SEARCH · Search NASA

Results for “Dynamic Stability Derivatives”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

All sources NASA NTRS DOE OSTI

NASA NTRS2012

Flexible Launch Vehicle Stability Analysis Using Steady and Unsteady Computational Fluid Dynamics

Launch vehicles frequently experience a reduced stability margin through the transonic Mach number range. This reduced stability margin can be caused by the aerodynamic undamping one of the lower-frequency flexible or rigid body modes. Analysis of the behavior of a flexible vehicle is routinely performed with quasi-steady aerodynamic line loads derived from steady rigid aerodynamics. However, a quasi-steady aeroelastic stability analysis can be unconservative at the critical Mach numbers, where experiment or unsteady computational aeroelastic analysis show a reduced or even negative aerodynamic damping.Amethod of enhancing the quasi-steady aeroelastic stability analysis of a launch vehicle with unsteady aerodynamics is developed that uses unsteady computational fluid dynamics to compute the response of selected lower-frequency modes. The response is contained in a time history of the vehicle line loads. A proper orthogonal decomposition of the unsteady aerodynamic line-load response is used to reduce the scale of data volume and system identification is used to derive the aerodynamic stiffness, damping, and mass matrices. The results are compared with the damping and frequency computed from unsteady computational aeroelasticity and from a quasi-steady analysis. The results show that incorporating unsteady aerodynamics in this way brings the enhanced quasi-steady aeroelastic stability analysis into close agreement with the unsteady computational aeroelastic results.

Bartels, Robert E.↗

NASA NTRS1977

Calculated Hovering Helicopter Flight Dynamics with a Circulation Controlled Rotor

The influence of the rotor blowing coefficient on the calculated roots of the longitudinal and lateral motion was examined for a range of values of the rotor lift and the blade flap frequency. The control characteristics of a helicopter with a circulation controlled rotor are discussed. The principal effect of the blowing is a reduction in the rotor speed stability derivative. Above a critical level of blowing coefficient, which depends on the flap frequency and rotor lift, negative speed stability is produced and the dynamic characteristics of the helicopter are radically altered.

Johnson, W.↗

NASA NTRS1979

Lightman-Eardley instabilities and accretion disk thickening

After reviewing the role of Compton scattering in accretion disks around black holes, it is discussed whether Lightman-Eardley (LE) secular instabilities can trigger and maintain Pringle-Rees (PR) thermal instabilities. The radiative-transfer-equation and equation-of-state criteria for LE stability in alpha-viscosity-law disk models and dynamic viscosity criteria for more general situations is derived. On the basis of these considerations the LE instability is insufficient for inducing PR instabilities and hot thick inner regions important in accretion-disk models of compact hard X-ray sources. The density thinning due to radial velocity gradients in the accretion flow is suggested as a more likely and satisfactory mechanism.

Stoeger, W. R.↗

NASA NTRS1994

Control of the SCOLE configuration using distributed parameter models

A continuum model for the SCOLE configuration has been derived using transfer matrices. Controller designs for distributed parameter systems have been analyzed. Pole-assignment controller design is considered easy to implement but stability is not guaranteed. An explicit transfer function of dynamic controllers has been obtained and no model reduction is required before the controller is realized. One specific LQG controller for continuum models had been derived, but other optimal controllers for more general performances need to be studied.

Hsiao, Min-Hung↗

DOE OSTI2024

Bridging 20 Years of Soil Organic Matter Frameworks: Empirical Support, Model Representation, and Next Steps

Abstract In the past few decades, there has been an evolution in our understanding of soil organic matter (SOM) dynamics from one of inherent biochemical recalcitrance to one deriving from plant‐microbe‐mineral interactions. This shift in understanding has been driven, in part, by influential conceptual frameworks which put forth hypotheses about SOM dynamics. Here, we summarize several focal conceptual frameworks and derive from them six controls related to SOM formation, (de)stabilization, and loss. These include: (a) physical inaccessibility; (b) organo‐mineral and ‐metal stabilization; (c) biodegradability of plant inputs; (d) abiotic environmental factors; (e) biochemical reactivity and diversity; and (f) microbial physiology and morphology. We then review the empirical evidence for these controls, their model representation, and outstanding knowledge gaps. We find relatively strong empirical support and model representation of abiotic environmental factors but disparities between data and models for biochemical reactivity and diversity, organo‐mineral and ‐metal stabilization, and biodegradability of plant inputs, particularly with respect to SOM destabilization for the latter two controls. More empirical research on physical inaccessibility and microbial physiology and morphology is needed to deepen our understanding of these critical SOM controls and improve their model representation. The SOM controls are highly interactive and also present some inconsistencies which may be reconciled by considering methodological limitations or temporal and spatial variation. Future conceptual frameworks must simultaneously refine our understanding of these six SOM controls at various spatial and temporal scales and within a hierarchical structure, while incorporating emerging insights. This will advance our ability to accurately predict SOM dynamics.

54 ENVIRONMENTAL SCIENCES↗

NASA NTRS1992

Assured crew return vehicle post landing configuration design and test

The 1991-1992 senior Mechanical and Aerospace Engineering Design class continued work on the post landing configurations for the Assured Crew Return Vehicle (ACRV) and the Emergency Egress Couch (EEC). The ACRV will be permanently docked to Space Station Freedom fulfilling NASA's commitment of Assured Crew Return Capability in the event of an accident or illness aboard Space Station Freedom. The EEC provides medical support and a transportation surface for an incapacitated crew member. The objective of the projects was to give the ACRV Project Office data to feed into their feasibility studies. Four design teams were given the task of developing models with dynamically and geometrically scaled characteristics. Groups one and two combined efforts to design a one-fifth scale model for the Apollo Command Module derivative, an on-board flotation system, and a lift attachment point system. This model was designed to test the feasibility of a rigid flotation and stabilization system and to determine the dynamics associated with lifting the vehicle during retrieval. However, due to priorities, it was not built. Group three designed a one-fifth scale model of the Johnson Space Center (JSC) benchmark configuration, the Station Crew Return Alternative Module (SCRAM) with a lift attachment point system. This model helped to determine the flotation and lifting characteristics of the SCRAM configuration. Group four designed a full scale EEC with changeable geometric and geometric and dynamic characteristics. This model provided data on the geometric characteristics of the EEC and on the placement of the CG and moment of inertia. It also gave the helicopter rescue personnel direct input to the feasibility study. Section 1 describes in detail the design of a one-fifth scale model of the Apollo Command Module Derivative (ACMD) ACRV. The objective of the ACMD Configuration Model Team was to use geometric and dynamic constraints to design a one-fifth scale working model of the Apollo Command Module Derivative (ACMD) configuration with a Lift Attachment Point (LAP) System. This model was required to incorporate a rigidly mounted flotation system and the egress system designed the previous academic year. The LAP system was to be used to determine the dynamic effects of locating the lifting points at different locations on the vehicle. The team was then to build and test the model; however, due to priorities, this did not occur. To better simulate the ACMD after a water landing, the nose cone section was removed and the deck area exposed. The areas researched during the design process were construction, center of gravity and moment of inertia, and lift attachment points.

Source record↗

NASA NTRSDate not supplied

TPSAS-NF1676L-15194-DND

Technical Motivation - 1950s: Indication of large lateral (roll/yaw) acceleration (“β-dot”) dynamic derivatives for configurations with strong vortex flows in the stall region (Lichtenstein, Campbell, Riley)! - 1960s: Increased emphasis on use of long-range missiles tempered by aircraft losses in close-in air combat - 1970s: - Effect of lateral acceleration derivatives on aircraft stability (Nguyen) - Characteristics and air combat advantages of rapid controlled large-amplitude maneuvering at low speeds near maximum lift shown in piloted simulations (Herbst) - 1980s: - Dynamic (forced-oscillation, rotary balance, curved- and rolling-flow) wind tunnel tests (Grafton, Lutze, Hultberg) - Incorporation of test data into computer simulations (Kalviste) - Technologies developed for controlled maneuvers at stall, post-stall angles of attack - Concern that conventional math modeling inadequately represented the dynamic component of these motions - Need to evaluate dependency of control laws on accurate computer simulations and motion prediction

Marilyn E Ogburn↗

NASA NTRS1972

Dynamic Nonlinear Elastic Stability of Helicopter Rotor Blades in Hover and in Forward Flight

Equations for large coupled flap-lag motion of hingeless elastic helicopter blades are consistently derived. Only torsionally-rigid blades excited by quasi-steady aerodynamic loads are considered. The nonlinear equations of motion in the time and space variables are reduced to a system of coupled nonlinear ordinary differential equations with periodic coefficients, using Galerkin's method for the space variables. The nonlinearities present in the equations are those arising from the inclusion of moderately large deflections in the inertia and aerodynamic loading terms. The resulting system of nonlinear equations has been solved, using an asymptotic expansion procedure in multiple time scales. The stability boundaries, amplitudes of nonlinear response, and conditions for existence of limit cycles are obtained analytically. Thus, the different roles played by the forcing function, parametric excitation, and nonlinear coupling in affecting the solution can be easily identified, and the basic physical mechanism of coupled flap-lag response becomes clear. The effect of forward flight is obtained with the requirement of trimmed flight at fixed values of the thrust coefficient.

Friedmann, P.↗

NASA NTRS1993

An analytic modeling and system identification study of rotor/fuselage dynamics at hover

A combination of analytic modeling and system identification methods have been used to develop an improved dynamic model describing the response of articulated rotor helicopters to control inputs. A high-order linearized model of coupled rotor/body dynamics including flap and lag degrees of freedom and inflow dynamics with literal coefficients is compared to flight test data from single rotor helicopters in the near hover trim condition. The identification problem was formulated using the maximum likelihood function in the time domain. The dynamic model with literal coefficients was used to generate the model states, and the model was parametrized in terms of physical constants of the aircraft rather than the stability derivatives resulting in a significant reduction in the number of quantities to be identified. The likelihood function was optimized using the genetic algorithm approach. This method proved highly effective in producing an estimated model from flight test data which included coupled fuselage/rotor dynamics. Using this approach it has been shown that blade flexibility is a significant contributing factor to the discrepancies between theory and experiment shown in previous studies. Addition of flexible modes, properly incorporating the constraint due to the lag dampers, results in excellent agreement between flight test and theory, especially in the high frequency range.

Hong, Steven W.↗

NASA NTRS1993

An analytic modeling and system identification study of rotor/fuselage dynamics at hover

A combination of analytic modeling and system identification methods have been used to develop an improved dynamic model describing the response of articulated rotor helicopters to control inputs. A high-order linearized model of coupled rotor/body dynamics including flap and lag degrees of freedom and inflow dynamics with literal coefficients is compared to flight test data from single rotor helicopters in the near hover trim condition. The identification problem was formulated using the maximum likelihood function in the time domain. The dynamic model with literal coefficients was used to generate the model states, and the model was parametrized in terms of physical constants of the aircraft rather than the stability derivatives, resulting in a significant reduction in the number of quantities to be identified. The likelihood function was optimized using the genetic algorithm approach. This method proved highly effective in producing an estimated model from flight test data which included coupled fuselage/rotor dynamics. Using this approach it has been shown that blade flexibility is a significant contributing factor to the discrepancies between theory and experiment shown in previous studies. Addition of flexible modes, properly incorporating the constraint due to the lag dampers, results in excellent agreement between flight test and theory, especially in the high frequency range.

Hong, Steven W.↗

NASA NTRS1979

Important factors in the maximum likelihood analysis of flight test maneuvers

The information presented is based on the experience in the past 12 years at the NASA Dryden Flight Research Center of estimating stability and control derivatives from over 3500 maneuvers from 32 aircraft. The overall approach to the analysis of dynamic flight test data is outlined. General requirements for data and instrumentation are discussed and several examples of the types of problems that may be encountered are presented.

Iliff, K. W.↗

NASA NTRS1991

The application of cost averaging techniques to robust control of the benchmark problem

A method is presented for the synthesis of robust controllers for linear time invariant systems with parameterized uncertainty structures. The method involves minimizing the average quadratic (H2) cost over the parameterized system. Bonded average cost implies stability over the set of systems. The average cost functional is minimized to derive robust fixed-order dynamic compensators. The robustness properties of these controllers are demonstrated on the sample problem.

Hagood, Nesbitt W.↗

NASA NTRS1992

Derivation and application of hard deadlines for real-time control systems

The computation-time delay in the feedback controller of a real-time control system may cause failure to update the control input during one or more sampling periods. If this delay exceeds a certain limit called a hard deadline, either the necessary conditions for system stability are violated or the system leaves the allowed state-space. In such a case a dynamic failure is said to occur to the system. A method for calculating the hard deadlines in linear time-invariant control systems by considering system stability and the allowed state-space is presented. To derive necessary conditions for (asymptotic) system stability, the state difference equation is modified based on an assumed maximum delay and the probability distribution of delays whose magnitudes are less than, or equal to, the assumed maximum delay. Moreover, the allowed state-space - which is derived from given input and state constraints - is used to calculate the hard deadline as a function of time and the system state. A one-shot delay model in which a single event causes a dynamic failure is also considered. The knowledge of hard deadline is then applied to the design of error recovery in a triple modular redundant (TMR) controller computer.

Shin, Kang G.↗

NASA NTRS1979

Calculated hovering helicopter flight dynamics with a circulation-controlled rotor

The flight dynamics of a hovering helicopter with a circulation-controlled rotor are analyzed. The influence of the rotor blowing coefficient on the calculated eigenvalues of the helicopter motion is examined for a range of values of the rotor lift and the blade flap frequency. The control characteristics of a helicopter with a circulation-controlled rotor are discussed. The principal effect of the blowing is a reduction in the rotor speed stability derivative. Above a critical level of blowing coefficient, which depends on the flap frequency and rotor lift, negative speed stability is produced and the dynamic characteristics of the helicopter are radically altered. The handling qualities of a helicopter with negative speed stability are probably unacceptable without a stability augmentation system.

Johnson, W.↗

NASA NTRS2013

Dependence of Dynamic Modeling Accuracy on Sensor Measurements, Mass Properties, and Aircraft Geometry

The NASA Generic Transport Model (GTM) nonlinear simulation was used to investigate the effects of errors in sensor measurements, mass properties, and aircraft geometry on the accuracy of identified parameters in mathematical models describing the flight dynamics and determined from flight data. Measurements from a typical flight condition and system identification maneuver were systematically and progressively deteriorated by introducing noise, resolution errors, and bias errors. The data were then used to estimate nondimensional stability and control derivatives within a Monte Carlo simulation. Based on these results, recommendations are provided for maximum allowable errors in sensor measurements, mass properties, and aircraft geometry to achieve desired levels of dynamic modeling accuracy. Results using additional flight conditions and parameter estimation methods, as well as a nonlinear flight simulation of the General Dynamics F-16 aircraft, were compared with these recommendations

Grauer, Jared A.↗

NASA NTRS1973

Relativistic stellar stability - An empirical approach.

A quantitative measure is derived of the extent to which solar-system experiments imply the existence of the dynamical relativistic instabilities in stars. The Parametrized Post-Newtonian (PPN) framework of Will and Nordtvedt (1972) is used in the derivation. The PPN framework is a post-Newtonian theory of gravity with adjustable parameters. It is shown that for conservative theories of gravity current experimental limits on the PPN parameters guarantee the existence of the dynamical relativistic instability in stars.

Ni, W.-T.↗

NASA NTRS2018

Dynamic Modeling using Output-Error Parameter Estimation based on Frequency Responses Estimated with Multisine Inputs

A method is developed for estimating model parameters, such as nondimensional stability and control derivatives, by fitting transfer function or state-space models to empirical frequency response data using the output-error approach. The frequency response data were computed using Fourier transforms of measured input and output data. The control surfaces were excited with periodic multisine inputs which facilitated time-ecient estimation of multiple-input multiple-output frequency responses. The method was applied to lateral data from a nonlinear flight dynamics simulation of the F-16 aircraft, and to longitudinal data from multiple repeated flight test maneuvers of the NASA T-2 subscale aircraft. Results using simulation data showed the frequency response method compared well to other standard methods for parameter estimation. In addition to including all the available inputs, outputs, and harmonic frequencies in the estimation, relatively small subsets of the measured data could also be used to focus on identifying specific parts of the model. Results from flight test data showed that parameter estimates and uncertainties determined from repeated maneuvers were accurate and in statistical agreement with each other.

Grauer, Jared A.↗

NASA NTRS1987

High speed, precision motion strategies for lightweight structures

Abstracts of published papers and dissertations generated during the reporting period are compiled. Work on fine motion control was completed. Specifically, real time control of flexible manipulator vibrations were experimentally investigated. A linear model based on the application of Lagrangian dynamics to a rigid body mode and a series of separable flexible modes was examined with respect to model order requirements, and modal candidate selection. State feedback control laws were implemented based upon linear quadratic regulator design. Specification of the closed loop poles in the regulator design process was obtained by inclusion of a prescribed degree of stability in the manipulator model. Work on gross motion planning and control is also summarized. A systematic method to symbolically derive the full nonlinear dynamic equations of motion of multi-link flexible manipulators was developed.

Book, Wayne J.↗