratory testing aims at overcoming the limitations of blast furnace ironmaking by bypassing the problematic pelletization/sintering and cokemaking steps.[1–5] Refractory selection is expected to play an important step in the development of FIT and its proposed scale-up. For nominating an appropriate refractory for the FIT, understanding the interactions of candidate refractories with iron/iron oxide and slags under H{sub 2}/CO/CO{sub 2}/H{sub 2}O environments is necessary. This work is undertaken to review the existing literature on the interactions of important refractories with iron melts and relevant slags with an emphasis on two of the most commonly used refractories in ironmaking and steelmaking applications: the alumina-based refractories (used widely in blast furnace operations) and the magnesia-based refractories (used extensively in primary as well as secondary steelmaking). First, a comprehensive review on the interactions of alumina-based refractories with iron melts and slags has been done. Next the existing literature on the interactions of magnesia-based refractories with iron melts and relevant slags has been reviewed. Summaries have been included after each section and sub-section along with comments and critical insights from the authors. Finally, in the concluding remarks the differences in operating conditions between existing iron and steelmaking practices and the novel FIT have been highlighted. On the basis of these differences, it has been argued that the results and conclusions available from previous studies on refractory–metal–slag interactions are of little significance to flash ironmaking. Thus, there exists a need to carry out laboratory experiments for evaluating refractory performance in flash ironmaking under conditions relevant to the current process (FIT).

36 MATERIALS SCIENCE↗
DOE OSTI2014

Comparing cropland net primary production estimates from inventory, a satellite-based model, and a process-based model in the Midwest of the United States

Accurately quantifying the spatial and temporal variability of net primary production (NPP) for croplands is essential to understand regional cropland carbon dynamics. We compared three NPP estimates for croplands in the Midwestern United States: inventory-based estimates using crop yield data from the U.S. Department of Agriculture (USDA) National Agricultural Statistics Service (NASS); estimates from the satellite-based Moderate Resolution Imaging Spectroradiometer (MODIS) NPP product; and estimates from the General Ensemble biogeochemical Modeling System (GEMS) process-based model. The three methods estimated mean NPP in the range of 469–687 g C m -2 yr -1 and total NPP in the range of 318–490 Tg C yr -1 for croplands in the Midwest in 2007 and 2008. The NPP estimates from crop yield data and the GEMS model showed the mean NPP for croplands was over 650 g C m -2 yr -1 while the MODIS NPP product estimated the mean NPP was less than 500 g C m -2 yr -1 . MODIS NPP also showed very different spatial variability of the cropland NPP from the other two methods. We found these differences were mainly caused by the difference in the land cover data and the crop specific information used in the methods. Our study demonstrated that the detailed mapping of the temporal and spatial change of crop species is critical for estimating the spatial and temporal variability of cropland NPP. Finally, we suggest that high resolution land cover data with species–specific crop information should be used in satellite-based and process-based models to improve carbon estimates for croplands.

Biogeochemical model↗
DOE OSTI2015

Risk of Pathologic Upgrading or Locally Advanced Disease in Early Prostate Cancer Patients Based on Biopsy Gleason Score and PSA: A Population-Based Study of Modern Patients

Purpose: Radiation oncologists rely on available clinical information (biopsy Gleason score and prostate-specific antigen [PSA]) to determine the optimal treatment regimen for each prostate cancer patient. Existing published nomograms correlating clinical to pathologic extent of disease were based on patients treated in the 1980s and 1990s at select academic institutions. We used the Surveillance, Epidemiology, and End Results (SEER) database to examine pathologic outcomes (Gleason score and cancer stage) in early prostate cancer patients based on biopsy Gleason score and PSA concentration. Methods and Materials: This analysis included 25,858 patients whose cancer was diagnosed between 2010 and 2011, with biopsy Gleason scores of 6 to 7 and clinical stage T1 to T2 disease, who underwent radical prostatectomy. In subgroups based on biopsy Gleason score and PSA level, we report the proportion of patients with pathologically advanced disease (positive surgical margin or pT3-T4 disease) or whose Gleason score was upgraded. Logistic regression was used to examine factors associated with pathologic outcomes. Results: For patients with biopsy Gleason score 6 cancers, 84% of those with PSA <10 ng/mL had surgical T2 disease with negative margins; this decreased to 61% in patients with PSA of 20 to 29.9 ng/mL. Gleason score upgrading was seen in 43% (PSA: <10 ng/mL) to 61% (PSA: 20-29.9 ng/mL) of biopsy Gleason 6 patients. Patients with biopsy Gleason 7 cancers had a one-third (Gleason 3 + 4; PSA: <10 ng/mL) to two-thirds (Gleason 4 + 3; PSA: 20-29.9 ng/mL) probability of having pathologically advanced disease. Gleason score upgrading was seen in 11% to 19% of patients with biopsy Gleason 4 + 3 cancers. Multivariable analysis showed that higher PSA and older age were associated with Gleason score upgrading and pathologically advanced disease. Conclusions: This is the first population-based study to examine pathologic extent of disease and pathologic Gleason score upgrading based on clinically available information in modern patients. These data inform the selection of radiation therapy strategies and an understanding of whether prostatectomy alone is likely to be curative for patients with early prostate cancers.

62 RADIOLOGY AND NUCLEAR MEDICINE↗
DOE OSTI2018

Development of a lithium fluoride zinc sulfide based neutron multiplicity counter

Past 3He shortages led to investigations into replacement options for neutron detectors in systems that previously used 3He-based technologies. The goal of this research was to investigate the feasibility of a full-scale lithium fluoride with silver activated zinc sulfide (LiF/ZnS) based neutron multiplicity counter. The LiF/ZnS based neutron multiplicity counter (LiNMC) was developed based on an iterative process between modeling and experimental measurements. Each active region of the LiNMC contains five sheets of LiF/ZnS sandwiched between six sheets of wavelength shifting plastic to form neutron detection stacks. The wavelength shifted scintillation light was collected by photomultiplier tubes located on each end of the stacks. Twelve such detector stacks were placed around a sample chamber in a square arrangement with lithiated high density polyethylene blocks in the corners to reflect high energy neutrons and capture low energy neutrons. Preliminary calibration with a 252Cf neutron source showed that the LiNMC was able to achieve 36% neutron detection efficiency (ε) and an 11.7 μs neutron die-away time (τ) for a doubles Figure-of-merit (ε2/ τ) of 109. This is the highest doubles Figure-of-merit performance measured to-date for a 3He-free neutron multiplicity counter system. By the end of this project, the LiNMC’s basic components were integrated into a single laboratory scale system capable of proof-of-concept measurements.

3He-free↗
DOE OSTI2019

Non-targeted discovery-based analysis for gas chromatography with mass spectrometry: A comparison of peak table, tile, and pixel-based Fisher ratio analysis

The ability to discover minute differences between samples or sample classes for gas chromatography coupled to mass spectrometry (GC-MS) can be a challenging endeavor, especially when those differences are not a priori . Fisher ratio (F-ratio) analysis is an apt technique to probe the differences between GC-MS chromatograms. F-ratio analysis is a supervised, non-targeted, discovery-based method that compares two different samples (or sample classes) to reduce the GC-MS dataset into a hit list composed of class distinguishing compounds. Three different F-ratio techniques, peak table, tile, and pixel-based were used to “discover” nine non-native analytes that were spiked into gasoline at four different nominal concentrations of 250, 85, 25, 5 parts-per-million (ppm). For the tile and pixel-based F-ratio calculations, a novel methodology is introduced to improve the sensitivity of the F-ratio calculations while reducing false positives. Furthermore, we use a combinatorial technique using null class comparisons, termed null distribution analysis, to determine a statistical F-ratio cutoff for analysis of the hit lists. The pixel-based algorithm was the most sensitive method and was able to “discover” all nine spiked analytes at a nominal concentration of 250 ppm albeit with one false positive interspersed towards the bottom of the hit list. The pixel-based software was also able to “discover” more of the spiked analytes at the lower concentrations with seven of the spiked analytes “discovered” at 85 ppm, four of the spiked analytes “discovered” at 25 ppm, and one analyte “discovered” at 5 ppm.

47 OTHER INSTRUMENTATION↗
DOE OSTI2019

Poly(olefin)-Based Anion Exchange Membranes Prepared Using Ziegler–Natta Polymerization

Bromoalkyl-functionalized poly(olefin)s were synthesized by copolymerization of 4-(4-methylphenyl)-1-butene with 11-bromo-1-undecene using Ziegler–Natta polymerization. The resulting bromoalkyl-functionalized poly(olefin)s were converted to quaternary ammonium-containing anion-conductive copolymers by reacting the pendant bromoalkyl group with trimethylamine or a custom-synthesized tertiary amine containing pendant quaternary ammonium moieties. Poly(olefin)-based AEMs with three cations per side chain showed considerably higher hydroxide conductivities, up to 201 mS/cm at 80 °C in liquid water, compared to that of samples with only one cation per bromoalkyl site (68 mS/cm, 80 °C, liquid water), likely due to phase separation in the triple-cation structure. More importantly, triple-cation side-chain poly(olefin) AEMs exhibited higher hydroxide conductivity under relative humidity conditions (50%–100%) than typical AEMs based on benzyltrimethylammonium cations. Here, the triple-cation the triple-cation side-chain poly(olefin)-based AEM exhibited an ionic conductivity as high as 115 mS/cm under 95% RH at 80 °C and 11 mS/cm under 50% RH at 80 °C. In addition to high ionic conductivity, the triple-cation side-chain poly(olefin) AEMs exhibited good chemical and dimensional stability. High retention of ionic conductivity (>85%) was observed for the samples in 1 M NaOH at 80 °C over 1000 h. Based on these high-performance poly(olefin) AEMs, a fuel cell with a peak power density of 0.94 W cm –2 (1.28 W cm –2 after iR correction) was achieved under H 2 /O 2 at 70 °C. The results of this study suggest a new, low-cost, and scalable route for preparation of poly(olefin)-based AEMs for anion exchange membrane applications.

25 ENERGY STORAGE↗
DOE OSTI2021

Robust Solid/Electrolyte Interphase (SEI) formation on Si Anodes Using Glyme-based Electrolytes

Silicon (Si) is the most naturally abundant element possessing 10-fold theoretical capacity than graphitebased anodes. The practicality of implementing Si anodes is, however limited by the unstable solidelectrolyte interphase (SEI) and anode fracturing during continuous lithiation/delithiation. We demonstrate that glyme-based electrolytes (GlyEls) assure a conformal SEI on Si and keep the Si ‘fracture-free’. Benchmarking against the optimal, commonly-used carbonate electrolyte with the fluoroethylene carbonate (FEC) additive, Si anode cycled in a GlyEl exhibits reduced early parasitic current (by 62.5%) and interfacial resistance (by 72.8%), while the cell capacity retention is promoted by >7% over a course of 110 cycles. The mechanistic investigation by X-ray photoelectron spectroscopy (XPS) and energy-dispersive X-ray spectroscopy (EDX) indicates GlyEl enriches Si SEI with elastic polyether but diminishes its carbonate species. Glyme-based electrolytes prove viable in stabilizing the SEI on silicon for future high energy density lithium-ion batteries.

Yang, Guang↗