SEARCH · Search NASA

Results for “Configuration”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

All sources NASA NTRS DOE OSTI

NASA NTRS1973

Simulator evaluation of the low-speed flying qualities of an experimental STOL configuration with an externally blown flap wing or an augmentor wing

The low-speed flying qualities of an experimental STOL configuration were evaluated by using a fixed-base six-degree-of-freedom simulation. The configuration had either an externally blown flap (EBF) wing or an augmentor wing (AW). The AW configuration was investigated with two tails, one sized for the AW configuration and a larger one sized for the EBF configuration. The emphasis of the study was on the 70-knot approach task. The stability and control characteristics were compared with existing criteria. Several control systems were investigated for the normal four-engine condition and for the engine-out transient condition. Minimum control and stall speeds were determined for both the three- and four-engine operation.

Powers, B. G.↗

NASA NTRS1973

Hypersonic aerodynamic characteristics of an all-body research aircraft configuration

An experimental investigation was conducted at Mach 6 to determine the hypersonic aerodynamic characteristics of an all-body, delta-planform, hypersonic research aircraft (HYFAC configuration). The aerodynamic characteristics were obtained at Reynolds numbers based on model length of 2.84 million and 10.5 million and over an angle-of-attack range from minus 4 deg to 20 deg. The experimental results show that the HYFAC configuration is longitudinally stable and can be trimmed over the range of test conditions. The configuration had a small degree of directional stability over the angle-of-attack range and positive effective dihedral at angles of attack greater than 2 deg. Addition of canards caused a decrease in longitudinal stability and an increase in directional stability. Oil-flow studies revealed extensive areas of separated and vortex flow on the fuselage lee surface. A limited comparison of wind-tunnel data with several hypersonic approximations indicated that, except for the directional stability, the tangent-cone method gave adequate agreement at control settings between 5 deg and minus 5 deg and positive lift coefficient. A limited comparison indicated that the HYFAC configuration had greater longitudinal stability than an elliptical-cross-section configuration, but a lower maximum lift-drag ratio.

Clark, L. E.↗

NASA NTRS1974

Results of an experimental aerodynamic investigation to obtain static stability and control characteristics of the SSV configurations: The 2A(VL70-000089B) model 1 and 3(VL70-000139B) model 2 orbiter at Mach numbers of 2.5, 3.9 and 4.6 in the NASA LaRC 4 X 4-foot UPWT (OA44)

Investigation of space shuttle orbiter configurations 2A(VL70-000089B) and 3(VL70-000139B) was performed at the Langley Research Center Unitary Plan Wind Tunnel (UPWT) from June 1, 1973, to June 15, 1973, for 60 test hours. The primary test objectives were to obtain stability and control characteristics for Configurations 2A and 3 and an alternate forebody used with Configuration 3. In addition, hinge moments were measured on the elevons and rudder for Configuration 2A only. The configurations were tested at Mach numbers 2.5, 3.9 and 4.6. Pitch runs were made at angles of attack from -4 to 44 deg and sideslip angles from -4 to +6. Static pressures were measured at the fuselage base for use in force data correction.

Esparza, V.↗

NASA NTRS1975

Effect of vertical-tail location on the aerodynamic characteristics at subsonic speeds of a close-coupled canard configuration

The effects were studied of various vertical-tail configurations on the longitudinal and lateral directional-stability characteristics of a general research fighter model utilizing wing-body-canard. The study indicates that the addition of the high canard resulted in an increase in total lift at angles of attack above 4 deg with a maximum lift coefficient about twice as large as that for the wing-body configuration. For the wing-body (canard off) configuration, the center-line vertical tail indicates positive vertical-tail effectiveness throughout the test angle-of-attack range; however, for this configuration none of the wing-mounted vertical-tail locations tested resulted in a positive directional-stability increment at the higher angles of attack. For the wing-body-canard configuration several outboard locations of the wing-mounted vertical tails were found.

Huffman, J. K.↗

NASA NTRS1976

Effects of four inlet and outlet tip-annulus-area blockage configurations on the performance of an axial-flow fan rotor

An axial-flow fan rotor was tested with four configurations of tip-annulus-area blockage to speeds as high as 0.8 of design speed. The rotor performance with the four blockage configurations is compared with the unblocked rotor performance and with blockage configurations previously investigated. The blockage configurations enable the rotor to operate in a stable condition, to much lower flows than the unblocked rotor, with no evidence of rotating stall. The blockage configurations were effective in reducing rotor torque and weight flow but were accompanied by reductions in pressure ratio and efficiency.

Osborn, W. M.↗

NASA NTRS1978

Analytical study of ride smoothing benefits of control system configurations optimized for pilot handling qualities

An analytical study was conducted to evaluate the relative improvements in aircraft ride qualities that resulted from utilizing several control law configurations that were optimized for pilot handling qualities only. The airplane configuration used was an executive jet transport in the approach configuration. The control law configurations included the basic system, a rate feedback system, three command augmentation systems (rate command, attitude command, and rate command/attitude hold), and a control wheel steering system. Both the longitudinal and lateral directional axes were evaluated. A representative example of each control law configuration was optimized for pilot handling qualities on a fixed base simulator. The root mean square airplane responses to turbulence were calculated, and predictions of ride quality ratings were computed by using three models available in the literature.

Powers, B. G.↗

NASA NTRS1978

Effects of wing leading-edge flap deflections on subsonic longitudinal aerodynamic characteristics of a wing-fuselage configuration with a 44 deg swept wing

An investigation was conducted to determine the effects of wing leading-edge flap deflections on the subsonic longitudinal aerodynamic characteristics of a wing-fuselage configuration with a 44 deg swept wing. The tests were conducted at Mach numbers from 0.40 to 0.85, corresponding to Reynolds numbers (based on wing mean geometric chord) of 2.37 x 1,000,000 to 4.59 x 1,000,000 and at angles of attack from -3 deg to 22 deg. The configurations under study included a wing-fuselage configuration and a wing-fuselage-strake configuration. Each configuration had multisegmented, constant-chord leading-edge flaps which could be deflected independently or in various combinations.

Henderson, W. P.↗

NASA NTRS1979

Transition aerodynamics for close-coupled wing-canard configuration

A series of wind-tunnel tests have been conducted in the Langley V/STOL tunnel to investigate the low-speed longitudinal aerodynamics of two powered close-coupled wing-canard fighter configurations. A brief review is provided of the high angle-of-attack data for the two wing-canard configurations tested showing the benefits and problem areas of powered lift. A takeoff and landing analysis is presented which defines the area in which a fighter-type aircraft must operate in order to achieve 305-m field lengths. The wing-canard configuration data are analyzed in detail showing the problems of obtaining high lift, high drag, and trimmed moments. Assuming that power will be used to trim the aircraft, data are presented comparing the transition aerodynamics of the wing-canard configuration using a nose jet with several V/STOL configurations.

Paulson, J. W., Jr.↗

NASA NTRS1980

Grid generation for general three-dimensional configurations

A suitable grid system for complex three dimensional configurations such as wing/body/nacelle shape for the solution of nonlinear transonic flow problems was constructed. Two approaches were explored based on Thompson's body fitted coordinate concept. The most general approach was to divide the computational domain into multiple rectangular blocks where the configuration itself was also represented by a set of blocks whose structure follows the natural lines of the configuration. The block structured grid system was adaptable to complex configurations and gives good grid quality near physical corners. However, it introduced algorithm issues for the flow solution concerning the treatment of nonanalytic grid block boundaries and nonstandard grid cells. These issues were explored in relation to the grid generation. A more limited approach treats a wing/body configuration with only a single rectangular block in computational space. The issues involving nonstandard cells were avoided, but other limitations on grid resolution appear. Both a linear and a nonlinear system of grid generation equations were developed including methods of grid control.

Lee, K. D.↗

NASA NTRS1980

Effects of angle of attack and vertical fin on transonic flutter characteristics of an arrow-wing configuration

Experimental transonic flutter results are presented for a simplified 1/50 size, aspect ratio 1.77, wind tunnel model of an arrow wing design. Flutter results are presented for two configurations; namely, one with and one without a ventral fin mounted at the 0.694 semispan station. Results are presented for both configurations trimmed to zero lift and in a lifting condition at angles of attack up to 4 deg. The results show that the flutter characteristics of both configurations are similar to those usually observed. Increasing angle of attack reduces the flutter dynamic pressure by a small amount (about 13 percent maximum) for both configurations. The addition of the fin to the basic wing increases the flutter dynamic pressure. Calculated results for both configurations in the nonlifting condition obtained by using subsonic doublet lattice unsteady aerodynamic theory correlate reasonably well with the experimental results. Calculated results for the basic wing obtained by using subsonic kernal function unsteady aerodynamic theory did not agree as well with the experimental data.

Doggett, R. V., Jr.↗

NASA NTRS1980

Integrative application of active controls (IAAC) technology to an advanced subsonic transport project. Initial act configuration design study

The performance and economic benefits of a constrained application of Active Controls Technology (ACT) are identified, and the approach to airplane design is established for subsequent steps leading to the development of a less constrained final ACT configuration. The active controls configurations are measured against a conventional baseline configuration, a state-of-the-art transport, to determine whether the performance and economic changes resulting from ACT merit proceeding with the project. The technology established by the conventional baseline configuration was held constant except for the addition of ACT. The wing, with the same planform, was moved forward on the initial ACT configuration to move the loading range aft relative to the wing mean aerodynamic chord. Wing trailing-edge surfaces and surface controls also were reconfigured for load alleviation and structural stabilization.

Source record↗

NASA NTRS1984

Low-speed wind-tunnel study of the high-angle-of-attack stability and control characteristics of a cranked-arrow-wing fighter configuration

The low-speed, high-angle-of-attack stability and control characteristics of a fighter configuration incorporating a cranked arrow wing were investigated in the Langley 30- by 60-foot tunnel as part of a NASA/General Dynamics cooperative research program to investigate the application of advanced wing designs to combat aircraft. Tests were conducted on a baseline configuration and on several modified configurations. The results show that the baseline configuration exhibited a high level of maximum lift but displayed undesirable longitudinal and lateral-directional stability characteristics at high angles of attack. Various wing modifications were made which improved the longitudinal and lateral-directional stability characteristics of the configuration at high angles of attack. However, most of the modifications were detrimental to maximum lift.

Grafton, S. B.↗

NASA NTRS1984

Validation of a transonic analysis code for use in preliminary design of advanced transport configurations

The WBPPW code has the capability of analyzing flow-field effects about configurations which include wing pylons and engine nacelles or pods in addition to the basic wing/fuselage combination. Using the concept of grid embedding, the code solves the extended small disturbance transonic flow equation for complex flow interactions of the various configuration components. A general description of the code and solution algorithm is included. Results are presented and compared with experiment for various configurations which encompass the code capabilities. These include wing planform and wing contour modifications and variations in nacelle position beneath a high-aspect-ratio wing. Results are analyzed in the light of preliminary design, where the capability to accurately compute flow-field effects resulting from various configuration perturbations is important. The comparisons show that the computational results are sensitive to subtle design modifications and that the code could be used as an effective guide during the design process for transport configurations.

Waggoner, E. G.↗

NASA NTRS1986

Application of a linearized unsteady aerodynamic analysis to standard cascade configurations

A linearized potential flow analysis, which accounts for the effects of nonuniform steady flow phenomena on the linearized unsteady aerodynamic response to prescribed blade motions, has been applied to five cascade configurations. These include the first, fifth, eighth and ninth standard configurations proposed as a result of the Second International Symposium on Aeroelasticity in Turbomachines and a NASA Lewis flutter cascade. Selected results from this study, including comparisons between analytical predictions and the experimental measurements submitted for three of the foregoing configurations, are described. The correlation between theory and experiment for the first standard configuration (a compressor cascade operating at low Mach number and frequency) is quite good. Moreover, the predictions and measurements for the NASA Lewis cascade of symmetric biconvex airfoils show good qualitative agreement. However, wide discrepancies exist between the theoretical predictions and the experimental measurements for the fifth standard configuration (a subsonic transonic fan tip cascade). These can be partially attributed to conditions being imposed in the experiment which differ from those commonly used in unsteady aerodynamic analyses.

Verdon, J. M.↗

NASA NTRS1986

An experimental study of the lift, drag and static longitudinal stability for a three lifting surface configuration

The experimental procedure and aerodynamic force and moment measurements for wind tunnel testing of the three lifting surface configuration (TLC) are described. The influence of nonelliptical lift distributions on lift, drag, and static longitudinal stability are examined; graphs of the lift coefficient versus angle of attack, the pitching moment coefficient, drag coefficient, and lift to drag ratio versus lift coefficient are provided. The TLC data are compared with the conventional tail-aft configuration and the canard-wing configuration; it is concluded that the TLC has better lift and high-lift drag characteristics, lift to drag ratio, and zero-lift moments than the other two configurations. The effects of variations in forward and tail wind incidence angles, gap, stagger, and forward wind span on the drag, lift, longitudinal stability, and zero-lift moments of the configuration are studied.

Ostowari, C.↗

NASA NTRS1987

Subsonic longitudinal and lateral-directional characteristics of a forward-swept-wing fighter configuration at angles of attack up to 47 deg

Subsonic lateral-direction and longitudinal characteristics of a forward-swept-wing fighter configuration were examined in wind-tunnel tests at Mach numbers of 0.2 and 0.5 for angles of attack from -7 to 47 deg. and over a sidelslip range of +/- 15 deg. The effects of a canard, strakes, vertical tail, and leading- and trailing-edge flaps are examined. The canard and strakes both reduce asymmetric moments and side forces at zero sideslip for angles of attack up to about 30 deg. The canard has a small influence on lateral-directional stability; however, strakes produce a substantial reduction in lateral stability for angles of attack greater than about 20 deg. The vertical tail improves directional stability for angles of attack up to 30 deg. Deflection of the leading-edge flap to 20 deg. at high angles of attack on the strake and canard configurations degrades lateral and directional stability. Deflection of the trailing-edge flap to 20 deg. on the canard configuration generally increases lateral and directional stability at high angles of attack. Leading- and trailing-edge flaps on the wing-body and canard configurations are effective for increased lift only for angles of attack up to about 40 deg. The leading-edge flap remains effective on the strake configuration over the entire angle-of-attack range tested.

Mann, Michael J.↗

NASA NTRS1987

Low-speed aerodynamic characteristics of a twin-engine general aviation configuration with aft-fuselage-mounted pusher propellers

An investigation was conducted to determine the aerodynamic characteristics of an advanced turboprop aircraft model with aft-pylon-mounted pusher propellers. Tests were conducted through an angle-of-attack range of -8 to 28 degrees, and an angle-of-sideslip range of -20 to 20 degrees at free-stream conditions corresponding to Reynolds numbers of 0.55 to 2.14 x 10 to the 6th power based on mean aerodynamic chord. Test results show that for the unpowered configurations the maximum lift coefficients for the cruise, takeoff, and landing configurations are 1.45, 1.90, and 2.10, respectively. Nacelle installation results in a drag coefficient increase of 0.01. Increasing propeller thrust results in a significant increase in lift for angles of attack above stall and improves the longitudinal stability. The cruise configuration remains longitudinally stable to an angle of attack 5 degrees beyond the stall angle, the takeoff configuration is stable 4 degrees beyond stall angle, and the landing configuration is stable 3 degrees beyond stall angle. The predominant effect of symmetric thrust on the lateral-directional aerodynamic characteristics is in the post-stall region, where additional rudder control is available with power on.

Dunham, Dana Morris↗

NASA NTRS1986

Exploratory wind-tunnel investigation of the stability and control characteristics of advanced general aviation configurations

Results of low-speed wind-tunnel investigations are presented for two general aviation configurations: the AVTEK canard configuration and the DeVore conventional configuration. Cooperative research programs were undertaken by industry and NASA to jointly conduct tests in the NASA Langley 12-Foot Low-Speed Wind Tunnel to explore stability and control characteristics of each configuration. A 1/5-scale AVTEK model and a 1/6-scale DeVore model were tested over an angle-of-attack range of up to 45 deg and an angle-of-sideslip range of up to 20 deg. Results from the AVTEK test are presented with an emphasis on the effects of configuration on the stall and poststall characteristics. Results from the DeVore test are presented with emphasis on the effects of wing leading-edge droop design on spin resistance characteristics.

Yip, L. P.↗