SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The Finite Element Machine is an experimental array processor designed to support research in parallel algorithms and architectures. This report presents a case study of communications using the SENDa and RECV system software routines on the Finite Element Machine, followed by a discussion of the effect of I/O performance on the efficiency of parallel algorithms.
An experimental study of mixing downstream of axial and swirling coaxial jets is being conducted to obtain data for the evaluation and improvement of turbulent transport models currently employed in a variety of computational procedures used throughout the propulsion community. The axial coaxial jet study was completed under Phase 1. The swirling coaxial jet study, which is the subject of this paper, was conducted under Phase 2 of the contract. A TEACH code was acquired, checked out for several test cases, and is reported. A study to measure length scales and to obtain a limited number of measurements with a blunt trailing edge inlet is being conducted under Phase 3 of the contract.
An experimental study was conducted to determine surface pressure distributions on a flat plate with dual subsonic, circular jets exhausting from the surface into a crossflow. The jets were arranged in both side-by-side and tandem configurations and were injected at 90 deg and 60 deg angles to the plate, with jet-to-crossflow velocity ratio of 2.2 and 4. The major objective of the study was to determine the effect of a nonuniform (vs uniform) jet velocity profile, simulating the exhaust of a turbo-fan engine. Nonuniform jets with a high-velocity outer annulus and a low-velocity core induced stronger negative pressure fields than uniform jets with the same mass flow rate. However, nondimensional lift losses (lift loss/jet thrust lift) due to such nonuniform jets were lower than lift losses due to uniform jets. Changing the injection angle from 90 deg to 60 deg resulted in moderate (for tandem jets) to significant (for side-by-side jets) increases in the induced negative pressures, even though the surface area influenced by the jets tended to reduce as the angle decreased. Jets arranged in the side-by-side configuration led to significant jet-induced lift losses exceeding, in some cases, lift losses reported for single jets.
A case study is reported in which the ZnO/SiO2 glass used to package a power rectifier combined with the design to produce a catastropic corrosion failure of the system. Metallic Zn inclusions, present in the glass, played a critical role in creating a conductive path for corrosion currents. Actual equipment failure was the result of an open circuit trace created by corrosion. It is concluded that the presence of Zn inclusions in the glass of this type of package may result in long-term reliability problems for equipment used in high humidity environments.
For fully supersonic flows, an efficient strategy for obtaining numerical solutions is to employ space marching techniques. A full potential marching technique, known as the SIMP code and capable of handling such embedded subsonic regions, has achieved some success analyzing low supersonic Mach number flows. The extension of the full potential approach to the Euler equation which model the exact nonlinear inviscid gas dynamic flow processes is presented. Within the assumption of an inviscid flow, such an Euler marching solver can be applied to a wide class of shocked flows including the hypersonic range. The intent is to maintain some of the basic features of the full potential SIMP code within the Euler solver in dealing with geometry input, gridding techniques, and input/output routines including post processing of results. An Euler marching code known as EMTAC was developed. Results obtained for a variety of configurations involving canard, wing, horizontal tail, flow-through inlet, and fuselage using both the EMTAC and SIMP codes are reported. For shocked cases satisfying the isentropic assumption, the EMTAC and SIMP codes produced practically the same results. In terms of execution time, the EMTAC code is slower.
The one-dimensional standing shock wave is the simplest flow in which nonequilibrium effects may be considered. The direct-simulation Monte Carlo method (DSMC) has yielded excellent agreement with results reported for the case of nitrogen flow at Mach 1.7. The DSMC technique is presently used in conjunction with a variable energy transfer probability model in which energy is transferred between the translational and rotational modes via the Borgnakke-Larsen (1975) phenomenological model.
Today's software systems generally use obsolete technology, are not integrated properly with other software systems, and are difficult and costly to maintain. The discipline of reverse engineering is becoming prominent as organizations try to move their systems up to more modern and maintainable technology in a cost effective manner. JSC created a significant set of tools to develop and maintain FORTRAN and C code during development of the Space Shuttle. This tool set forms the basis for an integrated environment to re-engineer existing code into modern software engineering structures which are then easier and less costly to maintain and which allow a fairly straightforward translation into other target languages. The environment will support these structures and practices even in areas where the language definition and compilers do not enforce good software engineering. The knowledge and data captured using the reverse engineering tools is passed to standard forward engineering tools to redesign or perform major upgrades to software systems in a much more cost effective manner than using older technologies. A beta vision of the environment was released in Mar. 1991. The commercial potential for such re-engineering tools is very great. CASE TRENDS magazine reported it to be the primary concern of over four hundred of the top MIS executives.
Observations of 47 galaxies in the third Case list are reported. Thirty-five of the galaxies in the sample were selected for the presence of emission lines on the objective prism plates. At the higher spectral dispersion of the data, significant line emission was found in 46 of the 47 galaxies. Twenty-six galaxies are found to be undergoing significant bursts of star formation. Ten additional galaxies may be starburst galaxies with low-excitation spectra. Two galaxies are probably type Seyfert 2. The most distant object, CG 200, at a redshift of 0.144, has a strong broad H-alpha emission line, and is probably a Seyfert 1. Seventeen of the galaxies have been detected by IRAS. Eight of the IRAS galaxies have H-II-region-type spectra and eight have low-ionization starburst spectra. The galaxies represent a mixture of types, ranging from intrinsically faint dwarf galaxies with Mb equalling -16 mag, to powerful galaxies with MB equalling -23 mag. Galaxies CG 234 and CG 235 are interacting, as are galaxies CG 269 and CG 270.
The present report describes many cases of airplanes being struck by lightning and the measures that can be taken to minimize damage to them.
With the increased use of computers throughout Goddard Space Flight Center, the Industrial Hygiene Office (IHO) has observed a growing trend in the number of health complaints attributed to poor computer workstation setup. A majority of the complaints has centered around musculoskeletal symptoms, including numbness, pain, and tingling in the upper extremities, shoulders, and neck. Eye strain and headaches have also been reported. In some cases, these symptoms can lead to chronic conditions such as repetitive strain injuries (RSI's). In an effort to prevent or minimize the frequency of these symptoms among the GSFC population, the IHO conducts individual ergonomic workstation evaluations and ergonomics training classes upon request. Because of the extensive number of computer workstations at GSFC, and the limited amount of manpower which the Industrial Hygiene staff could reasonably allocate to conduct workstation evaluations and employee training, a pamphlet was developed with a two-fold purpose: (1) to educate the GSFC population about the importance of ergonomically-correct computer workstation setup and the potential effects of a poorly configured workstation; and (2) to enable employees to perform a general assessment of their own workstations and make any necessary modifications for proper setup.
One important component of a software process is the organizational context in which the process is enacted. This component is often missing or incomplete in current process modeling approaches. One technique for modeling this perspective is the Actor-Dependency (AD) Model. This paper reports on a case study which used this approach to analyze and assess a large software maintenance organization. Our goal was to identify the approach's strengths and weaknesses while providing practical recommendations for improvement and research directions. The AD model was found to be very useful in capturing the important properties of the organizational context of the maintenance process, and aided in the understanding of the flaws found in this process. However, a number of opportunities for extending and improving the AD model were identified. Among others, there is a need to incorporate quantitative information to complement the qualitative model.
It is well established that crystals grown without contact with a container have far superior quality to otherwise similar crystals grown in direct contact with a container. In addition to float-zone processing, detached-Bridgman growth is often cited as a promising tool to improve crystal quality, without the limitations of float zoning. Detached growth has been found to occur quite often during microgravity experiments and considerable improvements of crystal quality have been reported for those cases. However, no thorough understanding of the process or quantitative assessment of the quality improvements exists so far. This project will determine the means to reproducibly grow Ge-Si alloys in the detached mode. Specific objectives include: (1) measurement of the relevant material parameters such as contact angle, growth angle, surface tension, and wetting behavior of the GeSi-melt on potential crucible materials; (2) determination of the mechanism of detached growth including the role of convection; (3) quantitative determination of the differences of defects and impurities among normal Bridgman, detached Bridgman, and floating zone (FZ) growth; (4) investigation of the influence of defined azimuthal or meridional flow due to rotating magnetic fields on the characteristics of detached growth; (5) control time-dependent Marangoni convection in the case of FZ-growth by the use of a rotating magnetic field to examine the influence on the curvature of the solid-liquid interface and the heat and mass transport; and (6) grow high quality GeSi-single crystals with Si-concentration up to 10 at% and diameters up to 20 mm.
It is well established that crystals grown without contact with a container have far superior quality to otherwise similar crystals grown in direct contact with a container. In addition to float- zone processing, detached-Bridgman growth is often cited as a promising tool to improve crystal quality, without the limitations of float zoning. Detached growth has been found to occur quite often during micro-g experiments and considerable improvements of crystal quality have been reported for those cases. However, no thorough understanding of the process or quantitative assessment of the quality improvements exists so far. This project will determine the means to reproducibly grow Ge-Si alloys in the detached mode. Specific objectives include: (1) measurement of the relevant material parameters such as contact angle, growth angle, surface tension, and wetting behavior of the GeSi-melt on potential crucible materials; (2) determination of the mechanism of detached growth including the role of convection; (3) quantitative determination of the differences of defects and impurities among normal Bridgman, detached Bridgman, and Floating Zone (FZ) growth; (4) investigation of the influence of defined azimuthal or meridional flow due to rotating magnetic fields on the characteristics of detached growth; (5) control time-dependent Marangoni convection in the case of FZ-growth by the use of a rotating magnetic field to examine the influence on the curvature of the solid-liquid interface and the heat and mass transport; and (6) grow high quality GeSi-single crystals with Si-concentration up to 10 at% and diameters up to 20 mm.
Crystals grown without contact with a container have far superior quality to otherwise similar crystals grown in direct contact with a container. In addition to float-zone processing, detached-Bridgman growth is a promising tool to improve crystal quality, without the limitations of float zoning. Detached growth has been found to occur frequently during microg experiments and considerable improvements of crystal quality have been reported for those cases. However, no thorough understanding of the process or quantitative assessment of the quality improvements exists so far. This project is determining the means to reproducibly grow Ge-Si alloys in the detached mode.
Crystals grown without being in contact with a container have superior quality to otherwise similar crystals grown in direct contact with a container, especially with respect to impurity incorporation, formation of dislocations, and residual stress in the crystals. In addition to float-zone processing, detached Bridgman growth, although not a completely crucible-free method, is a promising tool to improve crystal quality. It does not suffer from the size limitations of float zoning and the impact of thermocapillary convection on heat and mass transport is expected to be negligible. Detached growth has been observed frequently during (micro)g experiments. Considerable improvements in crystalline quality have been reported for these cases. However, neither a thorough understanding of the process nor a quantitative assessment of the quality of these improvements exists. This project will determine the means to reproducibly grow Pepsi alloys in a detached mode and seeks to compare processing-induced defects in Bridgman, detached-Bridgman, and floating-zone growth configurations in Pepsi crystals (Si less or = 10 at%) up to 20mm in diameter.
For over thirty years now, the H-46 Sea Knight tandem rotor helicopter has operated successfully from the decks of various U.S. Navy ships. There have been approximately 210 thousand landings and takeoffs at sea and the vast majority have occurred without incident. Only a small percent of the total H-46 landings and takeoffs have been less than fully satisfactory. On certain ships, (e.g. the LHA amphibious assault ship) the combination of winds at 15 deg. or so off of the bow and low rotor r.p.m. are conditions under which, on occasion, the rear rotor blades have been observed to flap uncontrollably. Cases have been reported where the rotor blades have struck the H-46 sync-shaft cover during startup and shutdown while the H-46 is sitting on the deck. One life has been lost, several people injured and the repair costs total of the 110+ incidents has been estimated to exceed $20 million. To date, the root cause of this problem has not been identified.
Crystals grown without being in contact with a container have superior quality to otherwise similar crystals grown in direct contact with a container, especially with respect to impurity incorporation, formation of dislocations, and residual stress in the crystals. In addition to float-zone processing, detached Bridgman growth, although not a completely crucible-free method, is a promising tool to improve crystal quality. It does not suffer from the size limitations of float zoning and the impact of thermocapillary convection on heat and mass transport is expected to be negligible. Detached growth has been observed frequently during g experiments. Considerable improvements in crystalline quality have been reported for these cases. However, neither a thorough understanding of the process nor a quantitative assessment of the quality of these improvements exists. This project will determine the means to reproducibly grow GeSi alloys in a detached mode and seeks to compare processing-induced defects in Bridgman, detached-Bridgman, and floating-zone growth configurations in GeSi crystals (Si less than or equal to 10 at%) up to 20mm in diameter. Specific objectives include: measurement of the relevant material parameters such as contact angle, growth angle, surface tension, and wetting behavior of the GeSi-melt on potential crucible materials; determination of the mechanism of detached growth including the role of convection; quantitative determination of the differences in defects and impurities for crystals grown using normal Bridgman, detached Bridgman, and floating zone (FZ) methods; investigation of the influence of a defined flow imposed by a rotating magnetic field on the characteristics of detached growth; control of time-dependent Marangoni convection in the case of FZ growth by the use of a rotating magnetic field to examine the influence on the curvature of the solid-liquid interface and the heat and mass transport; and growth of benchmark quality GeSi-single crystals.
We report a multipoint case study of the electromagnetic equatorial noise observed by the Cluster project. High-resolution data were measured in three close points in space located in the morning sector of the outer plasmasphere. We demonstrate a narrow latitudinal extent of the emissions with a typical width of 2 degrees, centered near the minimum-B equator. Power spectra recorded by the different satellites show a complex structure of emission lines whose relative intensities and positions vary at timescales of 1-2 min and/or at spatial scales of tens of wavelengths. These lines do not match harmonics of the local proton cyclotron frequency, as it would be expected if the waves are generated by energetic ions and observed near the source region. We bring observational evidence that the waves propagate with a significant radial component and thus can propagate from a distant generation region located at different radial distances where ion cyclotron frequencies match the observed fine structure.