Search NASA⌕ Search

SEARCH · Search NASA

Results for “Control Model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

Experimental modification and identification of the DSS-13 antenna control system model

This work is the first step toward increasing the bandwidth of the DSS-13 antenna position loop controller. A wider bandwidth of the controller allows for faster tracking rates and better pointing performance under windy conditions. To achieve this goal, the antenna control system model has to be improved, such that it will accurately reflect the dynamic properties of the antenna. The existing analytical model, due to its many uncertainties, could not be used in the design of the controller. However, by using experimental data, the analytical model is modified and improved, and a new model is obtained through system identification techniques.

Racho, C. S.↗

Study report on guidelines and test procedures for investigating stability of nonlinear cardiovascular control system models

A general study of the stability of nonlinear as compared to linear control systems is presented. The analysis is general and, therefore, applies to other types of nonlinear biological control systems as well as the cardiovascular control system models. Both inherent and numerical stability are discussed for corresponding analytical and graphic methods and numerical methods.

Fitzjerrell, D. G.↗

Intelligent sensor-model automated control of PMR-15 autoclave processing

An intelligent sensor model system has been built and used for automated control of the PMR-15 cure process in the autoclave. The system uses frequency-dependent FM sensing (FDEMS), the Loos processing model, and the Air Force QPAL intelligent software shell. The Loos model is used to predict and optimize the cure process including the time-temperature dependence of the extent of reaction, flow, and part consolidation. The FDEMS sensing system in turn monitors, in situ, the removal of solvent, changes in the viscosity, reaction advancement and cure completion in the mold continuously throughout the processing cycle. The sensor information is compared with the optimum processing conditions from the model. The QPAL composite cure control system allows comparison of the sensor monitoring with the model predictions to be broken down into a series of discrete steps and provides a language for making decisions on what to do next regarding time-temperature and pressure.

Hart, S.↗

Passive heat transfer control

Model maintains a preselected temperature in the near vicinity of a variable source of thermal energy. Heat input is controlled by a variable transformer and a voltage drop across the heater is used to calculate power dissipated.

Fitz, F. A.↗

An airfoil pitch apparatus-modeling and control design

The study of dynamic stall of rapidly pitching airfoils is being conducted at NASA Ames Research Center. Understanding this physical phenomenon will aid in improving the maneuverability of fighter aircraft as well as civilian aircraft. A wind tunnel device which can linearly pitch and control an airfoil with rapid dynamic response is needed for such tests. To develop a mechanism capable of high accelerations, an accurate model and control system is created. The model contains mathematical representations of the mechanical system, including mass, spring, and damping characteristics for each structural element, as well as coulomb friction and servovalve saturation. Electrical components, both digital and analog, linear and nonlinear, are simulated. The implementation of such a high-performance system requires detailed control design as well as state-of-the-art components. This paper describes the system model, states the system requirements, and presents results of its theoretical performance which maximizes the structural and hydraulic aspects of this system.

Andrews, Daniel R.↗

An airfoil pitch apparatus-modeling and control design

The study of dynamic stall of rapidly pitching airfoils is being conducted at NASA Ames Research Center. Understanding this physical phenomenon will aid in improving the maneuverability of fighter aircraft as well as civilian aircraft. A wind tunnel device which can linearly pitch and control an airfoil with rapid dynamic reponse is needed for such tests. To develop a mechanism capable of high accelerations, an accurate model and control system is created. The model contains mathematical representations of the mechanical system, including mass, spring, and damping characteristics for each structural element, as well as coulomb friction and servovalve saturation. Electrical components, both digital and analog, linear and nonlinear, are simulated. The implementation of such a high-performance system requires detailed control design as well as state-of-the-art components. This paper describes the system model, states the system requirements, and presents results of its theoretical performance which maximizes the structural and hydraulic aspects of this system.

Andrews, Daniel R.↗

NASA Langley Distributed Propulsion VTOL Tilt-Wing Aircraft Testing, Modeling, Simulation, Control, and Flight Test Development

Control of complex Vertical Take-Off and Landing (VTOL) aircraft traversing from hovering to wing born flight mode and back poses notoriously difficult modeling, simulation, control, and flight-testing challenges. This paper provides an overview of the techniques and advances required to develop the GL-10 tilt-wing, tilt-tail, long endurance, VTOL aircraft control system. The GL-10 prototype's unusual and complex configuration requires application of state-of-the-art techniques and some significant advances in wind tunnel infrastructure automation, efficient Design Of Experiments (DOE) tunnel test techniques, modeling, multi-body equations of motion, multi-body actuator models, simulation, control algorithm design, and flight test avionics, testing, and analysis. The following compendium surveys key disciplines required to develop an effective control system for this challenging vehicle in this on-going effort.

Rothhaar, Paul M.↗

Utilizing Chamber Data for Developing and Validating Climate Change Models

Controlled environment chambers (e.g. growth chambers, SPAR chambers, or open-top chambers) are useful for measuring plant ecosystem responses to climatic variables and CO2 that affect plant water relations. However, data from chambers was found to overestimate responses of C fluxes to CO2 enrichment. Chamber data may be confounded by numerous artifacts (e.g. sidelighting, edge effects, increased temperature and VPD, etc) and this limits what can be measured accurately. Chambers can be used to measure canopy level energy balance under controlled conditions and plant transpiration responses to CO2 concentration can be elucidated. However, these measurements cannot be used directly in model development or validation. The response of stomatal conductance to CO2 will be the same as in the field, but the measured response must be recalculated in such a manner to account for differences in aerodynamic conductance, temperature and VPD between the chamber and the field.

Monje, Oscar↗

Dynamic modeling and control of multibody mechanical systems which are structurally flexible

This paper concerns the dynamic modeling and control of multibody, open-chained, structurally flexible, mechanical systems where the bodies are connected by revolute joints. The equations of motion are formulated based on a matrix form of Lagrange's equations for inertial quasi-coordinates. Each body is treated as a substructure of the system. For the purposes of simulation and control, the equations of motion are separated into two sets of equations using a perturbation approach: one to describe large rigid-body motions of the articulated system and the other to describe small linear motions of the bodies about the large motions. A biologically natural control strategy is used for vibration suppression and tracking the prescribed motion.

Quinn, R. D.↗

Road load simulator tests of the Gould phase 1 functional model silicon controlled rectifier ac motor controller for electric vehicles

The test results for a functional model ac motor controller for electric vehicles and a three-phase induction motor which were dynamically tested on the Lewis Research Center road load simulator are presented. Results show that the controller has the capability to meet the SAE-J227a D cycle test schedule and to accelerate a 1576-kg (3456-lb) simulated vehicle to a cruise speed of 88.5 km/hr (55 mph). Combined motor controller efficiency is 72 percent and the power inverter efficiency alone is 89 percent for the cruise region of the D cycle. Steady state test results for motoring, regeneration, and thermal data obtained by operating the simulator as a conventional dynamometer are in agreement with the contractor's previously reported data. The regeneration test results indicate that a reduction in energy requirements for urban driving cycles is attainable with regenerative braking. Test results and data in this report serve as a data base for further development of ac motor controllers and propulsion systems for electric vehicles. The controller uses state-of-the-art silicon controlled rectifier (SCR) power semiconductors and microprocessor-based logic and control circuitry. The controller was developed by Gould Laboratories under a Lewis contract for the Department of Energy's Electric and Hybrid Vehicle program.

Gourash, F.↗

Model Predictive Control Study for an Electrified Turbofan Engine

A control sensitivity study is conducted for electrified aircraft propulsion concepts using a publicly available turbofan engine simulation. A Proportional-Integral (PI) controller serves as a baseline for comparison against an advanced Model Predictive Control (MPC) approach. MPC is used in the control scheme to allow for subsystem coordination of engine and electric power loads. The electrified turbofan engine includes electric machines to augment the amount of torque being applied to the spools of the engine during transient phases of operation. Power augmentation allows for energy to be stored or exhausted in a manner that increases the fuel efficiency of the engine, reducing aircraft emissions and noise. The study compares the fan speed, high pressure compressor stall margin, and low pressure compressor stall margin against the baseline PI control system, an MPC system without electric machines, and an MPC system with electric machines. The MPC system with electric machines is optimized using the sample time, control horizon and prediction horizon. The MPC design provided a stable damped response as desired and allowed operability margins to be maintained

Electrified Aircraft Propulsion↗

LPV Modeling and Control for Active Flutter Suppression of a Smart Airfoil

In this paper, a novel technique of linear parameter varying (LPV) modeling and control of a smart airfoil for active flutter suppression is proposed, where the smart airfoil has a groove along its chord and contains a moving mass that is used to control the airfoil pitching and plunging motions. The new LPV modeling technique is proposed that uses mass position as a scheduling parameter to describe the physical constraint of the moving mass, in addition the hard constraint at the boundaries is realized by proper selection of the parameter varying function. Therefore, the position of the moving mass and the free stream airspeed are considered the scheduling parameters in the study. A state-feedback based LPV gain-scheduling controller with guaranteed H infinity performance is presented by utilizing the dynamics of the moving mass as scheduling parameter at a given airspeed. The numerical simulations demonstrate the effectiveness of the proposed LPV control architecture by significantly improving the performance while reducing the control effort.

Smart Airfoil↗

Modeling and Control for a Flexible Inverted Pendulum Robot

This report describes the tasks accomplished during Fall 2020 at the Kennedy Space Center under the scope of the Robotic Control System Design internship project. These tasks primarily supported development of an augmented adaptive control system for an inverted pendulum (IP) robotic system on a 4-wheel mobile base (Penny). This system serves as an analogue to the control problems in the flight of rockets in the initial and latter stages of launch, and methods developed as part of this research can later be applied to more complex IP systems, such as launch vehicles. To more accurately model launch vehicles, a flexible aluminum pendulum is used both on the hardware and in the simulated models. In order to capture the flexible dynamics of the system, hardware modifications were made to Penny (including installation of a rate gyro at the tip of the pendulum). Simulink models were created to control and model the hardware system, and Simscape models were created/updated to model the system in simulation. MATLAB programs were created throughout the internship to analyze data generated from hardware and simulation runs. Linear fixed-gain controllers have been applied to the simulated and hardware system, and work continues with augmenting these controllers using sensor blending and direct output adaptive control methods to improve stabilization of system states and cancel flex dynamics. In addition to describing the work done to support these modeling efforts, an Independent Research and Technology Development (IR&TD) proposal for a lunar simulation with soil deformation modeling developed during the internship is briefly described.

Nashir A Janmohamed↗

Evaluation of optimal control type models for the human gunner in an Anti-Aircraft Artillery (AAA) system

The selection of the structure of optimal control type models for the human gunner in an anti aircraft artillery system is considered. Several structures within the LQG framework may be formulated. Two basic types are considered: (1) kth derivative controllers; and (2) proportional integral derivative (P-I-D) controllers. It is shown that a suitable criterion for model structure determination can be based on the ensemble statistics of the tracking error. In the case when the ensemble tracking steady state error is zero, it is suggested that a P-I-D controller formulation be used in preference to the kth derivative controller.

Phatak, A. V.↗

Partition-based Feasible Integer Solution Pre-computation for Hybrid Model Predictive Control

For multiparametric mixed-integer convex programming problems such as those encountered in hybrid model predictive control, we propose an algorithm for generating a feasible partition of a subset of the parameter space. The result is a static map from the current parameter to a suboptimal integer solution such that the remaining convex program is feasible. Convergence is proved with a new insight that the overlap among the feasible parameter sets of each integer solution governs the partition complexity. The partition is stored as a tree which makes querying the feasible solution efficient. The algorithm can be used to warm start a mixed integer solver with a real-time guarantee or to provide a reference integer solution in several suboptimal MPC schemes. The algorithm is tested on randomly generated systems with up to six states, demonstrating the effectiveness of the approach.

Bayard, David S.↗

An optimized rotation-axis model-following controller for STS orbiter attitude maneuvers

This paper describes a new controller for automatic attitude maneuvers of the Space Shuttle Orbiter. The controller incorporates a new solution algorithm for partially linearized, fuel-optimal maneuvers for RCS jet controlled spacecraft. These solutions provide model trajectories and jet commands that are easily tracked using a feed-forward, feedback controller structure. The result is a substantial performance improvement over the current Orbiter attitude maneuver controller. The paper discusses optimal maneuvers for this type of vehicle, giving detail of the solution algorithm. Closed-loop controller design and implementation is discussed. Detailed performance results are presented.

Redding, D. C.↗