SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
An algorithm is presented for performing accurate, high-speed, floating-point function generation for univariate functions defined at arbitrary breakpoints. Rapid identification of the breakpoint interval, which includes the input argument, is shown to be the key operation in the algorithm. A hardware implementation which makes extensive use of read/write memories is used to illustrate the algorithm.
Tool fits out-of-round seal groove and laps it to fine finish without binding. Includes floating lapping pieces riding freely in groove, and are curved to match nominal diameter of groove. One lapping piece tightened so it does not move relative to disk.
The energy-stability theory has been used to study the stability properties of thermocapillary convection in a half-zone model of the float-zone crystal-growth process. It is concluded that the energy theory provides a sufficient condition for stability to disturbances of arbitrary amplitude. Results of the computation of energy-stability limits are found to be in good agreement with experimentally measured bounds for oscillatory thermocapillary convection.
Energy-stability theory has been applied to investigate the stability properties of thermocapillary convection in a half-zone model of the float-zone crystal-growth process. An earlier axisymmetric model has been extended to permit nonaxisymmetric disturbances, thus determining sufficient conditions for stability to disturbances of arbitrary amplitude. The results for nonaxisymmetric disturbances are compared with earlier axisymmetric results, with linear-stability results for a geometry with an infinitely long aspect ratio and with stability boundaries from recent laboratory experiments.
The floating point arithmetics implemented in the Cray 2 and Cray Y-MP computer systems are nearly identical, but large scale computations performed on the two systems have exhibited significant differences in accuracy. The difference in accuracy is analyzed for Cholesky factorization algorithm, and it is found that the source of the difference is the subtract magnitude operation of the Cray Y-MP. The results from numerical experiments for a range of problem sizes are presented, and an efficient method for improving the accuracy of the factorization obtained on the Y-MP is presented.
Computer simulation was conducted to study a modified floating-zone crystal growth process, in which the melt surface is mostly covered with a heated ring. The growth of 6-mm diameter single crystals of NaNO3 was considered, and the effects of the following parameters were studied: (1) temperature of the ring, (2) growth rate, (3) surface tension-temperature coefficient of the melt, (4) thermal expansion coefficient of the melt, and (5) gravity. It was demonstrated that thermocapillary convection in the melt zone is reduced significantly in this modified process. The model was checked against the measured lengths of the meniscus near the growth front and axial temperature distribution in a growing crystal, and the agreement was good.
The interaction between a space system and the space environment has been one of the driving questions for the design of spacecraft since the dawn of the space age. The Space Station Freedom will represent a significant increase in spacecraft size, power, and activity relative to spacecraft that are currently in orbit. The structure floating potential on Space Station Freedom is studied with simple analytical models of the current collection. The probability of arcing due to dielectric breakdown is assessed.
Tests were conducted to investigate the possibility of a serious accident arising from unintentional contact with the water in substantially horizontal flight at high speed. Referring to vector diagrams on Figure 2, it will be seen that a very dangerous condition may arise if the float be allowed to come in contact with the water at high speeds as, for example, when flying at high speed just above the water. The initial diving moment due to suction and drag combined may be great enough to cause the seaplane to nose under before the pilot is able to control the motion. The same test data indicate clearly the existence of forces and moments tending to produce the phenomenon observed by Mr. Carroll (Technical Note No. 287) when the maneuver is carried out at lower speeds, as in a landing.
This report describes preliminary wind tunnel tests on a model of a monoplane wing equipped with wing tip floating ailerons. Lift and drag, as well as rolling and yawing moments, were measured.
This report is the fourth of a series on systematic tests conducted which compares lateral control devices with particular reference to their effectiveness at high angles of attack. The present report covers tests with floating tip ailerons on rectangular Clark y wings. Ailerons of two profiles were tested - symmetrical and Clark y, both with adjustable trailing-edge flaps. Each form was tested at three hinge-axis locations, both with and without vertical end plates between the ailerons and the wing proper. The results from these tests are compared with the results from tests on a wing of the same over-all size equipped with average-sized ordinary ailerons.
Providing information that will make possible a favorable compromise between landing impact and planing resistance is the immediate problem in experimental float development. A description of equipment to perform dropping tests are included as well as how to determine the landing impact.
This paper presents the characteristics of floats submitted to the test committee and the tests performed on them.
For the purpose of solving all the problems involved, an investigation was made with flat, rectangular planing surfaces. The investigation of a flat, rectangular planing surface, which can be considered as the portion of a flat float bottom lying in front of the step, has the advantage that the frictional resistance can be determined directly from the test results. Normal and tangential forces act on the lower side of the planing surface towed through still water, while the upper side and the lateral edges are under constant atmospheric pressure.
Floating zone methods have potential applications in growing single high-quality semi-conductor crystals. In this method, melts can be sustained without containers and, therefore, are free from contamination from the containers. The main objective of this project is to use the Image Furnace to study a large diameter, (20 mm) single crystal of InSb under microgravity conditions. The behavior of the liquid column is recorded on the VTR tapes and is compared with what is expected theoretically. The single crystal grown in space is characterized by comparing it with single crystals grown on the ground with respect to crystallographic and electronic properties. The goal of this project is to confirm the effects of the microgravity on the single crystals.
An architecture to evaluate a 24-bit floating-point sum or difference of products using modified sequential carry-save multipliers with extensive pipelining is described. The basic building block of the architecture is a carry-save multiplier with built-in mantissa alignment for the summation during the multiplication cycles. A carry-save adder, capable of mantissa alignment, correctly positions products with the current carry-save sum. Carry propagation in individual multipliers is avoided and is only required once to produce the final result.
The ANSI/IEEE Standard 854-1987 for floating-point arithmetic is interpreted by converting the lexical descriptions in the standard into mathematical conditional descriptions organized in tables. The standard is represented in higher-order logic within the framework of the HOL (Higher Order Logic) system. The paper is divided in two parts with the first part the interpretation and the second part the description in HOL.
This report describes how a laser-heated floating zone apparatus can be used to investigate single-crystal fibers of various compositions. A feedrod with a stoichiometric composition of high-purity powders was connected to a pedestal and fed into a laser scan where it combined with a single-crystal fiber seed. A molten zone was formed at this junction. As the feedrod was continuously fed into the laser scan, a single-crystal fiber of a prescribed orientation was withdrawn from the melt. The resultant fibers, whose diameters ranged from 100 to 250 gm, could then be evaluated on the basis of their growth behavior, physical properties, mechanical properties, and fiber perfection.
Experimental complementary metal-oxide/semiconductor (CMOS) active-pixel image sensor integrated circuit features simple floating-gate structure, with metal-oxide/semiconductor field-effect transistor (MOSFET) as active circuit element in each pixel. Provides flexibility of readout modes, no kTC noise, and relatively simple structure suitable for high-density arrays. Features desirable for "smart sensor" applications.