Search NASA⌕ Search

SEARCH · Search NASA

Results for “Ceramic Capacitor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

Modified giant dielectric properties of samarium doped CaCu{sub 3}Ti{sub 4}O{sub 12} ceramics

Highlights: ► Grain size of CaCu{sub 3}Ti{sub 4}O{sub 12} ceramics was greatly decreased by doping with Sm{sup 3+}. ► ε′ and tan δ decreased with increasing the concentration of Sm{sup 3+} doping. ► Ca{sub 0.925}Sm{sub 0.05}Cu{sub 3}Ti{sub 4}O{sub 12} exhibited ε′ ∼ 10,863 and low tan δ ∼ 0.043 at 20 °C and 1 kHz. -- Abstract: Effects of Sm{sup 3+} substitution on the microstructure and dielectric properties of CaCu{sub 3}Ti{sub 4}O{sub 12} ceramics were investigated. The grain size of CaCu{sub 3}Ti{sub 4}O{sub 12} ceramics was greatly decreased by doping with Sm{sup 3+}, resulting from the ability of Sm{sup 3+} to inhibit the grain growth rate. This result can cause a decrease in the dielectric constant (ε′) and loss tangent (tan δ) of CaCu{sub 3}Ti{sub 4}O{sub 12} ceramics. Interestingly, high dielectric permittivity (ε′ ∼ 10,863) and low loss tangent (tan δ ∼ 0.043 at 20 °C and 1 kHz) were observed in the Ca{sub 0.925}Sm{sub 0.05}Cu{sub 3}Ti{sub 4}O{sub 12} ceramic. Nonlinear electrical properties of CaCu{sub 3}Ti{sub 4}O{sub 12} ceramics were modified by doping with Sm{sup 3+}. The dielectric relaxation behavior of Sm-doped CaCu{sub 3}Ti{sub 4}O{sub 12} ceramics can be well ascribed based on the internal barrier layer capacitor model of Schottky barriers at the grain boundaries.

36 MATERIALS SCIENCE↗

Substitution of Pb with (Li 1/2 Bi 1/2 ) in PbZrO 3 -based antiferroelectric ceramics

PbZrO 3 -based antiferroelectric (AFE) ceramics are promising dielectrics for high-energy-density capacitors due to their reversible phase transitions during charge–discharge cycles. In this work, a new composition series, [Pb 0.93–x La 0.02 (Li 1/2 Bi 1/2 ) x Sr 0.04 ][Zr 0.57 Sn 0.34 Ti 0.09 ]O 3 , with Li + and Bi 3+ substitution of Pb 2+ at x=0 , 0.04, 0.08, 0.12, 0.16 is investigated for the microstructure evolution, ferroelectric (FE) and dielectric properties. It is found that Li + and Bi 3+ substitution can significantly reduce the sintering temperature and simultaneously enhance the dielectric breakdown strength. An ultrahigh energy efficiency (94.0%) and a large energy density (3.22J/cm 3 ) are achieved in the composition of x = 0.12 with a low sintering temperature (1075°C).

36 MATERIALS SCIENCE↗

Solid-state resistor for pulsed power machines

A flexible solid-state resistor comprises a string of ceramic resistors that can be used to charge the capacitors of a linear transformer driver (LTD) used in a pulsed power machine. The solid-state resistor is able to absorb the energy of a switch prefire, thereby limiting LTD cavity damage, yet has a sufficiently low RC charge time to allow the capacitor to be recharged without disrupting the operation of the pulsed power machine.

36 MATERIALS SCIENCE↗

Aerosol Deposition: Room Temperature Solid-State Deposition of Ceramics

The ability to integrate ceramics with other materials has been limited by the high temperature s (>800C) associated with ceramic processing. A novel process, known as aerosol deposition (AD), capable of preparing ceramic films at room temperature (RT) has been the subject of recent interest in the thermal spray and microelectronics communities. In this process, ceramic particles are accelerated using pressurized gas, impacted on a substrate and form a dense film under vacuum. This revolutionary process eliminates high temperature processing, enabling new coatings and microelectronic device integration as a back end of line process, in which ceramics can be deposited on metals, plastics, and glasses . Future impact s of this technology on Sandia's mission could include improved ceramic integration, miniaturized magnetic circulators in radar applications, new RF communication products, modification of commercial - off - the - shelf electronics, fabrication of conformal capacitors, thin batteries, glass - to - metal seals, and transparent electronics. Currently, optimization for RT solid - state deposition of ceramics is achieved empirically and fundamental mechanisms for ceramic particle - particle bonding are not well understood. Obtaining this knowledge will allow process - microstructure - property relation ship realization and will enable a differentiating ceramic integration capability. This LDRD leveraged Sandias existing equipment and capabilities in simulation, experimentation, and materials characterization to discover the fundamental mechanisms for ceramic particle deformation, particle - substrate bonding, and particle - particle bonding in RT consolidated films. RT deformation of individual Al 2 O 3 particles was examined computationally and experimentally as a model system for understanding the complex dynamics associated with in vacuo RT deposition conditions associated with AD. Subsequently, particle - substrate bonding and particle - particle bonding in AD Al 2 O 3 consolidated films were examined computationally and experimentally. Fundamental mechanisms behind the AD process were proposed.

36 MATERIALS SCIENCE↗

Casting Of Multilayer Ceramic Tapes

Procedure for casting thin, multilayer ceramic membranes, commonly called tapes, involves centrifugal casting at accelerations of 1,800 to 2,000 times normal gravitational acceleration. Layers of tape cast one at a time on top of any previous layer or layers. Each layer cast from slurry of ground ceramic suspended in mixture of solvents, binders, and other components. Used in capacitors, fuel cells, and electrolytic separation of oxygen from air.

Collins, Earl R., Jr.↗

Circuit model of the ITER-like antenna for JET and simulation of its control algorithms

The ITER-like Antenna (ILA) for JET [1] is a 2 toroidal by 2 poloidal array of Resonant Double Loops (RDL) featuring in-vessel matching capacitors feeding RF current straps in conjugate-T manner, a low impedance quarter-wave impedance transformer, a service stub allowing hydraulic actuator and water cooling services to reach the aforementioned capacitors and a 2nd stage phase-shifter-stub matching circuit allowing to correct/choose the conjugate-T working impedance. Toroidally adjacent RDLs are fed from a 3dB hybrid splitter. It has been operated at 33, 42 and 47MHz on plasma (2008-2009) while it presently estimated frequency range is from 29 to 49MHz. At the time of the design (2001-2004) as well as the experiments the circuit models of the ILA were quite basic. The ILA front face and strap array Topica model was relatively crude and failed to correctly represent the poloidal central septum, Faraday Screen attachment as well as the segmented antenna central septum limiter. The ILA matching capacitors, T-junction, Vacuum Transmission Line (VTL) and Service Stubs were represented by lumped circuit elements and simple transmission line models. The assessment of the ILA results carried out to decide on the repair of the ILA identified that achieving routine full array operation requires a better understanding of the RF circuit, a feedback control algorithm for the 2nd stage matching as well as tighter calibrations of RF measurements. The paper presents the progress in modelling of the ILA comprising a more detailed Topica model of the front face for various plasma Scrape Off Layer profiles, a comprehensive HFSS model of the matching capacitors including internal bellows and electrode cylinders, 3D-EM models of the VTL including vacuum ceramic window, Service stub, a transmission line model of the 2nd stage matching circuit and main transmission lines including the 3dB hybrid splitters. A time evolving simulation using the improved circuit model allowed to design and simulate the effectiveness of a feedback control algorithm for the 2nd stage matching and demonstrates the simultaneous matching and control of the 4 RDLs: 11 feedback loops control 21 actuators (8 capacitors, 4 phase shifters and 4 stubs for the 2nd stage matching, 4 main phase shifters controlling of the toroidal phasing and the electronically controlled phase between RF sources feeding top and bottom parts of the array and determines the poloidal phasing of the array which is solved explicitly at each time step) on (simulated) ELMy plasmas.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Embedded Resistors and Capacitors in Organic and Inorganic Substrates

Embedded resistors and capacitors were purchased from two technology; organic PWB and inorganic low temperature co-fire ceramic (LTCC). Small groups of each substrate were exposed to four environmental tests and several characterization tests to evaluate their performance and reliability. Even though all passive components maintained electrical performance throughout environmental testing, differences between the two technologies were observed. Environmental testing was taken beyond manufacturers' reported testing, but general not taken to failure. When possible, data was quantitatively compared to manufacturer's data.

printed circuit board (PCB)↗

Polarization Mechanisms in P(VDF-TrFE) Ferroelectric Thin Films

Ferroelectric polymers have amassed tremendous attention due to several attractive properties including high breakdown strength, low dielectric loss, relatively fast charge/discharge rates and greater flexibility than their ceramic counterparts. In order to achieve enhanced energy efficiency in high-energy storage capacitor applications, it is desirable to obtain slim polarization hysteresis loops for ferroelectric polymer films. Here, it has been demonstrated that promotion of large crystallites and γ phase content through thermal annealing provides a cost-effective way to obtain a quasi-linear polarization response in a PVDF co-polymer thin film. The polarization mechanisms underlying a thin hysteresis loop in the thermally annealed film are elucidated using direct experimental insights from in situ synchrotron diffraction with two-dimensional detection. It has been demonstrated that the susceptibility for electric-field-induced structural changes is higher in the defective ferroelectric γ phase than the polar phase β, due to a higher flexibility for accommodation of gauche bond along the carbon chain. In addition, the polymer chains in the γ phase also exhibit a range of different responses depending on their orientations with respect to the electric field. These conclusions are broadly significant as they provide a fundamental basis for rational design of phase assemblages to obtain tailor-made properties in ferroelectric polymer films.

36 MATERIALS SCIENCE↗

Sol-gel Technology and Advanced Electrochemical Energy Storage Materials

Advanced materials play an important role in the development of electrochemical energy devices such as batteries, fuel cells, and electrochemical capacitors. The sol-gel process is a versatile solution for use in the fabrication of ceramic materials with tailored stoichiometry, microstructure, and properties. This processing technique is particularly useful in producing porous materials with high surface area and low density, two of the most desirable characteristics for electrode materials. In addition,the porous surface of gels can be modified chemically to create tailored surface properties, and inorganic/organic micro-composites can be prepared for improved material performance device fabrication. Applications of several sol-gel derived electrode materials in different energy storage devices are illustrated in this paper. V2O5 gels are shown to be a promising cathode material for solid state lithium batteries. Carbon aerogels, amorphous RuO2 gels and sol-gel derived hafnium compounds have been studied as electrode materials for high energy density and high power density electrochemical capacitors.

Chung-tse Chu↗

Advanced Power Electronics Components

This paper will give a description and status of the Advanced Power Electronics Materials and Components Technology program being conducted by the NASA Glenn Research Center for future aerospace power applications. The focus of this research program is on the following: 1) New and/or significantly improved dielectric materials for the development of power capacitors with increased volumetric efficiency, energy density, and operating temperature. Materials being investigated include nanocrystalline and composite ceramic dielectrics and diamond-like carbon films; 2) New and/or significantly improved high frequency, high temperature, low loss soft magnetic materials for the development of transformers/inductors with increased power/energy density, electrical efficiency, and operating temperature. Materials being investigated include nanocrystalline and nanocomposite soft magnetic materials; 3) Packaged high temperature, high power density, high voltage, and low loss SiC diodes and switches. Development of high quality 4H- and 6H- SiC atomically smooth substrates to significantly improve device performance is a major emphasis of the SiC materials program; 4) Demonstration of high temperature (> 200 C) circuits using the components developed above.

Schwarze, Gene E.↗

Overview of NASA Ultracapacitor Technology

NASA needed a lower mass, reliable, and safe medium for energy storage for ground-based and space applications. Existing industry electrochemical systems are limited in weight, charge rate, energy density, reliability, and safety. We chose a ceramic perovskite material for development, due to its high inherent dielectric properties, long history of use in the capacitor industry, and the safety of a solid state material.

Hill, Curtis W.↗

Overview of NASA Ultracapacitor Technology

NASA needed a lower mass, reliable, and safe medium for energy storage for ground-based and space applications. Existing industry electrochemical systems are limited in weight, charge rate, energy density, reliability, and safety. We chose a ceramic perovskite material for development, due to its high inherent dielectric properties, long history of use in the capacitor industry, and the safety of a solid state material.

Hill, Curtis W.↗

Design and Assembly Process Implementation for Embedding Passive and Active Components Introduction to IPC-7092

"This presentation describes the design and assembly challenges for implementing passive and active components, in either formed or inserted methodology, into a printed board. The completed structure including internal electronic components is ready for surface mount and/or through-hole component attachment. The multilayered structure becomes a complete product ready for further processing in an assembly process and be made from organic, inorganic (ceramic) or both types of material."

embedded circuitry↗

Direct cooled power electronics substrate

The disclosure describes directly cooling a three-dimensional, direct metallization (DM) layer in a power electronics device. To enable sufficient cooling, coolant flow channels are formed within the ceramic substrate. The direct metallization layer (typically copper) may be bonded to the ceramic substrate, and semiconductor chips (such as IGBT and diodes) may be soldered or sintered onto the direct metallization layer to form a power electronics module. Multiple modules may be attached to cooling headers that provide in-flow and out-flow of coolant through the channels in the ceramic substrate. The modules and cooling header assembly are preferably sized to fit inside the core of a toroidal shaped capacitor.

Wiles, Randy H↗

Effect of Dielectric Selection on Sintering Behavior of LTCC

Low Temperature Cofired Ceramic (LTCC) is a versatile ceramic packaging technology. LTCC’s functionality and performance can be enhanced with the incorporation of passive devices such as resistors, capacitors, and inductors into the structure of the substrate. This incorporation, which eliminates surface mount solder joints is desirable for improving system reliability and allows for increased package density. Commercially available dielectrics for embedding capacitors into LTCC are limited and the incorporation of such systems into LTCC substrates poses processing challenges related to material compatibility. This paper will review multiple dielectric systems and techniques for embedding capacitors into LTCC as well as present new data related to the cofiring behavior of LTCC and custom dielectrics.

36 MATERIALS SCIENCE↗

3D-ink-printing of monocrystalline YBCO superconductor

Single-crystal microstructure can bring high performance for many materials includingpiezoelectrics1, 2, semiconductors3, 4, and cuprate superconductors5. Unlike single-crystal metalsthat can be machined into complex components6, most single-crystal ceramics are limited to theshape of thin films or plates due to their brittleness. However, more designs of advanced devicesneed to break these geometric limitations. 3D-ink-printing can efficiently fabricate complex architectured ceramics, but the microstructure is polycrystals. Here, for the first time, we demonstrate a route to grow single-crystal on 3D printed ceramic-YBa2Cu3O7-x (YBCO)superconductors that can simultaneously have complex architectures and high critical currentdensity. An ink containing precursor powders was 3D extruded and sintered to obtain polycrystalYBCO micro-lattices. A single-crystal seed is then utilized to grow single crystal on 3D-printedmicro-lattices by melt growth method. We found that the geometric details of 3D printed microlatticecan survive after it went through liquid + solid phase region above its peritectic temperature.More complex YBCO single-crystal parts, such as horizontal and toroidal coils, were thensuccessfully fabricated. In addition, Origami can be implemented on our 3D printed sample to increase their complexity. This research provides a new way to develop superconducting devicessuch as undulators for synchrotron radiation and microwave cavities for dark-matter axion search7.We expect this new process will inspire more studies about 3D printing of single-crystal ceramics. For example, 3D printing of BaTiO3 can be developed to grow a single crystal8 for the applications of dielectric capacitors and transducers.

43 PARTICLE ACCELERATORS↗

Epitaxy of Zn{sub 2}TiO{sub 4} (1 1 1) thin films on GaN (0 0 1)

Highlights: ► High-permittivity spinel Zn{sub 2}TiO{sub 4} thin films were grown on GaN (0 0 1) by sputtering. ► Oxygen atmosphere and post heat-treatment annealing effectively enhanced epitaxy. ► The epitaxial Zn{sub 2}TiO{sub 4} modifies the dielectric properties of ceramic oxide. - Abstract: High-permittivity spinel Zn{sub 2}TiO{sub 4} thin films were grown on GaN (0 0 1) by rf-sputtering. Grazing-angle, powder, and pole-figure X-ray diffractometries (XRD) were performed to identify the crystallinity and the preferred orientation of the Zn{sub 2}TiO{sub 4} films. Lattice image at the Zn{sub 2}TiO{sub 4} (1 1 1)/GaN (0 0 1) interface was obtained by high-resolution transmission-electron microscopy (HR-TEM). An oxygen atmosphere in sputtering and post heat-treatment using rapid thermal annealing effectively enhanced the epitaxy. The epitaxial relationship was determined from the XRD and HR-TEM results: (111){sub Zn{sub 2TiO{sub 4}}}||(001){sub GaN}, (202{sup ¯}){sub Zn{sub 2TiO{sub 4}}}||(110){sub GaN},and[21{sup ¯}1{sup ¯}]{sub Zn{sub 2TiO{sub 4}}}||[01{sup ¯}10]{sub GaN}. Finally, the relative permittivity, interfacial trap density and the flat-band voltage of the Zn{sub 2}TiO{sub 4} based capacitor were ∼18.9, 8.38 × 10{sup 11} eV{sup −1} cm{sup −2}, and 1.1 V, respectively, indicating the potential applications of the Zn{sub 2}TiO{sub 4} thin film to the GaN-based metal-oxide-semiconductor capacitor.

36 MATERIALS SCIENCE↗