Search NASA⌕ Search

SEARCH · Search NASA

Results for “DOORS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS2009

Use of UV Sources for Detection and Identification of Explosives

Measurement of Raman and native fluorescence emission using ultraviolet (UV) sources (<400 nm) on targeted materials is suitable for both sensitive detection and accurate identification of explosive materials. When the UV emission data are analyzed using a combination of Principal Component Analysis (PCA) and cluster analysis, chemicals and biological samples can be differentiated based on the geometric arrangement of molecules, the number of repeating aromatic rings, associated functional groups (nitrogen, sulfur, hydroxyl, and methyl), microbial life cycles (spores vs. vegetative cells), and the number of conjugated bonds. Explosive materials can be separated from one another as well as from a range of possible background materials, which includes microbes, car doors, motor oil, and fingerprints on car doors, etc. Many explosives are comprised of similar atomic constituents found in potential background samples such as fingerprint oils/skin, motor oil, and soil. This technique is sensitive to chemical bonds between the elements that lead to the discriminating separability between backgrounds and explosive materials.

Hug, William↗
NASA NTRS1951

Supplementary Free-Spinning-Tunnel Investigation of a 1/30-Scale Model of the Grumman XF10F-1 Airplane in the Swept-Wing Configuration with Slats Extended

A supplementary investigation has been conducted in the Langley 20-foot free-spinning tunnel of a 1/30 -scale model of the Grumman XFlOF-1 airplane to determine what effect full-span slats would have on the spin-recovery characteristics of the swept-wing version of the XFlOF-1 airplane, which had previously been indicated as possessing undesirable spin-recovery characteristics without slats. The effects of extended nose-wheel doors and of fairing the air-duct inlets were also determined. The results indicated that, with slats fully extended, satisfactory recovery could be obtained by rudder reversal provided it was accompanied by movement of the trimmer ailerons to full with the spin (only up-going spoiler operative), Extension of the nose-wheel doors or fairing of the air-duct inlets did not improve the recovery characteristics.

Berman, Theodore↗
NASA NTRS2010

Prediction of Landing Gear Noise Reduction and Comparison to Measurements

Noise continues to be an ongoing problem for existing aircraft in flight and is projected to be a concern for next generation designs. During landing, when the engines are operating at reduced power, the noise from the airframe, of which landing gear noise is an important part, is equal to the engine noise. There are several methods of predicting landing gear noise, but none have been applied to predict the change in noise due to a change in landing gear design. The current effort uses the Landing Gear Model and Acoustic Prediction (LGMAP) code, developed at The Pennsylvania State University to predict the noise from landing gear. These predictions include the influence of noise reduction concepts on the landing gear noise. LGMAP is compared to wind tunnel experiments of a 6.3%-scale Boeing 777 main gear performed in the Quiet Flow Facility (QFF) at NASA Langley. The geometries tested in the QFF include the landing gear with and without a toboggan fairing and the door. It is shown that LGMAP is able to predict the noise directives and spectra from the model-scale test for the baseline configuration as accurately as current gear prediction methods. However, LGMAP is also able to predict the difference in noise caused by the toboggan fairing and by removing the landing gear door. LGMAP is also compared to far-field ground-based flush-mounted microphone measurements from the 2005 Quiet Technology Demonstrator 2 (QTD 2) flight test. These comparisons include a Boeing 777-300ER with and without a toboggan fairing that demonstrate that LGMAP can be applied to full-scale flyover measurements. LGMAP predictions of the noise generated by the nose gear on the main gear measurements are also shown.

Lopes, Leonard V.↗
NASA NTRS2010

Orbital fabrication of aluminum foam and apparatus therefore

A process for producing foamed aluminum in space comprising the steps of: heating aluminum until it is molten; applying the force of gravity to the molten aluminum; injecting gas into the molten aluminum to produce molten foamed aluminum; and allowing the molten foamed aluminum to cool to below melting temperature. The apparatus for carrying out this invention comprises: a furnace which rotates to simulate the force of gravity and heats the aluminum until it is molten; a door on the furnace, which is opened for charging the aluminum into the furnace, closed for processing and opened again for removal of the foamed aluminum; a gas injection apparatus for injecting gas into the molten aluminum within the furnace; and an extraction apparatus adjacent the door for removing the foamed aluminum from the furnace.

Tucker, Dennis S.↗
NASA NTRS2010

Integration of the Electrodynamic Dust Shield on a Lunar Habitat Demonstration Unit

NASA is developing a Habitat Demonstration Unit (HDU) to investigate the feasibility of lunar surface technologies and lunar ground operations. The HDU will define and validate lunar scenario architecture through field analog testing. It will contain a four-port vertical habitat module with docking demonstration capabilities. The Electrodynamic Oust Shield (EDS) is being incorporated into the HDU to demonstrate dust removal from a viewport and from a door prior to docking procedures. In this paper, we will describe our efforts to scale up the EDS to protect a viewport 20 cm in diameter. We will also describe the development of several 20 cm x 25 cm EDS patches to demonstrate dust removal from one of the HDU doors.

Calle, C. I.↗
NASA NTRS2010

Apollo 11 Telemetry Data Recordings: A Final Report

When astronauts landed on the moon on July 20, 1969, the Eagle lander carried a small, unconventional television camera affixed to the inside of the door. It had one mission. Once astronauts opened the door and activated the camera, it would begin shooting live images of the historic event, transmitting the raw footage by way of an antenna to Earth below. There, engineers at three tracking stations would tape the original signals onto one-inch telemetry tapes fpr backup and then also convert the raw feed into a conventional format compatible with American broadcast standards.

Apollo 11↗
NASA NTRS2011

Teleoperated Marsupial Mobile Sensor Platform Pair for Telepresence Insertion Into Challenging Structures

A platform has been developed for two or more vehicles with one or more residing within the other (a marsupial pair). This configuration consists of a large, versatile robot that is carrying a smaller, more specialized autonomous operating robot(s) and/or mobile repeaters for extended transmission. The larger vehicle, which is equipped with a ramp and/or a robotic arm, is used to operate over a more challenging topography than the smaller one(s) that may have a more limited inspection area to traverse. The intended use of this concept is to facilitate the insertion of a small video camera and sensor platform into a difficult entry area. In a terrestrial application, this may be a bus or a subway car with narrow aisles or steep stairs. The first field-tested configuration is a tracked vehicle bearing a rigid ramp of fixed length and width. A smaller six-wheeled vehicle approximately 10 in. (25 cm) wide by 12 in. (30 cm) long resides at the end of the ramp within the larger vehicle. The ramp extends from the larger vehicle and is tipped up into the air. Using video feedback from a camera atop the larger robot, the operator at a remote location can steer the larger vehicle to the bus door. Once positioned at the door, the operator can switch video feedback to a camera at the end of the ramp to facilitate the mating of the end of the ramp to the top landing at the upper terminus of the steps. The ramp can be lowered by remote control until its end is in contact with the top landing. At the same time, the end of the ramp bearing the smaller vehicle is raised to minimize the angle of the slope the smaller vehicle has to climb, and further gives the operator a better view of the entry to the bus from the smaller vehicle. Control is passed over to the smaller vehicle and, using video feedback from the camera, it is driven up the ramp, turned oblique into the bus, and then sent down the aisle for surveillance. The demonstrated vehicle was used to scale the steps leading to the interior of a bus whose landing is 44 in. (.1.1 m) from the road surface. This vehicle can position the end of its ramp to a surface over 50 in. (.1.3 m) above ground level and can drive over rail heights exceeding 6 in. (.15 cm). Thus configured, this vehicle can conceivably deliver the smaller robot to the end platform of New York City subway cars from between the rails. This innovation is scalable to other formulations for size, mobility, and surveillance functions. Conceivably the larger vehicle can be configured to traverse unstable rubble and debris to transport a smaller search and rescue vehicle as close as possible to the scene of a disaster such as a collapsed building. The smaller vehicle, tethered or otherwise, and capable of penetrating and traversing within the confined spaces in the collapsed structure, can transport imaging and other sensors to look for victims or other targets.

Krasowski, Michael J.↗
NASA NTRS2012

JWST Lifting System

A document describes designing, building, testing, and certifying a customized crane (Lifting Device LD) with a strong back (cradle) to facilitate the installation of long wall panels and short door panels for the GHe phase of the James Webb Space Telescope (JWST). The LD controls are variable-frequency drive controls designed to be adjustable for very slow and very-short-distance movements throughout the installation. The LD has a lift beam with an electric actuator attached at the end. The actuator attaches to a rectangular strong back (cradle) for lifting the long wall panels and short door panels from a lower angle into the vertical position inside the chamber, and then rotating around the chamber for installation onto the existing ceiling and floor. The LD rotates 360 (in very small increments) in both clockwise and counterclockwise directions. Eight lifting pads are on the top ring with 2-in. (.5-cm) eye holes spaced evenly around the ring to allow for the device to be suspended by three crane hoists from the top of the chamber. The LD is operated by remote controls that allow for a single, slow mode for booming the load in and out, with slow and very slow modes for rotating the load.

Tolleson, William↗
NASA NTRS2013

Motorized Beam Alignment of a Commercial X-ray Diffractometer

X-ray diffraction (XRD) is a powerful analysis method that allows researchers to noninvasively probe the crystalline structure of a material. This includes the ability to determine the crystalline phases present, quantify surface residual stresses, and measure the distribution of crystallographic orientations. The Structures and Materials Division at the NASA Glenn Research Center (GRC) heavily uses the on-site XRD lab to characterize advanced metal alloys, ceramics, and polymers. One of the x-ray diffractometers in the XRD lab (Bruker D8 Discover) uses three different x-ray tubes (Cu, Cr, and Mn) for optimal performance over numerous material types and various experimental techniques. This requires that the tubes be switched out and aligned between experiments. This alignment maximizes the x-ray tube s output through an iterative process involving four set screws. However, the output of the x-ray tube cannot be monitored during the adjustment process due to standard radiation safety engineering controls that prevent exposure to the x-ray beam when the diffractometer doors are open. Therefore, the adjustment process is a very tedious series of blind adjustments, each followed by measurement of the output beam using a PIN diode after the enclosure doors are shut. This process can take up to 4 hr to perform. This technical memorandum documents an in-house project to motorize this alignment process. Unlike a human, motors are not harmed by x-ray radiation of the energy range used in this instrument. Therefore, using motors to adjust the set screws will allow the researcher to monitor the x-ray tube s output while making interactive adjustments from outside the diffractometer. The motorized alignment system consists of four motors, a motor controller, and a hand-held user interface module. Our goal was to reduce the alignment time to less than 30 min. The time available was the 10-week span of the Lewis' Educational and Research Collaborative Internship Project (LERCIP) summer internship program and the budget goal was $1200. In this report, we will describe our motorization design and discuss the results of its implementation.

Van Zandt, Noah R.↗
NASA NTRS2013

The Thermal Hogan - A Means of Surviving the Lunar Night

document describes the Thermal Hogan, a new shelter concept that would be used on the Moon to moderate the extreme nighttime temperatures, allowing survival of equipment with minimal heater power. It is lightweight, has few mechanical parts, and would be relatively easy to deploy on the Moon. The Lunar Hogan has two parts: an insulated shelter and a thermal mass. The shelter is constructed of multilayer insulation (MLI) draped over a structural framework. Entry and egress are accomplished either by raising the structure or via a door constructed of the same MLI material as the shelter. The thermal mass can be manufactured from locally available materials, either by piling substantially sized rocks to a depth of 0.25 meter, or by filling a 0.25-meter-deep conductive honeycomb-like structure with lunar dust. For ease of transport, the structural framework and honeycomb can be collapsible. The door can be opened by pushing on it in either direction. Gravity would cause it to close and it could be sealed via magnetic strips on the doorframe.

Fruitwala, Neelay↗
NASA NTRS2014

VAB Temperature and Humidity Study

In 2012, 17 data loggers were placed in the VAB to measure temperature and humidity at 10-minute intervals over a one-year period. In 2013, the data loggers were replaced with an upgraded model and slight adjustments to their locations were made to reduce direct solar heating effects. The data acquired by the data loggers was compared to temperature data provided by three wind towers located around the building. It was found that the VAB acts as a large thermal filter, delaying and reducing the thermal oscillations occurring outside of the building. This filtering is typically more pronounced at higher locations in the building, probably because these locations have less thermal connection with the outside. We surmise that the lower elevations respond more to outside temperature variations because of air flow through the doors. Temperatures inside the VAB rarely exceed outdoor temperatures, only doing so when measurements are made directly on a surface with connection to the outside (such as a door or wall) or when solar radiation falls directly on the sensor. A thermal model is presented to yield approximate filter response times for various locations in the building. Appendix A contains historical thermal and humidity data from 1994 to 2009.

Temperature↗
NASA NTRS2014

Design and Test of a Deployable Radiation Cover for the REgolith X-Ray Imaging Spectrometer

The REgolith X-ray Imaging Spectrometer (REXIS) instrument contains a one-time deployable radiation cover that is opened using a shape memory alloy actuator (a "Frangibolt") from TiNi Aerospace and two torsion springs. The door will be held closed by the bolt for several years in cold storage during travel to the target asteroid, Bennu, and it is imperative to gain confidence that the door will open at predicted operational temperatures. This paper briefly covers the main design features of the radiation cover and measures taken to mitigate risks to cover deployment. As the chosen FD04 model Frangibolt actuator has minimal flight heritage, the main focus of this paper is the testing, results and conclusions with the FD04 while discussing key lessons learned with respect to the use of the FD04 actuator in this application.

Carte, David B.↗
NASA NTRS2018

Asymmetric Thrust Reversers

An aircraft includes a propulsion supported within an aft portion of a fuselage A thrust reverser is mounted in the aft portion of the fuselage proximate the propulsion system for directing thrust in a direction to slow the aircraft. The thrust reverser includes an upper blocker door movable about a first pivot axis to a deployed position and a lower blocker door movable about a second pivot axis not parallel to the first pivot axis.

Chandler, Jesse M.↗
NASA NTRS2019

Air Mobility Data & Reasoning Fabric

Throughout the world, especially in dense urban environments, the quality of life is being negatively impacted by ever growing commute time. Travel, beyond commuting, is increasingly driven by door-to-door challenges ? not just gate-to-gate considerations. Air Mobility may be an approach to address these challenges, as it can effectively convert our 2D mobility system to a 3D mobility system, vastly increasing mobility options.

Van Dalsem, William R.↗
NASA NTRS2018

Exploratory Analysis of the Airspace Throughput and Sensitivities of an Urban Air Mobility System

The use of small, vertical-takeoff and landing aircraft to provide efficient, high-speed, ondemand passenger transportation within a metropolitan area (e.g. intra-city transportation) is a topic of increasing interest and investment within the aerospace and transportation communities. Preliminary, mostly vehicle-level analysis suggests that passenger-carrying “Urban Air Mobility” has the potential to provide meaningful door-to-door trip time savings compared to identical trips taken solely by automobile, even for relatively short trips of a few tens of miles. Subsequent analysis has shown that if such trips can be conducted at costs competitive with ground transportation, the demand for such flight operations, not surprisingly, becomes unprecedented by historical airspace operations counts, raising fundamental questions regarding feasibility, practicality, capacity and basic system attributes such as separation criteria. In this paper, we conduct a preliminary assessment of vertipad requirements and en route separation minima relative to the feasibility of large-scale urban aviation operations. This analysis is acknowledged as being far from comprehensive and is intended to help define the initial boundaries of an airspace system compatible with enabling high-volume operations.

Goodrich, Kenneth H.↗
NASA NTRSDate not supplied

Air Mobility Data & Reasoning Fabric

Throughout the world, especially in dense urban environments, the quality of life is being negatively impacted by ever growing commute time. Travel, beyond commuting, is increasingly driven by door-to-door challenges ? not just gate-to-gate considerations. Air Mobility may be an approach to address these challenges, as it can effectively convert our 2D mobility system to a 3D mobility system, vastly increasing mobility options.

Air mobility↗
NASA NTRSDate not supplied

Nonlinear Buckling Analysis of Tow-Steered Composite Cylinders with Cutouts

The buckling and postbuckling behavior of two composite tow-steered shells with cutouts of different sizes is assessed using nonlinear finite element (FE) analysis and compared to experimental measurements. The cylindrical shells are manufactured using an automated fiber placement system, where the shells’ fiber orientation angles vary continuously around the shell circumference from ±10 degrees on the crown and keel to ±45 degrees on the sides. One shell features thickness variations due to tow overlaps that result from application of all 24 tows during each pass of the fiber placement system. The second shell uses the system’s tow drop/add capability to achieve a more uniform wall thickness without overlaps. Unreinforced cutouts of two different sizes—the first smaller cutout representing a passenger door on a commercial aircraft and the second larger cutout a cargo door—were machined into each of the two cylinders resulting in a total of four test cases. These cylinders were tested in axial compression and buckled elastically in previous work and are now analyzed using nonlinear FE models to compare bifurcation buckling loads as well as the load-displacement response in the prebuckling and postbuckling regimes. For all four shells analyzed, the prebuckling stiffness, buckling load, and deformation mode sequence throughout the loading-unloading cycle is accurately reproduced by the models. In particular, the shells first buckle locally around the cutouts in a stable (super-critical) manner with only a slight decrease in axial stiffness, which occurs due to the favorable load redistribution facilitated by tow steering. The shells then buckle globally in an unstable (sub-critical) manner with diamond-shaped buckles forming to the left and right of the cutouts. The buckling load of all shells with cutouts is at least 82% of the buckling load of the pristine shells without cutouts. Overall, the ability to sustain local buckling phenomena, and the relatively small reductions in global buckling load compared to pristine shells without cutouts, demonstrates the great potential of using tow steering to mitigate the adverse effects of cutouts in axially-compressed shell structures.

composites↗
NASA NTRSDate not supplied

Nonlinear Buckling Analysis of Tow-Steered Composite Cylinders with Cutouts

The buckling and postbuckling behavior of two composite tow-steered shells with cutouts of different sizes is assessed using nonlinear finite element (FE) analysis and compared to experimental measurements. The cylindrical shells are manufactured using an automated fiber placement system, where the shells’ fiber orientation angles vary continuously around the shell circumference from 10 degrees on the crown and keel to 45 degrees on the sides. One shell features thickness variations due to tow overlaps that result from application of all 24 tows during each pass of the fiber placement system. The second shell uses the system’s tow drop/add capability to achieve a more uniform wall thickness without overlaps. Unreinforced cutouts of two different sizes—the first smaller cutout representing a passenger door on a commercial aircraft and the second larger cutout a cargo door—were machined into each of the two cylinders resulting in a total of four test cases. These cylinders were tested in axial compression and buckled elastically in previous work and are now analyzed using nonlinear FE models to compare bifurcation buckling loads as well as the load-displacement response in the prebuckling and postbuckling regimes. For all four shells analyzed, the prebuckling stiffness, buckling load, and deformation mode sequence throughout the loading-unloading cycle is accurately reproduced by the models. In particular, the shells first buckle locally around the cutouts in a stable (super-critical) manner with only a slight decrease in axial stiffness, which occurs due to the favorable load redistribution facilitated by tow steering. The shells then buckle globally in an unstable (sub-critical) manner with diamond-shaped buckles forming to the left and right of the cutouts. The buckling load of all shells with cutouts is at least 82% of the buckling load of the pristine shells without cutouts. Overall, the ability to sustain local buckling phenomena, and the relatively small reductions in global buckling load compared to pristine shells without cutouts, demonstrates the great potential of using tow steering to mitigate the adverse effects of cutouts in axially-compressed shell structures.

Buckling↗