Search NASA⌕ Search

SEARCH · Search NASA

Results for “Direct Entry”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Models for dynamic surface temperatures during rarefied aeropass maneuvers

New models for calculating dynamic surface temperatures in a direct simulation Monte Carlo particle method during atmospheric entry are described. The models take into account the radiative emissivity, thermal conductivity, and heat capacity of the material. They are applied to thin panels in a highly rarefied flows and yield the transient thermal response of individual surface facets. Simulation results for radiation panels with internal conductivity are verified by comparing them with free molecule theory.

Haas, Brian L.↗
NASA NTRS1980

Pioneer Venus Overview

A Pioneer Venus Overview is discussed. Pioneer Venus consists of two basic spacecraft: Orbiter and Multiprobe. The latter was separated into five separate vehicles near Venus. These were the probe transporter (called the Bus), a large atmospheric entry probe (dubbed Sounder) and three identical smaller probes (called North , Day, and Night in accordance with their entry locations). At Venus all six spacecraft communicated directly back to the Earth-based Deep Space Network (DSN) and, in the case of the Multiprobe mission, to two special receiving sites near Guam and Santiago (Chile). At the time this Special Issue was submitted for publication the nominal mission was complete and the Orbiter was continuing into an extended mission phase. It appears so that sufficient fuel remains to permit full operation through calendar year 1980, at least. The scientific payload, Principle Investigator, and his affiliation are listed for each Pioneer Venus spacecraft. This special issue is primarily devoted to short descriptions of the instruments listed with the exception of the Orbitor Cloud Photopolarimeter. Detailed instrument descriptions for this experiment have been published. Before proceeding with descriptions of the individual instruments, four special archival-type reports are included. The first deals with spacecraft design and operation. The Pioneer Venus spacecraft were unique and very special design features and operational modes needed to be incorporated. These are summarized therein. It should be noted that neither the scientific objectives nor the scientific results of the Pioneer Venus program are described or discussed in detail. The objectives have been published elsewhere.

Colin, Lawrence↗
NASA NTRS2004

The X-38 V-201 Flap Actuator Mechanism

The X-38 Crew Rescue Vehicle V-201 space flight test article was designed to achieve an aerodynamically controlled re-entry from orbit in part through the use of two body mounted flaps on the lower rear side. These flaps are actuated by an electromechanical system that is partially exposed to the re-entry environment. These actuators are of a novel configuration and are unique in their requirement to function while exposed to re-entry conditions. The authors are not aware of any other vehicle in which a major actuator system was required to function throughout the complete re-entry profile while parts of the actuator were directly exposed to the ambient environment.

Hagen, Jeff↗
NASA NTRS2004

Overview of the Aerothermodynamics Analysis Conducted in Support of the STS-107 Accident Investigation

A graphic presentation of the aerothermodynamics analysis conducted in support of the STS-107 accident investigation. Investigation efforts were conducted as part of an integrated AATS team (Aero, Aerothermal, Thermal, Stress) directed by OVEWG. Graphics presented are: STS-107 Entry trajectory and timeline (1st off-nominal event to Post-LOS); Indications from OI telemetry data; Aero/aerothermo/thermal analysis process; Selected STS-107 side fuselage/OMS pod off-nominal temperatures; Leading edge structural subsystem; Relevant forensics evidence; External aerothermal environments; STS-107 Pre-entry EOM3 heating profile; Surface heating and temperatures; Orbiter wing leading edge damage survey; Internal aerothermal environments; Orbiter wing CAD model; Aerodynamic flight reconstruction; Chronology of aerodynamic/aerothermoydynamic contributions; Acreage TPS tile damage; Larger OML perturbations; Missing RCC panel(s); Localized damage to RCC panel/missing T-seal; RCC breach with flow ingestion; and Aero-aerothermal closure. NAIT served as the interface between the CAIB and NASA investigation teams; and CAIB requests for study were addressed.

Campbell, Charles H.↗
NASA NTRS2010

Why Haven't Mars Rovers Landed Where They Were Expected to?

In a recent study (Desai, 2008) of the actual landing sites for the Mars Pathfinder, Mars Exploration Rovers and the Phoenix Mars Lander, data collected indicates that these missions landed at least 13 km downrange of their targeted landing sites. A direct reason is that density measurements taken during entry, descent and landing were consistently found to be lower than those predicted by Mars atmospheric models. The basis of this study is to further investigate this problem to see if certain aspects of current Mars atmospheric models need to be reevaluated. This study compared four different atmospheric profiles at nine pairs of comparable sites around Mars. The comparable sites are similar in location and Local True Solar Time; however they are from different Mars years. One year had normal conditions, while the other year experienced a global dust storm. Three of the atmospheric profiles were obtained by the Mars Global Surveyor (MGS); these data sets include a Radio Science profile and Thermal Emission Spectrometer data in limb and nadir projections. The three MGS data sets were selected from large observational databases to allow the sites to have data observed at nearcoincident times. The last atmospheric profile is from the Mars Global Reference Atmospheric Model (Mars-GRAM), an engineering level atmospheric model widely used for mission applications. Through careful data evaluation, several conclusions were drawn. Ratios among the data show that the three observed MGS profiles were consistent with each other, although they were recorded by three different methods. Mars-GRAM data had larger differences from the observed data. Mars-GRAM particularly had issues with consistently overestimating upper atmosphere atmospheric density, as noted in Desai s study. Differences between the observed atmospheric density profiles from the Mars-GRAM atmospheric density profile could be attributed to a temperature bias in the model, especially in the upper atmosphere.

Badger, Andrew M.↗
NASA NTRSDate not supplied

A Holistic DSMC Transport Database for Re-Entry and Ablation Modeling

Hybrid simulation frameworks combining Computational Fluid Dynamics (CFD) and Direct Simulation Monte Carlo (DSMC) are frequently employed to efficiently perform high-fidelity solutions of environments containing combined continuum/rarified flow. The use of DSMC, a stochastic, particle-based method, is necessary for high-Knudsen flow where continuum-based assumptions governing CFD break down. However, the DSMC methodology is generally very computationally inefficient to model the continuum regime. In a CFD/DSMC hybrid approach, obtaining an accurate, high-fidelity solution hinges on the consistent treatment of transport properties and the used thermo-chemical models employed within the two solvers. In principle, in regions where CFD and DSMC are both employed, the same gas mixture under the same conditions should have the same properties, regardless of simulation type. Observed differences should be due to non-equilibrium processes, rather than differences in physical models. While the transport models governing CFD and DSMC simulations are starkly different, they can effectively be linked via their use of reduced Chapman-Enskog collision integrals. In CFD, these integrals are typically stored as fitted polynomial expressions and used to directly compute gas transport properties via mixing rules or the full Chapman-Enskog formulation. In DSMC, they can be used to derive the collision parameters needed for the phenomenological collision cross-section models that govern particle interactions, via a Nelder-Mead optimization scheme. The goal of this work is to provide a unified DSMC transport database encompassing the vast majority of known gas species encountered during atmospheric entry, on Earth or any other Solar body. This goal is largely possible due to recently performed ab-initio quantum chemistry calculations. Combined with other high-fidelity literature sources, the planned database will consist of collision integral data for over 200 neutral and ionized species and over 17000 binary collisions. From these collision integrals, Nelder-Mead optimization is used to compute Variable Soft Sphere (VSS) collision model parameters for DSMC, fitted from 300 K to 20000 K. Initial comparisons of transport properties of relevant equilibrium gas mixtures show great agreement between CFD and DSMC-derived results. The completed database will be able to be readily applied to model binary collisions of any gas mixture containing the included species over the specified temperature range, making it a valuable tool for future planetary probe modeling efforts. An example is shown below. Equilibrium mixture transport properties for a 19-species Titan atmospheric model [4] are computed using both fitted VSS parameters and the original CFD collision integral values. Deviations in computed properties between the two approaches is less than 5% for the entire temperature range.

M R Gosma↗
NASA NTRS2008

STS-118 Radiator Impact Damage

During the August 2007 STS-118 mission to the International Space Station, a micro-meteoroid or orbital debris (MMOD) particle impacted and completely penetrated one of shuttle Endeavour s radiator panels and the underlying thermal control system (TCS) blanket, leaving deposits on (but no damage to) the payload bay door. While it is not unusual for shuttle orbiters to be impacted by small MMOD particles, the damage from this impact is larger than any previously seen on the shuttle radiator panels. A close-up photograph of the radiator impact entry hole is shown in Figure 1, and the location of the impact on Endeavour s left-side aft-most radiator panel is shown in Figure 2. The aft radiator panel is 0.5-inches thick and consists of 0.011 inch thick aluminum facesheets on the front and back of an aluminum honeycomb core. The front facesheet is additionally covered by a 0.005 inch thick layer of silver-Teflon thermal tape. The entry hole in the silver-Teflon tape measured 8.1 mm by 6.4 mm (0.32 inches by 0.25 inches). The entry hole in the outer facesheet measured 7.4 mm by 5.3 mm (0.29 inches by 0.21 inches) (0.23 inches). The impactor also perforated an existing 0.012 inch doubler that had been bonded over the facesheet to repair previous impact damage (an example that lightning can strike the same place twice, even for MMOD impact). The peeled-back edge around the entry hole, or lip , is a characteristic of many hypervelocity impacts. High velocity impact with the front facesheet fragmented the impacting particle and caused it to spread out into a debris cloud. The debris cloud caused considerable damage to the internal honeycomb core with 23 honeycomb cells over a region of 28 mm by 26 mm (1.1 inches by 1.0 inches) having either been completely destroyed or partially damaged. Figure 3 is a view of the exit hole in the rear facesheet, and partially shows the extent of the honeycomb core damage and clearly shows the jagged petaled exit hole through the backside facesheet. The rear facesheet exit hole damage including cracks in the facesheet measures 14 mm by 14 mm (0.55 inches by 0.55 inches). The remnants of the impacting particle and radiator panel material blown through the rear facesheet hole also created two penetrations in the TCS blanket 115 mm (4.5 inches) behind the rear facesheet. Figure 4 shows these two impacts, which are located 75 mm (3 inches) apart. Some deposits of material were found on the payload bay door beneath the TCS blanket, but no additional damage occurred to the door. Figure 5 illustrates the relationship of the facesheet entry hole to the TCS blanket damage, which may indicate the direction of the impacting particle. The image on the left side of Figure 5 shows an overhead view of the damaged radiator after the facesheet holes were cored out of the panel. The entry hole location and the two underlying TCS blanket damage sites are annotated on the image. Section A-A, running through the entry hole and TCS blanket damage locations, describes a 25 angle from the longitudinal axis of the shuttle. The 2nd impact angle can be seen in section A-A on the right side of Figure 5. An average 17 angle of impact to the surface normal was derived by measuring the angles of the two damage sites in TCS blanket to the entry hole.

Lear, Dana M.↗
NASA NTRS1972

Roll-modulated lifting entry optimization.

Equations of lifting entry are considered for fixed-angle-of-attack vehicular motion with path control for roll modulation of lift. Attention is directed to relocation and its consequences for the fixed-angle-of-attack atmospheric entry problem. Two reduced-order methods for working with the resulting system of equations are briefly examined. The methods are deemed to warrant further study.

Kelley, H. J.↗
NASA NTRS1973

Aerodynamic and flow-visualization studies of two delta-wing entry vehicles at a Mach number of 20.3

The longitudinal, lateral, and directional aerodynamic characteristics of two space shuttle concepts have been obtained in helium for operational flight Reynolds numbers at angles of attack from minus 10 to 55 deg. Included are elevon control deflections, roll control due to ailerons, and the effects of a nose modification. Selected results were compared with those derived from tangent-cone and Newtonian theories. Also included are results of a flow-visualization study consisting of electron-beam-illuminated flow and surface oil-flow patterns.

Arrington, J. P.↗
NASA NTRS2012

Entry, Descent, and Landing Communications for the 2011 Mars Science Laboratory

The Mars Science Laboratory (MSL), established as the most advanced rover to land on the surface of Mars to date, launched on November 26th, 2011 and arrived to the Martian Gale Crater during the night of August 5th, 2012 (PDT). MSL will investigate whether the landing region was ever suitable to support carbon-based life, and examine rocks, soil, and the atmosphere with a sophisticated suite of tools. This paper addresses the flight system requirement by which the vehicle transmitted indications of the following events using both X-band tones and UHF telemetry to allow identification of probable root causes should a mission anomaly have occurred: Heat-Rejection System (HRS) venting, completion of the cruise stage separation, turn to entry attitude, atmospheric deceleration, bank angle reversal commanded, parachute deployment, heatshield separation, radar ground acquisition, powered descent initiation, rover separation from the descent stage, and rover release. During Entry, Descent, and Landing (EDL), the flight system transmitted a UHF telemetry stream adequate to determine the state of the spacecraft (including the presence of faults) at 8 kbps initiating from cruise stage separation through at least one minute after positive indication of rover release on the surface of Mars. The flight system also transmitted X-band semaphore tones from Entry to Landing plus one minute although since MSL was occulted, as predicted, by Mars as seen from the Earth, Direct-To-Earth (DTE) communications were interrupted at approximately is approx. 5 min after Entry ( approximately 130 prior to Landing). The primary data return paths were through the Deep Space Network (DSN) for DTE and the existing Mars network of orbiting assets for UHF, which included the Mars Reconnaissance Orbiter (MRO), Mars Odyssey (ODY), and Mars Express (MEX) elements. These orbiters recorded the telemetry data stream and returned it back to Earth via the DSN. The paper also discusses the total power received during EDL and the robustness of the telecom design strategy used to ensure EDL communications coverage.

relay operations↗
NASA NTRS2019

Investigation of Direct Force Control for Planetary Aerocapture at Neptune

In this work, a direct force control numerical predictor-corrector guidance architecture is developed to enable Neptune aerocapture using flight-heritage blunt body aeroshells. A linear aerodynamics model is formulated for a Mars Science Laboratory-derived aeroshell. The application of calculus of variations shows that the optimal angle of attack and side-slip angle control laws are bang-bang. A closed-loop numerical predictor-corrector direct force control guidance algorithm is developed and numerically simulated using the Program to Optimize Simulated Trajectories II. The Monte Carlo simulated trajectories are demonstrated to be robust to the modeled dispersions in aerodynamics, atmospheric density, and entry state. An aerocapture technology trade study demonstrates that blunt body direct force control aerocapture enables similar performance as slender body bank angle control but halves the peak g-loading.

Deshmukh, Rohan G.↗
NASA NTRSDate not supplied

3D Material Response of the MSL Heatshield Using NuSil-Coated PICA

The Mars Science Laboratory (MSL) was protected during its atmospheric entry by an instrumented heatshield that used NASA's Phenolic Impregnated Carbon Ablator (PICA) material [1]. PICA is a lightweight carbon fiber/polymeric resin material that offers outstanding performance for protecting probes during planetary entry. Data from the Mars Entry Descent and Landing Instrument (MEDLI) suite on MSL offers unique in-flight validation data for models of material response and atmospheric entry. MEDLI recorded, among other things, time-resolved in-depth temperature data of PICA using thermocouple sensors assembled in the MEDLI Integrated Sensor Plugs (MISP) [2]. A space-grade silicone-based coating commercially known as NuSil CV-1144-0 [3] was applied to the entire MSL heatshield, including the MEDLI plugs, to mitigate the spread of dust from PICA. Modeling the thermal response of PICA-NuSil (PICA-N) system is still an open challenge. Ground testing of PICA-N models exhibited surface temperature jumps of the order of 150 K due to oxide scale formation and sub-sequent NuSil burn-off. It is therefore critical to include a validated model for the material response of the coating in engineering codes. A test campaign has been conducted at the NASA’s Langley HyMETS [4] facility to screen the response of PICA-N and gather detailed data on its behavior [5]. A first model of PICA-N thermal response has been developed using the Hy-METS experiments [6]. The objective of this work is to analyze the material response of the latest PICA-N model compared to the engineering model used to simulate the entry of MSL. The environment and material response around the MSL aeroshell during Mars atmospheric entry is simulated using a collection of tools. The Direct Simulation Monte Carlo SPARTA code [7] is used in the rarefied regime, the Data Parallel Line Relaxation (DPLR) code [8] is used in the continuum regime and radiative heating conditions are provided by the Nonequilibrium air radiation (NEQAIR) code [9] to estimate the environmental conditions. The thermal response inside the material is computed using the Porous material Analysis Toolbox based on Open-FOAM (PATO) [10,11,12]. Thermodynamic and chemistry properties are estimated using the Mutation++ library [13]. The approach implemented in PATO as a first cut PICA-N thermal response model is outlined in Figure 1. While the recession is less than the coating thickness, the Surface mass and energy balance Boundary Condition (SBC) uses the NuSil B’ tables. Once the recession removes the coating, the usual PICA B’ tables are used for the SBC. The B’ tables are computed using an equilibrium solver implemented in Mutation++, given the temperature, pressure, blowing rate, composition of the pyrolysis and environment gases, and the condensed species at the surface. Preliminary results of the 3D material response of the MSL heat-shield at the peak heating (80 sec after Entry Interface) are shown in Figure 2. Current NASA’s mission to Mars, Mars 2020, used the spare heatshield of MSL for thermal protection during entry, descent, and landing. In preparation for Mars 2020 post-flight analysis, the PATO high-fidelity material response capability was benchmarked against flight data from MEDLI. This effort represents an important milestone toward the development of validated predictive capabilities for designing thermal protection systems for planetary probes. This bench-marking is awaiting the final release of the MEDLI-2 data.

Aerospace↗
NASA NTRS1972

Magnetospheric access of solar particles and the configuration of the distant geomagnetic field, volume 1

The access of 1.2 to 40 MeV protons and 0.4 to 1.0 MeV electrons from interplanetary space to the polar cap regions was investigated with an experiment on board a low altitude, polar-orbiting satellite (0G0 4). A total of 333 quiet time observations of the electron polar cap boundary give a mapping of the boundary between open and closed geomagnetic field lines. Observations of events associated with co-rotating regions of enhanced proton flux in interplanetary space were used to establish the characteristics of the 1.2 to 40 MeV proton access windows. The results were compared to particle access predictions of the distant geomagnetic tail configurations. The role played by interplanetary anisotropies in the observation of persistent polar cap features is discussed. Special emphasis is given to the problem of nonadiabatic particle entry through regions where the magnetic field is changing direction.

Evans, L. C.↗
NASA NTRS1978

Low surface pressure models for Titan's atmosphere

The inversion model for the atmosphere of Titan is reviewed. The basic features of the model are: a cold surface (80 K), a warm stratosphere (160 K) and a low surface pressure (20 mbar). The model is consistent with all existing thermal infrared spectrophotometry, but it cannot preclude the existence of an opaque, cloud, thick atmosphere. The model excludes other gases than methane as bulk constituents. Radio wavelengths observations, including recent data from the very large array, are discussed. These long wavelength observations may be the only direct means of sampling the surface environment before an entry probe or flyby.

Caldwell, J.↗
NASA NTRS1979

Dayside merging and cusp geometry

Geometrical considerations are presented to show that dayside magnetic merging when constrained to act only where the fields are antiparallel results in lines of merging that converge at the polar cusps. An important consequence of this geometry is that no accelerated flows are predicted across the dayside magnetopause. Acceleration owing to merging acts in opposition to the magnetosheath flow at the merging point and produces the variably directed, slower-than-magnetosheath flows observed in the entry layer. Another consequence of the merging geometry is that much of the time closed field lines constitute the subsolar region of the magnetopause. The manner in which the polar cap convection patterns predicted by the proposed geometry change as the interplanetary field is rotated through 360 deg provides a unifying description of how the observed single circular vortex and the crescent-shaped double vortex patterns mutually evolve under the influence of a single operating principle.

Crooker, N. U.↗
NASA NTRS2007

The Spatial Variation of Polar Rain Electrons and its Cause

It is generally accepted that field aligned electrons in the solar wind can follow field lines connected to Earth and precipitate in the polar ionosphere where they are known as polar rain. Few-hundred eV, field-aligned electrons of the solar wind "strahl" carry the interplanetary heat flux moving out from the sun and these electrons precipitate in either the northern or southern hemisphere depending on the magnetic field direction. These electrons produce enhanced polar rain in one hemisphere or the other although weaker polar rain is usually produced in the opposite hemisphere by whatever electrons are moving in the opposite direction. Although much evidence exists for this simple free entry mechanism, it has also long been known that there are spatial variations in the energies and intensities of the precipitating electrons. The present work compares electron distribution functions measured by the ACE spacecraft in the solar wind with those measured by the DMSP spacecraft at 800 km altitude over the polar cap. It is found that shifting the DMSP distribution functions in energy by amounts ranging from 10's to a few hundred eV produces quite good agreement with simultaneous ACE measurements. Over most of the polar cap this DMSP energy shift must be positive to achieve this agreement, suggesting the electrons have been decelerated by a field aligned potential as they move from the solar wind to low altitudes. The largest shifts occur on the nightside and on the dawn or dusk side, with the latter depending on the plasma convection pattern which is controlled by the orientation of the IMF. Nearer the cusp the shift is smaller or even negative. Since more massive tailward flowing magnetosheath ions are unable io follow the field lines into the magnetotail like the electrons, a field aligned potential is expected to develop to exclude low energy electrons and prevent an excessive charge imbalance. Such a potential would also produce the deceleration of those electrons that reach low altitudes. This improved understanding of polar rain should increase the utility of polar rain measurements as a diagnostic of the magnetosphere magnetic field configuration.

Fairfield, D. H.↗
DOE OSTI2026

Topographic effects on reflected acoustic waves from the OSIRIS-REx reentry observed from stratospheric balloons

During long-distance sound propagation in planetary atmospheres, acoustic waves may reflect off the air/surface interface one or more times. For low sound frequencies and flat interfaces, the incident and reflected wave tend to be nearly identical. However, this may not be the case when the downgoing acoustic wave encounters topography. Here, we describe a set of direct and reflected acoustic signals recorded on free-flying balloons during the hypersonic entry of the OSIRIS-REx sample return capsule (SRC). In two of the three cases presented here, an impulsive reflected arrival similar in form to the direct sonic boom of the SRC is observed, followed by a diffuse coda. In contrast, one of the floating stations lacked an impulsive reflection entirely, with only the coda present. We use full waveform modeling to show how reflection in the presence of complex topography can explain coda seen in all three examples as well as the lack of impulsive arrival on the third. Our results indicate that the complex signals often observed in long range acoustic propagation could be due, in part, to interactions with topography during transmission.

Lees, Jonathan M. [University of North Carolina, C↗
NASA NTRS2005

Communications Blackout Predictions for Atmospheric Entry of Mars Science Laboratory

The Mars Science Laboratory (MSL) is expected to be a long-range, long-duration science laboratory rover on the Martian surface. MSL will provide a significant milestone that paves the way for future landed missions to Mars. NASA is studying options to launch MSL as early as 2009. MSL will be the first mission to demonstrate the new technology of 'smart landers', which include precision landing and hazard avoidance in order to -land at scientifically interesting sites that would otherwise be unreachable. There are three elements to the spacecraft; carrier (cruise stage), entry vehicle, and rover. The rover will have an X-band direct-to-Earth (DTE) link as well as a UHF proximity link. There is also a possibility of an X-band proximity link. Given the importance of collecting critical event telemetry data during atmospheric entry, it is important to understand the ability of a signal link to be maintained, especially during the period near peak convective heating. The received telemetry during entry (or played back later) will allow for the performance of the Entry-Descent-Landing technologies to be assessed. These technologies include guided entry for precision landing, hazard avoidance, a new sky-crane landing system and powered descent. MSL will undergo an entry profile that may result in a potential communications blackout caused by ionized plasma for short periods near peak heating. The vehicle will use UHF and possibly X-band during the entry phase. The purpose of this report is to quantify or bound the likelihood of any such blackout at UHF frequencies (401 MHz) and X-band frequencies (8.4 GHz). Two entry trajectory scenarios were evaluated: a stressful entry trajectory to quantify an upper-bound for any possible blackout period, and a nominal likely trajectory to quantify likelihood of blackout for such cases.

UHF↗