Search NASA⌕ Search

SEARCH · Search NASA

Results for “COLD CATHODE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

R&D ERL: Cryogenic System

The ERL cryogenic system will supply cooling to a super-conducting RF (SCRF) gun and the 5-cell super-conducting RF cavity system that need to be held cold at 2K. The engineering of the cavity cryomodules were carried out by AES in collaboration with BNL. The 2K superfluid bath is produced by pumping on the bath using a sub-atmospheric warm compression system. The cryogenic system makes use of mainly existing equipment relocated from other facilities: a 300W 4.5K coldbox, an 45 g/s screw compressor, a 3800 liter liquid helium storage dewar, a 170 m{sup 3} warm gas storage tank, and a 40,000 liter vertical low pressure liquid nitrogen storage dewar. An existing wet expander obtained from another facility has been added to increase the plant capacity. In order to deliver the required 3 to 4 bar helium to the cryomodules while using up stored liquid capacity at low pressure, a new subcooler will be installed to function as the capacity transfer device. A 2K to 4K recovery heat exchanger is also implemented for each cryomodule to recover refrigeration below 4K, thus maximizing 2K cooling capacity with the given sub-atmospheric pump. No 4K-300K refrigeration recovery is implemented at this time of the returning sub-atmospheric cold vapor, hence the 2K load appears as a liquefaction1 load on the cryogenic plant. A separate LN2 cooling loop supplies liquid nitrogen to the superconducting gun's cathode tip.

43 PARTICLE ACCELERATORS↗

Iodine Satellite

The Iodine Satellite (iSat) spacecraft will be the first CubeSat to demonstrate high change in velocity from a primary propulsion system by using Hall thruster technology and iodine as a propellant. The mission will demonstrate CubeSat maneuverability, including plane change, altitude change and change in its closest approach to Earth to ensure atmospheric reentry in less than 90 days. The mission is planned for launch in fall 2017. Hall thruster technology is a type of electric propulsion. Electric propulsion uses electricity, typically from solar panels, to accelerate the propellant. Electric propulsion can accelerate propellant to 10 times higher velocities than traditional chemical propulsion systems, which significantly increases fuel efficiency. To enable the success of the propulsion subsystem, iSat will also demonstrate power management and thermal control capabilities well beyond the current state-of-the-art for spacecraft of its size. This technology is a viable primary propulsion system that can be used on small satellites ranging from about 22 pounds (10 kilograms) to more than 1,000 pounds (450 kilograms). iSat's fuel efficiency is ten times greater and its propulsion per volume is 100 times greater than current cold-gas systems and three times better than the same system operating on xenon. iSat's iodine propulsion system consists of a 200 watt (W) Hall thruster, a cathode, a tank to store solid iodine, a power processing unit (PPU) and the feed system to supply the iodine. This propulsion system is based on a 200 W Hall thruster developed by Busek Co. Inc., which was previously flown using xenon as the propellant. Several improvements have been made to the original system to include a compact PPU, targeting greater than 80 percent reduction in mass and volume of conventional PPU designs. The cathode technology is planned to enable heaterless cathode conditioning, significantly increasing total system efficiency. The feed system has been designed to include iodine compatible control valves with internal heaters and temperature sensors to coincide with the iodine-compatible thruster. A key advantage to using iodine as a propellant is that it may be stored in the tank as an unpressurized solid on the ground and before flight operations. During operations, the tank is heated to vaporize the propellant. Iodine vapor is then routed through custom flow control valves to control mass flow to the thruster and cathode assembly. The thruster then ionizes the vapor and accelerates it via magnetic and electrostatic fields, resulting in high specific impulse, characteristic of a highly efficient propulsion system. The iSat spacecraft is a 12-unit (12U) CubeSat with dimensions of about 8 inches x 8 inches x 12 inches (20 centimeters x 20 centimeters x 30 centimeters). The spacecraft frame will be constructed from aluminum with a finish to prevent iodine-driven corrosion. The iSat spacecraft includes full three-axis control and will leverage heat generated by spacecraft components and radiators for a passive thermal control system. After the CubeSat has successfully detached from its launch vehicle, it will deploy its solar panels, correct for tip-off and maintain attitude control before ground contact. An initial check-out period of two weeks is planned for testing all subsystems. The spacecraft will charge the power system while in sunlight, using momentum wheels and magnetic torque rods to rotate the vehicle to the required attitude.

iSat↗

Next Generation Batteries for Electric Aviation and Space

Energy storage plays a critical part in the success of future NASA missions that desire batteries with higher energy density, higher power, and most critically improved safety. These performance requirements stretch beyond that of electric automobile markets and are required for enabling widespread adoption of electric aviation. One approach to improve the safety and energy is the transition to non-volatile solid-state electrolytes (SSE) which promise many advantages over traditional flammable liquid electrolytes and may also be an enabling technology for next generation chemistries such as lithium-sulfur (Li-S). However, significant manufacturing challenges must be overcome before the adoption of such technology. This study will discuss the development of solid electrolytes specifically designed to meet future NASA electric aviation targets with densified thicknesses between 20-30 microns derived using solvent processing techniques. Films were produced 10-15 times thinner than comparable bulk cold pressed powder electrolytes and achieved thicknesses comparable to commercial polyolefin separators (25 micron) used in commercial liquid containing lithium-ion cells. Furthermore, design and development of novel cathode composites through integration of experiment and a particle dynamics model will be discussed. Beyond aeronautics, unique challenges and requirements exist for energy storage for space applications, which can cover extreme temperatures and material scarcity for in-situ derived materials. Additionally, this talk will briefly cover the need and development of lunar and Martian derived electrode materials for in-situ manufacturing of energy storage devices.

Batteries↗

IMPROVED DETERMINATION OF THE 1{sub 0}-0{sub 0} ROTATIONAL FREQUENCY OF NH{sub 3}D{sup +} FROM THE HIGH-RESOLUTION SPECTRUM OF THE {nu}{sub 4} INFRARED BAND

The high-resolution spectrum of the {nu}{sub 4} band of NH{sub 3}D{sup +} has been measured by difference frequency IR laser spectroscopy in a multipass hollow cathode discharge cell. From the set of molecular constants obtained from the analysis of the spectrum, a value of 262817 {+-} 6 MHz ({+-}3{sigma}) has been derived for the frequency of the 1{sub 0}-0{sub 0} rotational transition. This value supports the assignment to NH{sub 3}D{sup +} of lines at 262816.7 MHz recorded in radio astronomy observations in Orion-IRc2 and the cold prestellar core B1-bS.

74 ATOMIC AND MOLECULAR PHYSICS↗

Analytic model of the energy distribution function for highly energetic electrons in magnetron plasmas

This paper analyzes a situation which is common for magnetized technical plasmas such as dc magnetron discharges and high power impulse magnetron sputtering (HiPIMS) systems, where secondary electrons enter the plasma after being accelerated in the cathode fall and encounter a nearly uniform bulk. An analytic calculation of the distribution function of hot electrons is presented; these are described as an initially monoenergetic beam that slows down by Coulomb collisions with a Maxwellian distribution of bulk (cold) electrons, and by inelastic collisions with neutrals. Although this analytical solution is based on a steady-state assumption, a comparison of the characteristic time-scales suggests that it may be applicable to a variety of practical time-dependent discharges, and it may be used to introduce kinetic effects into models based on the hypothesis of Maxwellian electrons. The results are verified for parameters appropriate to HiPIMS discharges, by means of time-dependent and fully kinetic numerical calculations.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Axial mass fraction measurements in a 300kA dense plasma focus

The dynamics and characteristics of the plasma sheath during the axial phase in a ~300 kA, ~2 kJ dense plasma focus using a static gas load of Ne at 1–4 Torr are reported. The sheath, which is driven axially at a constant velocity ~10 5 m/s by the j × B force, is observed using optical imaging, to form an acute angle between the electrodes. This angle becomes more acute (more parallel to the axis) along the rundown. The average sheath thickness nearer the anode is 0.69 ± 0.02 mm and nearer the cathode is 0.95 ± 0.02 mm. The sheath total mass increases from 1 ± 0.02 μg to 6 ± 0.02 μg over the pressure range of 1–4 Torr. However, the mass fraction (defined as the sheath mass/total mass of cold gas between the electrodes) decreases from 7% to 5%. In addition, the steeper the plasma sheath, the more mass is lost from the sheath, which is consistent with radial and axial motion. Lastly, experimental results are compared to the Lee code when 100% of the current drives the axial and radial phase.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Axial plasma jet characterization on a microsecond x-pinch

The jets produced on a microsecond x-pinch (quarter period T 1/4 ~ 1 μs, dI/dt ~ 0.35 kA/ns) have been studied through light-field schlieren imaging and optical framing photographs across 4 different materials: Al, Ti, Mo, and W. The axial velocity of the jets was measured and exhibited no dependence on atomic number (Z) of the wire material. Additionally, there may be a dependence on another factor(s), namely, the current rise rate. The average axial jet velocity across all four materials was measured to be 2.9 ± 0.5 × 10 6 cm/s. The average jet diameter and the average radial jet expansion rate displayed inverse relationships with Z, which may be attributed to radiative cooling and inertia. Asymmetry between the anode and cathode jet behavior was observed and is thought to be caused by electron beam activity. The mean divergence angle of the jet was found to vary with wire material and correlated inversely with the thermal conductivity of the cold wire. Optical images indicated a two-layer structure in Al jets which may be caused by standing shocks and resemble phenomena observed in astrophysical jet formation and collimation. Finally, kinks in the jets have also been observed which may be caused by m = 1 MHD instability modes or by the interaction of the jet with the electrode plasma.

36 MATERIALS SCIENCE↗

Environmental Testing of the NEXT PM1 Ion Engine

The NEXT propulsion system is an advanced ion propulsion system presently under development that is oriented towards robotic exploration of the solar system using solar electric power. The Prototype Model engine PM1 was subjected to qualification-level environmental testing to demonstrate compatibility with environments representative of anticipated mission requirements. Random vibration testing, conducted with the thruster mated to the breadboard gimbal, was executed at 10.0 Grms for 2 minutes in each of three axes. Thermal-vacuum testing included a deep cold soak of the engine to temperatures of -168 C and thermal cycling from -120 to 203 C. Although the testing was largely successful, several issues were identified including the fragmentation of potting cement on the discharge and neutralizer cathode heater terminations during vibration which led to abbreviated thermal testing, and generation of particulate contamination from manufacturing processes and engine materials. Thruster performance was nominal throughout the test program, with minor variations in some engine operating parameters likely caused by facility effects. In general, the NEXT PM1 engine and the breadboard gimbal were found to be well-designed against environmental requirements based on the results reported herein. After resolution of the findings from this test program the hardware environmental qualification program can proceed with confidence.

Synder, John S.↗

Investigation of the short argon arc with hot anode. I. Numerical simulations of non-equilibrium effects in the near-electrode regions

The atmospheric pressure arcs have recently found application in the production of nanoparticles. The distinguishing features of such arcs are small length and hot ablating anode characterized by intensive electron emission and radiation from its surface. We performed a one-dimensional modeling of argon arc, which shows that near-electrode effects of thermal and ionization non-equilibrium play an important role in the operation of a short arc, because the non-equilibrium regions are up to several millimeters long and are comparable to the arc length. The near-anode region is typically longer than the near-cathode region and its length depends more strongly on the current density. The model was extensively verified and validated against previous simulation results and experimental data. The Volt-Ampere characteristic (VAC) of the near-anode region depends on the anode cooling mechanism. The anode voltage is negative. In the case of strong anode cooling (water-cooled anode) when the anode is cold, temperature and plasma density gradients increase with current density, resulting in a decrease of the anode voltage (the absolute value increases). Falling VAC of the near-anode region suggests the arc constriction near the anode. Without anode cooling, the anode temperature increases significantly with the current density, leading to a drastic increase in the thermionic emission current from the anode. Correspondingly, the anode voltage increases to suppress the emission, and the opposite trend in the VAC is observed. Here, the results of simulations were found to be independent of sheath model used: collisional (fluid) or collisionless model gave the same plasma profiles for both near-anode and near-cathode regions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

R&D ERL: Vacuum

The ERL Vacuum systems are depicted in a figure. ERL has eight vacuum volumes with various sets of requirements. A summary of vacuum related requirements is provided in a table. Five of the eight volumes comprise the electron beamline. They are the 5-cell Superconducting RF Cavity, Superconducting e-gun, injection, loop and beam dump. Two vacuum regions are the individual cryostats insulating the 5-cell Superconducting RF Cavity and the Superconducting e-gun structures. The last ERL vacuum volume not shown in the schematic is the laser transport line. The beamline vacuum regions are separated by electropneumatic gate valves. The beam dump is common with loop beamline but is considered a separate volume due to geometry and requirements. Vacuum in the 5-cell SRF cavity is maintained in the {approx}10{sup -9} torr range at room temperature by two 20 l/s ion pumps and in the e-gun SRF cavity by one 60 l/s ion pump. Vacuum in the SRF cavities operated at 2{sup o}K is reduced to low 10{sup -11} torr via cryopumping of the cavity walls. The cathode of the e-gun must be protected from poisoning, which can occur if vacuum adjacent to the e-gun in the injection line exceeds 10-11 torr range in the injection warm beamline near the e-gun exit. The vacuum requirements for beam operation in the loop and beam dump are 10-9 torr range. The beamlines are evacuated from atmospheric pressure to high vacuum level with a particulate free, oil free turbomolecular pumping cart. 25 l/s shielded ion pumps distributed throughout the beamlines maintain the vacuum requirement. Due to the more demanding vacuum requirement of the injection beamline proximate to the e-gun, a vacuum bakeout of the injection beamline is required. In addition, two 200 l/s diode ion pumps and supplemental pumping provided by titanium sublimation pumps are installed in the injection line just beyond the exit of the e-gun. Due to expected gas load a similar pumping arrangement is planned for the beam dump. The cryostat vacuum thermally insulating the SRF cavities need only reduce the convective heat load such that heat loss is primarily radiation through several layers of multi-layer insulation and conductive end-losses which are contained by 5{sup o}K thermal transitions. Prior to cool down rough vacuum {approx}10{sup -5} torr range is established and maintained by a dedicated turbomolecular pump station. Cryopumping by the cold mass and heat shields reduces the insulating vacuum to 10{sup -7} torr range after cool down.

43 PARTICLE ACCELERATORS↗

Freeze Tape Cast Thick Mo Doped Li 4 Ti 5 O 12 Electrodes for Lithium-Ion Batteries

Lithium titanate (Li 4 Ti 5 O 12 ) powders with and without molybdenum doping (LTO and MoLTO respectively) were synthesized by a solid-state method and used to fabricate electrodes on Cu foil using a normal tape-cast method and a novel freeze-tape-cast method. Modest molybdenum doping produces a significant electronic conductivity increase (e.g. 1 mS cm -1 for MoLTO vs 10 -7 mS cm -1 for LTO) that is thought to reflect a partial Ti 4+ reduction to Ti 3+ with charge compensation by the Mo 6+ dopant, producing a stable mixed-valent Ti 4+/3+ state. Freeze-tape-cast electrodes were fabricated by a variant of the normal tape-cast method that includes a rapid freezing step in which the solvent in the Cu-foil-supported slurry is rapidly frozen on a cold finger then subsequently sublimed to create unidirectional columnar macropores in the electrode. The resulting electrodes exhibit high porosity and low tortuosity which enhances electrolyte accessibility throughout the full electrode thickness. Freeze-tape-cast electrodes subjected to galvanostatic charge-discharge testing as cathodes in cells vs. a lithium metal anode exhibit higher specific capacity and lower capacity loss at high discharge rates compared with normal-tape-cast electrodes of the same mass loading, despite the fact that the freeze-tape-cast electrodes are nearly twice as thick as the normal tape cast electrodes.

25 ENERGY STORAGE↗

High-Performance Electron Sources: Numerical Methods and Beam Dynamics at the Precision Frontier

Electron sources have a wide range of applications and there are many stakeholders that express continuing need for improvements and performance enhancements. Whether we consider ultra-cold, high-brightness, high-charge or high-average current source needs, there are some common themes from the point of view of the beam dynamics involved. These are the following ones: ability to model accurately the emission processes, including the presence of often complicated cathode and other boundary surfaces with a wide range of spatial scales; ability to deal accurately and efficiently with a large number of particles interacting pair-wise, including the stochastic part of these interactions with a wide range of spatial scales; and ability to propagate the particle distributions in time, including collisions with a wide range of temporal scales. These tasks require high precision and accuracy since the goal is usually generation, transport and preservation of very high-quality beams. This grant addressed one of the rem

43 PARTICLE ACCELERATORS↗

EMPIRE-PIC Code Verification of a Cold Diode

This report presents the code verification of EMPIRE-PIC to the analytic solution to a cold diode which was first derived by Jaffe. The cold diode was simulated using EMPIRE-PIC and the error norms were computed based on the Jaffe solution. The diode geometry is one-dimensional and uses the EMPIRE electrostatic field solver. After a transient start-up phase as the electrons first cross the anode-cathode gap, the simulations reach an equilibrium where the electric potential and electric field are approximately steady. The expected spatial order of convergence for potential, electric field and particle velocity are observed.

42 ENGINEERING↗

On Io, all that flickers is not cold

The 4.8 micron flux from the Galilean satellite Io was shown to fluctuate with an amplitude of approximately 10 percent on time scales of every 28 seconds, 40 minutes, night-to-night, and perhaps year-to-year. Such behavior was found to be the result of random fluctuations for which the mean square fluctuation varies inversely with frequency for constant bandwidth measurement. The theory developed for thermionic emission from barium oxide cathodes in vacuum tubes might be applicable to this situation. If so, the fluctuations in the flux from Io's volcanoes may be caused by diffusion of hot convective cells onto the surface of Io. Long term fluctuations may furnish a means by which the Io volcanism can shut down and conserve energy. Thus the discrepancy that exists between measurements of the current heat flow from Io and calculations of tidal dissipation may be resolved. Tests for rapid flickering at 10 microns showed no fluctuations greater than one percent. This agrees with the prediction of the flow model theory in which the 10 microns volcanic thermal emission arises from cooling of old flows.

Sinton, W. M.↗

Antifouling Properties and Release of Dissolved Copper of Cold Spray Cu/Cu{sub 2}O Coatings for Ships and Steel Structures in Marine Environment

At the submarine screen doors of ships, the flow of water was fast and organic coatings were easy to peel off. To solve the problems of biofouling, the Cu/Cu{sub 2}O coatings were prepared by cold spray technology. In this paper, the release mechanism of effective antifouling components of the coatings was studied by micro-domain electrochemical potential scanning technique. Cuprous oxide in the coatings and the surrounding copper constituted micro-cells which accelerated the local electrochemical dissolution of copper. Cuprous oxide acted as the cathode, and the surrounding copper acted as the anode. Meanwhile, under the action of current, chloride ions were transferred from cathode to the anode and promoted local electrochemical dissolution of copper. Experiments show that the higher the Cu{sub 2}O content in the coatings, the greater the release rate of dissolved copper and inhibitory effect on diatoms. In the environments varied in dissolved oxygen, salinity, temperature and flow rate, the coatings maintained sufficient release rate of dissolved copper, unless the salinity was very low. Most of the dissolved copper was provided by the electrochemical dissolution process of copper. Whether in the indoor test or marine environment experiments, 30% Cu{sub 2}O coatings show the best performance. After insulating layer was sprayed, the effect of antifouling was improved evidently and the coatings were applied to the submarine screen doors of ships.

36 MATERIALS SCIENCE↗

Low-current traveling wave tube for use in the microwave power module

The results of a traveling-wave-tube/multistage depressed-collector (TWT-MDC) design study in support of the Advanced Research Projects Agency/Department of Defense (ARPA/DOD) Microwave Power Module (MPM) Program are described. The study stressed the possible application of dynamic and other tapers to the RF output circuit of the MPM traveling wave tube as a means of increasing the RF and overall efficiencies and reducing the required beam current (perveance). The results indicate that a highly efficient, modified dynamic velocity taper (DVT) circuit can be designed for the broadband MPM application. The combination of reduced cathode current (lower perveance) and increased RF efficiency leads to (1) a substantially higher overall efficiency and reduction in the prime power to the MPM, and (2) substantially reduced levels of MDC and MPM heat dissipation, which simplify the cooling problems. However, the selected TWT circuit parameters need to be validated by cold test measurements on actual circuits.

Palmer, Raymond W.↗

Sensitivity analysis for characterizing the impact of HNGD model on the prediction of hydrogen redistribution in Zircaloy cladding using BISON code

Hydrogen in zirconium cladding is able to precipitate into zirconium hydrides which impacts cladding integrity. The Hydride Nucleation-Growth-Dissolution (HNGD) model in the BISON code accounts for the precipitation and dissolution kinetics of hydride in Zircaloy material. This paper presents global sensitivity analyses of the HNGD model aiming to enhance our understanding of the hydride precipitation phenomena by quantifying the variance that key parameters have on the prediction of hydrogen behavior under various environmental conditions. Here, model predictions are compared to experimental data obtained under two different conditions: 1) with uniformly precharged specimens subjected to a linear thermal gradient, and 2) specimens precharged with a cathodically applied hydride rim at one end of the sample and subjected to an asymmetric thermal gradient. The Sobol sensitivity analysis identifies the key parameters in the HNGD model for both types of specimens. For linear temperature cases, the heat of transport dominates the accuracy of predictions when no precipitation occurs at the cold end, while Terminal Solid Solubility for Dissolution (TSSD) is the most important parameter when precipitation occurs. A large variation in the predicted hydrogen concentration profiles is found in the range of high TSSD due to the occurrence of precipitation. For asymmetric temperature cases, the solubility coefficient gives the largest impact on the predicted hydrogen distribution, as it determines the amount of solute hydrogen dissolved from the initially applied hydride rim. A large discrepancy in hydrogen distribution between simulations and experiments exists with the asymmetric specimens because BISON simulations fail to predict the precipitation of hydride at the cooler end. Comparative studies using former and updated models verifies the significant impact of the hydride growth mechanism on predicted hydrogen concentration profiles. In particular, when hydride initially exists, changes in TSSD generate a large variation in the predicted amount of precipitation by hydride growth, giving large uncertainty in predicting the hydrogen distribution over the sample length. The outputs characterize the significant impact of the hydride growth mechanism in the HNGD model on predicting hydrogen behavior, and improve the understanding of the precipitation of hydride in Zircaloy cladding within a range of expected environmental conditions. The analyses indicate work is still needed to improve the hydride solvus models in the BISON code to accurately predict experimentally observed hydride concentrations and distributions.

36 MATERIALS SCIENCE↗

NASA Tech Briefs, March 2010

Topics covered include: Software Tool Integrating Data Flow Diagrams and Petri Nets; Adaptive Nulling for Interferometric Detection of Planets; Reducing the Volume of NASA Earth-Science Data; Reception of Multiple Telemetry Signals via One Dish Antenna; Space-Qualified Traveling-Wave Tube; Smart Power Supply for Battery-Powered Systems; Parallel Processing of Broad-Band PPM Signals; Inexpensive Implementation of Many Strain Gauges; Constant-Differential-Pressure Two-Fluid Accumulator; Inflatable Tubular Structures Rigidized with Foams; Power Generator with Thermo-Differential Modules; Mechanical Extraction of Power From Ocean Currents and Tides; Nitrous Oxide/Paraffin Hybrid Rocket Engines; Optimized Li-Ion Electrolytes Containing Fluorinated Ester Co-Solvents; Probabilistic Multi-Factor Interaction Model for Complex Material Behavior; Foldable Instrumented Bits for Ultrasonic/Sonic Penetrators; Compact Rare Earth Emitter Hollow Cathode; High-Precision Shape Control of In-Space Deployable Large Membrane/Thin-Shell Reflectors; Rapid Active Sampling Package; Miniature Lightweight Ion Pump; Cryogenic Transport of High-Pressure-System Recharge Gas; Water-Vapor Raman Lidar System Reaches Higher Altitude; Compact Ku-Band T/R Module for High-Resolution Radar Imaging of Cold Land Processes; Wide-Field-of-View, High-Resolution, Stereoscopic Imager; Electrical Capacitance Volume Tomography with High-Contrast Dielectrics; Wavefront Control and Image Restoration with Less Computing; Polarization Imaging Apparatus; Stereoscopic Machine-Vision System Using Projected Circles; Metal Vapor Arcing Risk Assessment Tool; Performance Bounds on Two Concatenated, Interleaved Codes; Parameterizing Coefficients of a POD-Based Dynamical System; Confidence-Based Feature Acquisition; Algorithm for Lossless Compression of Calibrated Hyperspectral Imagery; Universal Decoder for PPM of any Order; Algorithm for Stabilizing a POD-Based Dynamical System; Mission Reliability Estimation for Repairable Robot Teams; Processing AIRS Scientific Data Through Level 3; Web-Based Requesting and Scheduling Use of Facilities; AutoGen Version 5.0; Time-Tag Generation Script; PPM Receiver Implemented in Software; Tropospheric Emission Spectrometer Product File Readers; Reporting Differences Between Spacecraft Sequence Files; Coordinating "Execute" Data for ISS and Space Shuttle; Database for Safety-Oriented Tracking of Chemicals; Apparatus for Cold, Pressurized Biogeochemical Experiments; Growing B Lymphocytes in a Three-Dimensional Culture System; Tissue-like 3D Assemblies of Human Broncho-Epithelial Cells; Isolation of Resistance-Bearing Microorganisms; Oscillating Cell Culture Bioreactor; and Liquid Cooling/Warming Garment.

Source record↗