Search NASA⌕ Search

SEARCH · Search NASA

Results for “CONJUNCTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Assessing the impacts of air-sealing on the sizing, operation, and economic feasibility of ground-source heat pumps for electrifying single-family houses in the US

According to recent studies and reports, in single-family houses (SFHs), air-sealing can significantly lower the thermal loads for space heating and cooling. Thus, air-sealing in SFHs could reduce the required size and cost of ground source heat pump (GSHP) systems for electrifying SFHs. Here, this study investigated the costs and benefits of integrating air-sealing with GSHPs for retrofitting existing SFHs when compared with air-source heat pumps. A whole building energy simulation tool integrated with an advanced design tool for modeling ground heat exchangers was used to calculate changes in required GSHP capacity, total borehole length, and building energy consumption with and without air-sealing in SFHs in 16 US climatic regions. The results from this study showed that reducing outdoor air infiltration from 0.8 air changes per hour (ACH) to the minimum ventilation requirement (0.35 ACH) can significantly reduce borehole length (up to 55 %), GSHP capacity (up to 48 %), and total heating electricity reduction, especially in cold climates (up to 44 %). The results also showed that for airtight homes (0.03 ACH infiltration) with a direct outdoor air system, the minimum required borehole length, GSHP capacity, and total heating electricity consumption can be reduced up to 70 %, 68 %, and 67 %, respectively, when compared with SFHs with 0.8 ACH infiltration. Moreover, the life cycle cost analysis showed that air-sealing in conjunction with a GSHP is more profitable than replacing the existing system with an air-source heat pump, even without any incentives for most climatic regions in the US (except for some hot regions).

15 GEOTHERMAL ENERGY↗
DOE OSTI2020

Multi-GPU immersed boundary method hemodynamics simulations

Large-scale simulations of blood flow that resolve the 3D deformation of each comprising cell are increasingly popular owing to algorithmic developments in conjunction with advances in compute capability. Among different approaches for modeling cell-resolved hemodynamics, fluid structure interaction (FSI) algorithms based on the immersed boundary method are frequently employed for coupling separate solvers for the background fluid and the cells within one framework. GPUs can accelerate these simulations; however, both current pre-exascale and future exascale CPU-GPU heterogeneous systems face communication challenges critical to performance and scalability. In this paper, we describe, to our knowledge, the largest distributed GPU-accelerated FSI simulations of high hematocrit cell-resolved flows with over 17 million red blood cells. We compare scaling on a fat node system with six GPUs per node and on a system with a single GPU per node. Through comparison between the CPU- and GPU-based implementations, we identify the costs of data movement in multiscale multi-grid FSI simulations on heterogeneous systems and show it to be the greatest performance bottleneck on the GPU.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2022

Laser ablation for structuring Li-ion electrodes for fast charging and its impact on material properties, rate capability, Li plating, and wetting

Laser ablation is a scalable technique for decreasing the effective tortuosity of electrodes by selectively removing material with high precision. Applied to ≈ 110 um thick electrode coatings, this work focuses on understanding the impact of laser ablation on electrode material properties at the beginning of life and synergistic impacts of ablated channels on cell performance throughout their cycle life. Post laser ablation, local changes in chemistry, crystallography, and morphology of the laser-impacted electrode regions are investigated. It is shown that femtosecond pulsed laser ablation can achieve high-rate material removal with minor material damage locally at the interface of the impacted zones. The capacity achieved during a 6C (10 min) constant-current constant-voltage charge to 4.2 V improved from 1 mAh cm -2 for the non-ablated electrodes to almost 2 mAh cm -2 for the ablated electrodes. This benefit is attributed to a synergistic effect of enhanced wetting and decreased electrode tortuosity. The benefit was maintained for over 120 cycles, and upon disassembly decreased Li-plating on the graphite anode was observed. Finally, multi-physics modeling in conjunction with wetting analyses showed that laser ablating either one of the electrodes led to substantial improvements in wetting and rate capability, indicating that substantial performance benefits can be achieved by ablating only the graphite anode as apposed to both electrodes.

25 ENERGY STORAGE↗
DOE OSTI2022

Proper orthogonal decomposition based reduced-order modeling of flux-Limited gray thermal radiation

Here, in this work, a proper orthogonal decomposition (POD) based reduced-order model (ROM) is developed to solve gray, flux-limited thermal radiation diffusion. We focus on the variable opacity radiation penetration benchmark posed by Olson, Auer, and Hall. The T -3 relationship for opacity in conjunction with high-temperature radiation penetrating an initially cold material produces a strong thermal radiation shock. This class of problems is particularly challenging for standard POD-based reduced-order modeling due to the nonlinearities presented by 1) the T 4 source term, and 2) flux-limited diffusion operator. To address these challenges and develop a cost competitive ROM, we employ a “hyper-reduction” technique through discrete empirical interpolation (DEIM) and allow for adaptive reduced-order projections through principal interval decomposition (PID). Performance of the proposed methodology is quantified by comparing the cost savings and accuracy relative to a full-order computation. Reference solutions and snapshot data are obtained through a full-order calculation performed by the University of Chicago maintained astrophysics code, FLASH. For consistency and potential extensibility, the developed ROM is also implemented in FLASH. We find that in the initialization regime, where the thermal radiation wave is initially created by the warming of the material, this class of problems is highly reducible and suitable for POD-based ROMs. However, the strong convective nature of the wave propagation regime is less reducible and more challenging to create an efficient ROM.

42 ENGINEERING↗
DOE OSTI2025

Low-lying states and total internal partition sums of CH

The electronic structure and spin-orbit states of the CH radical have been systematically investigated using multi-reference configuration interaction (MRCI) and single-reference coupled-cluster (CC) methods. These calculations were performed in conjunction with large correlation-consistent basis sets of quadruple-, quintuple-, and sextuple-ζ quality. To achieve high accuracy, electronic energies for all states were extrapolated to the complete basis set (CBS) limit, enabling the detailed construction of potential energy curves and determination of reliable spectroscopic constants. Spin-orbit coupling effects were explicitly incorporated, and vibrational energy levels were computed via Numerov analysis. Furthermore, the resulting values exhibit good to excellent agreement with available experimental data. Dipole moment and transition dipole moment curves were evaluated to assess the opacity characteristics of CH, revealing that transitions such as Χ 2 Π (u′′ = 0) → Α 2 Δ (u′ = 0), Χ 2 Π (u′′ = 0) → Β 2 Σ − (u′ = 0), Χ 2 Π (u′′ = 0) → C 2 Σ + (u′ = 0), and Χ 2 Π (u′′ = 0) → D 2 Σ + (u′ = 3) are particularly probable. Finally, the total internal partition function sum (TIPS) of CH was computed over a broad temperature range (10–30,000 K) based on our high-accuracy ab initio results.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2021

A numerical and experimental approach to compare the effect of sample thickness in small in-situ SEM and large ex-situ tensile testing in Alloy 709

ASTM standards for tensile tests define specific sample size requirements regardless of grain size of the material. However, sample size requirements for testing should be considered in conjunction with the number of grains within its reduced cross-sectional area. This is particularly important for in-situ Scanning Electron Microscope (SEM) tensile tests, as they have to be conducted on smaller samples. In this study, a comprehensive experimental and numerical evaluation of the effect of specimen thickness (and the resulting number of grains within the cross-section) were conducted using in-situ SEM tensile test (on submillimeter thick samples) and ex-situ tensile tests (on samples of 0.68–5.9 mm thickness) and the results are compared with FEM simulations outcome. All tests were conducted at room temperature and the results are correlated to the number of grains within the thickness of specimens. The tensile test results indicated that even though the 0.2% proof stress and the tensile strength do not vary for the current range of thicknesses (with number of grains in the cross-section varying from 13 to 118), a difference in necking mechanism exists. Post tensile strength, thinner samples undergo more shear failure and diagonal localized necking whereas thicker samples experience more diffuse necking indicated by decreased area of shear failure at the edges and increased area of dimpled tensile failure at the center of the sample. Further, FEM results complement the experimental findings by showing the formation of conjugated localized shear bands on the upper and lower surface in the 0.68 mm thick sample and shear bands combining to form singular shear bands in thicker samples. These results also confirm the validity of the in-situ SEM tensile tests conducted on thinner samples as long as the required minimum number of grains exist within the cross-section.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Exceptional strength and wear resistance in an AA7075/TiB 2 composite fabricated via friction consolidation

The friction consolidation method successfully reinforced aluminum 7075 alloy (AA7075) with high-volume fractions (12 and 24 vol%) of titanium diboride (TiB 2 ) by high pressure and severe plastic deformation at elevated temperatures. The consolidated AMCs have a uniform dispersion of submicron- and micron-sized TiB 2 particles in the AA7075 matrix, with significant refinement of the matrix grain size and the particles. The addition of TiB 2 significantly increases hardness by up to 50 %, Young’s modulus by up to 62 %, and ultimate tensile strength by up to 28 % to 672 MPa, while reducing ductility by 80 %. Wear resistance of 7075/24 vol% TiB 2 improves seven-fold compared to baseline, making it comparable to that of carburized steels. Microstructure-based finite element modeling provided a theoretical strength limit of ~730 MPa for the composites and indicated that high triaxiality in conjunction with severe equivalent plastic strain in a narrow area between the TiB 2 particles led to early fracture initiations, limiting the ductility.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Acoustic velocities, elasticity, and pressure-induced elastic softening in compressed neodymium

For the first time, the acoustic velocities and elasticity of double hexagonal close-packed neodymium (Nd) were measured at high pressure using ultrasonic interferometry in conjunction with synchrotron X-ray techniques. Here, both the compressional and shear wave velocities increased with an increase in pressure of up to ~5.4 GPa before they exhibited almost constant values upon further compression. This pressure-induced elastic wave velocity softening can be attributed to the structural instability in dhcp-Nd. From the current sound velocities and density data, we obtained new bulk and shear moduli as well as their pressure dependence for polycrystalline dhcp-Nd, yielding $B_0$=33.2(9) GPa, $G_0$=14.1(5) GPa, $\partial$$B/$$\partial$$P$ = 3.6 (4) and $\partial$$=G/$$\partial$$P$ = 1.3 (2) while other elasticity-related/mechanical properties, including Young's modulus, Debye temperature, Poisson's ratio, and Grüneisen parameter, which are important parameters for the application of Nd in extreme environments, were also derived.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Experimental observation of nonlinear relation between pressure and water flux is consistent with the solution-diffusion model

In several recent studies, it has been proposed that the fundamental understanding of penetrant transport in dense polymer membranes occurring via the solution-diffusion model, which has been the generally accepted theoretical framework for describing penetrant transport in such materials for the past several decades, is flawed. An alternate mechanistic framework based on the idea of two-phase flow in a porous medium (i.e., pore-flow) has been broadly advanced instead, with proponents of this approach claiming that the pore-flow theoretical framework provides the necessary mechanistic insight to design novel polymeric membrane materials for emerging applications. In this study, we show experimental results for hydraulic permeation of water that are entirely consistent with the solution-diffusion theory, without modification, for three dense polymeric membranes: crosslinked poly(ethylene glycol diacrylate) (XLPEGDA), Nafion 117 ionomer in the sodium counterion form (Nafion 117-Na), and cellulose acetate (CA). By measuring water flux at transmembrane pressures up to 240 bar, we observe a nonlinear relationship between the transmembrane pressure (TMP) and water flux, J w , for XLPEGDA and Nafion 117-Na, while this relationship is linear for CA. We demonstrate that the behavior of these three materials is described via the solution-diffusion model. According to the solution-diffusion model, flux is, to a good approximation, proportional to the transmembrane concentration difference induced by the pressure difference across the membrane, rather than to TMP itself. Water sorption isotherms are reported for all three materials. They further justify the nonlinear relationship between TMP and J w observed in XLPEGDA and Nafion 117-Na, emphasizing that the nonlinearity in the flux/TMP relationship stems from nonlinearities in the sorption isotherm with pressure. Additionally, the relationship between water flux and TMP can be predicted, a priori, with no adjustable parameters when a predictive model for the diffusion coefficient of water is employed in conjunction with the experimental water sorption isotherms in the solution-diffusion model. Furthermore, our results demonstrate the validity of the solution-diffusion model to describe transport of penetrants in dense polymer membranes, while highlighting the sensitivity of the solution-diffusion model to the many physical and mathematical simplifications commonly applied to the theory in literature.

materials↗
DOE OSTI2023

Data-driven acoustic measurement of moisture content in flowing biomass

Measuring the moisture content in flowing biomass is critical to processes such as liquid biofuel conversion, such as biogasoline, biodiesel, bio jet kerosene, etc. However, biomass tends to flow in aggregates, which results in significant inhomogeneities in the amount of biomass flowing in front of a sensor at a given time, and there can be significant overlap in the material properties of dry vs wet biomass, leading to poor signal-to-noise ratio. We present a technique for identifying biomass moisture content using a series of acoustic pitch-catch measurements to quantify the sound speed and acoustic amplitude through the biomass, in conjunction with classical machine learning techniques, including Naive Bayes, Random Forest, and K-Nearest Neighbors classification. We amplify the differences between the acoustic measurements in different moisture levels by collecting a series of pulse-echo measurements, which we sort in order of ascending sound speed. We test the accuracy of the technique on experimentally-prepared batches of corn stover biomass with specified moisture levels and measure the average error in the estimated moisture level as a function of the number of pitch-catch measurements used. We observe average estimation errors as low as 6.7% by increasing the number of measurements and optimizing the hyperparameters. This work presents a novel method determining moisture content in flowing biomass with inhomogeneous flow. Additionally, this technique has application in optimizing biomass conversion processes, as well as other fields including, paper production, natural fiber processing, and mineral extraction.

09 BIOMASS FUELS↗
DOE OSTI2025

Facile synthesis of co-doped Carbon nanofibers for supercapacitor applications

Here, in this study, the synthesis and electrochemical performance of carbon nanofibers (CNFs) co-doped with aluminum (Al) and nitrogen (N) and decorated with zinc oxide (ZnO) nanoparticles are investigated. After electrospinning polyacrylonitrile (PAN) nanofibers, the nanofiber mats are coated with Al and ZnO precursors by the dip coating method and converted into carbon nanofibers by thermal treatments at 850 °C. Co-doping and nanoparticle decoration affect the efficacy of carbon nanofibers as supercapacitors. With a maximal specific capacitance of 206.28 Fg -1 , it is believed that our produced carbon nanofibers, which can effectively store the renewable energy resources required to meet the rising energy demand, offer superior electrochemical properties compared to traditional supercapacitor materials. The effective incorporation of Al, N, and ZnO into the CNF structure, in conjunction with enhanced electrochemical performance, represents a significant advancement in the development of functional carbon nanofibers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Effect of heterogeneous microstructure on the tensile and creep performances of cast Haynes 282 alloy

Precipitation-strengthened Ni-based superalloys are leading candidate materials for advanced ultra-supercritical (A-USC) plants with steam conditions up to 760 °C (1400 °F) and 35 MPa (5 ksi). This study evaluates representative specimens from a large casting of Haynes 282 to study the effect of microstructural heterogeneity on the mechanical behavior of this alloy. The tensile test results of cast Haynes 282 over the temperature range 20–816 °C exhibited lower tensile strength and ductility in comparison with the reference wrought Haynes 282. However, the creep rupture tests of the cast alloy below 704–788 °C and 190–431 MPa presented a similar stress-Larson-Miller parameter to that of the wrought material. Microstructural and dislocation characterizations using scanning electron microscopy, conventional transmission electron microscopy, and scanning transmission electron microscopy in conjunction with energy dispersive X-ray spectroscopy were performed to understand the microstructural evolution before and after the mechanical tests. The heterogeneous microstructures of the cast Haynes 282 material, including the coarse grains, potential casting defects, and a bimodal size distribution of γ' precipitates, were detrimental to the tensile behavior, whereas the coarse-scale grains had a positive effect on the creep performance because diffusional creep was the dominant creep mechanism.

tensile testing↗
DOE OSTI2021

Precipitation behavior near shrinkage porosity in a large sand casting of Haynes 282 alloy

The precipitation behavior of L1 2 structure Ni 3 (Al,Ti)-type γ' precipitates near shrinkage porosity in a large sand casting of Haynes 282 alloy has been investigated by scanning/transmission electron microscopy in conjunction with energy dispersive x-ray spectroscopy. The experimental results revealed that in the carbonitride-rich region close to the shrinkage porosity, γ' precipitates could still form with comparable sizes though at lower volume density than those in the general cast Ni matrix. The resulting γ' precipitates had a very high Al/Ti ratio. Close to oxide-rich pore surfaces, an absence of γ' precipitates was observed due to Al and Ti depletion by forming Al oxides and Ti carbonitrides, respectively. This work suggests that Al rather than Ti plays a dominant role in the formation of γ' precipitates in porous regions in cast Haynes 282 alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Multicolored microwave absorbers with dynamic frequency modulation

Microwave-absorbing materials are extensively used in intelligent electronic devices and stealth technologies where the ability to dynamically adjust microwave-absorbing capacity in response to specific requirements is vitally important. Herein, we report a new approach for constructing dynamically tunable microwave absorbers with ultrawide tunable frequency ranges that are simultaneously endowed with vibrant structural colors. Here, the methodology produces structural colors and adjusts absorption properties by constructing ZnO coatings with precisely adjustable thicknesses on a polypyrrole/melamine foam (PPy/MF) surface by atomic layer deposition (ALD) in conjunction with a pressure-driven strategy that regulates the compression ratio. The electrical conductivity, electromagnetic parameters, thickness, and pore size of the ZnO-coated PPy/MF (ZnO/PPy/MF) are effectively adjusted, and simply applying external pressure widens the tunable frequency range and the effective absorption bandwidth. As a result, the effective absorption frequency of ZnO/PPy/MF is dynamically adjustable from the S band to the Ku band, thereby covering 94.3% of the entire microwave spectrum. Moreover, the brilliant and uniform structural colors of ZnO/PPy/MF, which span various color categories, are precisely regulated by tuning the thickness of the ZnO coating by adjusting the number of ALD cycles. ZnO/PPy/MF is strongly hydrophobic, which endows it with remarkable self-cleaning properties. Therefore, ZnO/PPy/MF provides a conceptually novel platform for the development of next-generation smart microwave-absorbing materials due to its integrated dynamic frequency-regulating ability, brilliant structural coloration, and self-cleaning features.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Intrinsically sodiophilic, mesoporous metal-free wetting layers based on inexpensive carbon black for sodium-metal batteries

In this article, elevated temperature molten Na batteries are seeing a resurgence of interest for low-cost electrochemical energy storage for the grid. Of the many recent innovations in this battery concept, new methods focused on intermediate temperature operation (e.g. 110–190 °C) have gained prominence as a way to enable comparable performance with less thermal energy loss and lower-cost materials of construction. However, the poor wettability of molten Na on suitable solid-electrolyte separators such as sodium Beta Alumina Solid-Electrolyte (Na-β”-Al 2 O 3 , ‘BASE’) requires continued innovation in interface engineering to promote full utilization of the solid-electrolyte surface area and minimize cell resistance. There have been many successful approaches to improve Na-wettability to-date including heat treatment in an inert atmosphere to remove adsorbed surface species, deposition of alloying metals such as Pb, Sn, or Bi, and use of carbon-based interfacial layers. However, these approaches either lack the ability to provide good wetting at very low temperatures (near the melting point of Na) or rely on non-scalable processes and/or toxic/expensive metals. To solve these issues, a new carbon-based sodiophilic treatment is demonstrated, which utilizes inexpensive components to form a meso/macroporous sodiophilic layer, is easily applied via drop-casting or spray-coating, provides excellent wetting as low as 110 °C, and is completely metal-free. It is found that the good sodium wetting can be attributed to the wider range of pore sizes in the carbon layers demonstrated in this study. Na wetting may occur as surface tension is initially broken by larger pores, followed by the intrusion of molten Na into smaller pores due to the apparent intrinsic affinity of Na-metal for carbon surfaces, in conjunction with the capillarity effect. Low cell-level area specific resistances of 20–30 and 13–15 Ω·cm 2 are demonstrated at 110 and 140 °C respectively. Finally, the utility of this metal-free wetting layer for solid-Na anodes is explored, showing that the metal-free wetting layer can reach a critical current density of 1.88 mA·cm -2 at 30 °C.

25 ENERGY STORAGE↗
DOE OSTI2020

Beta-delayed charged-particle spectroscopy using TexAT

β-delayed charged-particle emission is a sensitive probe of three-body decays in light nuclei. Time Projection Chambers (TPCs) offer a significant advantage over traditional charged-particle spectroscopy techniques due to a low-energy threshold and a high-geometric efficiency (≈ 4π) which are essential for use with radioactive ion beams where the beam intensities are limited. The technique for high-sensitivity spectroscopy of β-delayed charged-particle emission is shown to be possible using the Texas Active Target (TexAT) TPC in conjunction with the General Electronics for TPCs (GET) system. The benchmark case studied was that of 12 N β-decay to the first α-unbound state in 12 C, the Hoyle state. Here, half-life and branching ratio measurements are presented and are in good agreement with previous studies. The efficacy of using TPCs to study such a near-threshold state and disentangle the three-body dynamics of the decay products is demonstrated.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2022

Scientific computing plan for the ECCE detector at the Electron Ion Collider

The Electron Ion Collider (EIC) is the next generation of precision QCD facility to be built at Brookhaven National Laboratory in conjunction with Thomas Jefferson National Laboratory. There are a significant number of software and computing challenges that need to be overcome at the EIC. During the EIC detector proposal development period, the ECCE consortium began identifying and addressing these challenges in the process of producing a complete detector proposal based upon detailed detector and physics simulations. Here, in this document, the software and computing efforts to produce this proposal are discussed; furthermore, the computing and software model and resources required for the future of ECCE are described.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗