Search NASA⌕ Search

SEARCH · Search NASA

Results for “C”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Development of a continuous linear model of a d-c to d-c flyback converter.

The analytical design of the feedback circuit for a d-c flyback converter requires the formulation of a model defining the static and dynamic performance of the forward loop. This paper describes the steps which were taken to develop a linear continuous model of a typical flyback circuit. Although the method uses several approximations to simplify the work, the resulting model was found to duplicate the performance of the actual circuit very closely. The model makes it possible to design the feedback circuit using well known linear feedback techniques. The method is an extension of prior work in the modeling of pulse-width controlled circuits.

Wells, B. A.↗
NASA NTRS1973

GEOS-C coherent C-band transponder test procedure for spacecraft level tests

Procedures for the performance of two tests (electrical and airlink) for the transponder are outlined. The C-band test console used in performing the above tests is described (circuit diagrams and block diagrams), and equipment specifications are given. Calibration of the test equipment is also discussed.

Selser, A. R.↗
NASA NTRS1977

Interactive LORAN-C to geographic and geographic-to-LORAN-C computation

The LORAN program is stored in CMS disk files for use by Avionics Engineering Center terminal users. A CMS EXEC file named LORAN controls program operation. The user types LORAN and the program then prompts for data input and produces output on the terminal. The FORTRAN program refers to a disk file of LORAN master data giving station locations, coding delays, repetition rate and station pair identification letters. For Geographic-to-LORAN conversion, no iterative computations are required; the program is a straightforward coordinate conversion based upon the techniques described by the Navy. For LORAN-to-Geographic conversion, the original Navy program required a dead-reckoned position, near the actual unknown fix, to begin computations. No iteration was performed to obtain the LORAN fix, but internal program errors occurred at execution time if the dead-reckoned fix were displaced from the actual fix by more than a few minutes of latitude or longitude. In order to enhance usefulness of the program for the terminal user, an iterative routine was added which allows a single dead-reckoned position to be entered from the master data file for each LORAN chain. The results compare exactly with the LORAN-C navigation chart, and provide adequate benchmark data for general aviation flight planning and data analysis.

Piecuch, L. M.↗
NASA NTRS1980

Comparison of the weight loss and adherence of nine different polyimide films thermally aged at 315 C and 350 C in air

Thermal exposure experiments at 315 and 350 C were performed in air on nine different types of polyimides applied to thin 304 stainless steel foils. The tests were conducted to determine which polyimide was the most thermally stable and adherent when subjected to long exposure times at elevated temperatures. One polyimide designated PIC-7 was found to be more thermally stable than the others; however, it did not possess the adherent properties of PIC-2 and PIC-5. It was concluded that as far as thermal stability and adherence are concerned, five of the polyimides are more suitable for high temperature applications than the other four.

Fusaro, R. L.↗
NASA NTRS1984

Breakway friction and dynamic friction/wear measurements of various ceramic materials from 25 C (75 F) to 650 C (1200 F)

This report describes the results of a program designed to evaluate the breakaway friction and dynamic friction/wear characteristics of materials having potential for use as load bearing components in a high-performance high-temperature heavy duty diesel engine. Ten candidate materials were selected, six of which were evaluated under all possible material combinations as both stationary as well as moving breakaway specimens. The remaining materials were evaluated either in the static mode against themselves and all other materials, or against themselves only. Experiments were performed at five temperatures up to 650 C (1200 F) and unit pressures of 700 kPa (100 lb/sq in.), 3500 kPa (500 lb/sq in.), and 7000 kPa (1000 lb/sq in.). Experimental results indicate that under dynamic conditions, four of the ten materials exhibited good to excellent friction/wear characteristics in various material combinations. These materials were: titanium carbide, silicon nitride, silicon carbide (reaction sintered), and Refel (SiC).

Boes, D. J.↗
NASA NTRS1985

Implications of new measurements of O-16 + p + C-12,13, N-14,15 for the abundances of C, N isotopes at the cosmic ray source

The fragmentation of a 225 MeV/n O-16 beam was investigated at the Bevalac. Preliminary cross sections for mass = 13, 14, 15 fragments are used to constrain the nuclear excitation functions employed in galactic propagation calculations. Comparison to cosmic ray isotonic data at low energies shows that in the cosmic ray source C-13/C approximately 2% and N-14/0=3-6%. No source abundance of N-15 is required with the current experimental results.

Guzik, T. G.↗
NASA NTRS1992

A study of enhancing critical current densities (J(sub c)) and critical temperature (T(sub c)) of high-temperature superconductors

The development of pure phase 123 and Bi-based 2223 superconductors has been optimized. The pre-heat processing appears to be a very important parameter in achieving optimal physical properties. The synthesis of pure phases in the Bi-based system involves effects due to oxygen partial pressure, time, and temperature. Orientation/melt-sintering effects include the extreme c-axis orientation of Yttrium 123 and Bismuth 2223, 2212, and 2201 phases. This orientation is conductive to increasing critical currents. A procedure was established to substitute Sr for Ba in Y-123 single crystals.

Vlasse, Marcus↗
NASA NTRS2001

The Effect of O2, H2O, and N2 on the Fatigue Crack Growth Behavior of an Alpha + Beta Titanium Alloy at 24 C and 177 C

To study the effects of atmospheric species on the fatigue crack growth behavior of an a+B titanium alloy (Ti 6-2-2-2-2) at room temperature and 177 C, fatigue tests were performed in laboratory air, ultrahigh vacuum, and high purity water vapor, oxygen, nitrogen and helium at various partial pressures. Accelerated fatigue crack growth rates in laboratory air compared to ultrahigh vacuum are linked to the damaging effects of both water vapor and oxygen. Observations of the fatigue crack growth behavior in ultrahigh purity environments, along with surface film analysis using X-ray photoelectron spectroscopy (XPS), suggest that multiple crack-tip processes govern the damaging effects of air. Three possible mechanisms are proposed: 1) at low pressure (less than 10(exp -1) Pa), accelerated da/dN is likely due to monolayer adsorption on crack-tip surfaces presumably resulting in decreased bond strengths at the fatigue crack tip, 2) for pressures greater than 10(exp -1) Pa, accelerated da/dN in oxygen may result from oxidation at the crack tip limiting reversible slip, and 3) in water vapor, absorption of atomic hydrogen at the reactive crack tip resulting in process zone embrittlement.

Smith, Stephen W.↗
DOE OSTI2024

Hydrocarboxylation of C=C Bonds in Polycyclooctene: Progress Toward Valorization of Waste Polyolefins

Upcycling of waste polyolefins into higher-value functional polymers through chemical functionalization is a promising strategy to recover value and minimize their environmental impact. We report the hydrocarboxylation of polycyclooctene as a model for accessing ethylene acrylic acid copolymers (EAA) from waste polyethylene. The effects of various process parameters on the hydrocarboxylation were investigated. The relationship between carboxylic acid concentration and material properties, including crystallinity, melting temperature, glass transition temperature, adhesive properties, and wettability, was studied in comparison to an unfunctionalized polyethylene. Among the catalysts evaluated, Co 2 (CO) 8 exhibited relatively slow kinetics toward the hydrocarboxylation and was not compatible with 2,6-di-tert-butyl hydroxytoluene, a common additive present in commercial polyolefins. PdCl 2 (PPh 3 ) 2 exhibited a higher reactivity toward the hydrocarboxylation, though polymer gelation was observed with extended reaction times or high catalyst loadings. Carboxylic acid incorporation into the polymer was readily controlled by varying the reaction time. Altogether, the resultant COOH-functionalized polyolefins possessed properties analogous to commercial EAA.

36 MATERIALS SCIENCE↗