Search NASA⌕ Search

SEARCH · Search NASA

Results for “FLOW - CHANNELS, CURVED”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1966

The Properties of Flowing Sheets Formed by Impingement of Liquid Jets on Curved Surfaces

An applied research program was conducted to determine the properties of flat sheets of propellants formed by directing jets of liquid tangentially against concave, cylindrical deflector surfaces. The dimensions and spatial orientation of the resultant sheets were found to depend only on the orifice diameter and deflector geometry for three propellant simulants of widely-varying physical properties, over the range of injection velocities encountered in liquid rocket engines. Correlating equations, suitable for use in injector design, are presented for free-sheet width and spreading angle. Distribution of mass and velocity across the free-flowing sheets is also reported. Conditions were discovered under which true sheets do not form, or at best malformed or pulsating sheets result. An envelope of geometrical constraints for deflector design is tentatively defined in order to avoid these undesirable operating regions. The results of the present cold-flow tests are compared with firing test data for impinging-sheet injectors and combustion performance is related to single sheet behavior.

Riebling, Robert W.↗
NASA NTRS1977

An experimental investigation of a three-dimensional wall jet

An experimental investigation of the effects of a curved and flat wall surface on the flow development of an axisymmetric jet exhausting into a moving airstream has been made. Of primary concern was the comparison of the one-point statistical properties of the unconfined jet to the quantities measured in the flows over a flat plate and a curved wall surface. Quantities measured in this investigation included mean velocities in all three directions, turbulent intensities, autocorrelations, power spectral densities, and intermittencies. The investigation was confined to the near field of the turbulent jet. The curved wall (flap) was found to have a very large effect on both the mean velocity and the turbulent velocity components of the flowfield. The potential core region of the jet was found to break up most rapidly for the flow over the flap. A laser-Doppler velocimeter, using a phase locked-loop processor, was used to make the desired velocity field measurements. To determine the intermittency profiles, a laser light scattering technique was employed.

Catalano, G. D.↗
NASA NTRS1991

Basic studies of baroclinic flows

Computations were completed of transition curves in the conventional annulus, including hysteresis effect. The model GEOSIM was used to compute the transition between axisymmetric flow and baroclinic wave flow in the conventional annulus experiments. Thorough testing and documentation of the GEOSIM code were also completed. The Spacelab 3 results from the Geophysical Fluid Flow Cell (GFFC) were reviewed and numerical modeling was performed of many of the cases with horizontal temperature gradients as well as heating from below, with different rates of rotation. A numerical study of the lower transition to axisymmetric flow in the baroclinic annulus was performed using GEOSIM.

Miller, Tim L.↗
NASA NTRS1951

Generalization of turbojet and turbine-propeller engine performance in windmilling condition

Windmilling characteristics of several turbojet and turbine-propeller engines were investigated individually over a wide range of flight conditions in the NACA Lewis altitude wind tunnel. A study was made of all these data and windmilling performance of gas turbine engines was generalized. Although internal-drag, air-flow, and total-pressure-drop parameters were generalized to a single curve for both the axial-flow type engines and another for the centrifugal-flow engine. The engine speed, component pressure changes, and windmilling-propeller drag were generalized to single curves for the two turbine-propeller-type engines investigated. By the use of these curves the windmilling performance can be estimated for axial-flow type gas turbine engines similar to the types investigated over a wide range of flight conditions.

Wallner, Ewis E↗
DOE OSTI2022

June 2022 Permeability Measurements in P-Tunnel, Nevada National Security Site

This document describes gas permeability measurements made in June 2022 in P-Tunnel at the Nevada National Security Site (NNSS). Four boreholes (AC-1, GI-5, GI-6, and HF-1) were tested with a dual packer system. The pressure versus flow rate data that were collected are analyzed using a numerical simulation method that captures compressible gas flow in partially saturated porous media using a close approximation to the geometry of the test setup. The first part of this document begins with data collection and a description of the packer assembly followed by details on data acquisition, measurement instrumentation, and equipment followed by a description of pre-test system verification. Next, the implementation of testing in the field is described, including how specific locations were chosen for testing. The second part of this document describes the numerical simulations used to back-out permeability from the pressure versus flow rate data. First, the numerical model is described, including assumptions. Next the details of the mesh that represents the experiment are described. A method for generating type curves in pressure versus flow rate space is presented and finally the data are mapped to permeability. We conclude with a discussion of the results.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1996

Effects of Periodic Unsteady Wake Flow and Pressure Gradient on Boundary Layer Transition Along the Concave Surface of a Curved Plate

Boundary layer transition and development on a turbomachinery blade is subjected to highly periodic unsteady turbulent flow, pressure gradient in longitudinal as well as lateral direction, and surface curvature. To study the effects of periodic unsteady wakes on the concave surface of a turbine blade, a curved plate was utilized. On the concave surface of this plate, detailed experimental investigations were carried out under zero and negative pressure gradient. The measurements were performed in an unsteady flow research facility using a rotating cascade of rods positioned upstream of the curved plate. Boundary layer measurements using a hot-wire probe were analyzed by the ensemble-averaging technique. The results presented in the temporal-spatial domain display the transition and further development of the boundary layer, specifically the ensemble-averaged velocity and turbulence intensity. As the results show, the turbulent patches generated by the wakes have different leading and trailing edge velocities and merge with the boundary layer resulting in a strong deformation and generation of a high turbulence intensity core. After the turbulent patch has totally penetrated into the boundary layer, pronounced becalmed regions were formed behind the turbulent patch and were extended far beyond the point they would occur in the corresponding undisturbed steady boundary layer.

Schobeiri, M. T.↗
NASA NTRS1987

An experimental investigation of straight and curved annular wall jets

Accurate turbulence measurements taken in wall jet flows are difficult to obtain, due to high intensity turbulence and problems in achieving two-dimensionality. The problem is compounded when streamwise curvature of the flow is introduced, since the jet entrainment and turbulence levels are greatly increased over the equivalent planar values. In this experiment, two-dimensional straight and curved incompressible wall jet flows are simulated by having a jet blow axially over a cylinder. Hot wire measurements and some Laser Doppler Velocimetry measurements are presented for straight and curved wall jet flows. The results for the straight wall showed good agreement between the annular flow data and the rectangular data taken by previous researchers. For the jets with streamwise curvature, there was agreement between the annular and corresponding rectangular jets for the flow region closest to the slot exit. An integral analysis was used as a simple technique to interpret the experimental results. Integral momentum calculations were performed for both straight and curved annular and two dimensional wall jets. The results of the calculation were used to identify transverse curvature parameters and to predict the values of those parameters which would delineate the region where the annular flow can satisfactorily simulate two dimensional flow.

Rodman, L. C.↗
NASA NTRS1989

Experimental investigation of straight and curved annular wall jets

Accurate turbulence measurements taken in wall jet flows are difficult to obtain, due to high intensity turbulence and problems in achieving two-dimensionality. The problem is compounded when streamwise curvature of the flow is introduced, since the jet entrainment and turbulence levels are greatly increased over the equivalent planar values. In this experiment, two-dimensional straight and curved incompressible wall jet flows are simulated by having a jet blow axially over a cylinder. Hot wire measurements and some Laser Doppler Velocimetry measurements are presented for straight and curved wall jet flows. The results for the straight wall showed good agreement between the annular flow data and the rectangular data taken by previous researchers. For the jets with streamwise curvature, there was agreement between the annular and corresponding rectangular jets for the flow region closest to the slot exit. An integral analysis was used as a simple technique to interpret the experimental results. Integral momentum calculations were performed for both straight and curved annular and two-dimensional wall jets. The results of the calculation were used to identify transverse curvature parameters and to predict the values of those parameters which would delineate the region where the annular flow can satisfactorily simulate two-dimensional flows.

Rodman, L. C.↗
NASA NTRS1982

Curved ducts with strong secondary motion - Velocity measurements of developing laminar and turbulent flow

Two orthogonal components of velocity and associated Reynolds stresses are determined in a square-sectioned, 90 degree bend of 2.3 radius ratio by utilizing laser-Doppler velocimetry for Reynolds numbers of 790 and 40,000. Results show that boundary layers at the bend inlet of 0.25 and 0.15 of the hydraulic diameter create secondary velocity maxima of 0.6 and 0.4 of the bulk flow velocity, respectively. It is concluded that the boundary layer thickness is important to the flow development, mainly in the first half of the bend, especially when it is reduced to 0.15 of the hydraulic diameter. Smaller secondary velocities are found for turbulent flow in an identical duct with a radius ratio of 7.0 than in the strongly curved bend, although their effect is more important to the streamwise flow development because of the smaller pressure gradients. In addition, the detail and accuracy of the measurements make them suitable for evaluation of numerical techniques and turbulence models.

Taylor, A. M. K. P.↗
NASA NTRS1972

A study of jet impingement on curved surfaces followed by oblique introduction into a freestream flow

An experimental investigation of the temperature and velocity fields generated by a two-dimensional transverse jet was conducted. An approximate analysis of a deflected radial plane jet was developed. An analytical model of aircraft ingestion was extended to include computation of the inlet flow field. An investigation of the use of flaps as thrust reversers was initiated. Analyses of the impingement of a round incompressible and a round compressible jet on a arbitrary axisymmetric surface were completed. A computer study of the effects on performance of thrust reverser geometry was completed and the results compared with existing data. An experimental investigation of three-dimensional jet impingement on nonplane surfaces was also initiated.

Tatom, J. W.↗
NASA NTRS1975

Experimental and analytical sonic nozzle discharge coefficients for Reynolds numbers up to 8 x 10 to the 6th power

Sonic discharge coefficients are obtained for two different geometry flow nozzles using high-pressure nitrogen gas (100 atm) with significant real-gas flow corrections. Throat Reynolds number range extended up to 8 million. Discharge coefficients for both nozzles monotonically increase in value at the high throat Reynolds numbers. The 95-percent confidence band for each nozzle is shown. Analytical discharge coefficients for the continuous and finite radius of curvature nozzle are presented. These analytical results for the laminar and turbulent boundary-layer cases are compared to experimental values for sonic flow. Experimental values are also compared to values calculated from the best empirical curve fit equation for subsonic flow.

Szaniszlo, A. J.↗
NASA NTRS1997

Flow Effects on the Flammability Diagrams of Solid Fuels

A research program is currently underway with the final objective of developing a fundamental understanding of the controlling mechanisms underlying the flammability diagrams of solid combustible materials and their derived fire properties. Given that there is a high possibility of an accidental fire occurring in a space-based facility, understanding the fire properties of materials that will be used in such facilities is of critical importance. With this purpose, the flammability diagrams of the materials, as those produced by the Lateral Ignition and Flame Spread Test (LIFT) apparatus and by a new forced flow device, the Forced Flow Ignition and Flame Spread Test (FIST) apparatus, will be obtained. The specific objective of the program is to apply the new flammability apparatus, which will more accurately reflect the potential ambient conditions of space-based environments, to the characterization of the materials for space applications. This paper presents a parametric study of oxidizer flow effects on the ignition curve of the flammability diagrams of PMMA. The dependence of the ignition delay time on the external radiant flux and either the sample width (LIFT) or the flow velocity (FIST) has been studied. Although preliminary, the results indicate that natural and forced convection flow changes, affect the characteristics of the ignition curves of the flammability diagrams. The major effect on the ignition time appears to be due to convective transfer variations at the fuel surface. At high radiant fluxes or high flow velocities, however, it appears that gas phase processes become increasingly important, affecting the overall ignition delay time. A numerical analysis of the solid fuel heating and pyrolysis has also been developed. The theoretical predictions approximate the experiments well for conditions in which the gas phase induction time is negligible.

Cordova, J. L.↗
DOE OSTI2026

FLOW BATTERY COST AND COMMERCIALIZATION TOOL (FlowBaCC) v.1.0

The Flow Battery Cost and Commercialization Tool (FlowBaCC) is a python-based framework used to project the costs and commercialization timelines for redox flow batteries. FlowBaCC combines learning curves for component costs and performance with adoption curves for market diffusion to project future system costs. The tool uses the bottom-up, spreadsheet-based Battery Performance and Cost Model for Flow Batteries (BatPaC-Flow) as the engine to translate learning curve inputs into full system costs. FlowBaCC provides capital costs and levelized costs of energy storage. The tool enables scenario analysis, sensitivity analysis, and uncertainty quantification (via grid and Monte Carlo methods).

Fu, Xiaoxu [Argonne National Laboratory (ANL), Arg↗
NASA NTRS1949

Longitudinal Stability and Control Characteristics of a Semispan Wind-Tunnel Model of the XF7U-1 Airplane and a Comparison with Complete-Model Wind-Tunnel Tests and Semispan-Model Wing-Flow Tests

An investigation was conducted on an 0.08-scale semispan model of the Chance Vought XF7U-1 airplane in the Langley high-speed 7- by 10-foot tunnel in the Mach number range from 0.40 to 0.97. The results are compared with those obtained with an 0.08-scale sting-mounted complete model tested in the same tunnel and with an 0.026-scale semispan model tested by the wing-flow method. The lift-curve slopes obtained for the 0.08-scale semispan model and the 0.026-scale wing-flow model were in good agreement but both were generally lower than the values obtained for the sting model. The results of an unpublished investigation have shown that tunnel-wall boundary-layer and strut-leakage effects can came the difference noted between the lift-curve slopes of the sting and the semispan data. Fair agreement was obtained among the data of the three models as regard the variation of pitching-moment coefficients with lift coefficient. The agreement between the complete and the semispan models was more favorable with the vertical fine on, because the wall-boundary-layer and strut leakage effects were less severe. In the Mach number range between 0.94 and 0.97, ailavator-control reversal was indicated in the wing-flow data near zero lift; Whereas, these same trends were indicated in the larger scale semispan data at somewhat higher lift coefficients.

Goodson, Kenneth W.↗
NASA NTRS1939

Design of centrifugal impeller blades

This paper restricts itself to radial impellers with cylindrical blades since, as Prasil has shown, the flow about an arbitrarily curved surface of revolution may be reduced to this normal form we have chosen by a relatively simple conformal transformation. This method starts from the simple hypotheses of the older centrifugal impeller theory by first assuming an impeller with an infinite number of blades. How the flow is then modified is then investigated. For the computation of flow for a finite number of blades, the approximation method as developed by Munk, Prandtl and Birnbaum, or Glauert is found suitable. The essential idea of this method is to replace the wing by a vortex sheet and compute the flow as the field of these vortices. The shape of the blades is then obtained from the condition that the flow must be along the surface of the blade.

Betz, A↗