Search NASA⌕ Search

SEARCH · Search NASA

Results for “Ductile fracture”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Mechanical testing of PH13-8Mo H950 Steel for Xue-Wierzbicki Fracture Criterion Determination at 20° C and -40° C

Mechanical testing was conducted to collect the data needed to build a Xue-Wierzbicki (XW) fracture model for PH13-8 Mo H950 stainless steel (PH 13-8 SS). This model is intended for use in structural analysis of this material between room temperature and -40° C. Tests were performed on four different specimen geometries such that a range of stress states were characterized at room temperature and -40° C. Tensile tests on R5 tensile specimens were also performed to assess material anisotropy. Fracture toughness test were also conducted. The fracture toughness of this material at -40° C was 68% of the room-temperature value. Material strength generally increased with decreasing temperature while the opposite trend was observed for ductility. These trends were most pronounced for specimens with the largest stress triaxialities.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Mechanical behavior of carbonated MgO-based Engineered Cementitious Composite (ECC) after high temperatures exposure

Carbonated MgO-based Engineered Cementitious Composite (ECC) has ultrahigh tensile ductility and tight crack width control behavior. However, the expectation of improved fire-resistant has not been confirmed. This study explored the alterations to mechanical and microstructure characteristics of this material after exposure to temperatures up to 500 °C. Material mass loss, compressive strength, tensile strength, strain capacity, and matrix fracture toughness were measured. Scanning electron microscopy, mercury intrusion porosimetry, thermogravimetric analysis, and X-ray diffraction were used to probe the degradation of the cement matrix and fibers. The effect of elevated temperature on carbonated MgO-based ECC was further assessed via examination of the micromechanical behavior of the fiber-matrix. The objective of this research was to assess the performance of carbonated MgO-based ECC exposed to fire hazards. The tensile ductility of carbonated MgO-based ECC was found to be enhanced when exposed to ~100 °C as compared with those at room temperature ~20 °C. Further increase in exposure temperature, however, posed a negative impact on the composite compressive strength, ultimate tensile strength, and ability to control crack width. Here the results provide a useful database for further investigations into carbonated MgO-based ECC for fire safety enhancement.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Preliminary Study of Potential Utilization of Triassic Rift Basins for Long-Term Carbon Sequestration

Triassic rift basins of the eastern United States present a potential option for long–term carbon dioxide (CO 2 ) sequestration. Exposed and buried basins are located near large point CO 2 sources. Because of their similar origins, comparable fill successions indicate a level of reproducibility that can be conveyed between basins. The thick rock successions of the exposed Culpeper and Gettysburg basins served as proxies for understanding of the basin sequences. Their study allowed recognition of five mappable assemblages of rock types, herein termed lithofacies associations. These lithofacies associations were formed by alluvial fan, braided and meandering streams and marginal and distal lake depositional processes.Stratigraphic architecture of the lithofacies associations within exposed basins suggests a vertical succession that consists of an initial coarse-grained fluvial succession that is progressively replaced upward and basinward by finer grained lacustrine deposits. Along the faulted margins of the basins alluvial fans transitioning to fluvial delta deposits reflect lateral progradation and contemporaneous lateral components of the basin filling.To test the model devised in exposed basins, facies associations were developed for the buried Taylorsville Basin. This basin preserves over 8,000 feet of Triassic rocks that are concealed beneath more than 2,000 feet of Cretaceous and Tertiary Coastal Plain sediments. Composition and stratigraphic architecture of these rocks are similar to those observed in exposed basins. Infilling of the basin was the result of vertical aggradation and lateral progradation of coarse-grained to fine-grained facies. Based upon study of outcrops in the Culpeper and Gettysburg basins, groups of recurring lithologic facies were identified as the fundamental constructs of the basin’s sediment infilling. These groups of facies, termed lithofacies associations, represent an amalgamation of lithologic components from broadly similar depositional systems. These lithologic associations were then extrapolated into the exposed and buried portions of the Taylorsville basins. This effort determined that Triassic rift basins provide several avenues for potential study of geologic sequestration of carbon. The characteristic rift basin succession in the basins presents possible reservoir targets within the marginal fluvial deposits. Furthermore, intrusive and extrusive mafic bodies present a potential source of fracture porosity that could serve as CO 2 reservoirs. Porosity values from thin section analysis of exposed basin samples are higher in alluvial fan and braided fluvial lithofacies. Porosity is highest in samples that show less compaction, due to a lack of ductile lithic fragments and/or higher stratigraphic position. Log data from the Taylorsville Basin indicates that porosity and permeability values in basin marginal fluvial strata are elevated. Near the center of the basin, porosity and permeability values are greatly reduced, primarily owing to the fine-grained character of the lacustrine deposits. Some Triassic basins also contain thick intervals of concordant extrusive and intrusive mafic igneous rocks. These igneous bodies are potential CO 2 reservoirs for several reasons. Firstly, extrusive lava flows provide potential storage in the layers of primary porosity that occur in the vesicules formed at the top of lava flows. Secondly, both lava flows and subsurface igneous sills exhibit extensive fracture porosity produced by the rapid cooling of the flows and intrusions. Thirdly, these igneous rocks are mafic in composition, and studies have shown that iron- and magnesium-rich mafic rocks provide sequestration opportunities through carbonate remineralization. Lastly, extrusive and intrusive igneous rocks are invariably preserved within fine-grained lake deposits. These lacustrine sediments can serve as a fine-grained confining layer that encases the igneous rocks both above and below.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2023

LDRD 22A1059-068FP Tailoring the Properties of Multi-Phase Materials Through the Use of Correlative Microscopy and Machine Learning - Poster

High strength alloys with good ductility, hardness, and toughness are needed to meet stringent design requirements for extreme environments. One complication in this pursuit is the evidence that metals rarely exhibit both high strength and good fracture toughness as the underlying mechanisms work in opposition. An exception to this behavior is found in multiphase alloys that form complex microstructures of mixed phases with variable grain sizes and shapes that provide increased fracture toughness by the arrangement of their constituent elements. We propose to explore this phenomenon using state-of-the-art machine learning (ML) techniques in a new and novel manner to identify and correlate the critical microstructural features in a Titanium-10Vanadium-2Iron-3Aluminum (Ti-10V-2Fe-3Al) alloy that is reported to exhibit high strength and fracture toughness. Additionally, we will employ multiple, complementary characterization techniques such as optical microscopy, electron backscatter diffraction (EBSD), energy dispersive spectroscopy (EDS) and scanning electron microscopy to provide multi-layer, quantitative ground truth measures of the microstructures. This data will be used to train a Convolutional Neural Network (CNN) in a semi-supervised environment to identify key microstructural features such as ? platelet dimensions and locations and ?/? phase boundaries and correlate those features with the strength and toughness. Here the ? and ? nomenclature refers to hexagonal close pack (hcp) and body center cubic (bcc) crystal structures, respectively. Previous work has focused on popular alloys and typically used one characterization technique. This research is focused on a promising titanium alloy, uses multiple complimentary characterization tools to provide precise microstructural information and correlates to improved fracture toughness. The resulting ML tool can be trained for additional microstructural features, different alloy(s), and or target mechanical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2025

A Multiscale Approach to Simulate Non‐Isothermal Multiphase Flow in Deformable Porous Materials

Coupled thermal, hydraulic, and mechanical processes in porous materials play important roles in several energy and environmental technologies. The Darcy-Brinkman-Biot (DBB) framework has proven effective in modeling multiphase fluid flow in deformable porous solids across both pore and Darcy scales, including in systems where fractures coexist with a porous matrix. In this study, we extend the DBB framework, originally designed for isothermal conditions, to address non-isothermal problems by incorporating an energy conservation equation. The resulting solver, hybridBiotThermalInterFoam, enables simulations of coupled multiphase fluid flow, heat transfer, and solid deformation in hybrid-scale systems containing both solid-free regions and ductile porous domains. The new solver is validated through comparisons with analytical solutions and, also, against established heat transfer solvers chtMultiRegionFoam and compressibleInterFoam. Further, a series of 2D and 3D case studies, including two-phase heat transfer in solid-free, static, or deformable porous media, highlights the solver's capacity to simulate complex flow dynamics and heat transport in systems involving high mobility ratios, viscous fingering, and fracture propagation. Our results establish the feasibility of incorporating thermal effects in simulations of a wide variety of energy geotechnics and environmental applications, including enhanced hydrocarbon recovery, soil remediation, and enhanced geothermal energy systems.

04 OIL SHALES AND TAR SANDS↗
DOE OSTI2021

Mechanical Performance and Mesostructure Analysis of Proton-Irradiated Fused Filament Fabrication Acrylonitrile Butadiene Styrene Material

The use of fused filament fabrication (FFF) acrylonitrile butadiene styrene (ABS) and other thermoplastics in radiation environments is beginning to be studied as possible replacements for traditionally manufactured parts and tools. Interlayer adhesion within the mesostructure has been shown in published literature to be an integral component in the strength of FFF ABS. Research of irradiated 3D printed polymers has primarily focused on the influence of gamma irradiation on the mechanical properties of FFF ABS samples, without evaluating its impact on the mesostructure of the samples. The purpose of this paper is to understand the mechanical damage caused by proton radiation on FFF ABS samples through the evaluation of the mesostructure of the ABS samples. To achieve this objective, proton radiation at 40 MeV was applied to FFF ABS samples at radiation doses up to 1.0 MGy at a dose rate of 1 MGy/hr. Following the irradiation, tensile testing was performed on the samples. Here, the fractured surfaces of the tested samples were subsequently observed using a scanning electron microscope. The mechanical test results show an increase in the ultimate tensile strength (UTS) and a decrease in the ductility of the irradiated samples. Statistical analysis on the results shows that there is a statistically significant difference in the UTS and the ductility of unirradiated and 1.0 MGy irradiated samples and between irradiated samples and 1.0 MGy samples. In addition, the percentage elongation at break has statistically significant differences in the means between irradiated samples and 1.0 MGy samples. The UTS has statistically significant differences in the means between 0.1 MGy and 1.0 MGy. The difference in the means between the unirradiated and the 1.0 MGy samples is the most significant for both the UTS and elongation at break. The scanning electron microscopy (SEM) results indicated that interlayer adhesion improved as a function of radiation dose corresponding to the increase in tensile strength. The SEM results also showed that crazing and plastic deformation were reduced; aligning with the loss in ductility observed in the tensile tests results. The proton radiation is causing these mechanical and physical changes through two mechanisms: (1) dose rate effects on ionizing radiation-induced oxidative degradation; and (2) radiation heating effects of high energy (>1 MeV) charged particles.

electron microscopy↗
DOE OSTI2023

Novel refractory high-entropy metal-ceramic composites with superior mechanical properties

A new concept of refractory high-entropy metal-ceramic composites (HEMCC) has been proposed that combines the outstanding physical properties of both high-entropy alloy (HEA) and high-entropy ceramic (HEC). As the first HEMCC system, to the best of our knowledge, TiTaNbZr-(TiTaNbZr)C, has been developed by a powder metallurgy process. The HEA and HEC phases exhibit body-centered cubic (BCC) and rock-salt B1 crystal structures, respectively, and both phases have non-equimolar chemical compositions. Further, with the increase of the HEC phase in HEMCC, the hardness is enhanced while the density and fracture toughness are decreased. HEA50C sintered from 50vol% HEA and 50vol% HEC precursor powders shows a favorable combination of flexural strength (541±48MPa) and fracture toughness (6.93±0.27 MPa·m 1/2 ) at room temperature and a high compressive strength at 1300ºC (275MPa). The optimized mechanical performance of HEMCC might be attributed to the combination of the ductile HEA and strong HEC phases, smaller grain size, and crack arrest at HEC/HEA interfaces.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Microstructural Characteristics, Mechanical Properties, and Corrosion Behavior of Field-Assisted Diffusion Welded Alloy 617

This study investigated the microstructural characteristics, mechanical response, and corrosion resistance of Alloy 617 diffusion welded by electric field-assisted sintering (EFAS). The microstructure exhibited good grain boundary (GB) migration across the interface and flat interface in the samples bonded at different conditions. Graded grain size was observed, with grain coarsening being more significant near sample surface due to EFAS-induced temperature gradient. Tensile testing revealed that the specimens fractured in the matrix away from the interface. The peak strength of 807 MPa was obtained in the samples welded at 1000°C. The materials obtained at 1100°C exhibited reduced tensile strength but improved ductility. Strain maps revealed by digital image correlation showed the flat interfaces were less ductile compared to the matrix. The hardness reduced near sample surfaces due to enlarged grains induced by temperature gradient. The interfaces with GB migration exhibited improved corrosion resistance in molten salt compared to the flat interfaces.

36 - MATERIALS SCIENCE↗
DOE OSTI2023

Toughening Brittle Bio‐P3HB with Synthetic P3HB of Engineered Stereomicrostructures

Abstract Poly(3‐hydroxybutyrate) (P3HB), a biologically produced, biodegradable natural polyester, exhibits excellent thermal and barrier properties but suffers from mechanical brittleness, largely limiting its applications. Here we report a mono‐material product design strategy to toughen stereoperfect, brittle bio or synthetic P3HB by blending it with stereomicrostructurally engineered P3HB. Through tacticity ([ mm ] from 0 to 100 %) and molecular weight ( M n to 788 kDa) tuning, high‐performance synthetic P3HB materials with tensile strength to ≈30 MPa, fracture strain to ≈800 %, and toughness to 126 MJ m −3 (>110× tougher than bio‐P3HB) have been produced. Physical blending of the brittle P3HB with such P3HB in 10 to 90 wt % dramatically enhances its ductility from ≈5 % to 95–450 % and optical clarity from 19 % to 85 % visible light transmittance while maintaining desirably high elastic modulus (>1 GPa), tensile strength (>35 MPa), and melting temperature (160–170 °C). This P3HB‐toughening‐P3HB methodology departs from the traditional approach of incorporating chemically distinct components to toughen P3HB, which hinders chemical or mechanical recycling, highlighting the potential of the mono‐material product design solely based on biodegradable P3HB to deliver P3HB materials with diverse performance properties.

Zhang, Zhen↗
DOE OSTI2023

Toughening Brittle Bio‐P3HB with Synthetic P3HB of Engineered Stereomicrostructures

Abstract Poly(3‐hydroxybutyrate) (P3HB), a biologically produced, biodegradable natural polyester, exhibits excellent thermal and barrier properties but suffers from mechanical brittleness, largely limiting its applications. Here we report a mono‐material product design strategy to toughen stereoperfect, brittle bio or synthetic P3HB by blending it with stereomicrostructurally engineered P3HB. Through tacticity ([ mm ] from 0 to 100 %) and molecular weight ( M n to 788 kDa) tuning, high‐performance synthetic P3HB materials with tensile strength to ≈30 MPa, fracture strain to ≈800 %, and toughness to 126 MJ m −3 (>110× tougher than bio‐P3HB) have been produced. Physical blending of the brittle P3HB with such P3HB in 10 to 90 wt % dramatically enhances its ductility from ≈5 % to 95–450 % and optical clarity from 19 % to 85 % visible light transmittance while maintaining desirably high elastic modulus (>1 GPa), tensile strength (>35 MPa), and melting temperature (160–170 °C). This P3HB‐toughening‐P3HB methodology departs from the traditional approach of incorporating chemically distinct components to toughen P3HB, which hinders chemical or mechanical recycling, highlighting the potential of the mono‐material product design solely based on biodegradable P3HB to deliver P3HB materials with diverse performance properties.

Chemistry↗
DOE OSTI2023

From Well Log to Formation Model: A Novel Laboratory Calibrated Methodology with Demonstration

This work demonstrates how the characterization and modeling of both elastic and creep properties are essential to describe zones in layered rock formations as either low-stress targets for stimulation or high-stress barriers to fracture growth. Prediction of fracture height is critical for designing stimulation operations in oil and gas wells. Ideally, fractures are placed in target zones which will produce hydrocarbons and should not propagate into zones expected to be unproductive or to produce unwanted fluids such as water which in turn must be treated and/or disposed. The essential task in designing stimulation plans is predicting which zones have low horizontal stresses and which will be high-stress barriers to fracture growth. Despite this importance, there are gaps in current knowledge and a complete workflow from laboratory characterization to a finite element model which includes time dependent rock deformation is required. While the research and methodology presented here also have application to CO 2or hydrogen storage, wastewater injection, and geothermal applications, the focus will be on hydrocarbon extraction. This thesis presents the results of a characterization-to-prediction workflow for the Caney shale, which is an emerging hydrocarbon resource in Oklahoma, USA. It begins with an investigation to enable critical evaluation of the Caney zonation into nominally “brittle” and “ductile” zones based on properties observed from well logs. It shows none of the zones are consistently “brittle” or “ductile” mechanical behavior based on the variety of definitions of these terms. However, the nominally ductile zones are weaker and more prone to creep. A laboratory investigation of samples including strength, elastic, and creep properties, is then used in a finite element model of stress evolution. The model includes both elastic deformation and viscoplastic creep. Results predict the least creep-prone layers to have the lowest horizontal stresses, therefore comprising hydraulic fracturing targets. The most creep-prone layers attain a horizontal stress similar to the vertical stress and therefore are predicted to be high stress barriers to hydraulic fracture stimulation. In addition to defining stimulation target intervals, the model shows how as tectonic strain rate increases, there is a transition from creep-dominated stresses to stresses dominated by elasticity.

Benge, Margaret↗
DOE OSTI2023

Achieving High Strength and Creep Resistance in Inconel 740H Superalloy through Wire-Arc Additive Manufacturing and Thermodynamic-Guided Heat Treatment

Inconel 740H superalloy is commonly used in advanced ultra-supercritical power plants since it possesses excellent strength and creep resistance. This study investigates the microstructure and mechanical properties of Inconel 740H superalloy fabricated using wire-arc additive manufacturing. The as-printed microstructure consisted of columnar γ grains with the Laves phase and (Nb, Ti)C carbides as secondary phases. The anisotropy in grain structure increased from the bottom to the top regions, while the hardness was highest in the middle portion of the build. To guide the post-heat treatment design, thermodynamic and kinetic simulations were employed to predict the temperature and time. Complete recrystallization with the Laves phase dissolution occurred throughout the build after homogenization at 1200 °C for 2 h. The peak hardness was achieved after aging at 760 °C for 12 h with the M 23 C 6 carbides decorating the grain boundaries and γ’ precipitates in the grain interior. The yield strength (655 MPa) and ductility (29.5%) in the post-heat treated condition exceeded the design targets (620 MPa, 20%). Stress rupture tests at 750 °C showed that the high-temperature performance was at par with the wrought counterparts. The fracture mode after rupture was identified to be intergranular with the presence of grain boundary cavities along with grain boundary sliding.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Microstructure and strengthening of Al-6Ce-3Ni-0.7Fe (wt%) alloy manufactured by laser powder-bed fusion

In this study, an Al-6Ce-3Ni-0.7Fe (wt%) alloy was fabricated via laser powder-bed fusion and its microstructure, thermal stability, tensile properties, and creep properties are investigated for two rapid-solidification rates with different eutectic spacings. For both faster- and slower-cooled states, the as-fabricated alloy mostly shows elongated grains with very fine eutectic networks (~40 nm lamellar width) comprising a high-volume fraction (~18 %) of intermetallic phases. Faster-cooled samples, however, display a less continuous eutectic network with finer spacing (~100 nm), leading to higher Orowan strengthening and therefore superior microhardness and yield stress up to ~350 °C. Upon aging (300 - 450 °C), micron-size Al 9 (Ni,Fe) 2 needle-like precipitates form within grains, and the Al 11 Ce 3 eutectic network spheroidizes, while retaining a submicron width and spacing, resulting in 33–37 % drop in microhardness after 144 h aging at 400 °C. Limited tensile ductility (~6 %) and creep ductility (~1-2 %) are measured for both faster- and slower-cooled alloys due to an inhomogeneous microstructure, where cavitation preferentially initiates at melt-pool boundaries, precipitate-free zones, and/or denuded zones, eventually leading to local fracture. Denuded zones, induced by stress, form due to diffusional flow with stress-dependent orientations, and are identified as microstructurally weak regions leading to strain localization. The present alloy does not show a significant difference in 300 °C creep resistance between: (i) tensile and compressive loading, (ii) faster- and slower-cooled samples, and (iii) continuous and spheroidized eutectics. Creep resistance at 300 °C is comparable to that of a Ce-richer Al-10.5Ce-3.1Ni-1.2Mn (wt%) alloy, despite the formation of denuded zones and needle-like Al 9 (Ni,Fe) 2 precipitates.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Simulation and analysis of the 3D double shock-induced recompression of spall using a hybrid PAGOSA with FLIP+MPM

In this work, an innovative hybrid algorithm PAGOSA with FLIP + MPM is first presented by coupling PAGOSA with the particle FLIP + MPM, and applied to systematically exploring the 3D recompression of spall induced by double-shock waves in ductile materials as the few existing studies are currently limited to the pure longitudinal recompression of spall, and ignore the 3D effects. This algorithm solves the difficulties the grid-based methods encounter when applied to capturing the fracture in material. We first validate the capabilities of PAGOSA with FLIP + MPM to predict different fracture/fragmentation cases by solving two benchmark problems and comparing with the analytical solutions or the experiment results. The convergences and the infinity-norm errors are also investigated. Subsequently, the 3D effects are demonstrated by simulating the spallation in material using PAGOSA with FLIP + MPM and comparing with those in the longitudinal cases. Additionally, some factors that affect the spallation with 3D effects are also discussed. Finally, the recompressions of spall in material with/without 3D effects are systematically simulated and analyzed. The recompression of spall driven by a high explosive is also simulated to show the ability of PAGOSA with FLIP + MPM to handle this kind of problem. The conditions that can lead to a recompression of spall are explored. Also, numerical results show that PAGOSA with FLIP + MPM can accurately predict different fracture cases, that the 3D effects play an important role in fracture/fragmentation, and the recompression of spall is very sensitive to the occurrence conditions, shows great differences when considering 3D effects in real applications. Moreover, the present hybrid method can be easily extended to other grid-based techniques employed for fracture in materials.

3D effects↗
DOE OSTI2022

Resolving the Martensitic Transformation in Q&P Steels In-Situ at Dynamic Strain Rates Using Synchrotron X-ray Diffraction

Herein the dynamic deformation response of two quenching and partitioning (Q&P) steels was investigated using a high strain rate tension pressure bar and in-situ synchrotron radiography and diffraction. This allowed for concurrent measurements of the martensitic transformation, the elastic strains/stresses on the martensite and ferrite, and the bulk mechanical behavior. The steel with the greater fraction of ferrite exhibited greater ductility and lower strength, suggesting that dislocation slip in ferrite enhanced the deformability. Meanwhile, the kinetics of the martensitic transformation appeared similar for both steels, although the steel with a greater ferrite fraction retained more austenite in the neck after fracture.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Structural and mechanical properties of magnesium aluminate nanoceramics under high pressure

Nanoceramics may have different structural and physical properties compared to their coarse-grained counterparts. Here, we report the high-pressure study of micro- and nano-crystalline MgAl2O4 in order to examine the effect of particle size on the structural stability. A reversible pressure-induced phase transition (cubic to tetragonal) is observed in MgAl2O4 nanocrystals under non-hydrostatic pressure at room temperature, in contrast to the previously reported structural transition of MgAl2O4 at high pressure and high temperature. It is also found that the compressed MgAl2O4 microcrystals do not fracture further below 60 nm, suggesting a plastic deformation mechanism transition. MgAl2O4 with a grain size above ∼60 nm exhibits normal cracking behaviors, but shows metal-like plastic deformation behaviors below this critical size. It is implied that combined ductility and strength can be achieved in nanoceramic MgAl2O4.

Xu, Jianing (ORCID:0000000325474344)↗
DOE OSTI2020

Effect of microstructural and environmental variables on ductility of austenitic stainless steels

Austenitic stainless steels are used extensively in harsh environments, including for high-pressure gaseous hydrogen service. However, the tensile ductility of this class of materials is very sensitive to materials and environmental variables. While tensile ductility is generally insufficient to qualify a material for hydrogen service, ductility is an effective tool to explore microstructural and environmental variables and their effects on hydrogen susceptibility, to inform understanding of the mechanisms of hydrogen effects in metals, and to provide insight to microstructural variables that may improve relative performance. In this study, hydrogen precharging was used to simulate high-pressure hydrogen environments to evaluate hydrogen effects on tensile properties. Several austenitic stainless steels were considered, including both metastable and stable alloys. Room temperature and subambient temperature tensile properties were evaluated with three different internal hydrogen contents for type 304L and 316L austenitic stainless steels and one hydrogen content for XM-11. Significant ductility loss was observed for both metastable and stable alloys, suggesting the stability of the austenitic phase is not sufficient to characterize the effects of hydrogen. Internal hydrogen does influence the character of deformation, which drives local damage accumulation and ultimately fracture for both metastable and stable alloys. While a quantitative description of hydrogen-assisted fracture in austenitic stainless steels remains elusive, these observations underscore the importance of the hydrogen-defect interactions and the accumulation of damage at deformation length scales.

36 MATERIALS SCIENCE↗