Search NASA⌕ Search

SEARCH · Search NASA

Results for “Composites Load Testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Advanced Coating Compositions and Microstructures to Improve Uptime and Operational Flexibility in Cyclic, Low-Load Thermal Utility Plants

GE, the University of Tennessee, and Oak Ridge National Laboratory collaborated from 2020 to 2023 developing two key technologies for improving the viability of fuel switching and load following in thermal utility plants: a) cost-effective weld overlay compositions for boiler tubing b) cathodic arc coatings that deliver improvements in both erosion resistance and oxidation resistance in high temperature steam for HP turbine blades The team worked through a robust, logical project map to de-risk these two technologies and advance them from TRL 3 to TRL 6. For the cost-effective weld overlay, the team developed a ferritic filler material which was fabricated at a vendor for 18% the average market cost of Inconel 625 wire, had a corrosion rate 3x lower in conditions simulating a biomass-fired superheater and 10x lower in conditions simulating a coal-fired superheater, and was fabricated into prototype overlaid tubing that passed ASME requirements including transverse bending, dye penetrant inspection, and ASTM G-76 evaluation. For the cathodic arc coatings applied to steam turbine blades, the team developed a novel composition that was successfully transferred to a qualified vendor. The vendor was able to produce coated prototypes with 4x the as-deposited erosion resistance and 10.4x the post-steam-exposure erosion resistance of the TiN coating the vendor currently applies on GE steam turbine components, without significantly increasing process cost. These coated prototypes also passed a GE inspection and showed favorable performance in high temperature erosion, nanoindentation, sliding wear, scratch adhesion, and high cycle fatigue testing. If successfully deployed by GE, it is anticipated that the technologies will enable the following: • 25%-50% increase in time between outages for both boilers and HP turbines. • 50% decrease in cost for weld overlay on a per foot basis relative to todays NiCr alloys. • Adequate oxidation resistance and erosion for HP turbine inlet steam at >620°C and >220 bar. • No need for changes in component supply chain or any notable Capital Expenditures. 5 Decreasing component cost, increasing performance, and extending time between outages represent direct value propositions to GE and their customers. For the American consumer, these objectives translate into increased grid reliability (fewer unexpected outages), decreased Levelized Cost of Electricity, and improved environmental health (low-loading/load following to accelerate penetration of renewables). The results also have implications for wear resistant tooling, wire arc additive manufacturing, more durable components for syngas cleanup, and deployment of more efficient thermochemical pathways for carbon negative fuel production

09 BIOMASS FUELS↗
DOE OSTI2022

Fabrication and accelerated long-term stability test of asymmetrical hollow fiber-supported thin film oxygen separation membrane

Asymmetrical hollow fiber-supported thin film membrane may provide microstructural advantages for air separation and oxygen production. The fabrication of such a membrane is usually very difficult, particularly the sintering behaviors and thermal expansion coefficient (TEC) mismatch among multiple layers. This directly affects the reliability and long-term stability of the membrane. Here, in this research, the sintering behaviors of a set of simple oxides are systematically studied and ZnO is identified as a material component for composite substrate La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3-δ (LSCF)-ZnO. The LSCF-ZnO ratios are further optimized by trading off several factors, e.g., matching the sintering behaviors and TECs of the LSCF-ZnO composite with those of LSCF thin film separation layer while enhancing the substrate strength. With the identified LSCF-ZnO ratio, the LSCF-ZnO composite hollow fiber substrate precursor is formed through slurry spinning process with porous microstructure being formed via phase inversion process. The thin film LSCF dense separation layer is then dip-coated on the substrate followed by co-sintering process. A thin, porous PrBaCo(Fe 0.6 Zr 0.2 Y 0.2 )O 5+δ (PBCFZY) catalyst layer is fabricated on the dense LSCF separation layer with dip-coating and sintering process, forming an asymmetrical membrane device LSCF-ZnO/LSCF/PBCFZY. Oxygen permeation test of the device is systematically conducted, and the fundamental mechanisms are analyzed. An accelerated long-term stability test of the membrane is also conducted (~550h, 46 thermal cycling loads), demonstrating excellent robustness and durability. The device is characterized and analyzed before and after the test. By replacing a considerable amount of high cost LSCF with low cost ZnO in the substrate, it not only enhances the stability but also reduces the capital cost of the membrane for practical applications.

42 ENGINEERING↗
DOE OSTI2022

High-temperature superelasticity in NiTiPt and NiTiPd shape memory alloys

Alloying NiTi shape memory alloys with sufficient Pt and Pd at the expense of Ni has been shown to increase transformation temperatures well above those possible with the binary composition, enabling consideration of a new class of high-temperature mechanical sensors and actuators. To achieve shape memory behavior at temperatures greater than 200 °C, previous studies of NiTiPt and NiTiPd compositions have focused primarily on alloys with greater than 16 at.% Pt and 25 at.% Pd. While generally not the focus, none of these previous studies demonstrated superelastic behavior at high temperatures. In an effort to identify alloys that transform to austenite at approximately 200 °C and exhibit superelastic behavior with recoverable strains greater than 2%, a series of Ti-rich NiTiPt ternary alloys with 15.5–16.5 at.% Pt, and Ti-rich NiTiPd ternary alloys with 25–26 at.% Pd have been targeted. The polycrystalline alloys were processed via arc melting followed by homogenization heat treatment. Thermomechanical properties were measured using electro-discharge machined tension test coupons and a miniature load frame equipped with a clamshell furnace. Ultimately, superelasticity in uniaxial tension with clear plateau regions was demonstrated and characterized in these alloys at temperatures between 219 °C and 270 °C.

Massad, Jordan E.↗
DOE OSTI2023

Waste Glass Property Database and Data Qualification Plan

The U.S. Department of Energy vitrification facilities currently employ glass property-composition models to ensure processability of waste streams and acceptability of the final glass products. The efficiency (e.g., process flexibility, reduced down time, and reduced cost) of waste vitrification is directly tied to the size of the waste processing envelope. To increase the size of the processing envelope, a larger database was developed. The database will improve the prediction accuracy of glass properties, leading to higher waste loadings, higher waste throughput, broader process flexibility, and reduced mission life. Some of the data in this expanded database has insufficient quality assurance (QA) rigor for use in nuclear facility operation and glass qualification. A plan was developed to qualify high-value data under the appropriate QA rigor for use at the Hanford Waste Treatment and Immobilization Plant’s High-Level Waste (HLW) Facility. This qualification plan first compares the data coverage over the composition region of interest to Hanford HLW by property. Those studies that significantly improve the data coverage in the Hanford HLW glass composition region were prioritized for qualification activities. Qualification methods including QA equivalence, peer review, data corroboration, and confirmatory testing have been assigned to each high-priority study.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Metallurgical and mechanical characterization of ATP-5 aluminum alloys for minimizing machining distortion

ATP-5 aluminum alloy was considered as an alternative to 6061-T651 aluminum alloy to minimize machining distortion. ATP-5 is a proprietary cast alloy that is compositionally similar to 5083 aluminum and is purported to have excellent machinability, stability, and corrosion response. Dimensional stability tests, mechanical testing, chemical analysis, microstructural analysis, and fractography were completed to understand the metallurgy of the ATP-5 alloy and assess its potential as a 6061-T651 alloy alternative. Ultimately, the ATP-5 was found to retain dimensional stability issues, albeit to a lesser extent, relative to the 6061-T651 alloy. Combined with the residual cast structure observed microstructurally and lot-to-lot mechanical property variation, the alloy was deemed not suitable for a structural application. Alternative uses of ATP-5 include tooling, molds, vacuum chucks, fixtures, and jigs, where the material can shine in non-load bearing applications with a need for dimensional control and machinability.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Characterization of the Fusion Zone in Laser Beam Welds on SS304L

Designing a welded joint requires consideration of the welding process, component/assembly structure and weld geometry, material composition, properties, and desired joint performance. The designer must also specify a set of acceptance criteria used to evaluate the welds. This study was conducted to support the design team responsible for specifying the spot weld profile by investigating the relationship between weld process parameters and the weld geometry and properties to further inform design optimization. The subjects of this study are two thin stainless steel 304L (SS304L) components joined by Laser Beam Welding (LBW). The components are the Housing, which contains flexible circuitry, and the Cover that protects the circuitry during handling, installation, and under service loads. Figure 1 illustrates coupon versions of the Cover and Housing used to simulate the interface between these components for weld testing. These coupon representations of assembly components were designed to match the material and relevant geometry related to the welded joint while other features not relevant to the welded joint are excluded.The objective of this study was to characterize the sensitivity of the weld geometry and mechanical properties to the input weld parameters to inform further Finite Element Analysis (FEA) efforts in balancing joint strength against assembly deformation caused by the welding process. Characterization was accomplished by varying laser welding parameters around the current design values and measuring weld geometry on the cross-sections. Nanoindentation with a spherical and flat-ended tip was used on polished section cuts of the weld to obtain direct estimates of the stress-strain response of the Fusion Zone (FZ) for comparison to the Base Metal (BM).

42 ENGINEERING↗
DOE OSTI2026

Melter Tests to Define LAW Halide Concentrations, Phase 2

The present work represents the second of two phases to address the formation of secondary sulfate phases while processing high waste loading LAW formulations with elevated halide, chromium, and phosphate feed concentrations over a wide range of LAW waste types, including those with high potassium concentrations. The Test Plan for the present work outlines a series of tests designed to assess the formation of secondary phases over a range of sulfur and halide concentrations for two LAW streams and associated glass formulations as well as crucible testing to identify additives that have the potential to suppress the formation of secondary phases for wastes with high chlorine contents. The combined results from both phases of testing and from previous tests with these LAW waste streams will be used as inputs to future work to develop concentration limits for these components in the LAW glass property composition models and to support the modification and updating of the current WTP LAW glass formulation algorithm.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Iodine capture with mechanically robust heat-treated Ag-Al-Si-O xerogel sorbents

Silver-loaded heat-treated aluminosilicate xerogels (Ag-HTX) were evaluated as sorbents for iodine [I2(g)] capture. The heat treatment step was performed to help increase the mechanical integrity of the gels. The synthesized xerogels were characterized using powder X-ray diffraction, scanning electron microscopy, energy-dispersive X-ray spectroscopy, transmission electron microscopy, Brunauer-Emmett-Teller analysis, gravimetric iodine loading, nanoindentation, and dynamic mechanical analysis. The structural and chemical analyses of Ag-HTX showed uniform distribution of Ag throughout the gel network after Ag-exchange. After I2(g) capture, the AgI crystallites were observed in the sorbent verifying chemisorption as the iodine capture mechanism. Iodine loading of this xerogel was 0.43 g g-1 at 150°C over 1 d and 0.52 g g-1 at 22°C over 33 d. The specific surface area of Ag-HTX was 202 m2 g-1 and decreased to 87 m2 g-1 after iodine loading. The hardness of the heat-treated xerogel was 160 times higher than heat-treated aerogel of the same composition. The heat-treatment process increased the modulus value to 40.77 MPa from 6.99 MPa of as-made xerogel, demonstrating the need for this added step in the synthesis process. These results show that Ag-HTX is a promising sorbent for I2(g) capture with good loading capacity and mechanical stability.

xerogels, aerogels, iodine capture, hardness testi↗
DOE OSTI2024

Assessment of frequency and amplitude dependence on the cyclic degradation of polyurethane foams

Many energy absorption applications utilize flexible polymeric foams for their viscoelastic properties. It is desired that the material will perform consistently across repeated compression cycles. This study examines the effect of fatigue at low strain rates on the viscoelasticity of open-cell polyurethane foam. Six polyurethanes of the same base composition with two porosities (70% and 80%) and three chemical indexes (79i, 100i, and 121i) are tested. Large deformation cyclic compression of the foams is conducted on a universal testing system (UTS). These data are then post-processed leveraging dynamic mechanical analysis Fourier transform rheology to characterize changes in the viscoelasticity of the materials over fatigue cycles. Results show that foams can increase or decrease in stiffness up to 10% over 10 4 cycles. Specifically, higher chemical index, higher excitation frequency, and larger excitation amplitude correlate with a more pronounced decrease in stiffness. Damping can also change by 15% and correlates with chemical index and excitation frequency. Consequently, the findings suggest that internal foam structure and bulk material properties as well as applied loading parameters affect the viscoelastic fatigue response of flexible polymeric foams.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Liquefaction of pelleted corn cobs

Liquid slurries at high loadings (pumpable slurries) are critical to handle the streams between the unit operations in a biorefinery. Their liquefaction potential was initially tested with a small-scale method using 3FPU Ctec-2 /g dry biomass, and results were confirmed in 1L bioreactors experiments. Liquid slurries of cobs were observed in small scale tests (based on visual appearance, and reducing sugars released). Results were confirmed in 1L bioreactors under similar experimental conditions. Yield stress value in bioreactor was 34 ± 6Pa at 96 h, and glucan and xylan conversion to glucose and xylose, respectively, were 41 and 21%. In addition, work has been initiated with liquefaction of other pelleted corn stover fractions: Husk/Leaf (A),Husk (B), Stems (D) and controls (whole corn stover; F and G). Compositional analysis of the pellets showed glucan content (%) in the samples ranged from 31.9 to 36.1, xylan from 19.1 to 20.9, total lignin 13.1 to 18.8,and total ash 1.73 to 10.19. The moisture content ranged from 6.21 to 11.66%. Given these similar characteristics, we also examined liquefaction of these other samples, and they also showed that liquid slurries are possible. Work is continuing to define favourable conditions for liquid slurries formation.

Cruz, Antonio↗
DOE OSTI2021

Slipstream Testing of Amine-Based Solvents at a Low-Rank Coal-Fired Power Plant

Conference presentation for 38th Annual International Pittsburgh Coal Conference, Virtual, September 20–23, 2021. To better assess mitigation strategies for aerosol reduction to extend solvent life, the University of North Dakota Energy & Environmental Research Center (EERC) installed a pilot-scale CO 2 absorption system at a lignite-fired plant in central North Dakota. The pilot-scale system was operated using both commercial KS-1™ solvent and advanced KS-21™ solvent provided by Mitsubishi Heavy Industries (MHI). MHI’s proprietary amine emission reduction unit (AERU™) technology was installed downstream of the absorber columns to reduce solvent losses by recovering amines at the system outlet. Fine particulate loading was measured throughout the capture system with and without a WESP operating and using both solvents. Captured particulate was brought back to the EERC to be analyzed for chemical composition and to be examined by scanning electron microscopy for particulate structure. These variables were then correlated to performance of particulate control devices in reducing aerosol formation and solvent losses.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2022

Uniform lithiophilic layers in 3D current collectors enable ultrastable solid electrolyte interphase for high-performance lithium metal batteries

Uniform lithium plating/stripping during charging/discharging in 3D lithiophilic current collectors (3DLCC) is essential to suppress growth of lithium dendrites and to mitigate infinite volume variations of lithium metal for long-lived lithium metal batteries. Additionally, this study reveals the decisive role played by uniformity of the lithiophilic layer of the 3DLCC in achieving uniform lithium plating/stripping. Herein, a series of metal oxide-based 3DLCCs are successfully fabricated with a simple and an ultrafast solution combustion method, from which formation of a uniform and stable lithium dendrite-free solid electrolyte interphase via a uniform lithiophilic layer is demonstrated. Taking Co 3 O 4 as the lithiophilic material deposited on a nickel foam as the 3DLCC (Co@NF) for a proof of concept, the loading amount of Co 3 O 4 , closely correlated with the uniformity of the Co 3 O 4 layer, is modulated to optimize its lithium ion hosting performances. With a uniform Co 3 O 4 layer grown in the 3DLCC, an ultralow nucleation overpotential of 33.4 mV is achieved in half-cell tests at 1 mA cm -2 and 1 mAh cm -2 , and a high Coulombic efficiency of 97.1% is maintained after 210 cycles under a severe cycling condition of 2 mA cm -2 and 1 mAh cm -2 . A small polarization voltage of 13 mV together with an ultralong cycle life of 2400 h at 0.5 mA cm -2 and 1 mAh cm -2 in symmetric Li cells is achieved. Moreover, the composite Li anode delivers sensational rate capability and cyclability in full-cells. This work not only provides new and valuable insights into the interphasial chemistry of solid electrolyte interphase layers, but also sheds light on the development of ultrastable lithium metal batteries.

25 ENERGY STORAGE↗
DOE OSTI2025

Multimetallic Layered Composites (MMLCs) for Rapid, Economical Advanced Reactor Deployment (Final Report)

This project focused on the development of multi-metallic layered composites (MMLCs) for advanced fission reactor technologies. There are many instances where one alloy or material simply cannot meet all the demands thrown at it by a reactor system, or cannot allow it to perform as strongly as one would like. Instead of focusing all our effort on developing one perfect alloy, we seek to leverage the design principle of “separation of functionality,” used in many other arenas in design, to boost performance beyond single alloys alone. One illustrative example shows the power of this approach for molten salt-cooled reactors: A three meter tall, three meter diameter reactor vessel made of Incoloy 800 was quoted at $\$$500k in 2018. A Hastelloy N vessel was quoted at $\$$5M. An MMLC vessel, in which a layer of Hastelloy N would be weld-overlaid onto Incoloy 800, was quoted at $\$$700k, and it would achieve the same performance. The potential economic gains of leveraging this approach are therefore substantial. At a minimum, each MMLC would contain one core structural layer and one coolant-facing corrosion-resistant layer. Sometimes, MMLCs required buffer layers, as the structural and corrosion-resistant layers were metallurgically incompatible. In other words, they didn’t always play nice, thus separating layers compatible with both functioned as intermediaries to keep the composite together. However, in doing so we inevitably produce new interfaces, where new issues can arise. Therefore, this project focused on what happens at these interfaces from a combination of high temperatures, irradiation, corrosion, and time. After all, a reactor makes money when it is operating, and outages of any kind erode its economic viability. First, we set out to experimentally prove that MMLCs for at least two advanced reactor systems can be made, today, in US domestic facilities. In this respect we were successful – one MMLC (a Ni-201/Incoloy 800H composite) was successfully made and drawn into two-inch coolant piping. Others were attempted, though new issues relating to cracking in vanadium layers for one and radiation damage performance of the corrosion-resistant layer in another prevented us from moving further in those specific arenas – these are engineering problems which deserve continued focus after this project. Additional experimental work focused on long-term corrosion testing of the outermost layers of the salt-cooled and liquid lead-cooled MMLC concepts, which would then be fed into predictions of how long the MMLCs could last. Next, computational (thermodynamics and atomistic) simulation studies studied how much we expect the interfaces to “blend,” due to the mixing action of neutron irradiation. This eats into both the margin for the structural layer of each MMLC, as dilution from the corrosion-resistant layer into the structural layer would decrease the total load-bearing capacity of an MMLC of finite size. On the other hand, dilution of the corrosion-resistant layer into the structural layer further reduced the margin of corrodible material, reducing the lifetime of the MMLC or necessitating extra thickness to be imparted to the MMLC to meet its functional requirements. Work here focused on irradiation-induced segregation to predict new phases which may embrittle the MMLCs, as well as quantifying irradiation-induced mixing at each interface. The results showed that mixing is expected, but it is both steady and therefore predictable, and not lifetime-limiting for most MMLC concepts – it simply has to be accounted for in calculations of reactor performance when utilizing an MMLC. Then, full-core simulations using the experimentally-derived corrosion data, the computationally discovered irradiation-induced mixing data (partially validated by experiment), and existing, benchmarked core designs for large and small sized reactor concepts (one salt-cooled, one lead-cooled) were conducted to quantify any expansion of reactor operating envelopes achieved by utilizing these MMLCs. This new framework, called REX (Reactor Envelope Expansion), incorporates a combination of core neutronics, thermal hydraulics, and the material performance data derived from this project to see how using an MMLC expands advanced fission reactor operating envelopes. It was discovered that in some cases, MMLC utilization does indeed increase the maximum operating temperatures and cycle lengths of reactor concepts, while in other cases it does not. Finally, our tech-to-market (T2M) strategy was not necessarily to create specific embodiments of MMLCs for immediate sale (because getting into the nuclear market is incredibly slow and laden with regulation, this is a long-term goal), but rather immediate stimulation of US industry using the design approach of MMLCs derived from this project. In this respect we were successful, as one of the PhD students funded on this project co-founded Allium Engineering, Inc., which created a stainless steel / low-alloy steel MMLC to function as chloride corrosion-resistant rebar for embedding into concrete structures. Allium Engineering continues to be successful, having recently opened their first factory as of this writing.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Direct ink write multi-material printing of PDMS-BTO composites with MWCNT electrodes for flexible force sensors

Here, with recent advances of additive manufacturing technology, direct ink write (DIW) printing has allowed to incorporate multi-material printing of various materials with freedom of design and complex geometric shapes to complete functional sensors in a one-step fabrication. This paper introduces the use of DIW 3D printing of polydimethylsiloxane (PDMS) with barium titanate (BTO) filler as stretchable composites with tunable piezoelectric properties that can be used for force sensors applications. To improve the bonding between stretchable piezoelectric composites and electrodes, multi-walled carbon nanotubes was included in the fabrication of electrodes at a fixed ratio of 11 wt. %. The alignment of the BTO dipoles was achieved through corona poling method, which applies an electric charge on the surface layer of the functional material, aligning the dipoles in the desired direction and thus gaining the piezoelectricity. Different BTO mixing ratios (10–50 wt. %) were evaluated in order to obtain tunable piezoelectric properties and compare the sensitivity with respect their elastic properties. Tensile testing and piezoelectric testing were carried out to characterize mechanical and piezoelectric properties. Results showed that fabricated PDMS with 50 wt. % BTO gave the highest piezoelectric coefficient (d 33 ) of 11.5 pC N -1 and with an output voltage of 385 mV under compression loading of >200 lbF. This demonstrates feasibility of using multi-material DIW printing to fabricate piezoelectric force sensors with integrated electrodes in one-step without compromising the flexibility of the material.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Bamboo Bio-composite Truck/Trailer Decking

Bamboo is one of the fastest growing plants in the world. Massively productive, bamboo will maintain that productivity with limited inputs and minimal management resulting in predictable volume and operating margins and with low overhead. The goal of this project was to develop a bamboo bio-composite trailer decking product that replaces apitong, is lighter weight, stronger and luminescent. The collaboration partners, Fontaine, Resource Fiber and IACMI, worked closely to develop the bamboo bio-composite decking to Fontaine Trailer’s (end-user) specifications. The various technological objectives were (a) To conduct a comprehensive Design of Experiments study for bamboo composites to understand the structure-property relationships for different resin composites and bamboo forms (strips, woven, bulk etc); (b) To establish the nail pull out characteristics of trailer deck geometry bamboo composite form. The nail pull out is a critical test in trailer decks; (c) To design, process and prototype select number of trailer decking planks for Fontaine evaluation; and (d) To conduct life cycle analysis to conduct energy calculations from the various conversion steps of the bamboo from crop to product. The project meets DOE/IACMI metrics of reduced embodied energy, lightweighting and lowering the cost of the end product. It also offers a green solution to a value-added application, i.e. trailer decking. The development goals and benefits of bamboo composite decking included: A. Decreased weight when compared to Apitong and Gen 1, thereby reducing operating costs and petroleum usage due to increased miles per gallon. B. Flexibility to allow camber design into trailers. C. Luminescence to increase safety during low light and dark conditions. D. Composite material to maximize use of bamboo bio-composites as substitute for petroleum-based composites. E. Embedded layer(s) of conditioned bamboo for added strength and stability. F. Improved safety over Apitong by temporary cargo indentation in planks for better stability. G. Cradle-to-cradle design so end-of-life becomes beginning-of-life for other products. Resource Fiber’s bamboo biocomposite trailer decking passed nail pullout tests as compared to apitong (incumbent), was lighter weight than apitong, and used less embodied energy particularly when bamboo is sourced domestically. The planks were optimized in the lab setting to the extent possible and successfully installed on the trailer at Fontaine for field testing. Despite the process not being fully optimized due to through-heat and tooling limitations within the budget constraints, the prototype decking withstood 400 cycles of reverse fatigue loading of a 107,000 lb Caterpillar 349F which was extreme conditions of field testing by Fontaine Trailer. Resource Fiber plans to outsource production of a next round of planks with a commercial pultrusion processor, then to do a re-test with Fontaine Trailers. Tooling specific to the part is required. Long-term commercial plans are to continue outsourcing production while supplying bamboo fiber and mats. Commercial markets include heavy haul trailers, military trailers, and decking for marine, industrial and residential use.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Impact of Lithium‐Free Borate Additives on the Cycle Life and Calendar Aging of Silicon‐Based Lithium‐Ion Batteries

Silicon-anode lithium-ion batteries (LIBs) suffer from limited cycle life and poor calendar life, constraining their large-scale commercialization. Integrating additives into electrolytes is a simple and cost-effective strategy to improve these aspects. The effects of lithium-free boron-based additives on cycling and calendar performance of high-loading Si-anode LIBs remain largely unexplored. In this work, the influence of five Li-free borate additives, each with distinct molecular structures and elemental compositions, is systematically investigated. All additives enhance cycle life to varying extents. Notably, the addition of 1 v/v% tri(2,2,2-trifluoroethyl) borate to the baseline electrolyte nearly doubles the cycle life at 50% state of health. This enhancement is attributed to three key factors. Specifically, borate additives 1) improve electrochemical activity, 2) act as anion receptors that interact with [PF6]- anions and carbonate solvents to reduce electrolyte decomposition, and 3) promote the formation of a stable and polymeric solid electrolyte interphase layer. Furthermore, these additives exhibited negligible impact in mitigating leakage current during a 180 h voltage-hold calendar-aging test, indicating their limited effect in calendar life. These findings provide insight into the role of Li-free borate additives in improving cycle life while addressing the knowledge gap regarding their influence on calendar aging.

Li, Defu↗
DOE OSTI2025

Corrosion Testing of Refractory inContact with Molten Glasses Designed for Waste Vitrification - VSL Touchpoint Matrix Glasses

It is known that the predictive life of the refractory ceramic liner of nuclear waste glass melters is conservative, as demonstrated by performance of these materials such as in the Defense Waste Processing Facility (DWPF). The motivation for this task is to maximize the useful life of the melters that will be operated at the Waste Treatment and Immobilization Plant (WTP), which will in turn minimize procurement and disposal costs and melter outage times, as well as to identify maximum loadings in the waste glass of those species that corrode melter components. This task was initiated jointly with Pacific Northwest National Laboratory (PNNL) with the objective to develop a methodology and model to enable more accurate prediction of refractory service life under prototypic conditions from laboratory-scale material corrosion tests. Refractory corrosion is generally reported as physical material loss, measured in units of distance (e.g., inch) or as physical material loss rate, measured in units of distance per time (e.g., inch/day). In post-operational melters, the refractory corrosion is measured directly, sometimes reported as corrosion depth. Crucible tests are used in the laboratory to accelerate the refractory corrosion to facilitate a meaningful measurement in a commensurate amount of time. Crucible tests are particularly useful in understanding refractory corrosion across a large glass composition space, where operational testing would be prohibitive. Some of the critical parameters that are known to influence refractory corrosion by molten glass in a crucible test are temperature, system redox, molten salt phases, glass chemistry, and test duration. The majority of data collected for Monofrax® K-3 (hereafter referred to as K-3) corrosion is from crucible tests, but a small amount comes directly from scaled and production melters. Crucible test data has been collected under varying conditions, whereas data collected from operational melters is relatively fewer and represents conditions specific to the melter campaign. The result is that the published data can be grouped and analyzed in multiple ways, not all of which are readily comparable. The Standard Test Method for Isothermal Corrosion Resistance of Refractories to Molten Glass (ASTM C621) outlines the general guidelines used across industry. That method describes a sealed, static test in which the surface area of the refractory coupon and the volume of glass are fixed. A significant portion of the crucible data pertaining to nuclear waste glasses has been collected in a modified configuration; the most notable differences being the surface area of the refractory coupon to volume of the glass and use of a method for bubbling the melt. To our knowledge, the influence of those parameters on the refractory corrosion has not been quantified. In this work, it was determined that static tests and bubbled tests would be performed. Savannah River National Laboratory (SRNL) was tasked with setting up and performing static testing while PNNL was tasked with setting up and performing bubbled testing. Initial activities were performed to establish laboratory methods that reproduce data comparable to existing data sets of K-3 refractory corrosion by low activity waste (LAW) and high-level waste (HLW) glass compositions. Later activities were focused on refining the test parameters to establish a standard test practice to be used between Laboratories and collecting additional data to be used in the enhanced waste glass model development. This document serves primarily to convey the refractory loss measurement results from corrosion testing of K-3 refractory with waste glass compositions developed for use in the WTP melters. The data will be used in the enhanced property/composition models being developed for waste glass vitrification and melter operations.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

FY23 Update: Aerosol Sampling for the Canister Deposition Field Demonstration

This report describes the results of preliminary testing of aerosol monitoring equipment that will be used to continuously monitor the aerosol source term for the multi-year Canister Deposition Field Demonstration (CDFD). These data are required inputs for the development and validation of models for the deposition of dust and potentially corrosive salts on the surface of spent nuclear fuel (SNF) dry storage canisters. Surface salt loads correlate with the extent of corrosion damage on a metal surface, and potentially to the likelihood and timing of initiation of stress corrosion cracks. Aerosols will be monitored at the CDFD site using three instruments. A Dekati ® ELPI+ cascade impactor will be used for real-time monitoring of aerosol particle sizes. It will also collect dust in 14 size bins on impactor targets that can be chemically analyzed to determine the soluble salts present as a function of particle size. However, this instrument can only measure dried aerosols, with a diameter of <10 µm. The second instrument is a Topas laser particle size spectrometer, which provides real-time monitoring of aerosol particle sizes up to ~40 µm in size. It monitors both the ambient (potentially deliquesced) aerosol particle size distributions required for the dust deposition models and the distributions of the equivalent dried particles, allowing correlation with the Dekati ® data. However, it does not discriminate between inert dust particles and salt aerosols, and it does not retain samples of the different particle sizes for later analysis. The third instrument that will monitor aerosols at the CDFD site is a Clean Air Status and Trends Network (CASTNET) tower, which uses a multiple canister system to collect weekly samples for analysis to total suspended aerosol particle compositions and atmospheric gas concentrations. This status report describes work in FY23 to develop the capabilities for using these tools. In two training exercises, the cascade impactor and laser particle sizer were deployed in two different testing environments, one indoor and one outdoor. For the cascade impactor, the tests provided opportunities for the operators to familiarize themselves with impactor substrate preparation, and post-test sample removal and analysis. For the laser particle sizer, the tests were used to evaluate different instrument parameters, to determine the most appropriate settings for capturing transient events. Data and samples were collected for weeks to months for each test, and the results are presented here. In addition to the preliminary testing, contracts were developed with WSP Analytical Labs for sample preparation and analysis of the cascade impactor samples. The impactor tower from outdoor test was delivered to WSP and used to train the staff there in disassembly, sample extraction, sample analysis, and tower reassembly with new target substrates. These are tasks that WSP will be performing routinely for the CDFD project. The CASTNET system cannot be purchased or tested until an actual site has been selected for the CDFD test. Work for this FY has been restricted to preparation of contracts for purchasing the CASTNET tower, and for sample analysis, once the tower is in operation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗