Search NASA⌕ Search

SEARCH · Search NASA

Results for “Dimensionless”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Crater modification by gravity - A mechanical analysis of slumping

An analysis of the stability of a crater from a mechanical point of view indicates that the observed slumping of lunar craters requires a perfectly plastic constitutive relation for the lunar surface rock. The angle of internal friction of this material must be less than a few degrees. The evidence for a perfectly plastic constitutive relation is described, and a simplified model of a crater in a perfectly plastic medium is used to investigate the nature of its collapse. Crater stability is found to depend principally upon a dimensionless parameter equal to the product of the density, acceleration of gravity, and depth divided by the yield strength. Criteria for stability, 'slope failures', and 'floor failures' are reported.

Melosh, H. J.↗
NASA NTRS1978

On the angular momentum loss of late-type stars

The observed surface angular velocity of main-sequence stars shows a sharp decrease at about spectral type F6. It is suggested that stars more massive than F6 cannot experience an appreciable angular-momentum loss because their convection zones cannot sustain a magnetic dynamo: without a magnetic field the angular-momentum loss is very small. The influence of rotation on the convective motions is essential for the existence of a solar-type dynamo. Rotation can influence these convective motions only if the typical convective time is larger than the rotation time. For main-sequence stars of different masses and chemical compositions the dimensionless parameter (convective velocity/sum's angular velocity times mixing length in the lower part of the convection zone) is evaluated. It is shown that this parameter increases very sharply for stars whose mass exceeds that defined by the relation log(star mass/solar mass) is of the order of 0.1. Thus even for large angular velocities, magnetic dynamos are not feasible if log(star mass/solar mass) appreciably exceeds 0.1.

Durney, B. R.↗
NASA NTRS1978

An experimental study of the influence of elevated buoyancy levels on flame spread rate over thermally thin cellulosic materials

The role of buoyancy on the flame spread rate over paper and its effect on extinction was studied by changing the gravity level and pressure. It was found that the flame spread rate decreases as the buoyancy induced flow increases. A method for correlating flame spread data using dimensionless parameters is presented. The Damkohler number is shown to be the dependent variable.

Shang, P. C.↗
NASA NTRS1978

Optimum reentry trajectories of a lifting vehicle

The optimum maneuver of a space shuttle vehicle reentering a spherical, stationary, and locally exponential atmosphere was investigated. The use of Chapman's modified variables and a rescaled lift-drag polar leads to the formulation of a set of dimensionless equations of motion for flight analysis. The resulting equations are exact in the sense that they are also valid for flight in the vacuum. For planar flight several typical optimum maneuvers are investigated at different altitude ranges, low, moderate and very high. For three-dimensional flight, the procedure to solve the optimum trajectory for maximum cross range is discussed. Finally, using the equilibrium glide condition the maximum cross ranges for entry from circular speed, for several values of E*, and the footprint for E* = 1.5 are computed in this reduced problem.

Chern, J. S.↗
NASA NTRS1979

Two-dimensional random surface model for asperity-contact in elastohydrodynamic lubrication

Relations for the asperity-contact time function during elastohydrodynamic lubrication of a ball bearing are presented. The analysis is based on a two-dimensional random surface model, and actual profile traces of the bearing surfaces are used as statistical sample records. The results of the analysis show that transition from 90 percent contact to 1 percent contact occurs within a dimensionless film thickness range of approximately four to five. This thickness ratio is several times large than reported in the literature where one-dimensional random surface models were used. It is shown that low pass filtering of the statistical records will bring agreement between the present results and those in the literature.

Coy, J. J.↗
NASA NTRS1978

Development program for a 200 kW, technological processes in space

Dimensionless conservation equations, are presented and the theoretical basis of fluid behavior aboard orbiting satellites are reviewed with application to the processes of manufacturing crystals in weightlessness. The small amount of gravitational acceleration is shown to increase the separation of bands of varying concentration. Natural convection is shown to have no practical effect on crystallization from realistic conductions of weightlessness. The effects of surface tension become increasingly large, and suggestions are made for further research.

Jory, H.↗
NASA NTRS1979

Theoretical bases for conducting certain technological processes in space

Dimensionless conservation equations are presented and the theoretical bases of fluid behavior aboard orbiting satellites with application to the processes of manufacturing crystals in weightlessness. The small amount of gravitational acceleration is shown to increase the separation of bands of varying concentration. Natural convection is shown to have no practical effect on crystallization from a liquid melt. Barodiffusion is also negligibly small in realistic conditions of weightlessness. The effects of surface tension become increasingly large, and suggestions are made for further research.

Okhotin, A. S.↗
NASA NTRS1979

Comparison of predicted and measured elastohydrodynamic film thickness in a 20-millimeter-bore ball bearing

Elastohydrodynamic film thicknesses were measured for a 20-mm bore ball bearing using the capacitance technique. The bearing was thrust loaded to 90, 445, and 778 N (20, 100, and 175 lb). The corresponding maximum contact stress on the inner race was 1.28, 2.09, and 2.45 GPa (185 000, 303,000, and 356, 000 psi). Test speeds ranged from 400 to 15,000 rpm. Measurements were taken with four different lubricants: (1) synthetic paraffinic; (2) synthetic paraffinic with additives; (3) synthetic type II aircraft oil; and (4) synthetic cycloaliphatic hydrocarbon traction fluid. The test bearing was mist lubricated. Test temperatures were 27, 65, and 121 C (80, 150, and 250 F). The measured results for the various test parameters were compared to theoretical predictions from computer programs. Also the data were plotted on dimensionless coordinates and compared to several classical isothermal theories.

Coy, J. J.↗
NASA NTRS1978

Remote sensing of environmental particulate pollutants - Optical methods for determinations of size distribution and complex refractive index

A unifying approach, based on a generalization of Pearson's differential equation of statistical theory, is proposed for both the representation of particulate size distribution and the interpretation of radiometric measurements in terms of this parameter. A single-parameter gamma-type distribution is introduced, and it is shown that inversion can only provide the dimensionless parameter, r/ab (where r = particle radius, a = effective radius, b = effective variance), at least when the distribution vanishes at both ends. The basic inversion problem in reconstructing the particle size distribution is analyzed, and the existing methods are reviewed (with emphasis on their capabilities) and classified. A two-step strategy is proposed for simultaneously determining the complex refractive index and reconstructing the size distribution of atmospheric particulates.

Fymat, A. L.↗
NASA NTRS1978

Elastohydrodynamic lubrication of elliptical contacts for materials of low elastic modulus. II - Starved conjunction

The study evaluates the effect of lubricant starvation on minimum film thickness in starved elliptical elastohydrodynamic conjunctions for materials of low elastic modulus. Lubricant starvation is studied simply by moving the inlet boundary closer to the center of the conjunction. A simple expression is presented for the dimensionless inlet boundary distance; this inlet boundary distance defines whether a fully flooded or a starved condition exists in the conjunction. A formula for the minimum film thickness under the starvation condition is derived. Contour plots of the pressure and film thickness in and around the contact are presented for both the fully flooded and starved lubrication conditions. It is shown that the inlet pressure contours become less circular and that the film thickness decreases substantially with increasing starvation severity.

Hamrock, B. J.↗
NASA NTRS1979

Design curves for non-linear analysis of simply-supported, uniformly-loaded rectangular plates

Design curves for the non-linear analysis of simply-supported rectangular plates subjected to uniform normal pressure loads have been developed. These curves yield the center deflection, center stress and corner stress in non-dimensionalized form plotted against a dimensionless parameter describing the load intensity. The results presented are based on extensive non-linear finite element analysis employing the ARGUS structural analysis program. Plates with length to width ratios of 1, 1.5, 2, 3 and 4 are included. The load range considered extends to 1000 times the load at which the behavior of the plate becomes significantly non-linear. Over the load range considered, the analysis shows that the ratio of center deflection to plate thickness for a square plate is less than 16 to 1, whereas linear theory would predict a center deflection 400 times the plate thickness. Likewise, the stress is markedly lower than would be predicted by linear theory. The present results are shown to be in excellent agreement with the classical linear theory up to a central deflection to plate thickness ratio of about one-half. In the non-linear regime the present results for deflection and stress are in very good agreement with the analytical and experimental work of other investigators.

Moore, D.↗
NASA NTRS1979

Implications of general covariance and maximum four-dimensional Yang-Mills gauge symmetry

General covariance and maximum four-dimensional Yang-Mills gauge symmetry lead to these results: (1) gravity is characterized by a dimensionless constant F of the order of 10 to the -19th; (2) the Newtonian force is always attractive; (3) space-time has a torsion; and (4) gravitational spin-force between two protons is about 10 to the 19th times stronger than the corresponding Newtonian force. A possible experimental test is discussed.

Hsu, J. P.↗
NASA NTRS1979

Peak Strouhal frequency of subsonic jet noise as a function of Reynolds number

The narrowband spectral characteristics of the acoustic field generated by subsonic jets at low Reynolds numbers were studied in terms of a dimensionless power spectral density. It was found that the variation of the sound magnitude of the spectrum is an increasing function of the Reynolds number. The maximum level of the spectrum is not a linear function of the Reynolds number. The spectra are insensitive to Reynolds number above a critical value of about 100,000. Up to Reynolds number of this magnitude, the peak Strouhal frequency observed at 30 deg emission angle is identical with that at 90 deg for any exit Mach number. At higher Reynolds number the peak Strouhal number increases with increasing emission angle. The peak Strouhal number was found to be about 0.2, which is in agreement with previous findings that a few discrete modes at a Strouhal number of around 0.2 in low Reynolds number supersonic jets are powerful noise generators.

Yamamoto, K.↗
NASA NTRS1979

Stability of inner planetary systems

The stability of inner planetary systems with arbitrary mass ratios is studied on the basis of the model of the plane restricted three-body problem. A quantitative stability criterion is obtained in terms of the difference between the critical value of the Jacobi constants (at which bifurcation can occur) and the critical value corresponding to a planetary orbit. An orbit is stable if it cannot leave a region that contains only the larger central body (Hill). For small values of the mass parameter, the maximum dimensionless radius of a Hill-stable orbit is 1 minus 2.4 times the cube root of the mass parameter.

Szebehely, V.↗
NASA NTRS1978

Morphometry of streamlined forms in terrestrial and Martian channels

Streamlined erosional forms in the Channeled Scabland are compared with streamline features recognized in the region of the Kasei Vallis on Mars shown in Viking imagery. The morphometric analysis considers three physical parameters, length, measured parallel to the suggested flow direction; width, taken as the maximum width of the streamlined form perpendicular to the flow direction; and area, measured with a grid placed over the surface. These parameters are used to calculate a dimensionless parameter k, defined as the square of the length multiplied by pi over four times the area. For the 137 Scabland forms studied k values range from 1.0 to 8.3 with an average of 3.2. The k values for 47 Martian streamlined forms range from 1.5 to 12.0 with an average of 3.8. The rough similarity of these results suggests that the terrestrial and Martian features were formed by similar processes. The forms appear to have developed an ideal shape, sufficiently elongated to reduce pressure drag in the fluid creating them, but not so long as to create excessive skin resistance.

Baker, V. R.↗
NASA NTRS1978

An investigation into the role of plastic failure in crater modification

The mechanical stability of an impact crater is analyzed in this paper via a quasi-static, axisymmetric slip line theory of plasticity. The yield model incorporated is Mohr-Coulomb and a simplified rectangular profile is used for the transient cavity. The degree of stability (or instability) is described as a function of internal friction angle, depth/diameter ratio, and a dimensionless parameter. To match the observed slumping of large lunar craters the cohesion strength of the lunar surface material must be low (less than 20 bars) and the angle of internal friction must be less than 2 deg. It is not implausible that these failure strength characteristics are realized by freshly shocked rock.

Mckinnon, W. B.↗
NASA NTRS1979

Two-dimensional random surface model for asperity-contact in elastohydrodynamic lubrication

Relations for the asperity-contact time fraction during elastohydrodynamic lubrication of a ball bearing are presented. The analysis is based on a two-dimensional random surface model, and actual profile traces of the bearing surfaces are used as statistical sample records. The results of the analysis show that transition from 90 percent contact to 1 percent contact occurs within a dimensionless film thickness range of approximately four to five. This thickness ratio is several times larger than reported in the literature where one-dimensional random surface models were used. It is shown that low pass filtering of the statistical records will bring agreement between the present results and those in the literature.

Coy, J. J.↗
NASA NTRS1979

Tidal interactions in the expanding universe - The formation of prolate systems

The study estimates the magnitude of the anisotropy that can be tidally induced in neighboring initially spherical protostructures, be they protogalaxies, protoclusters, or even uncollapsed density enhancements in the large-scale structure of the universe. It is shown that the linear analysis of tidal interactions developed by Peebles (1969) predicts that the anisotropy energy of a perturbation grows to first order in a small dimensionless parameter, whereas the net angular momentum acquired is of second order. A simple model is presented for the growth of anisotropy by tidal interactions during the nonlinear stage of the development of perturbations. A possible observational test is described of the alignment predicted by the model between the orientations of large-scale perturbations and the positions of neighboring density enhancements.

Binney, J.↗