Search NASA⌕ Search

SEARCH · Search NASA

Results for “Dilute solution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

Mesoporous layered aluminosilicates prepared from protozeolitic nanoclusters: Synthesis, physicochemical and catalytic properties

Mesoporous layered aluminosilicates were prepared by a two-stage route using tetrapropylammonium hydroxide (TPAOH) and hexadecylamine (HAD). First, aluminosilicate sols were prepared from very dilute solutions under mild conditions. The sols contained aluminosilicate nanoclusters of the average size 4 – 5 nm. 27Al NMR studies demonstrated that tumbling alone of the small aluminosilicate nanoclusters due to Brownian motions was removing effectively chemical shift anisotropy, dipolar interactions and narrowing quadrupolar interactions; thus, magic-angle-spinning was not required for obtaining good quality 27Al and 29Si NMR spectra of the sols studied. Quantitative analysis of 29Si NMR spectra allowed following evolution of the signals in time, providing insight into dynamical behavior during formation of sols. Second, the sols with the Si/Al ratios of 12 – 70 were used for preparation of the X-ray amorphous aluminosilicate materials. The samples exhibited good sorption properties due to the presence of the ca. 3 nm slit mesopores, coupled with the presence of Brønsted and Lewis acid sites. The initial reaction rate in the liquid-phase isomerization of ?-pinene and the turnover frequency (TOF) were estimated at relatively low temperature of 348 K. The mesoporous aluminosilicate materials turned out to be very active catalytically; the initial reaction rate was surpassing the rate measured over the reference zeolitic and non-zeolitic materials. TOF on mesoporous materials was also high, 0.15 and 0.27 s-1, in comparison with ZSM-5 (0.02 s-1) and ferrierite type zeolites (0.06 – 0.09 s-1).

Onik, Katarzyna↗

Distinctive Trend of Metal Binding Affinity via Hydration Shell Breakage in Nanoconfined Cavity

Here, we report a distinctive trend in the binding affinity of metal cations when they interact with lacunary Keggin-type polyoxometalate K 7 [α-PW 11 O 39 ] clusters in aqueous media. The binding affinity of metal cations follows the special trends of Li + > Na + > K + for monovalent cations and Mg 2+ > Ca 2+ > Sr 2+ > Ba 2+ for divalent cations, completely reversed from the common trends of Li + < Na + < K + and Mg 2+ < Ca 2+ < Sr 2+ < Ba 2+ for macroion–counterion ion-pair formation in dilution solution. Isothermal titration calorimetry and NMR measurements confirm that the hydration shells of metal cations are significantly broken during the interaction in the nanoscale cavity, making the binding affinity stronger for the cations with smaller ionic sizes instead of hydrated sizes. Furthermore, the same phenomenon is observed for the lacunary Dawson-type clusters, which contain well-defined cavity in their structures as well, demonstrating the universality of this reverse trend and its connection to nanoconfinement effect in small submolecular cavities.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Structure of rigid polymers confined to nanoparticles: Molecular dynamics simulations insight

Nanoparticles (NPs) grafted with organic layers form hybrids able to retain their unique properties through integration into the mesoscopic scale. The organic layer structure and response often determine the functionality of the hybrids on the mesoscopic length scale. Using molecular dynamics (MD) simulations, we probe the conformation of luminescent rigid polymers, dialkyl poly(p-phenylene ethynylene)s (PPE), end-grafted onto a silica nanoparticle in different solvents as the molecular weights and polymer coverages are varied. We find that, in contrast to NP-grafted flexible polymers, the chains are fully extended independent of the solvent. In toluene and decane, which are good solvents, the grafted PPEs chains assume a similar conformation to that observed in dilute solutions. In water, which is a poor solvent for the PPEs, the polymer chains form one large cluster but remain extended. The radial distribution of the chains around the core of the nanoparticle is homogeneous in good solvents, whereas in poor solvents clusters are formed independent of molecular weights and coverages. As a result, the clustering is distinctively different from the response of grafted flexible and semiflexible polymers.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Atomic Edge-Guided Polyethylene Crystallization on Monolayer Two-Dimensional Materials

In this report we combine an advanced synthesis of two-dimensional (2D) materials (MoSe 2 ) having well-defined atomic edge configurations with ab initio and atomistic molecular dynamics (MD) simulations to study how atomic edges interact with polyethylene (HDPE) chains in a dilute solution assembly process. Our results reveal that Mo-terminated zigzag (Mo-ZZ) edges act as preferred nucleation sites and strongly interact with HDPE chains. The HDPE chains align in parallel with the Mo-ZZ edges and form arrays of lamellae that are perpendicular to the edges. Interestingly, atomic edge configurations are observed to dramatically change such interactions. The crystallization discrepancy at different edges was demonstrated on the same piece of MoSe 2 with different types of edges. The ab initio and MD simulations between n-alkane (n = 5 and 25), a segment of HDPE, and MoSe 2 suggest that the atomic structures of MoSe 2 can affect their interactions with n-alkane chains. Following the Mo-ZZ edge preferred nucleation principle, controlled long-range alignment of HDPE lamellae can be realized by creating multilayer MoSe 2 with parallel atomic steps. This research opens a pathway toward an atomic level understanding of polymer–2D nanomaterial interactions. It also bridges the gap between atomic-level and long-range mesoscopic structures and introduces a novel strategy for long-range structural control.

36 MATERIALS SCIENCE↗

Direct Observation on Spin-Coating Process of PS- b -P2VP Thin Films

We studied the structural development of symmetric poly(styrene-b-2-vinylpyridine) (PS-b-P2VP) block copolymers during spin-coating using in situ grazing incidence small angle X-ray scattering (GISAXS) measurements. During the spin-coating process, after the formation of the micelles in dilute solution, the selective solvent induced two kinds of the morphological transition. Firstly, the disordered spherical micelles were transformed into a BCC lattice of spheres of which the (110) plane was oriented perpendicularly to the substrate surface. Secondly, further evaporation induced a transition from spheres on the BCC lattice into cylindrical structures. The orientation of the cylinders perpendicular to the substrate surface was induced by solvent convection perpendicular to the substrate, which occurs during rapid solvent evaporation. After this transition, vitrification of PS and P2VP prevented any further transition from cylinders to the more thermodynamically stable lamellar structures, as are generally observed as the bulk equilibrium state.

block copolymer thin films↗

Poly(methyl methacrylate)- block -poly( n -butyl methacrylate) Diblock Copolymer Micelles in an Ionic Liquid: Scaling of Core and Corona Size with Core Block Length

Here, the structure of poly(methyl methacrylate)-block-poly(n-butyl methacrylate) (PMMA-b-PnBMA) micelles in the room temperature ionic liquid 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([EMIM][TFSI]), a selective solvent for the PMMA block, has been studied using dynamic light scattering (DLS) and small-angle X-ray scattering (SAXS). A series of seven PMMA-b-PnBMA diblock copolymers were prepared by reversible addition–fragmentation chain-transfer (RAFT) polymerization, in which the degree of polymerization of the PMMA block was kept constant while the PnBMA block length was varied. All the polymers formed spherical micelles at ambient temperature in dilute solution; their hydrodynamic radius (R h ) and core radius (R c ) were obtained by DLS and SAXS, respectively. It was found that R c and the degree of polymerization of the core block, NB, followed a power law relationship in which R c ~ NB 0.71±0.01 . The corona thickness (L corona ), given by the difference of Rh and R c , does not show any apparent dependence on NB. These results were compared to scaling theory, and were found to be only in partial agreement with the star model proposed by Halperin et al. However, the mean-field calculations of micellar dimensions by Nagarajan and Ganesh were in excellent agreement with the data. This comprehensive experimental study provides precise quantification of the R c and L corona dependence on core block lengths, due to the use of seven different block copolymers with identical corona block lengths.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Electric-Field-Driven Localization of Molecular Nanowires in Wafer-Scale Nanogap Electrodes

As integrated circuits continue to scale toward the atomic limit, bottom-up processes, such as epitaxial growth, have come to feature prominently in their fabrication. At the same time, chemistry has developed highly tunable molecular semiconductors that can perform the functions of ultimately scaled circuit components. Hybrid techniques that integrate programmable structures comprising molecular components into devices however are sorely lacking. Here we demonstrate a wafer-scale process that directs the localization of a conductive polymer, M w = 20 kg mol –1 polyaniline, from dilute solutions into 50 nm vertical nanogap device architectures using electric-field-driven self-assembly. The resulting metal–polymer–metal junctions were characterized by electron microscopy, Raman spectroscopy and transport measurements demonstrating that our technique is highly selective, assembling conductive polymers only in electrically activated nanogaps. Our results represent a step toward scalable hybrid nanoelectronics that seamlessly integrate established lithographic top-down fabrication with bottom-up synthesized molecular functional circuit components.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

High-Temperature Rotating Disk Electrode Study of Platinum Bimetallic Catalysts in Phosphoric Acid

Understanding the H 3 PO 4 effect on the catalyst’s activity under a relevant condition is important for high-temperature polymer electrolyte membrane fuel cell (HT-PEMFC) catalyst research. Here, we report a high-temperature rotating disk electrode (HT-RDE) study of oxygen reduction reaction (ORR) in H 3 PO 4 . With the regular electrochemical protocol, we found that H 3 PO 4 reduction could occur during cyclic voltammetry study and form a reductive species—phosphorus acid (H 3 PO 3 ). Further, to obtain reliable ORR measurement, we optimized the protocol to avoid the H 3 PO 3 generation. The ORR activity of carbon-supported PtM (M = Fe, Co, Ni, Ru, Pd, and Ir) bimetallic alloy catalysts measured with this HT-RDE method showed higher ORR activity than Pt. To understand the alloying effect, we combine experiments in diluted solutions to distinguish the alloying effect on Pt–O binding and Pt–H 3 PO 4 binding. The results indicate that H 3 PO 4 mainly reduces available sites for ORR, with little effect on neighboring site’s Pt–O binding via Pt–H 3 PO 4 interaction, which is also supported by the density functional theory calculation of the Pt–O binding energy with/without H 2 PO 4 . Further study in a phosphoric acid-doped quaternary ammonium-biphosphate ion pair coordinated polyphenylene (PA-QAPOH) membrane electrode assembly (MEA) shows that the active alloy catalyst has better performance in both the HT-RDE and MEA. Also, the MEA gives higher ORR activity than the HT-RDE because of the higher pressure and less phosphoric acid content of the MEA. Yet, the gap between the HT-RDE and MEA is significantly smaller than that between the room temperature (RT)-RDE and MEA, suggesting the importance of temperature and H 3 PO 4 concentration in understanding ORR in HT-PEMFCs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Supertough PLA-Silane Nanohybrids by in Situ Condensation and Grafting

Brittleness is a key barrier for poly(lactic acid) (PLA) toward broader applications. Supertough PLA was achieved by simply mixing a low amount (0.5–1 wt %) of organoalkoxysilane with PLA. Three organosilanes, (3-aminopropyl)triethoxysilane (APTES), 3-(triethoxysilyl)propyl isocyanate (ICPTES), and trimethoxymethylsilane (MTMS), were selected for this study to understand how the functional group on a silane affects the behavior of the PLA-silane hybrids. Remarkable improvements in ultimate tensile strain (up to 12 folds) and tensile toughness (up to 10 folds) were observed in APTES- and ICPTES-modified PLA without any loss in tensile strength and modulus. Glass transition temperatures measured by differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA) did not show any obvious decrease. We propose that in situ condensation of organosilane and grafting of PLA to form a silica-PLA core–shell nanocomplex may be the reason for the improved mechanical properties. Scanning electron microscopy (SEM) showed evidence of nanofibrils at fractured surfaces. Dynamic light scattering (DLS) indicated nanoparticle formation (bimodal, 50–200 nm and <10 nm) in dilute solution, while transmission electron microscopy (TEM) provided clearer evidence of the nanosized silica formed in situ. Rheological studies also showed increased chain entanglement in the polymer melts, which contributed to 1 order of magnitude higher complex viscosity and storage modulus. The simple PLA toughening strategy and the new mechanism revealed in this study will open a door to novel performance polymer materials and broader use of PLAs.

36 MATERIALS SCIENCE↗

Effect of Solvent Quality and Monomer Water Solubility on Soft Nanoparticle Morphology

Previous investigations have identified the correlation between synthetic conditions and soft nanoparticle morphology, including their molecular weight, internal crosslinked structure, total nanoparticle radius, and topology, or degree of “fuzziness” of each nanoparticle. To provide further insight to these guidelines, we examine the effect of surfactant concentration and monomer water solubility on the topology, size, and polydispersity of soft poly(butyl acrylate) nanoparticles. Small-angle neutron scattering studies confirm that increased monomer water solubility and polymer chain flexibility decreases the control of nanoparticle topology and size in a nano-emulsion polymerization. Further studies document the morphological change of polystyrene soft nanoparticles with a decrease in solvent quality. Small-angle neutron scattering was also used to characterize dilute solutions of soft polystyrene nanoparticles in a good and theta solvent, including the analysis of their internal structure. When the soft nanoparticles are dispersed in a thermodynamically good solvent they exhibit a swollen morphology, however, when dispersed in a theta solvent, the nanoparticle core contracts due to unfavorable thermodynamic interactions. Moreover, the structure of soft nanoparticles in a theta solvent provides insight that will guide the interpretation of the behavior of soft nanoparticles dispersed into a bulk polymer matrix.

Martin, Halie J.↗

Encapsulating Semiconductor Quantum Dots in Supramolecular Cages Enables Ultrafast Guest–Host Electron and Vibrational Energy Transfer

In the field of supramolecular chemistry, host- guest systems have been extensively explored to encapsulate a wide range of substrates, owing to emerging functionalities in nano-confined space that cannot be achieved in dilute solutions. However, host-guest chemistry is still limited to encapsulation of small guests. Herein, we construct a water-soluble metallo-supramolecular hexagonal prism with a large hydrophobic cavity by anchoring multiple polyethylene glycol chains onto the building blocks. Then, assembled prisms are able to encapsulate quantum dots (QDs) with diameters of less than 5.0 nm. Furthermore, we find that the supramolecular cage around each QD strongly modifies the photophysics of the QD by universally increasing the rates of QD relaxation processes via ultrafast electron and vibrational energy transfer. In conclusion, taken together, these efforts expand the scope of substrates in host-guest systems and provide a new approach to tune the optical properties of QDs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Conformational Isomerization of Imide Anions Governs Solvation and Transport in Water-in-Salt Electrolytes

The behavior of highly concentrated electrolytes departs radically from the dilute-solution theory, yet the molecular origin of this transformation remains unresolved. Here, we identify the conformational isomerization of molecular ions as a decisive, previously unrecognized control parameter governing structure and transport in crowded aqueous electrolytes. Across a series of fluorosulfonimide anions, we show that increasing concentration drives a collective shift from extended transoid to compact cisoid conformers, revealed by small-angle X-ray scattering, vibrational spectroscopy, pulsed-field gradient NMR, and molecular dynamics simulations. This conformational transition triggers a collapse of the hydrogen-bonded water network and the emergence of densely packed ionic domains with confined water, producing a qualitative change in Li+ transport from solvent-mediated diffusion to network-confined hopping. Anion size and asymmetry systematically tune the onset of this transition, demonstrating that molecular geometry dictates mesoscale organization and dynamics in the ion-rich regime. Our results establish ion conformation, not merely composition or coordination, as a fundamental thermodynamic variable in concentrated solutions, providing a chemical framework that unifies solvation structure and transport in water-in-salt electrolytes and suggesting new principles for designing dense ionic media.

Nguyen, Huong TD↗

Solvent Polarity Effect on Chain Conformation, Film Morphology, and Optical Properties of a Water-Soluble Conjugated Polymer

The solvent polarity effect on chain conformation, film morphology, and photophysical properties of a nonionic water-soluble conjugated polymer (WSCP), poly[2,5-bis(diethylaminetetraethylene glycol)phenylene vinylene] (DEATG-PPV) is investigated in detail. The combination of stationary absorption and photoluminescence (PL) spectroscopy, time-resolved PL spectroscopy, and fluorescence correlation spectroscopy methods enables us to probe the chain conformation of DEATG-PPV, down to the level of a single chain when working with extremely diluted solutions. The use of correlated atomic force microscopy and confocal fluorescence lifetime imaging microscopy measurements of drop-casted DEATG-PPV films reveals the intrinsic relationship between chain conformation, film morphology, and optical properties. Depending on solvent polarity, DEATG-PPV presents extended, coiled, and collapsed chain conformations in solutions, which lead to distinct morphology and optical properties in solid films. Our work presents a pathway to control and characterize the film morphologies of WSCPs toward the optimal performance of various optoelectronic devices.

36 MATERIALS SCIENCE↗

Toward a simple molecular understanding of sum frequency generation at air-water interfaces

Second-order vibrational spectroscopies successfully isolate signals from interfaces, but they report on intermolecular structure in a complicated and indirect way. Here we adapt a perspective on vibrational response developed for bulk spectroscopies to explore the microscopic fluctuations to which sum frequency generation (SFG), a popular surface-specific measurement, is most sensitive. We focus exclusively on inhomogeneous broadening of spectral susceptibilities for OH stretching of HOD as a dilute solute in D{sub 2}O. Exploiting a simple connection between vibrational frequency shifts and an electric field variable, we identify several functions of molecular orientation whose averages govern SFG. The frequency-dependence of these quantities is well captured by a pair of averages, involving alignment of OH and OD bonds with the surface normal at corresponding values of the electric field. The approximate form we obtain for SFG susceptibility highlights a dramatic sensitivity to the way a simulated liquid slab is partitioned for calculating second-order response.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Superlattice Formation in Binary Mixtures of Block Copolymer Micelles

Two distinct diblock copolymers, poly(styrene-b-isoprene) (SI) and poly(styrene-b-dimethylsiloxane) (SD), were codissolved at various concentrations in the polystyrene selective solvent diethyl phthalate. Two SI diblocks, with block molar masses of 12000-33000 and 30000-33000, and two SD diblocks, with block molar masses of 19000-6000 and 16000-9000, were employed. The size ratio of the smaller SD micelles (S) to the larger SI micelles (L) varied from approximately 0.5 to 0.6, based on hydrodynamic radii determined by dynamic light scattering on dilute solutions containing only one polymer component. Due to incompatibility between the polyisoprene and polydimethylsiloxane blocks, a binary mixture of distinct SI and SD micelles was formed in each mixed solution, as confirmed by cryogenic transmission electron microscopy. When the total concentration of polymer was increased to 20--30%, the micelles adopted a superlattice structure. Small angle X-ray scattering revealed the lattice to be the full LS{sub 13} superlattice (space group Fm{sub 3}c) in all cases, with unit cell dimensions in excess of 145 nm. A coexistent face-centered cubic phase composed of SD micelles was also observed when the number ratio of S to L micelles was large.

36 MATERIALS SCIENCE↗

A Stepwise "Micellization-Crystallization" Route to Oblate Ellipsoidal, Cylindrical, and Bilayer Micelles with Polyethylene Cores in Water

Micellar polymorphism from block copolymers has been well documented, but most attention has focused on noncrystalline hydrophobic systems. We have investigated the micellization in water of model diblock copolymers with semicrystalline polyethylene (PE) as the core-forming component. Poly(N,N-dimethylacrylamide)–polyethylene (AE) diblock copolymers were synthesized by a combination of anionic and RAFT polymerizations. The bulk nanostructures were probed by small-angle X-ray scattering (SAXS) and AE diblock copolymers were found to be moderately segregated at 140 °C. Dispersions of AE amphiphiles in water were prepared by direct dissolution at 120 °C (i.e., above the melting transition of PE) followed by cooling to 25 °C. By manipulating the composition of AE diblock copolymers, discrete structures with oblate ellipsoidal, cylindrical, and bilayer morphologies were produced, as evidenced in cryogenic transmission electron microscopy (cryo-TEM). The self-assembled aggregates were also studied by small-angle neutron scattering (SANS) and dilute solution rheology. The semicrystalline nature of the nanostructures was further revealed by differential scanning calorimetry (DSC) and wide-angle X-ray scattering (WAXS). A stepwise “micellization–crystallization” process was proposed as the micelle formation mechanism, as supported by the existence of similar nanostructures at 120 °C using SANS. This strategy holds promise for a general protocol toward the production of giant wormlike micelles and vesicles with semicrystalline polymeric cores.

Yin, Ligeng↗

Building Conceptual Models of Field-Scale Uranium Reactive Transport in a Dynamic Vadose Zone-Aquifer-River System

Subsurface simulation is being used to build, test, and couple conceptual process models to better understand controls on a 0.4 km by 1.0 km uranium plume that has persisted above the drinking water standard in the groundwater of the Hanford 300 Area over the last 15 years. At this site, uranium-contaminated sediments in the vadose zone and aquifer are subject to significant variations in water levels and velocities driven by the diurnal, weekly, seasonal, and episodic Columbia River stage dynamics. Groundwater flow reversals typically occur twice a day with significant exchange of river water and groundwater in the near-river aquifer. Mixing of the dilute solution chemistry of the river with the groundwater complicates the uranium sorption behavior as the mobility of U(VI) has been shown experimentally to be a function of pH, carbonate, calcium, and uranium. Furthermore, uranium mass transfer between solid and aqueous phases has been observed to be rate-limited in the context of the high groundwater velocities resulting from the river stage fluctuations and the highly transmissive sediments (hydraulic conductivities ~1500 m/d). One- and two-dimensional vertical cross-sectional simulations of variably-saturated flow and reactive transport, based on laboratory-derived models of distributed rate mass transfer and equilibrium multicomponent surface complexation, are used to assess uranium transport at the dynamic vadose zone – aquifer interface as well as changes to uranium mobility due to incursions of river water into the aquifer.

54 ENVIRONMENTAL SCIENCES↗

Chirality-selected phase behaviour in ionic polypeptide complexes

In this study, polyelectrolyte complexes present new opportunities for self-assembled soft matter. Factors determining whether the phase of the complex is solid or liquid remain unclear. Ionic polypeptides enable examination of the effects of stereochemistry on complex formation. Here we demonstrate that chirality determines the state of polyelectrolyte complexes, formed from mixing dilute solutions of oppositely charged polypeptides, via a combination of electrostatic and hydrogen-bonding interactions. Fluid complexes occur when at least one of the polypeptides in the mixture is racemic, which disrupts backbone hydrogen-bonding networks. Pairs of purely chiral polypeptides, of any sense, form compact, fibrillar solids with a β-sheet structure. Analogous behaviour occurs in micelles formed from polypeptide block copolymers with polyethylene oxide, where assembly into aggregates with either solid or fluid cores, and eventually into ordered phases at high concentrations, is possible. Chirality is an exploitable tool for manipulating material properties in polyelectrolyte complexation.

36 MATERIALS SCIENCE↗