Search NASA⌕ Search

SEARCH · Search NASA

Results for “Deformation Gradient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Impact of control blade insertion on the deformation behavior of SiC-SiC channel boxes in BWRs

This article describes the analysis of distortion of a silicon carbide fiber-reinforced, silicon carbide matrix (SiC-SiC) composite channel box under in-reactor conditions of a boiling water reactor (BWR). The BWR core has significant gradients in the fast neutron flux across the channel box due to the presence of water rods within the fuel assemblies, and these gradients increase further with the insertion of control blades. As a result of the temperature and neutron flux dependent irradiation-induced swelling of SiC, the SiC-SiC composite channel box can undergo distortion. In this work, we evaluate the SiC-SiC channel box distortion for three different control blade positions. This analysis is based on the neutron flux and temperature distributions in the BWR core calculated using the neutronics code MPACT and thermal-hydraulics code CTF. This calculation is coupled through temperature feedback. Subsequently, we have performed structural analysis based on the calculated neutron flux and temperature distributions to determine the deformation and stress development in the channel box. The structural analysis was performed using the fuel performance modeling code BISON and the commercial finite element analysis software Abaqus. The results indicate that large gradients in fast neutron flux (up to 35–40% across a single axial level) will develop across the channel box. Due to these gradients, the channel box will undergo time-dependent bending for all the control blade positions in the assembly. The time-dependent bowing behavior is dominated by the transient swelling of SiC-SiC material under non-uniform neutron flux, and changes with variation in the control blade position. The bending will cause temporary interference between the channel box and control blade, and the interference is expected to be most severe for the fully inserted control blade position. The developed stresses due to differential swelling in the channel box exceed the proportional limit stress of the material, which may cause matrix microcracking in the channel box. However, the stresses remain below the tensile strength of the material, and therefore, development of a full, through-thickness crack in the channel box is not expected. Finally, further work is recommended to explore and evaluate the mitigation strategies.

42 ENGINEERING↗
DOE OSTI2023

Capturing the softening in T91 steel annealed with molten LBE through interfacial gradient plasticity

In order to study the effect of annealing with molten lead–bismuth eutectic alloy (mLBE) on the mechanical properties of T91 steel, micropillar compression tests were analyzed through the consideration of mechanical interface energy terms within gradient plasticity. The stress–strain curves of the micropillars showed significant stochastic effects, characterized by a different elastic and plastic behavior response for each pillar. Among the various pillars, some exhibited a similar trilinear behavior. Scanning electron microscopy (SEM) images of these specimens demonstrated localized slip deformation and slip planes after compression, while transmission electron microscopy (TEM) images showed the presence of a severe slip zone along the random grain boundaries (RGBs), indicating that the GBs played a dominant role in the deformation/slip. By employing interfacial gradient plasticity that can explicitly account for the presence of GBs, the trilinear response was captured, allowing for the determination of the mechanical interface parameter. As anticipated the pillars which underwent severe slip at the GBs had a lower value for the mechanical interface parameter. Finally, annealing with mLBE can, therefore, in some cases result in softening in the overall stress–strain, as it lowers the mechanical interface energy of GBs.

36 MATERIALS SCIENCE↗
NASA NTRS1992

Deformation mechanisms of NiAl cyclicly deformed near the brittle-to-ductile transformation temperature

One of the ongoing challenges of the aerospace industry is to develop more efficient turbine engines. Greater efficiency entails reduced specific strength and larger temperature gradients, the latter of which means higher operating temperatures and increased thermal conductivity. Continued development of nickel-based superalloys has provided steady increases in engine efficiency and the limits of superalloys have probably not been realized. However, other material systems are under intense investigation for possible use in high temperature engines. Ceramic, intermetallic, and various composite systems are being explored in an effort to exploit the much higher melting temperatures of these systems. NiAl is considered a potential alternative to conventional superalloys due to its excellent oxidation resistance, low density, and high melting temperature. The fact that NiAl is the most common coating for current superalloy turbine blades is a tribute to its oxidation resistance. Its density is one-third that of typical superalloys and in most temperature ranges its thermal conductivity is twice that of common superalloys. Despite these many advantages, NiAl requires more investigation before it is ready to be used in engines. Binary NiAl in general has poor high-temperature strength and low-temperature ductility. On-going research in alloy design continues to make improvements in the high-temperature strength of NiAl. The factors controlling low temperature ductility have been identified in the last few years. Small, but reproducible ductility can now be achieved at room temperature through careful control of chemical purity and processing. But the mechanisms controlling the transition from brittle to ductile behavior are not fully understood. Research in the area of fatigue deformation can aid the development of the NiAl system in two ways. Fatigue properties must be documented and optimized before NiAl can be applied to engineering systems. More importantly though, probing the deformation mechanisms operating in fatigue will lead to a better understanding of NiAl's unique characteristics. Low cycle fatigue properties have been reported on binary NiAl in the past year, yet those studies were limited to two temperature ranges: room temperature and near 1000 K. Eventually, fatigue property data will be needed for a wide range of temperatures and compositions. The intermediate temperature range near the brittle-to-ductile transition was chosen for this study to ascertain whether the sharp change occurring in monotonic behavior also occurs under cyclic conditions. An effort was made to characterize the dislocation structures which evolved during fatigue testing and comment on their role in the deformation process.

Antolovich, Stephen D.↗
DOE OSTI2022

Enhanced polarization and abnormal flexural deformation in bent freestanding perovskite oxides

Abstract Recent realizations of ultrathin freestanding perovskite oxides offer a unique platform to probe novel properties in two-dimensional oxides. Here, we observe a giant flexoelectric response in freestanding BiFeO 3 and SrTiO 3 in their bent state arising from strain gradients up to 3.5 × 10 7 m −1 , suggesting a promising approach for realizing ultra-large polarizations. Additionally, a substantial change in membrane thickness is discovered in bent freestanding BiFeO 3 , which implies an unusual bending-expansion/shrinkage effect in the ferroelectric membrane that has never been seen before in crystalline materials. Our theoretical model reveals that this unprecedented flexural deformation within the membrane is attributable to a flexoelectricity–piezoelectricity interplay. The finding unveils intriguing nanoscale electromechanical properties and provides guidance for their practical applications in flexible nanoelectromechanical systems.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS1992

Studies of regional and global tectonics and the rotation of the earth using very-long-baseline interferometry

Work is continuing on the study of atmospheric gradients. We include a preprint entitled 'The effect of turbulence on atmospheric gradient parameters determined from ground-based radiometric and space geodetic measurements'. Work has begun on a study of solid Earth tidal deformations using the VLBI data set. We have examined deformations at the semi-diurnal tidal period using the IRIS data set.

Shapiro, Irwin I.↗
NASA NTRS1992

The internal dynamics of slowly rotating biological systems

The structure and the dynamics of biological systems are complex. Steady gravitational forces that act on organisms cause hydrostatic pressure gradients, stress in solid components, and ordering of movable subsystems according to density. Rotation induces internal motion; it also stresses and or deforms regions of attachment and containment. The disrupted gravitationally ordered layers of movable entities are replaced by their orbital movements. New ordering geometries may arise also, especially if fluids of various densities occur. One novel result obtained concerns the application of scheduled variation of clinostat rotation rates to the management of intracellular particle trajectories. Rotation and its consequences are discussed in terms of scaling factors for parameters such as time, derived from mathematical models for simple rotating mechanical systems.

Kessler, John O.↗
NASA NTRS2009

Advances in Non-contact Measurement of Creep Properties

Our team has developed a novel approach to measuring creep at extremely high temperatures using electrostatic levitation (ESL). This method has been demonstrated on niobium up to 2300 C, while ESL has melted tungsten (3400 C). High-precision machined spheres of the sample are levitated in the NASA MSFC ESL, a national user facility, and heated with a laser. The laser is aligned off-center so that the absorbed photons transfer their momentum to the sample, causing it to rotate at up to 250,000+ RPM. The rapid rotation loads the sample through centripetal acceleration, causing it to deform. The deformation of the sample is captured on high-speed video, which is analyzed by machine-vision software from the University of Massachusetts. The deformations are compared to finite element models to determine the constitutive constants in the creep relation. Furthermore, the noncontact method exploits stress gradients within the sample to determine the stress exponent in a single test. This method was validated in collaboration with the University of Tennessee for niobium at 1985 C, with agreement within the uncertainty of the conventional measurements. A similar method is being employed on Ultra-High-Temperature ZrB2- SiC composites, which may see application in rocket nozzles and sharp leading edges for hypersonic vehicles.

Hyers, Robert W.↗
NASA NTRS2010

Modeling Near-Crack-Tip Plasticity from Nano- to Micro-Scales

Several efforts that are aimed at understanding the plastic deformation mechanisms related to crack propagation at the nano-, meso- and micro-length scales including atomistic simulation, discrete dislocation plasticity, strain gradient plasticity and crystal plasticity are discussed. The paper focuses on discussion of newly developed methodologies and their application to understanding damage processes in aluminum and its alloys. Examination of plastic mechanisms as a function of increasing length scale illustrates increasingly complex phenomena governing plasticity

Glaessgen, Edward H.↗
NASA NTRS1989

Elevated temperature crack growth

Alloy 718 crack growth experiments were conducted to assess the ability of the selected path-independent (P-I) integrals to describe the elevated temperature crack growth behavior. These tests were performed on single edge notch (SEN) specimens under displacement control with multiple extensometers to monitor the specimen and crack mouth opening displacement (CMOD). The displacements in these tests were sufficiently high to induce bulk cyclic inelastic deformation of the specimen. Under these conditions, the linear elastic fracture mechanics (LEFM) parameter K does not correlate the crack growth data. The experimentally measured displacement gradients at the end of specimen gage length were used as the boundary conditions in elastic-plastic finite element method (FEM) analyses. These analyses were performed with a node release approach using CYANIDE, a GEAE FEM code, which included a gap element which is capable of efficiently simulating crack closure. Excellent correlation was obtained between the experimentally measured and predicted variation of stress and CMOD with crack length and the stress-CMOD loops for Alloy 718 tests conducted at 538 C. This confirmed the accuracy of the FEM crack growth simulation approach. The experimentally measured crack growth rate data correlated well the selected P-I integrals. These investigations have produced significant progress in developing P-I integrals as non-linear fracture mechanics parameters. The results suggest that this methodology has the potential of accurately describing elevated temperature crack growth behavior under the combined influence of thermal cycling and bulk elastic-inelastic deformation states.

Kim, K. S.↗
NASA NTRS1990

Materials with periodic internal structure: Computation based on homogenization and comparison with experiment

The combination of thermal and mechanical loading expected in practice means that constitutive equations of metal matrix composites must be developed which deal with time-independent and time-dependent irreversible deformation. Also, the internal state of composites is extremely complicated which underlines the need to formulate macroscopic constitutive equations with a limited number of state variables which represent the internal state at the micro level. One available method for calculating the macro properties of composites in terms of the distribution and properties of the constituent materials is the method of homogenization whose formulation is based on the periodicity of the substructure of the composite. A homogenization procedure was developed which lends itself to the use of the finite element procedure. The efficiency of these procedures, to determine the macroscopic properties of a composite system from its constituent properties, was demonstrated utilizing an aluminum plate perforated by directionally oriented slits. The selection of this problem is based on the fact that, extensive experimental results exist, the macroscopic response is highly anisotropic, and that the slits provide very high stress gradients which severely test the effectiveness of the computational procedures. Furthermore, both elastic and plastic properties were investigated so that the application to practical systems with inelastic deformation should be able to proceed without difficulty. The effectiveness of the procedures was rigorously checked against experimental results and with the predictions of approximate calculations. Using the computational results it is illustrated how macroscopic constitutive equations can be expressed in forms of the elastic and limit load behavior.

Jansson, S.↗
NASA NTRS1995

Localization of toroidal motion and shear heating in 3-D high Rayleigh number convection with temperature-dependent viscosity

We have applied spectral-transform methods to study three-dimensional thermal convection with temperature-dependent viscosity. The viscosity varies exponentially with the form exp(-BT), where B controls the viscosity contrast and T is temperature. Solutions for high Rayleigh numbers, up to an effective Ra of 6.25 x 10(exp 6), have been obtained for an aspect-ratio of 5x5x1 and a viscosity contrast of 25. Solutions show the localization of toroidal velocity fields with increasing vigor of convection to a coherent network of shear-zones. Viscous dissipation increases with Rayleigh number and is particularly strong in regions of convergent flows and shear deformation. A time-varying depth-dependent mean-flow is generated because of the correlation between laterally varying viscosity and velocity gradients.

Balachandar, S.↗
NASA NTRS2015

Variable-Domain Displacement Transfer Functions for Converting Surface Strains into Deflections for Structural Deformed Shape Predictions

Variable-Domain Displacement Transfer Functions were formulated for shape predictions of complex wing structures, for which surface strain-sensing stations must be properly distributed to avoid jointed junctures, and must be increased in the high strain gradient region. Each embedded beam (depth-wise cross section of structure along a surface strain-sensing line) was discretized into small variable domains. Thus, the surface strain distribution can be described with a piecewise linear or a piecewise nonlinear function. Through discretization, the embedded beam curvature equation can be piece-wisely integrated to obtain the Variable-Domain Displacement Transfer Functions (for each embedded beam), which are expressed in terms of geometrical parameters of the embedded beam and the surface strains along the strain-sensing line. By inputting the surface strain data into the Displacement Transfer Functions, slopes and deflections along each embedded beam can be calculated for mapping out overall structural deformed shapes. A long tapered cantilever tubular beam was chosen for shape prediction analysis. The input surface strains were analytically generated from finite-element analysis. The shape prediction accuracies of the Variable- Domain Displacement Transfer Functions were then determined in light of the finite-element generated slopes and deflections, and were fofound to be comparable to the accuracies of the constant-domain Displacement Transfer Functions

displacement transfer functions↗
NASA NTRS1994

A structural fabric defined by topographic lineaments: Correlation with Tertiary deformation of Ellesmere and Axel Heiberg Islands, Canadian Arctic

Digital topographic contours from four 1:250000 scale maps have been gridded to produce a digital elevation model for part of Ellesmere and Axel Heiberg islands in the Canadian Arctic Islands. Gradient calculations were used to define both east and west dipping slopes defining a pattern of lineaments that have been compared with mapped geological structures. In ice-covered areas, where geological mapping was not possible, well-defined topographic lineaments have been identified and are correlated to extensions of major structural features. The northeast-southwest patterns of both topographic lineaments and mapped structures are strongly unimodal and support a single compressive event oriented at 67 deg west of north. This orientation is coincidental with the convergence direction calculated from the kinematic poles of rotation for Greenland relative to North America between 56 and 35 Ma. A minor secondary peak at 70 east of north is observed for thrust and normal fault solutions and is not directly related to the predicted convergence direction. Whether this represents a unique phase of deformation or is a subcomponent of a single event is not known. The agreement of structural components, lineament orientations, and convergence direction suggests an overwhelming over print of Eurekan deformation on any preexisting structural fabric. This study confirms, for the first time, an excellent compatibility between geological and geophysical constraints for the timing and geometry of the Eurekan orogeny.

Oakey, Gordon↗
DOE OSTI2022

Investigation of deformation mechanisms in an advanced FeCrAl alloy using in-situ SEM-EBSD testing

The deformation mechanisms associated with uniaxial tensile testing are observed by conducting tensile experiments of an FeCrAl alloy using scanning electron microscopy (SEM) coupled with electron backscattered diffraction (EBSD). Prior to the deformation, investigated alloy was consisting grain and precipitate size of ~63.0 μm and ~6.7 μm, respectively. The recorded SEM micrographs and EBSD data at increasing levels of strains revealed the complex phenomena of slip bands’ formation in the presence of surface grain morphology evolution and their (001), (110) and (111) crystallographic planes distortions. The grains with orientation (110)||tensile direction (TD) shows higher shape change; however, (001)||TD and (111)||TD oriented grains show higher lattice gradient formation. Extracted information from the EBSD indicates that the crystallographic rotations drive towards specific, fiber-like texture in relation to the loading direction. Postmortem analysis of the recorded microstructure during the tensile deformation explains the phenomena of crack formation in the hard-intermetallic particles before the ultimate tensile strength (UTS). However, after the UTS, pores were identified in the neck that resulted from extensive plastic deformation. In-depth analysis was carried out to identify the cause of cracks and pores formation phenomena during the tensile test.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Study of the interplay between lower-order and higher-order energetic strain-gradient effects in polycrystal plasticity

in this report strain-gradient (SG) plasticity refers to a class of non-local theories in which gradients of plastic slip determine the storage of geometrically necessary dislocations, introducing a length-scale dependence in the mechanical behavior of crystalline materials, which is otherwise lacking in local theories. In this work, we incorporate lower-order (LO) and higher-order energetic (HOE) strain-gradient effects into a crystal plasticity fast Fourier transform (FFT)-based formulation to investigate the interplay of the length scale that each strain-gradient term introduces at the microscale, and the mechanical properties that result at the macroscale. For an applicable range of length scales, we consider two systems: a 1-D two-phase face centered cubic (FCC) laminate and a 3-D FCC polycrystal, and two uniaxial deformation modes: monotonic tension and cyclic tension–compression. We show that increases in the individual LO and HOE length scales increase the hardening rate and strength of the material, respectively. When combined, the strong LO hardening is less pronounced than the effect alone due to the lowering of the gradients due to the HOE microstress. We demonstrate that the LO and HOE hardening manifest as “isotropic” (yield surface expansion) and “kinematic” (yield surface shift) effects, respectively, consistent with their theoretical origins. We show that in cyclic loading, the Bauschinger effect emerges in both local and non-local calculations and link its origins and severity to the behavior in the strain field, slip-system rates, and the HOE microforce.

36 MATERIALS SCIENCE↗
NASA NTRS2010

Improved Creep Measurements for Ultra-High Temperature Materials

Our team has developed a novel approach to measuring creep at extremely high temperatures using electrostatic levitation (ESL). This method has been demonstrated on niobium up to 2300 C, while ESL has melted tungsten (3400 C). This method has been extended to lower temperatures and higher stresses and applied to new materials, including a niobium-based superalloy, MASC. High-precision machined spheres of the sample are levitated in the NASA MSFC ESL, a national user facility and heated with a laser. The samples are rotated with an induction motor at up to 30,000 revolutions per second. The rapid rotation loads the sample through centripetal acceleration, producing a shear stress of about 60 MPa at the center, causing the sample to deform. The deformation of the sample is captured on high-speed video, which is analyzed by machine-vision software from the University of Massachusetts. The deformations are compared to finite element models to determine the constitutive constants in the creep relation. Furthermore, the non-contact method exploits stress gradients within the sample to determine the stress exponent in a single test.

Hyers, Robert W.↗
DOE OSTI2026

Instabilities and phase transitions in architected metamaterials: a gradient-enhanced continuum approach

Architected metamaterials such as foams and lattices exhibit a wide range of properties governed by microstructural instabilities and emerging phase transitions. Their macroscopic response–including energy dissipation during impact, large recoverable deformations, morphing between configurations, and auxetic behavior–remains difficult to capture with conventional continuum models, which often rely on discrete approaches that limit scalability. In this work, we propose a nonlocal continuum formulation that captures both stable and unstable responses of elastic architected metamaterials. The framework extends anisotropic hyperelasticity by introducing nonlocal variables and internal length scales reflective of microstructural features. Local polyconvex free-energy models are systematically augmented with two families of non-(poly)convex energies, enabling both metastable and bistable responses. Implementation in a finite element framework enables solution using a hybrid monolithic–staggered strategy. Simulations capture densification fronts, forward and reverse transitions, hysteresis loops, imperfection sensitivity, and globally coordinated auxetic modes. Overall, this framework provides a robust foundation for accelerated modeling of instability-driven phenomena in architected metamaterials, while enabling extensions to anisotropic, dissipative, and active systems as well as integration with data-driven and machine learning approaches.

42 ENGINEERING↗
DOE OSTI2024

Demonstration and Verification of Thermo-Mechanical Bowing in a Limited Free-Bow SFR Concept Using MOOSE

Core bowing due to thermal gradients and irradiation induced swelling and creep introduces significant reactivity feedback effects in liquid metal-cooled fast spectrum reactors. During startup, normal operations, and transient events, differential thermal and flux gradients cause expansion, creep, and swelling, which results in bowing in preferential directions depending on local material properties and load-pad and restraint-ring design. The bowing phenomenon produces negative reactivity during accident conditions provided the restraint system has been properly designed to optimally guide the deformation outwards in the active core region. Under the Department of Energy Nuclear Energy Advanced Modeling and Simulation program, a Multiphysics Object Oriented Simulation Environment (MOOSE)-based multiphysics approach to model core bowing is being developed. The present work expands on previous modeling of simpler International Atomic Energy Agency (IAEA) verification problems with these tools by modeling IAEA Verification Problem 4, which involves a symmetric sector of a reactor core with ducted assemblies undergoing differential thermal expansion due to thermal gradients bowing outward with duct-to-duct contact. This model is available on the National Reactor Innovation Center Virtual Test Bed repository. This example was verified against benchmark participant results, which includes bowing deformation evaluation and duct-to-duct interactions at load pads with mechanical contact.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗