Search NASA⌕ Search

SEARCH · Search NASA

Results for “Design Load”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS2008

Optimization of Stability Constrained Geometrically Nonlinear Shallow Trusses Using an Arc Length Sparse Method with a Strain Energy Density Approach

A technique for the optimization of stability constrained geometrically nonlinear shallow trusses with snap through behavior is demonstrated using the arc length method and a strain energy density approach within a discrete finite element formulation. The optimization method uses an iterative scheme that evaluates the design variables' performance and then updates them according to a recursive formula controlled by the arc length method. A minimum weight design is achieved when a uniform nonlinear strain energy density is found in all members. This minimal condition places the design load just below the critical limit load causing snap through of the structure. The optimization scheme is programmed into a nonlinear finite element algorithm to find the large strain energy at critical limit loads. Examples of highly nonlinear trusses found in literature are presented to verify the method.

Hrinda, Glenn A.↗
NASA NTRS2009

Vibration Challenges in the Design of NASA's Ares Launch Vehicles

This paper focuses on the vibration challenges inherent in the design of NASA s Ares launch vehicles. A brief overview of the launch system architecture is provided to establish the context for the discussion. Following this is a general discussion of the design considerations and analytical disciplines that are affected by vibration. The first challenge discussed is that of coupling between the vehicle flight control system and fundamental vibrational modes of the vehicle. The potential destabilizing influence of the vibrational dynamics is described along with discussion of the typical methods employed to overcome this issue. Next is a general discussion of the process for developing the design loads for the primary structure. This includes quasi-steady loads and dynamic loads induced by the structural dynamic response. The two principal parts of this response are the gust induced responses of the lower frequency modes and the buffet induced responses of the higher frequency modes. Structural dynamic model validation will also be addressed. Following this, discussions of three somewhat unique topics of Pogo Instability, Solid Booster Thrust Oscillation, and Liquid Rocket Engine Turbopump Rotordynamic Stability and Response are presented.

Ryan, Stephen G.↗
NASA NTRS2010

Constellation Program DOLILU Operational Concepts

Day of launch I-load uplink (DOLILU) and a corresponding day of launch trajectory and loads evaluation are being considered for the Constellation Program. Abort effectiveness, controllability, and ascent structural loads all improve with some of the flight software I-loads designed using current measured atmospheric conditions. While a generalized DOLILU framework has been assumed, specific implementation details have not yet been discussed in depth nor documented. Operational improvements can be leveraged from Space Shuttle experience to create a more cost-effective and streamlined process while maintaining the integrity of the results. A preliminary discussion of DOLILU design methodology is presented followed by some suggestions and implementation details for Constellation Program DOLILU operations

Puperi, Daniel S.↗
NASA NTRS2011

Enhancements to TetrUSS for NASA Constellation Program

The NASA Constellation program is utilizing Computational Fluid Dynamics (CFD) predictions for generating aerodynamic databases and design loads for the Ares I, Ares I-X, and Ares V launch vehicles and for aerodynamic databases for the Orion crew exploration vehicle and its launch abort system configuration. This effort presents several challenges to applied aerodynamicists due to complex geometries and flow physics, as well as from the juxtaposition of short schedule program requirements with high fidelity CFD simulations. NASA TetrUSS codes (GridTool/VGRID/USM3D) have been making extensive contributions in this effort. This paper will provide an overview of several enhancements made to the various elements of TetrUSS suite of codes. Representative TetrUSS solutions for selected Constellation program elements will be shown. Best practices guidelines and scripting developed for generating TetrUSS solutions in a production environment will also be described.

Pandya, Mohagna J.↗
NASA NTRS2011

Contributions of TetrUSS to Project Orion

The NASA Constellation program has relied heavily on Computational Fluid Dynamics simulations for generating aerodynamic databases and design loads. The Orion Project focuses on the Orion Crew Module and the Orion Launch Abort Vehicle. NASA TetrUSS codes (GridTool/VGRID/USM3D) have been applied in a supporting role to the Crew Exploration Vehicle Aerosciences Project for investigating various aerodynamic sensitivities and supplementing the aerodynamic database. This paper provides an overview of the contributions from the TetrUSS team to the Project Orion Crew Module and Launch Abort Vehicle aerodynamics, along with selected examples to highlight the challenges encountered along the way. A brief description of geometries and tasks will be discussed followed by a description of the flow solution process that produced production level computational solutions. Four tasks conducted by the USM3D team will be discussed to show how USM3D provided aerodynamic data for inclusion in the Orion aero-database, contributed data for the build-up of aerodynamic uncertainties for the aero-database, and provided insight into the flow features about the Crew Module and the Launch Abort Vehicle.

Mcmillin, Susan N.↗
NASA NTRS1964

Spin-Tunnel Investigation of a 1/30-Scale Model of the North American A-5 Airplane

An investigation has been made to determine the erect and. inverted spin and recovery characteristics of a 1/30-scale dynamic model of the North American A-5A airplane. Tests were made for the basic flight design loading with the center of gravity at 30-percent mean aerodynamic chord and also for a forward position and a rearward position with the center of gravity at 26-percent and 40-percent mean aerodynamic chord, respectively. Tests were also made to determine the effect of full external wing tanks on both wings, and of an asymmetrical condition when only one full tank is carried.

Lee, Henry A.↗
NASA NTRS2019

Development of Composite Sandwich Bonded Longitudinal Joints for Space Launch Vehicle Structures

The NASA Composite Technology for Exploration (CTE) Project is developing and demonstrating critical composite technologies with a focus on composite bonded joints; incorporating materials, design/analysis, manufacturing, and tests that utilize NASA’s expertise and capabilities. The project has goals of advancing composite technologies and providing lightweight structures to support future NASA exploration missions. In particular, the CTE project will demonstrate weight-saving, performance-enhancing composite bonded joint technology for Space Launch System (SLS)-scale composite hardware. Advancements from the CTE project may be incorporated as future block upgrades for SLS structural components. This paper discusses the details of the development of a composite sandwich bonded longitudinal joint for a generic space launch vehicle structure called the CTE Point Design. The paper includes details of the design, analysis, materials, manufacturing, and testing of sub-element joint test articles to test the capability of the joint design. The test results show that the composite longitudinal bonded joint design significantly exceeds the design loads with a 2.0 factor of safety. Analysis pre-test failure predictions for all sub-element bonded joint test coupons were all within 10% of the average test coupon failure load. This testing and analysis provides confidence in the potential use of composite bonded joints for future launch vehicle structures.

Segal, Kenneth N.↗
NASA NTRS1968

Heat-load simulator for heat sink design

Heat-load simulator is fabricated from 1/4-inch aluminum plate with a contact surface equal in dimensions and configuration to those of the electronic installation. The method controls thermal output to simulate actual electronic component thermal output.

Dunleavy, A. M.↗
NASA NTRSDate not supplied

Crashworthiness of a Lift Plus Cruise eVTOL Vehicle Design within Dynamic Loading Environments

To aid in the development of electric Vertical Take-off and Landing (eVTOL) technology, the National Aeronautics and Space Administration has undertaken research initiatives to evaluate and optimize design features of eVTOL aircraft. One such initiative has been to develop energy attenuating design mechanisms to improve eVTOL vehicle crashworthiness. In this study, crashworthiness design mechanisms, implemented within a six-passenger lift plus cruise (LPC) eVTOL concept vehicle, were evaluated under multi-axis dynamic loading conditions. This work builds upon crashworthiness design concepts previously optimized within a simplified vehicle-loading environment. The results of this study found the effectiveness of energy attenuating design mechanisms to be dependent on the complexity of load environment in which they were employed. An increase in off-axis loading resulted in a decrease in occupant protective capability. These results indicate the necessity for evaluating vehicle design across the range of possible dynamic impact conditions to characterize crashworthiness. This work provides preliminary methodology for implementing energy attenuating design mechanisms and evaluating crashworthiness for future UAM markets.

Jacob Putnam↗
NASA NTRS1976

Sustained load crack growth design data for Ti-6Al-4V titanium alloy tanks containing hydrazine

Sustained load crack growth data for Ti-6Al-4V titanium alloy in hydrazine per MIL-P-26536 and refined hydrazine are presented. Fracture mechanics data on crack growth thresholds for heat-treated forgings, aged and unaged welds, and aged and unaged heat-affected zones are reported. Fracture mechanics design curves of crack growth threshold stress intensity versus temperature are generated from 40 to 71 C.

Lewis, J. C.↗
NASA NTRS1977

Microbial load monitor

Design analysis of a microbial load monitor system flight engineering model was presented. Checkout of the card taper and media pump system was fabricated as well as the final two incubating reading heads, the sample receiving and card loading device assembly, related sterility testing, and software. Progress in these areas was summarized.

Caplin, R. S.↗
NASA NTRS1976

Sustained load crack growth design data for Ti-6Al-4V titanium alloy tanks containing hydrazine

Results are presented for an experimental study intended to provide sustained load crack growth (SLCG) data for Ti-6Al-4V titanium alloy tanks containing MIL-P-26536 hydrazine and refined hydrazine. Fracture mechanics data on crack growth threshold for heat-treated forgings, aged and unaged welds, and aged and unaged heat-affected zones (HAZ) are presented. All tests were made on uniaxially loaded fracture mechanics specimens involving part-through cracks, and an electrical discharge machined notch was used to start the crack. Fracture mechanics design curves of crack growth threshold stress intensity versus temperature are obtained for the temperature range 40-71 C. Major conclusions are that extreme susceptibility to SLCG in hydrazine is a universal property of unaged weld metal in Ti-6Al-4V titanium alloy of normal interstitial content, and that aging both weld metal and HAZ at 510 C for 4 hr after welding completely removes all susceptibility to SLCG induced by hydrazine, with less susceptibility to SLCG in refined hydrazine.

Lewis, J. C.↗
NASA NTRS2016

Moving Aerospace Structural Design Practice to a Load and Resistance Factor Approach

Aerospace structures are traditionally designed using the factor of safety (FOS) approach. The limit load on the structure is determined and the structure is then designed for FOS times the limit load - the ultimate load. Probabilistic approaches utilize distributions for loads and strengths. Failures are predicted to occur in the region of intersection of the two distributions. The load and resistance factor design (LRFD) approach judiciously combines these two approaches by intensive calibration studies on loads and strength to result in structures that are efficient and reliable. This paper discusses these three approaches.

Larsen, Curtis E.↗
NASA NTRS1990

Importance of anisotropy on design of compression-loaded composite corrugated panels

An investigation is conducted of the importance of anisotropic terms in the design of composite corrugated panels, for a range of axial compressive load intensities. The two panel configurations treated were panels with tailored laminates and panels with a continuous laminate; both are of interest to aircraft designers and prone to anisotropic effects which are of as-yet undetermined extent. The importance of the anisotropic terms is measured by the difference between the design load and the buckling load obtained from the ultimate structural analysis.

Gurdal, Zafer↗