Search NASA⌕ Search

SEARCH · Search NASA

Results for “FLOW - COMPRESSORS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Demonstration of Microwave Cavity Transducer Performance in High Temperature Fluid Flow Sensing: Development of Microwave Cavity Flow Meter for Advanced Reactor High Temperature Fluids

We are investigating a microwave resonant cavity transducer for flow sensing in the vessel of a high temperature fluid advanced reactor (AR), such as a molten salt cooled reactor (MSCR) or a sodium fast reactor (SFR). This transducer is a hollow metallic cylindrical cavity, with one of the flat walls of the cylinder flexible enough to undergo microscopic deflection due to dynamic fluid pressure. Membrane deflection leads to a shift in the microwave resonant frequency, which can be detected with a spectrum analyzer. We have performed a preliminary proof-of-principle test of flow sensing in high temperature liquid sodium in environment, which is similar to that of an advanced reactor. The liquid sodium setup consists of a cylindrical vessel with a center feed line, where a transducer inserted through the top cap of the vessel measures velocity of the impinging liquid jet. For this test, we have developed a cylindrical resonator, which was machined from stainless steel 316 and electroplated with silver on the interior surfaces. Outer diameter of the cylindrical cavity is approximately 3cm, and the thin wall is approximately 200µm thick. We have also developed and insertion probe consisting of a 50cm WR-42 brass waveguide enclosed in a protective SS316 tube. The cavity was excited through a WR-42 waveguide through a subwavelength hole on the side of the wall of the cylinder in the TE 011 mode with resonant frequency f ≈ 17.8GHz. As a calibration experiment, we have assembled a water vessel with a center feed, and with dimensions similar to those of the liquid sodium setup. Frequency shift of the cavity spectral response was obtained at room temperature and ambient pressure by gradually increasing water flow rate from 0 to 25GPM (gallons per minute). Corresponding monotonic increase of resonant frequency by several hundred KHz was observed. Next, a sodium flow rate sensing study was performed in a liquid sodium vessel at 340° C temperature and ambient pressure. The flow rate was changed by varying sodium pump power, and a frequency shift of several hundred KHz was observed.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2026

Towards a Unified Low-Cost Flow Plate, Flow-Field, PTL Solution for Proton Exchange Membrane Electrolyzers

Proton exchange membrane (PEM) water electrolysis is a highly efficient method for hydrogen production. Research cells typically consist of one proton exchange membrane, two catalyst layers, two porous transport layers, two flow-field plates, and two endplates. In commercial systems, the machined flow-field plates that are employed in research cells are typically replaced by stamped parts or open mesh material solutions to reduce manufacturing cost at scale. Nonetheless, the cell contains about 8 total interfaces: bipolar plate / flow plate material / porous transport medium / electrode / membrane / electrode / porous transport medium / flow plate material / bipolar plate. All these materials and interfaces need to be optimized for maximum performance and efficiency. Reducing the amount of interfaces by combining individual cell components directly benefits the fabrication cost (by reducing the parts count and the needs for surface coatings) and the electrochemical performance (by reducing ohmic losses). We have designed a novel PEM electrolysis cell with a piece of channeled titanium felt functioning as both the anode flow-field and the PTL, referred to as the channeled diffusion layer (CDL). The pores of the felt facilitate both in-plane and through-plane diffusion, ensuring maximum catalyst utilization while also minimizing mass transport loss. The titanium felt can be mass manufactured with existing stamping and forming methods and is therefore a promising candidate to reduce the capital cost of PEM electrolyzers whilst improving hydrogen production efficiency. Experiments conducted with 3mg IrOx/cm2 loading MEAs have shown a approximately 40% boost in peak current by implementing the CDL design. Low catalyst-loading MEAs are being tested in ongoing experiments and their results will be discussed and compared.

08 HYDROGEN↗
DOE OSTI2025

Kinematic flow from the flow of cuts

The wavefunction coefficients of conformally coupled scalars in power-law FRW cosmologies satisfy differential equations governed by a set of simple combinatorial rules known as the kinematic flow. In this paper we derive the kinematic flow, expressed using a set of differential forms referred to as the cut basis, from a geometric perspective, relying solely on the cosmological hyperplane arrangement and without invoking bulk physics. Each element of the cut basis corresponds to the positive geometry associated to an independent cut of the physical FRW-form and can be labeled by decorating (minors of) the truncated Feynman graph with an acyclic orientation. We provide a straightforward prescription to associate a logarithmic differential form to each element of the cut basis by considering its corresponding decorated graph. Moreover, we show that the residues of the physical FRW-form are canonical forms of certain graphical zonotopes labeled by the same set of decorated graphs. These zonotopes control the cut combinatorics -- flow of cuts -- of the physical FRW-form and the cut basis (by construction). Using the theory of relative twisted cohomology and intersection theory, we derive a closed form formula for the differential equations of the cut basis. We also introduce combinatorial rules that compute the kinematic differential of any basis element without explicit calculation. The combinatorics of our differential equations is a natural consequence of the flow of cuts and is equivalent (up to rescaling) to the kinematic flow for the recently studied time integral basis. In particular, our differential equations decouple into exponentially many sectors, one for each way of cutting a subset of edges of the graph.

General Relativity and Quantum Cosmology↗
NASA NTRS1969

An Analog Computer Study of the Low-Frequency Flow Dynamics of Two Nuclear-Rocket Cold-Flow Engine Systems

An analog computer study is made of the low-frequency flow dynamics observed with liquid hydrogen flowing in two different nuclear-rocket cold-flow (unfueled) engine systems. The prediction of the low-frequency response depends largely upon the generation of the proper mass-flow storage in the system. This is achieved by relating, in the model lumping, the average values of fluid enthalpy and a certain thermodynamic fluid property. A two-phase state equation is derived for thermodynamic equilibrium between the gas and liquid phases. Parametric studies are made which demonstrate the effect of the pump characteristics on the flow damping.

Fox, Harry W., Jr.↗
NASA NTRS1974

Analytical and experimental study of mean flow and turbulence characteristics inside the passages of an axial flow inducer

The effort conducted to gather additional understanding of the complex inviscid and viscid effects existing within the passages of a three-bladed axial flow inducer operating at a flow coefficient of 0.065 is summarized. The experimental investigations included determination of the blade static pressure and blade limiting streamline angle distributions, and measurement of the three components of mean velocity, turbulence intensities and turbulence stresses at locations inside the inducer blade passage utilizing a rotating three-sensor hotwire probe. Applicable equations were derived for the hotwire data reduction analysis and solved numerically to obtain the appropriate flow parameters. Analytical investigations were conducted to predict the three-dimensional inviscid flow in the inducer by numerically solving the exact equations of motion, and to approximately predict the three-dimensional viscid flow by incorporating the dominant viscous terms into the exact equations. The analytical results are compared with the experimental measurements and design values where appropriate.

Gorton, C. A.↗
NASA NTRS1977

A Green's function formulation for a nonlinear potential flow solution applicable to transonic flow

Routine determination of inviscid subsonic flow fields about wing-body-tail configurations employing a Green's function approach for numerical solution of the perturbation velocity potential equation is successfully extended into the high subsonic subcritical flow regime and into the shock-free supersonic flow regime. A modified Green's function formulation, valid throughout a range of Mach numbers including transonic, that takes an explicit accounting of the intrinsic nonlinearity in the parent governing partial differential equations is developed. Some considerations pertinent to flow field predictions in the transonic flow regime are discussed.

Baker, A. J.↗
NASA NTRS1978

Concerning isothermal self-similar blast waves. I - One-dimensional flow and its stability. II - Two-dimensional flow and its stability

One-dimensional self-similar isothermal flow behind a blast wave propagating in a medium whose density varies with distance is investigated for the cases of one-dimensional and two-dimensional flow. The isothermal flow model is adopted as an alternative to adiabatic models of self-similar flow, which neglect heat flux. The topology of the one-dimensional flow solutions, the singularities, and the influence of boundary conditions are discussed; the instability of the isothermal blast waves against nonself-similar perturbations is also considered. The number of critical points in the two-dimensional solutions is found to vary from the number in the one-dimensional problem.

Lerche, I.↗
NASA NTRS1964

Flow diverter value and flow diversion method

A flow diverter valve applicable to any fluid flow system requiring rapid bleed or bypass is disclosed. Examples of application of the flow diverter valve to a liquid rocket and a turbojet aircraft engine are given. Features of the valve include: (1) an independent fluid source is used to activate the flow diverter valve toward its closed position during its initial stage of travel; (2) the flow diverter port area and size is unlimited and the valve travel is unlimited; and (3) the valve housing is fabricated such that the valve can be a one step valve, a two step valve, or include as many steps as are found desirable.

Arline, S. B.↗
NASA NTRS1981

A potential-flow/boundary-layer method for calculating subsonic and transonic airfoil flow with trailing-edge separation

The development of a potential-flow/boundary-layer method for calculating subsonic and transonic turbulent flow past airfoils with trailing-edge separation is reported. A moment-of-momentum integral boundary-layer method is used which employs the law-of-the-wall/law-of-the-wake velocity profile and a two-layer eddy-viscosity model and ignores the laminar sublayer. All integrals across the boundary layer are obtained in closed form. Separation is assumed to occur when the shearing-stress velocity vanishes. A closed-form solution is derived for separated-flow regions where the shearing stress is negligible. In the potential-flow method, the exact form of the airfoil boundary condition is used, but it is applied at the chord line rather than the airfoil surface. This allows the accurate computation of flow about airfoils at large angles of attack but permits the use of body-oriented Cartesian computational grids. The governing equation for the perturbation velocity potential contains several terms in addition to the classical small-disturbance terms.

Barnwell, R. W.↗
NASA NTRS1982

Experimental study of time-dependent flows in laboratory atmospheric flow models

Baroclinic waves in a rotating, differentially-heated annulus of liquid were studied in support of the Atmospheric General Circulation Experiment. Specific objectives were to determine: (1) the nature of the flow at shallow depths, (2) the effect of a rigid lid vs. free surface, and (3) the nature of fluctuations in the waves as a function of rotation rate, depth, and type of surface. It is found that flows with a rigid lid are basically the same as those with a free surface, except for a decrease in flow rate. At shallow depths steady flows are found in essentially the same form, but the incidence of unsteady flows is greatly diminished.

Rush, J. E.↗
NASA NTRS1982

Flow analysis of nozzle installations with strong airplane flow interactions

A numerical procedure has been developed to calculate the flow fields resulting from the viscous-inviscid interactions that occur when a strong jet exhaust and aircraft flow field coupling exists. The approach used in the current procedure is to divide the interaction region into zones which are either predominantly viscous or inviscid. The flow in the inviscid zone, which surrounds most of the aircraft, is calculated using an existing linearized potential flow code. The viscous flow zone, which encompasses the jet plume, is modeled using a parabolized Navier-Stokes code. The key feature of the present procedure is the coupling of the zonal solutions such that sufficient information is transferred between the zones to preserve the effects of the interactions. The zonal boundaries overlap with the boundary conditions being the information link between zones. An iteraction scheme iterates the coupled analysis until convergence has been obtained. The procedure has been successfully used for several test cases for which the computed results are presented.

Roberts, D. W.↗
NASA NTRS1984

Inlet flow field investigation. Part 1: Transonic flow field survey

A wind tunnel investigation was conducted to determine the local inlet flow field characteristics of an advanced tactical supersonic cruise airplane. A data base for the development and validation of analytical codes directed at the analysis of inlet flow fields for advanced supersonic airplanes was established. Testing was conducted at the NASA-Langley 16-foot Transonic Tunnel at freestream Mach numbers of 0.6 to 1.20 and angles of attack from 0.0 to 10.0 degrees. Inlet flow field surveys were made at locations representative of wing (upper and lower surface) and forebody mounted inlet concepts. Results are presented in the form of local inlet flow field angle of attack, sideflow angle, and Mach number contours. Wing surface pressure distributions supplement the flow field data.

Yetter, J. A.↗
NASA NTRS1986

Flow visualization of secondary flows in three curve ducts

Streak photography flow measurements are made for secondary flows in three 90-deg curved ducts of square cross section and different radii of curvature, at Dean numbers of 15,000-36,000 and radius ratios of 0.5, 2.3, and 3.0. Attention is given to secondary flow patterns for three cross sections in each bend: the inlet zero-deg plane, the midpoint 45-deg plane, and the outlet 90-deg plane. After a rapid transition region, the pressure-driven secondary flow patterns were characterized by flow moving toward the outer curved wall at the axial midplane and returning to the inner wall along the duct walls. The 0.5-radius ratio elbow was found to have the greatest influence on upstream inlet conditions.

Sanz, G. M.↗
NASA NTRS1987

Flow visualization model of the leeside flows over conically cambered delta wings at supersonic speeds

Surface pressure, flow visualization, and force-and-moment data have been obtained for four, variously conically-cambered delta wing models in a range of flow conditions, with a view to leeside flow mechanisms. The influences exerted by Mach number, angle-of-attack, and camber are determined. An analysis of photographic data leads to the analysis of 12 distinctive leeside flow types, which are further categorizable into two groups respectively possessing either one or two dominant features in the leeside flow field: in the former, either the leading edge or hinge line are the originators of the dominant feature; in the latter, both the leading edge and hinge line are generators.

Wood, Richard M.↗
NASA NTRS1987

Review of flow visualization techniques for unsteady flows

The purpose of this article is to review some of the novel flow visualization techniques that are particularly suited for studying unsteady flows. While many of these techniques were originally developed for steady flow fields, the present paper will emphasize applications to time-dependent flows. The flow visualization methods presented include those that make use of scattered light from small particles or foreign additives as well as those that make use of changes in the index of refraction.

Gad-El-hak, Mohamed↗
NASA NTRS1990

A package for 3-D unstructured grid generation, finite-element flow solution and flow field visualization

A set of computer programs for 3-D unstructured grid generation, fluid flow calculations, and flow field visualization was developed. The grid generation program, called VGRID3D, generates grids over complex configurations using the advancing front method. In this method, the point and element generation is accomplished simultaneously, VPLOT3D is an interactive, menudriven pre- and post-processor graphics program for interpolation and display of unstructured grid data. The flow solver, VFLOW3D, is an Euler equation solver based on an explicit, two-step, Taylor-Galerkin algorithm which uses the Flux Corrected Transport (FCT) concept for a wriggle-free solution. Using these programs, increasingly complex 3-D configurations of interest to aerospace community were gridded including a complete Space Transportation System comprised of the space-shuttle orbitor, the solid-rocket boosters, and the external tank. Flow solutions were obtained on various configurations in subsonic, transonic, and supersonic flow regimes.

Parikh, Paresh↗
NASA NTRS1991

A water tunnel flow visualization study of the vortex flow structures on the F/A-18 aircraft

The vortex flow structures occurring on the F/A-18 aircraft at high angles of attack were studied. A water tunnel was used to gather flow visualization data on the forebody vortex and the wing leading edge extension vortex. The longitudinal location of breakdown of the leading edge vortex was found to be consistently dependent on the angle of attack. Other parameters such as Reynolds number, model scale, and model fidelity had little influence on the overall behavior of the flow structures studied. The lateral location of the forebody vortex system was greatly influenced by changes in the angle of sideslip. Strong interactions can occur between the leading edge extension vortex and the forebody vortex. Close attention was paid to vortex induced flows on various airframe components of the F/A-18. Reynolds number and angle of attack greatly affected the swirling intensity, and therefore the strength of the studied vortices. Water tunnel results on the F/A-18 correlated well with those obtained in similar studies at both full and sub scale levels. The water tunnel can provide, under certain conditions, good simulations of realistic flows in full scale configurations.

Sandlin, Doral R.↗