Search NASA⌕ Search

SEARCH · Search NASA

Results for “CRACK FORMATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1940

The cause of welding cracks in aircraft steels

The discussion in this article refers to gas welding of thin-walled parts of up to about 3 mm thickness. It was proven that by restricting the sulphur, carbon, and phosphorous content, and by electric-furnace production of the steel, it was possible in a short time to remove this defect. Weld hardness - i.e., martensite formation and hardness of the overheated zone - has no connection with the tendency to weld-crack development. Si, Cr, Mo, or V content has no appreciable effect, while increased manganese content tends to reduce the crack susceptibility.

Muller, J↗
NASA NTRS1966

X-ray analysis of fatigue damage in copper

A Warren-Averbach x-ray line profile analysis was applied to, broadened x-ray diffraction peaks from copper deformed in fatigue. The copper specimens were fatigued by four point bending at various strain amplitudes, and measurements were made at various fractions of the total fatigue life. The analysis results in an estimation of 1) an average coherently diffracting domain size in a direction normal to the diffracting planes; and 2) a strain distribution function. The strain distribution function is in terms of the root mean square strain, <ϵ^(2)> where ϵ is averaged over a given distance at all points in the diffracting crystals. This rms strain is expressed as a function of averaging distance for a direction normal to the diffracting planes. The rms strains were found to be a function of the fatigue strain amplitude level, increasing with amplitude and reaching a maximum limiting value during the first 2% of the fatigue life. The strains were normally larger in the 4lO0 direction compared to the <111> direction and the absolute values were quite small. These results may be explained by assuming the dislocations are present in the form of dipoles because the lattice strain around a dipole is much less than around single dislocations. Conclusions arrived at in this analysis are in agreement with current theories of fatigue damage in metals. The result that maximum hardening is achieved during the initial few percent of the fatigue life is confirmed by many other investigators using entirely different analytical techniques. It is felt that the structure of the material is changing during this initial hardening stage to an eventual steady state characteristic of the testing conditions. A unique substructure is developed which thereafter persists, and the remainder of the fatigue test is taken up by crack propagation through this substructure until ultimate failure occurs by fracture. The formation of this steady state structure is dependent on the maximum fatigue strain amplitude and on the frequency and temperature of cycling for a particular material.

COPPER↗
NASA NTRS2020

Impact-driven mobilization of deep crustal brines on dwarf planet Ceres

Ceres, the only dwarf planet in the inner Solar System, appears to be a relict ocean world. Data collected by NASA's Dawn spacecraft provided evidence that global aqueous alteration within Ceres resulted in a chemically evolved body that remains volatile-rich(1). Recent emplacement of bright deposits sourced from brines attests to Ceres being a persistently geologically active world(2,3), but the surprising longevity of this activity at the 92-km Occator crater has yet to be explained. Here, we use new high-resolution Dawn gravity data to study the subsurface architecture of the region surrounding Occator crater, which hosts extensive young bright carbonate deposits (faculae). Gravity data and thermal modelling imply an extensive deep brine reservoir beneath Occator, which we argue could have been mobilized by the heating and deep fracturing associated with the Occator impact, leading to long-lived extrusion of brines and formation of the faculae. Moreover, we find that pre-existing tectonic cracks may provide pathways for deep brines to migrate within the crust, extending the regions affected by impacts and creating compositional heterogeneity. The long-lived hydrological system resulting from the impact might also occur for large impacts in icy moons, with implications for creation of transient habitable niches over time.High-resolution data of Ceres's bright spots (faculae), obtained by Dawn's second extended mission, suggest the existence of a deep brine-rich reservoir that emerged to the surface through long-lived cryovolcanic activity as a consequence of the impact that created Occator crater.

C. A. Raymond↗
NASA NTRS2000

The Relation Between Alloy Chemistry and Hot-Cracking

Hot cracking is a problem in welding 2195 aluminum-lithium alloy. Weld wire additives seem to reduce the problem. This study proposes a model intended to clarify the way alloying elements affect hot-cracking. The brittle temperature range of an alloy extends wherever the tensile stress required to move the meniscus of the liquid film at the grain/dendrite boundaries is less than the bulks flow stress Sigma(sub B) of the grains: 2gamma/delta <= sigma(sub B) + P where gamma is boundary film surface tension delta= boundary film thickness P = gas pressure (Some alloys outgas.) If the above condition is not met, the grains deform under stress and the liquid film remains in place. Curves of 2gamma/delta and sigma(sub B) vs. temperature in the range just below the melting temperature determine the hot cracking susceptibility of an alloy. Both are zero at onset of solidification. sigma(sub B) rises as the thermal activation of the slip mechanism is reduced. 2gamma/delta rises as the film thickness delta which can be estimated from the Scheil equation, drops. But, given an embrittled alloy, whether the alloy actually cracks is determined by the strain imposed upon it in the embrittled condition. A critical strain is estimated, Epsilon(sub C) on the order of Epsilon(sub C) is approximately delta/l where L = grain size and where the the volume increment due to the strain, concentrated at the liquid film, is on the order of the liquid film volume. In the early 80's an empirical critical strain cracking envelope Epsilon(sub C)(T) was incorporated into a damage criterion to estimate the effect of welding parameters on the formation of microfissures in a superalloy with good results. These concepts, liquid film decoherence vs. grain bulk deformation and critical strain, form the key elements of a quantitative theory of hot-cracking applicable for assessing the effect of alloying elements on hot-cracking during welding.

Nunes, A. C., Jr.↗
NASA NTRS1979

XPS and SAM studies of the surface chemistry of lunar impact glasses including 12054

We report and discuss quantitative X-ray photoemission (XPS) analyses of mm size areas and qualitative scanning Auger microprobe (SAM) analyses of micron size areas on the surfaces of impact glass coatings found on fragments in the 14161 coarse fines and on the top surface, and a reentrant crack surface of rock 12054. The data suggest that some segregation occurs during impact glass formation leading to surface enrichments in Si and depletions in Mg, Al, Ca, and Ti. The magnitude of the effect appears fairly small, although the complexity of the surfaces severely complicates the data analysis. Because of the complexity of the surfaces, both XPS and SAM data were essential. A search for direct evidence of either solar wind sputter erosion or vapor deposition on the exposed top surface of 12054 provided interesting results which we cannot yet fully interpret. Both this surface and the surface from the re-entrant crack showed enrichments of more than a factor of two in Fe with respect to the bulk.

Housley, R. M.↗
NASA NTRS2020

A Computational Study to Investigate the Effect of Defect Geometries on the Fatigue Crack Driving Forces in Powder-Bed AM Materials

Powder-bed additive manufacturing (AM) processes are associated with the formation of multiple types of process-specific pores, including but not limited to lack-of-fusion (LoF) and keyhole pores. The performance of an AM component is dependent on the type of pores, their density and their proximity to the free surface, and other heterogeneities in the microstructure. In order to characterize the influence of porosity on the mechanical behavior of AM materials, it is imperative to quantitatively analyze the heterogeneous strain accumulation in the vicinity of porosity. Process-specific microstructure models are generated using SPPARKS, an open-source process simulation code. Spherical keyhole or irregular LoF pores are embedded into the microstructure models, which are meshed and input into a finite element code, ScIFEN, to solve for the heterogeneous strain localization in the vicinity of the pores. Given the non-smooth geometries of LoF pores, they readily promote strain accumulation in their vicinity thereby increasing the propensity of initiating fatigue cracks.

Saikumar R Yeratapally↗
NASA NTRS1984

Computer simulation of surface and film processes

All the investigations which were performed employed in one way or another a computer simulation technique based on atomistic level considerations. In general, three types of simulation methods were used for modeling systems with discrete particles that interact via well defined potential functions: molecular dynamics (a general method for solving the classical equations of motion of a model system); Monte Carlo (the use of Markov chain ensemble averaging technique to model equilibrium properties of a system); and molecular statics (provides properties of a system at T = 0 K). The effects of three-body forces on the vibrational frequencies of triatomic cluster were investigated. The multilayer relaxation phenomena for low index planes of an fcc crystal was analyzed also as a function of the three-body interactions. Various surface properties for Si and SiC system were calculated. Results obtained from static simulation calculations for slip formation were presented. The more elaborate molecular dynamics calculations on the propagation of cracks in two-dimensional systems were outlined.

Tiller, W. A.↗
NASA NTRS1995

Supporting technology for the development of Controlled Ecological Life Support Systems (CELSS)

To support the development of Controlled Ecological Life Support Systems (CELSS) in the space program, a metabolic simulator has been selected for use in a closed chamber to test functions of the CELSS. This metabolic simulator is a catalytic reactor which oxidizes the methyl acetate to produce carbon dioxide and water vapor. In this project, kinetic studies of catalytic oxidation of methyl acetate were conducted using monolithic and pellet catalysts with 0.5% (by weight) platinum (Pt) on aluminum oxide (Al2O3). The reaction was studied at a pressure of one atmosphere and at temperatures varying from 160 C to 420 C. By-products were identified at the exit of the preheater and reactor. For the kinetic study with the monolithic catalyst, a linear regression method was used to correlate the kinetic data with zero-order, first-order and Langmuir-Hinshelwood models. Results indicate that the first-order model represents the data adequately at low concentrations of methyl acetate. For higher concentrations of methyl acetate, the Langmuir-Hinshelwood model best represents the kinetic data. Both rate constant and adsorption equilibrium constants were estimated from the regression. A Taguchi orthogonal array (L(sub 9)) was used to investigate the effects of temperature, flow rate, and concentration on the catalytic oxidation of methyl acetate. For the monolithic catalyst, temperature exerts the most significant effect, followed by concentration of methyl acetate. For the pellet catalyst, reaction temperature is the most significant factor, followed by gas flow rate and methyl acetate concentration. Concentrations of either carbon dioxide or oxygen were seen to have insignificant effect on the methyl acetate conversion process. Experimental results indicate that the preheater with glass beads can accomplish thermal cracking and catalytic reaction of methyl acetate to produce acetic acid, methanol, methyl formate, and 1-propanol. The concentration of all by-products was measured in ppmv (parts per million by volume). At higher temperatures, greater amounts of these products are produced, as expected. In all cases, methanol was the predominant concentration detected, followed by methyl formate. At temperatures lower than 320 C for the P-type monolithic catalyst, methanol, acetic acid, and acetone were detected, whereas, for the E-type monolithic catalyst, only methanol was detected at 160 C. Both P and E types of the monolithic catalyst were specified with the same substrates (ceramic), washcoat (Al2O3), and promoter (Pt). However, the manufacturing and treatment procedures were quite different. It was therefore concluded that the performance of the E-type monolithic catalyst is superior to that of the P-type for oxidation of methyl acetate. At higher reaction temperatures, e.g., above 420 C, all reactants and byproducts were completely oxidized using these two types of monolithic catalyst to produce carbon dioxide and water vapor. A complex heterogenous catalytic reaction mechanism was proposed to explain the formation of the byproducts (methanol, acetic acid, and methyl formate) as the methyl acetate traveled through the preheater packed with glass beads. The by-product, 1-propanol, may be formed only through a homogeneous reaction, since it is difficult to develop a reasonable sequence of heterogeneous reaction steps to explain its formation. The homogeneous thermal decomposition of methyl acetate to form free radicals was proposed to explain the formation of 1-propanol, and also methanol, in the preheater. A dual-site catalytic reaction mechanism was proposed for the oxidation of methyl acetate over Pt/Al2O3 monolithic catalyst. The dual-site mechanism describes the chemisorption of oxygen molecules as well as a physical adsorption of methyl acetate on the active sites. On the active sites, methyl acetate is oxidized rapidly to form carbon dioxide and water vapor. A rate equation derived from this mechanism gives the Langmuir-Hinshelwood rate formula which has been observed from the experimental data obtained in this project for high methyl acetate concentration (greater than 1000 ppmv) over a monolithic catalyst. If the oxygen concentration is very high and methyl acetate concentration is very low, the reaction rate equation is then reduced to a first-order with respect to methyl acetate concentration. The first-order model has also been observed from the experimental data obtained in this project for low methyl acetate concentration (less than 1000 ppmv).

Li, Ku-Yen↗
NASA NTRS2017

Environmental Barrier Coating Fracture, Fatigue and High-Heat-Flux Durability Modeling and Stochastic Progressive Damage Simulation

Advanced environmental barrier coatings will play an increasingly important role in future gas turbine engines because of their ability to protect emerging light-weight SiC/SiC ceramic matrix composite (CMC) engine components, further raising engine operating temperatures and performance. Because the environmental barrier coating systems are critical to the performance, reliability and durability of these hot-section ceramic engine components, a prime-reliant coating system along with established life design methodology are required for the hot-section ceramic component insertion into engine service. In this paper, we have first summarized some observations of high temperature, high-heat-flux environmental degradation and failure mechanisms of environmental barrier coating systems in laboratory simulated engine environment tests. In particular, the coating surface cracking morphologies and associated subsequent delamination mechanisms under the engine level high-heat-flux, combustion steam, and mechanical creep and fatigue loading conditions will be discussed. The EBC compostion and archtechture improvements based on advanced high heat flux environmental testing, and the modeling advances based on the integrated Finite Element Analysis Micromechanics Analysis Code/Ceramics Analysis and Reliability Evaluation of Structures (FEAMAC/CARES) program will also be highlighted. The stochastic progressive damage simulation successfully predicts mud flat damage pattern in EBCs on coated 3-D specimens, and a 2-D model of through-the-thickness cross-section. A 2-parameter Weibull distribution was assumed in characterizing the coating layer stochastic strength response and the formation of damage was therefore modeled. The damage initiation and coalescence into progressively smaller mudflat crack cells was demonstrated. A coating life prediction framework may be realized by examining the surface crack initiation and delamination propagation in conjunction with environmental degradation under high-heat-flux and environment load test conditions.

Mechanical creep and fatigue loading condition↗
NASA NTRS2019

Estimation of Delamination Crack Depth Using Passive Thermography

Passive thermography is used to monitor small increases in temperature resulting from delamination damage formation in a composite hat-stiffened panel during quasi-static loading. The heating is composed of two heat generation components. The first component is an instantaneous response due to a strain release during quasi-static loading. The second component is mechanical heating, at the interface of failure, due to fracture damage. This second component produces a transient rise in temperature that is a function of the damage depth and thermal diffusivity. The first component defines the thermal start time for the transient response. A one-dimensional thermal model is used to determine the damage depth. The results are compared to ultrasonic and X-ray CT data. The advantages and limitations of the thermal technique for damage depth detection are discussed.

Zalameda, Joseph N.↗
NASA NTRS2004

Analysis of Europan Cycloid Morphology and Implications for Formation Mechanisms

Europa's highly fractured crust has been shown to contain features with a range of differing morphologies. Most lineaments on Europa are believed to have initiated as cracks, although the type of cracking (e.g. tensile vs. shear) remains unclear and may vary for different morphologies. Arcuate lineaments, called cycloids or flexi, have been observed in nearly all imaged regions of Europa and have been modeled as tensile fractures that were initiated in response to diurnal variations in tides. Despite this hypothesis about the formation mechanism, there have been no detailed analyses of the variable morphologies of cycloids. We have examined Galileo images of numerous locations on Europa to develop a catalog of the different morphologies of cycloids. This study focuses on variations in morphology along individual cycloid segments and differences in cusp styles between segments, while illustrating how morphologic evidence can help unravel formation mechanisms. In so doing, we present evidence for cycloid cusps forming due to secondary fracturing during strike-slip sliding on pre-existing cycloid segments.

Marshall, S. T.↗
NASA NTRS1983

On the alteration of Allende chondrules and the formation of matrix

Recent SEM observations of the Allende chondrules and matrix are reported. Intergrowths of both Fe-rich olivine (with a composition near Fa50), and clinoenstatite (with a composition of about Fs2). All of the clinoenstatite was involved in associations along the outer margins, grain boundaries, and internal crack surfaces of the chondrule. Most of the chondrules also contain abundant opaque inclusions which must have been strongly altered and partially replaced before chondrule formation. It is suggested that the Fe-rich olivine formed from the clinoenstatite by a reaction of the type Fe + 1/202 + MgSiO3 to (Fe,Mg)2SiO4. It is argued that a variation of the small, internally-heated planetesimal provides the most plausible environment for the chemical reaction.

Housley, R. M.↗
NASA NTRSDate not supplied

The Oxidation State of Sulfur in Apollo Samples 71035 and 71055

Lunar apatites contain 100s-1000s ppm sulfur [1-3]. This was initially puzzling because lunar basalts are thought to form, including at the time of apatite crystallization, in low oxygen fugacity (fO2) conditions where sulfur exists in its reduced form (S2-), a substitution not previously observed in natural apatite. It has been recently shown, using S-XANES measurements of the oxidation state of sulfur in apatites and proximal mesostasis in the lunar basalts 12039 and 10044, that sulfur is indeed present as S2- in both the mesostasis glass and apatite when measurements were performed far from cracks or pits in the thin section [4]. This observation is consistent with other mineralogical indications of the low fO2 during formation of these samples (~IW-1) such as the presence of Fe-metal, ulvöspinel, ilmenite, fayalite, and silica in the thin sections. In the same study, in addition to clear spectral evidence for the dominance of S2-, analyses of apatite grains in both samples that occurred near cracks or pits in the thin section sometimes revealed non-negligible spectral evidence (e.g., S6+/ΣS > 0.03; [4]) for the presence of S6+. Because S6+ was not observed in the mesostasis glass near the apatite grains measured, or in any phase far from cracks or pits in the studied thin sections, this S6+ was interpreted as either primary S2- in the sulfide altered to S6+ in the thin section, or S6+ of secondary origin, deposited in the fractures of the samples [4, 5]. Whether this is of lunar or terrestrial origin is unknown but has implications for lunar petrogenesis if lunar [e.g., 5], or sample handling and curation if terrestrial. To test between lunar and terrestrial origins for observed S6+ in Apollo-era thin sections, we will measure the oxidation state of sulfur in apatite and associated phases in a specially frozen sample from a boulder sampled at Station 1A during the Apollo 17 mission as part of the NASA Apollo Next Generation Sample Analysis (ANGSA) program. Here, we present “control” measurements of samples 71035 and 71055, using Apollo era thin sections of aliquots of these rocks that were processed upon return to Earth and since stored under N2 atmospheres at room temperature. These will be compared to measurements using newly made thin sections of aliquots of the same rocks (71035 and 71055). In addition, 71036, which has been in cold storage (-20℃) since the return of the Apollo 17 mission to Earth, has been recently made available through the ANGSA program. With 71036 we can test the effect of storage temperature on potential oxidation of S2- to S6+ in the relatively oxidizing and warm conditions of Earth’s surface.

apollo↗
NASA NTRS1998

Space Shuttle Pinhole Formation Mechanism Studies

Pinholes have been observed to form on the wing leading edge of the space shuttle after about 10-15 flights. In this report we expand upon previous observations by Christensen (1) that these pinholes often form along cracks and are associated with a locally zinc-rich area. The zinc appears to come from weathering and peeling paint on the launch structure. Three types of experimental examinations are performed to understand this issue further: (A) Detailed microstructural examination of actual shuttle pinholes (B) Mass spectrometric studies of coupons containing, actual shuttle pinholes and (C) Laboratory furnace studies of ZnO/SiC reactions and ZnO/SiC protected carbon/carbon reaction. On basis of these observations we present a detailed mechanism of pinhole formation due to formation of a corrosive ZnO-Na-2-O-SiO2 ternary glass, which flows into existing cracks and enlarges them.

Jacobson, Nathan S.↗
NASA NTRS1972

Reliability analysis applied to structural tests

The application of reliability theory to predict, from structural fatigue test data, the risk of failure of a structure under service conditions because its load-carrying capability is progressively reduced by the extension of a fatigue crack, is considered. The procedure is applicable to both safe-life and fail-safe structures and, for a prescribed safety level, it will enable an inspection procedure to be planned or, if inspection is not feasible, it will evaluate the life to replacement. The theory has been further developed to cope with the case of structures with initial cracks, such as can occur in modern high-strength materials which are susceptible to the formation of small flaws during the production process. The method has been applied to a structure of high-strength steel and the results are compared with those obtained by the current life estimation procedures. This has shown that the conventional methods can be unconservative in certain cases, depending on the characteristics of the structure and the design operating conditions. The suitability of the probabilistic approach to the interpretation of the results from full-scale fatigue testing of aircraft structures is discussed and the assumptions involved are examined.

Diamond, P.↗
NASA NTRS1978

Friction and wear of polyethylene oxide polymer having a range of molecular weights

Sliding friction and wear experiments were conducted at light loads (25 to 250 g) with various molecular weights of the polyethylene oxide polymer sliding on itself and iron. Results of the experimental investigation indicate that: (1) the coefficient of friction for the polymer decreases with increasing molecular weight; (2) friction coefficient is higher for the polymer sliding on itself than it is for the polymer sliding on iron; (3) at sufficiently high loads localized surface melting occurs and the friction coefficient is the same for the polymer sliding on itself and iron; (4) fracture cracks develop in the sliding wear track at higher but not lower sliding velocities, reflecting a strain rate sensitivity to crack initiation, and (5) the friction coefficient for the polymer sliding on iron increases with the formation of a polymer film on the iron surface.

Buckley, D. H.↗
NASA NTRS2025

Radiation-Resistant Ti/BN Coatings: Insights From 171 Days Exposure to Space Radiation and Atomic Oxygen in Low Orbit

Atmospheric Plasma Spray (APS) and Vacuum Plasma Spray (VPS) techniques were used to develop Ti/2 vol.% hBN coatings, for extreme space environments and tested aboard the International Space Station as part of the MISSE-17 (Materials International Space Station Experiments) program. The coatings were exposed to atomic oxygen, space radiation, and low-orbit thermal cycling. VPS coatings showed a 56% increase in microhardness, a 26% rise in elastic modulus, minimal porosity and crack density changes compared to APS coatings. The change in mechanical properties is attributed to the formation of TiO, TiO₂ and TiN from nitrogen retention, alongside radiation-induced dislocations, which enhanced surface hardening. The oxidation of titanium led to the formation of TiO and TiO₂, while boron nitride was retained and underwent transmutation in VPS coatings. XPS and EDS analyses confirmed the enhanced space-environment resistance of VPS coatings, making them ideal for long-term spacecraft protection in lunar and Martian conditions.

Abhijith Kunneparambil Sukumaran↗
NASA NTRS2012

Finite Element Modeling of Thermal Cycling Induced Microcracking in Carbon/Epoxy Triaxial Braided Composites

The microcrack distribution and mass change in PR520/T700s and 3502/T700s carbon/epoxy braided composites exposed to thermal cycling was evaluated experimentally. Acoustic emission was utilized to record the crack initiation and propagation under cyclic thermal loading between -55 C and 120 C. Transverse microcrack morphology was investigated using X-ray Computed Tomography. Different performance of two kinds of composites was discovered and analyzed. Based on the observations of microcrack formation, a meso-mechanical finite element model was developed to obtain the resultant mechanical properties. The simulation results exhibited a decrease in strength and stiffness with increasing crack density. Strength and stiffness reduction versus crack densities in different orientations were compared. The changes of global mechanical behavior in both axial and transverse loading conditions were studied. Keywords: Thermal cycles; Microcrack; Finite Element Model; Braided Composite

Zhang, Chao↗