Search NASA⌕ Search

SEARCH · Search NASA

Results for “CONICAL NOZZLE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1999

Design of a Low Speed Fan Stage for Noise Suppression

This report describes the design of a low tip speed, moderate pressure rise fan stage for demonstration of noise reduction concepts. The fan rotor is a fixed-pitch configuration delivering a design pressure ratio of 1.378 at a specific flow of 43.1 lbm/sec/sq ft. Four exit stator configurations were provided to demonstrate the effectiveness of circumferential and axial sweep in reducing rotor-stator interaction tone noise. The fan stage design was combined with an axisymmetric inlet, conical convergent nozzle, and nacelle to form a powered fan-nacelle subscale model. This model has a 22-inch cylindrical flow path and employs a rotor with a 0.30 hub-to-tip radius ratio. The design is fully compatible with an existing NASA force balance and rig drive system. The stage aerodynamic and structural design is described in detail. Three-dimensional (3-D) computational fluid dynamics (CFD) tools were used to define optimum airfoil sections for both the rotor and stators. A fan noise predictive system developed by Pratt & Whitney under contract to NASA was used to determine the acoustic characteristics of the various stator configurations. Parameters varied included rotor-to-stator spacing and vane leading edge sweep. The structural analysis of the rotor and stator are described herein. An integral blade and disk configuration was selected for the rotor. Analysis confirmed adequate low cycle fatigue life, vibratory endurance strength, and aeroelastic suitability. A unique load carrying stator arrangement was selected to minimize generation of tonal noise due to sources other than rotor-stator interaction. Analysis of all static structural components demonstrated adequate strength, fatigue life, and vibratory characteristics.

Dalton, W. N.↗
NASA NTRS1986

Performance of high area ratio nozzles for a small rocket thruster

Theoretical estimates of supersonic nozzle performance have been compared to experimental test data for nozzles with an area ratio of 100:1 conical and 300:1 optimum contour, and 300:1 nozzles cut off at 200:1 and 100:1. These tests were done on a Hughes Aircraft Company 5 lbf monopropellant hydrazine thruster with chamber pressures ranging from 25 to 135 psia. The analytic method used is the conventional inviscid method of characteristic with correction for laminar boundary layer displacement and drag. Replacing the 100:1 conical nozzle with the 300:1 contoured nozzle resulted in an improvement in thrust performance of 0.74 percent at chamber pressure of 25 psia to 2.14 percent at chamber pressure of 135 psia. The data is significant because it is experimental verification that conventional nozzle design techniques are applicable even where the boundary layer is laminar and displaces as much as 35 percent of the flow at the nozzle exit plane.

Kushida, R. O.↗
NASA NTRS1980

Effects of nozzle design on the noise from supersonic jets

The aeroacoustic supersonic performance of various internal nozzle geometries is evaluated for shock noise content over a wide range of nozzle pressure ratios. The noise emission of a Mach 1.5 and 2.0 convergent-divergent (C-D) nozzle is measured and compared to convergent nozzles. Comparisons are also made for a Mach 1.5 conical C-D nozzle and a porous plug nozzle. The Mach 1.5 conical C-D nozzle shows a small reduction in shock noise relative to the shock free case of the Mach 1.5 C-D nozzle. The Mach 1.5 C-D nozzle is found to have a wide operating nozzle pressure ratio range around its design point where shock noise remains unimportant compared to the jet mixing noise component. However it is found that the Mach 2 C-D nozzle shows no significant acoustic benefit relative to the convergent nozzle. Results from the porous plug nozzle indicate that shock noise may be completely eliminated, and the jet mixing noise reduced.

Seiner, J. M.↗
NASA NTRS1972

Flight velocity influence on jet noise of conical ejector, annular plug and segmented suppressor nozzles

An F106 aircraft with a J85-13 engine was used for static and flight acoustic and aerodynamic tests of a conical ejector, an unsuppressed annular plug, and three segmented suppressor nozzles. Static 100 ft. arc data, corrected for influences other than jet noise, were extrapolated to a 300 ft. sideline for comparison to 300 ft. altitude flyover data at M = 0.4. Data at engine speeds of 80 to 100% (max dry) static and 88 to 100% flight are presented. Flight velocity influence on noise is shown on peak OASPL and PNL, PNL directivity, EPNL and chosen spectra. Peak OASPL and PNL plus EPNL suppression levels are included showing slightly lower flight than static peak PNL suppression but greater EPNL than peak PNL suppression. Aerodynamic performance was as anticipated and closely matched model work for the 32-spoke nozzle.

Brausch, J. F.↗
NASA NTRS1983

Aeroacoustics of supersonic porous plug-nozzle flows

The effects of porosity on attenuation of noise from short plug-nozzle flows have been studied. Porosity of 10 percent distributed over the whole surface and porosity of 4 percent distributed over the middle-third surface of the conical plug have been investigated. The porosity results in favorable modifications of the repetitive shock structures as revealed by the shadowgraphs of the flow. The acoustic data indicate a reduction of noise intensity levels up to 4 dB for the porous plugs as compared to the solid concial plug. The locally distributed holes (4 percent porosity) are found to give aeroacoustic performance comparable to those with holes distributed over the whole surface (10 percent porosity). Also, the solid conical plug-nozzle is noted to yield noise reductions up to 9 dB when compared to the conical convergent plug-nozzle. A proposed mechanism of shock modification in porous plug-nozzle. A supported by shadowgraphic records.

Dosanjh, D. S.↗
NASA NTRS1972

Jet effects on the drag of conical afterbodies at supersonic speeds

A parametric investigation has been conducted to determine the jet effects on the boattail drag of nozzles with truncated conical afterbodies. The boattail drag for nozzle configurations with boattail angles of 3 deg, 5 deg, and 10 deg and ratios of boattail length to maximum diameter of 1.0, 0.8, and 0.6 was compared for the jet-off condition and for a wide range of jet pressure ratios. A nozzle configuration with a circular-arc boattail was tested also. The tests were run at Mach numbers of 1.83 and 2.20 with the model at an angle of attack of 0 deg.

Compton, W. B., III↗
NASA NTRS1960

Performance of Several Conical Convergent-Divergent Rocket-Type Exhaust Nozzles

An investigation was conducted to obtain nozzle performance data with relatively large-scale models at pressure ratios as high as 120. Conical convergent-divergent nozzles with divergence angles alpha of 15, 25, and 29 deg. were each tested at area ratios of approximately 10, 25, and 40. Heated air (1200 F) was supplied at the nozzle inlet at pressures up to 145 pounds per square inch absolute and was exhausted into quiescent air at pressures as low as 1.2 pounds per square inch absolute. Thrust ratios for all nozzle configurations are presented over the range of pressure ratios attainable and were extrapolated when possible to design pressure ratio and beyond. Design thrust ratios decreased with increasing nozzle divergence angle according to the trend predicted by the (1 + cos alpha)/2 parameter. Decreasing the nozzle divergence angle resulted in sizable increases in thrust ratio for a given surface-area ratio (nozzle weight), particularly at low nozzle pressure ratios. Correlations of the nozzle static pressure at separation and of the average static pressure downstream of separation with various nozzle parameters permitted the calculation of thrust in the separated-flow region from unseparated static-pressure distributions. Thrust ratios calculated by this method agreed with measured values within about 1 percent.

Campbell, C. E.↗
NASA NTRS1974

Effect of configuration variation on externally blown flap noise

The sensitivity of flap interaction noise to variations in engine-under-the-wing externally blown flap geometry was investigated with a large cold-flow model. Both 2- and 3-flap wing sections (7-ft chord) with trailing flap angles up to 60 deg were employed. Exhaust nozzles included coaxial, plug, and 8- and 13-inch diameter conical configurations. These nozzles were tested at two positions below the wing. The effects of these geometry variations on noise level, directivity, and spectral shape are summarized in terms of exhaust flow parameters evaluated at the nozzle exit and at the flap impingement station. The results are also compared with limited flap noise data available from tests using real engines.

Dorsch, R. G.↗
NASA NTRS1974

Effect of configuration variation on externally blown flap noise

The sensitivity of flap interaction noise to variations in engine-under-the-wing externally blown flap geometry was investigated with a large cold-flow model. Both two- and three-flap wing sections (7-ft chord) with trailing flap angles up to 60 deg were employed. Exhaust nozzles included coaxial, plug, and 8- and 13-in.-diam conical configurations. These nozzles were tested at two positions below the wing (19-1/4 and 29-1/4 in.). The effects of these geometry variations on noise level, directivity, and spectral shape are summarized in terms of exhaust flow parameters evaluated at the nozzle exit and at the flap impingement station. The results are also compared with limited flap noise data available from tests using real engines.

Dorsch, R. G.↗
NASA NTRS1975

Installation and airspeed effects on jet shock-associated noise

Experimental acoustic data are presented to illustrate, at model scale, the effect of varying the nozzle-wing installation on shock-associated noise, statically and with airspeed. The variation in installations included nozzle only, nozzle under-the-wing (with and without flaps deflected), and nozzle over-the-wing (unattached flow). The nozzles used were a conical and a 6-tube mixer nozzle with a cold-flow nozzle pressure ratio of 2.1. A 33-cm diameter free jet was used to simulate airspeed. With the nozzle only, shock wave noise dominated the spectra in the forward quadrant, while jet mixing noise dominated in the rearward quadrant. Similar trends were observed when a wing (flaps retracted) was included. Shock noise was attenuated with an over-the-wing configuration and increased with an under-the-wing configuration (due to reflection from the wing surface). With increasing flap deflection (under-the-wing configuration), the jet-flap interaction noise exceeded the shock noise and became dominant in both quadrants. The free jet results showed that airspeed had no effect on shock noise. The free jet noise data were corrected for convective amplification to approximate flight and comparisons between the various configurations are made.

Vonglahn, U.↗
NASA NTRS1981

Aeroacoustics of a porous plug jet noise suppressor

The aeroacoustics of a porous plug jet noise suppressor was investigated. The predicted flow features of isentropic plug nozzles for different pressure ratios or exit flow Mach numbers, throat areas, ratios of the plug to annular nozzle radii, mass flow rates and the available run times possible with the existing compressed air supply system, are compiled. The dimensions and the coordinates of the contour of typical isentropic external expansion plugs with different exit flow Mach numbers are listed. Design details of the experimental facility and the plug nozzle selected for experimental aeroacoustic studies are reported. The analytical flow prediction by method of characteristics of a conical porous plug nozzles is initiated. The role of the shape, size, and porosity of the plug surface in achieving over a perforated conical plug a nearly isentropic shockfree supersonic flow field which is closely similar to the flow field of a contoured isentropic plug nozzle is examined.

Dosanjh, D. S.↗
NASA NTRS1990

Arcjet Nozzle Area Ratio Effects

An experimental investigation was conducted to determine the effect of nozzle area ratio on the operating characteristics and performance of a low power dc arcjet thruster. Conical thoriated tungsten nozzle inserts were tested in a modular laboratory arcjet thruster run on hydrogen/nitrogen mixtures simulating the decomposition products of hydrazine. The converging and diverging sides of the inserts had half angles of 30 and 20 degrees, respectively, similar to a flight type unit currently under development. The length of the diverging side was varied to change the area ratio. The nozzle inserts were run over a wide range of specific power. Current, voltage, mass flow rate, and thrust were monitored to provide accurate comparisons between tests. While small differences in performance were observed between the two nozzle inserts, it was determined that for each nozzle insert, arcjet performance improved with increasing nozzle area ratio to the highest area ratio tested and that the losses become very pronounced for area ratios below 50. These trends are somewhat different than those obtained in previous experimental and analytical studies of low Re number nozzles. It appears that arcjet performance can be enhanced via area ratio optimization.

Curran, Francis M.↗
NASA NTRS1990

Arcjet nozzle area ratio effects

An experimental investigation was conducted to determine the effect of nozzle area ratio on the operating characteristics and performance of a low power dc arcjet thruster. Conical thoriated tungsten nozzle inserts were tested in a modular laboratory arcjet thruster run on hydrogen/nitrogen mixtures simulating the decomposition products of hydrazine. The converging and diverging sides of the inserts had half angles of 30 and 20 degrees, respectively, similar to a flight type unit currently under development. The length of the diverging side was varied to change the area ratio. The nozzle inserts were run over a wide range of specific power. Current, voltage, mass flow rate, and thrust were monitored to provide accurate comparisons between tests. While small differences in performance were observed between the two nozzle inserts, it was determined that for each nozzle insert, arcjet performance improved with increasing nozzle area ratio to the highest area ratio tested and that the losses become very pronounced for area ratios below 50. These trends are somewhat different than those obtained in previous experimental and analytical studies of low Re number nozzles. It appears that arcjet performance can be enhanced via area ratio optimization.

Curran, Francis M.↗
NASA NTRS1975

Forward velocity effects on under-the-wing externally blown flap noise

Noise tests were conducted with small-scale models of externally blown-flap powered-lift systems that were subjected to simulated takeoff and landing free-stream velocities by placing the nozzle-wing models in a free jet. The nozzle configurations consisted of a conical and an 8-tube mixer nozzle. The results show that the free-stream velocity attenuates the noise from the various configurations, with the amount of attenuation depending on the flap setting. More attenuation was obtained with a flap setting of 20 degrees than with a flap setting of 60 degrees. The dynamic effect on the total attenuation caused by aircraft motion is also discussed.

Goodykoontz, J.↗
NASA NTRS1975

Forward velocity effects on under-the-wing externally blown flap noise

Noise tests were conducted with small-scale models of externally blown-flap powered-lift systems that were subjected to simulated takeoff and landing free-stream velocities by placing the nozzle-wing models in a free jet. The nozzle configurations consisted of a conical and an 8-tube mixer nozzle. The results showed that the free-stream velocity attenuated the noise from the various configurations with the amount of attenuation depending on the flap setting. More attenuation was obtained with a flap setting of 20 deg than with a flap setting of 60 deg. The dynamic effect on the total attenuation caused by aircraft motion is also discussed.

Goodykoontz, J.↗
NASA NTRS2004

Corrugated and Composite Nozzle-Inlets for Thrust and Noise Benefits

The following research results are based on development of an approach previously proposed and investigated in for optimum nozzle design to obtain maximum thrust. The design was denoted a Telescope nozzle. A Telescope nozzle contains one or several internal designs, which are inserted at certain locations into a divergent conical or planar main nozzle near its exit. Such a design provides additional thrust augmentation over 20% by comparison with the optimum single nozzle of equivalent lateral area, What is more, experimental acoustic tests have discovered an essential noise reduction due to application of Telescope nozzles. In this paper, some additional theoretical results are presented for Telescope nozzles and a similar approach is applied for aero-performance improvement of a supersonic inlet. Numerical simulations were conducted for supersonic flow into the divergent portion of a 2D or axisymmetric nozzle with several plane or conical designs as well as into a 2D or axisymmetric supersonic inlet with a forebody. The Kryko-Godunov marching numerical scheme for inviscid supersonic flows was used. Several cases were tested using the NASA CFL3d and IM/MSU Russian codes based on the full Navier-Stokes equations. Numerical simulations were conducted for non reacting flows (both codes) as well as for real high temperature gas flows with non-equilibrium chemical reactions (the latter code). In general, these simulations have confirmed essential benefits of Telescope design applications in propulsion system. Some preliminary numerical simulations of several typical inlet designs were conducted with the goal of inlet design optimization for maneuvering flight conditions.

Gilinsky, M.↗
NASA NTRS1980

Model aerodynamic test results for two variable cycle engine coannular exhaust systems at simulated takeoff and cruise conditions

Wind tunnel tests were conducted to evaluate the aerodynamic performance of a coannular exhaust nozzle for a proposed variable stream control supersonic propulsion system. Tests were conducted with two simulated configurations differing primarily in the fan duct flowpaths: a short flap mechanism for fan stream control with an isentropic contoured flow splitter, and an iris fan nozzle with a conical flow splitter. Both designs feature a translating primary plug and an auxiliary inlet ejector. Tests were conducted at takeoff and simulated cruise conditions. Data were acquired at Mach numbers of 0, 0.36, 0.9, and 2.0 for a wide range of nozzle operating conditions. At simulated supersonic cruise, both configurations demonstrated good performance, comparable to levels assumed in earlier advanced supersonic propulsion studies. However, at subsonic cruise, both configurations exhibited performance that was 6 to 7.5 percent less than the study assumptions. At take off conditions, the iris configuration performance approached the assumed levels, while the short flap design was 4 to 6 percent less.

Nelson, D. P.↗