Search NASA⌕ Search

SEARCH · Search NASA

Results for “Feature engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Computational analysis of ramjet engine inlet interaction

A computational analysis of a ramjet engine at Mach 3.5 has been conducted and compared to results obtained experimentally. This study focuses on the behavior of the inlet both with and without combustor backpressure. Increased backpressure results in separation of the body side boundary layer and a resultant static pressure rise in the inlet throat region. The computational results compare well with the experimental data for static pressure distribution through the engine, inlet throat flow profiles, and mass capture. The computational analysis slightly underpredicts the thickness of the engine body surface boundary layer and the extent of the interaction caused by backpressure; however, the interaction is observed at approximately the same level of backpressure both experimentally and computationally. This study demonstrates the ability of two different Navier-Stokes codes, namely RPLUS and PARC, to calculate the flow features of this ramjet engine and to provide more detailed information on the process of inlet interaction and unstart.

Duncan, Beverly↗
NASA NTRS2005

An Updated Assessment of NASA Ultra-Efficient Engine Technologies

NASA's Ultra Efficient Engine Technology (UEET) project features advanced aeropropulsion technologies that include highly loaded turbomachinery, an advanced low-NOx combustor, high-temperature materials, and advanced fan containment technology. A probabilistic system assessment is performed to evaluate the impact of these technologies on aircraft CO2 (or equivalent fuel burn) and NOx reductions. A 300-passenger aircraft, with two 396-kN thrust (85,000-lb) engines is chosen for the study. The results show that a large subsonic aircraft equipped with the current UEET technology portfolio has very high probabilities of meeting the UEET minimum success criteria for CO2 reduction (-12% from the baseline) and LTO (landing and takeoff) NOx reductions (-65% relative to the 1996 International Civil Aviation Organization rule).

Tong Michael T.↗
NASA NTRS2023

Nasa Hytec CMC Turbine Blade Durability

The objective of the CMC turbine blade durability program is to identify critical material and design parameters that affect durability of ceramic matrix composite (CMC) turbine blades. A baseline architecture for a cooled high-pressure turbine (HPT) CMC blade and accompanying sub-component test articles were developed with the intent to demonstrate through analysis and subcomponent testing how material and design parameters impact key failure modes. As part of this program, a notional architecture for a cooled CMC blade was matured through a design review rhythm to produce a blade test article containing the necessary features required for operation in an engine like environment. Further validation of the durability of these features were achieved through coupon and sub-component testing to demonstrate the durability of cooling hole configurations and blade attachment designs. Analytical methods were also used to evaluate the acceptability of the baseline blade test article architecture against relevant design requirements and identify abatement and recommended changes to key design drivers to improve component durability for future design iterations.

CMC, Blade↗
NASA NTRS2004

A Probabilistic Assessment of NASA Ultra-Efficient Engine Technologies for a Large Subsonic Transport

NASA's Ultra Efficient Engine Technology (UEET) program features advanced aeropropulsion technologies that include highly loaded turbomachinery, an advanced low-NOx combustor, high-temperature materials, intelligent propulsion controls, aspirated seal technology, and an advanced computational fluid dynamics (CFD) design tool to help reduce airplane drag. A probabilistic system assessment is performed to evaluate the impact of these technologies on aircraft fuel burn and NOx reductions. A 300-passenger aircraft, with two 396-kN thrust (85,000-pound) engines is chosen for the study. The results show that a large subsonic aircraft equipped with the UEET technologies has a very high probability of meeting the UEET Program goals for fuel-burn (or equivalent CO2) reduction (15% from the baseline) and LTO (landing and takeoff) NOx reductions (70% relative to the 1996 International Civil Aviation Organization rule). These results are used to provide guidance for developing a robust UEET technology portfolio, and to prioritize the most promising technologies required to achieve UEET program goals for the fuel-burn and NOx reductions.

Tong, Michael T.↗
NASA NTRS1998

Hydrodynamic Design of the Fastrac Turbopump

A 60,000 lb trust liquid Oxygen (LOX) and rocket propellant #1 (RP-1) rocket engine is being developed at the Marshall Space Flight Center (MSFC) as part of NASA's ongoing effort to lower the cost of access to space. The goal of the program is to demonstrate a low cost rocket engine with acceptable performance. In order to reduce design and development risk, computational fluid dynamics (CFD) analysis was used extensively in the design process, especially in the design of the turbopump. This paper documents the process used and significant results obtained during the design of the LOX and RP-1 pumps. This includes the design of the inlet manifolds, the integral inducer-impellers, the diffusers, and the collector volutes. The resulting designs incorporate low-cost design features while meeting the engine cycle requirements.

Garcia, Roberto↗
NASA NTRS2019

Progress in Additively Manufactured Copper-Alloy GRCop-84, GRCop-42, and Bimetallic Combustion Chambers for Liquid Rocket Engines

Additive Manufacturing (AM) has significantly evolved over the last decade for use in the aerospace industry, particularly for liquid rocket engines. AM offers a considerable departure from traditional manufacturing to rapidly fabricate components with complex internal features. High performance liquid rocket engine combustion chambers that operate in a high heat flux environment are fabricated using a copper-alloy liner with a series of integral coolant channels. Copper-alloys provide the necessary conductivity and material strength for adequate design margins offering high performance without the need for film coolant. Copper-alloys present unique challenges to properly melt the powder in laser-based AM processes due to their high reflectivity and conductivity. Starting in 2014, NASA’s Marshall Space Flight Center (MSFC) and Glenn Research Center (GRC) have developed a process for AM of GRCop (Copper- Chrome-Niobium) alloys using Selective Laser Melting (SLM). GRCop, originally developed at GRC, is a high conductivity, high-strength, dispersion strengthened copper-alloy for use in high-temperature, high heat flux applications. NASA has completed significant material characterization and testing, along with hot-fire testing, to demonstrate that GRCop-42 and GRCop-84 alloys are suitable for use in combustion chambers. Additional development and testing has been completed on AM bimetallic chambers using GRCop-84 liners and superalloy jackets, fabricated using two Directed Energy Deposition (DED) processes: Electron Beam Freeform Fabrication (EBF³) and Blown Powder DED. NASA completed hot-fire testing on various AM chambers using GRCop-84, GRCop-42, and bimetallic chambers in Liquid Oxygen (LOX)/Hydrogen, LOX/Methane, and LOX/Kerosene propellants.

Gradl, Paul R.↗
NASA NTRS1979

A method to estimate weight and dimensions of large and small gas turbine engines

A computerized method was developed to estimate weight and envelope dimensions of large and small gas turbine engines within + or - 5% to 10%. The method is based on correlations of component weight and design features of 29 data base engines. Rotating components were estimated by a preliminary design procedure which is sensitive to blade geometry, operating conditions, material properties, shaft speed, hub tip ratio, etc. The development and justification of the method selected, and the various methods of analysis are discussed.

Onat, E.↗
NASA NTRS1927

Description of the NACA Universal Test Engine and Some Test Results

This report describes the 5-inch bore by 7-inch stroke single cylinder test engine used at the Langley Field Laboratory of the National Advisory Committee for Aeronautics in laboratory research on internal-combustion engine problems and presents some results of tests made therewith. The engine is arranged for variation over wide ranges, of the compression ratio and lift and timing of both inlet and exhaust valves while the engine is in operation. Provision is also made for the connection of a number of auxiliaries. These features tend to make the engine universal in character, and especially suited for the study of certain problems involving change in compression ratio, valve timing, and lift.

Ware, Marsden↗
NASA NTRS1958

Low-Speed Aerodynamic and Hydrodynamic Characteristics of a Proposed Supersonic Multijet Water-Based Hydro-Ski Aircraft with Upward-Rotating Engines

The low-speed aerodynamic and hydrodynamic characteristics of a proposed multijet water-based aircraft configuration for supersonic operation have been investigated. The design features include upward-rotating engines, body indentation, a single hydro-ski, and a wing with an aspect ratio of 3.0, a taper ratio of 0.143, 36.90 sweepback of the quarter-chord line, and NACA 65AO04 airfoil sections. For the aerodynamic investigation, with the flaps retracted, the model was longitudinally and directionally stable up to the stall. The all-movable horizontal tail was capable of trimming the model up to a lift coefficient of approximately 0.87. All flap configurations investigated had a tendency to become longitudinally unstable at stall. The effectiveness of the all-movable horizontal tail increased with increasing lift coefficient for all flap configurations investigated; however, with the large static margin of the configuration with the center of gravity at 0.25 mean aerodynamic chord, the all-movable horizontal tail was not powerful enough to trim all the various flapped configurations investigated throughout the angle-of-attack range. For the hydrodynamic investigation, longitudinal stability during take-offs and landings was satisfactory. Decreasing the area of the hydro-ski 60 percent increased the maximum resistance and emergence speed 40 and 70 percent, respectively. Without the jet exhaust, the resistance was reduced by simulating the vertical-lift component of the forward engines rotated upward. However, the jet exhaust of the forward engines increased the maximum resistance approximately 60 percent. The engine inlets and horizontal tail were free from spray for all loads investigated and for both hydro-ski sizes.

Petynia, William W.↗
NASA NTRS1982

Conceptual design and cost analysis of hydraulic output unit for 15 kW free-piston Stirling engine

A long-life hydraulic converter with unique features was conceptually designed to interface with a specified 15 kW(e) free-piston Stirling engine in a solar thermal dish application. Hydraulic fluid at 34.5 MPa (5000 psi) is produced to drive a conventional hydraulic motor and rotary alternator. Efficiency of the low-maintenance converter design was calculated at 93.5% for a counterbalanced version and 97.0% without the counterbalance feature. If the converter were coupled to a Stirling engine with design parameters more typcial of high-technology Stirling engines, counterbalanced converter efficiency could be increased to 99.6%. Dynamic computer simulation studies were conducted to evaluate performance and system sensitivities. Production costs of the complete Stirling hydraulic/electric power system were evaluated at $6506 which compared with $8746 for an alternative Stirling engine/linear alternator system.

White, M. A.↗
NASA NTRS1989

Design and analysis report for the flight weight 20-inch Columbium secondary nozzle for the RL10 engine

Pratt & Whitney (P and W) is currently under contract to NASA-LeRC for a multi-year program to evaluate the feasibility of the RL10-IIB/IIC engine models and the various improvements which broaden the engine capabilities and range of applications. The features being evaluated include the operation of the RL10 engine at low thrust levels and/or high mixture ratio levels and the addition of a high area ratio (250:1) translating nozzle to the engine to increase its specific impulse while shortening the installed engine length. The translating nozzle for the RL10-IIB/IIC engine is approximately 55 inches long with an exit plane diameter of 71 inches and an inlet plane diameter of 40 inches. This report documents the design and analysis work done investigating a small subscale Columbium nozzle which could be built and tested to provide findings which then could be incorporated into the high area ratio nozzle final design for the RL10-IIB/IIC engine. This report documents the design and analysis work done investigating a small subscale Columbium nozzle which could be built and tested to provide findings which then could be incorporated into the high area ratio nozzle final design for the RL10-IIB/IIC engine. The length of the subscale nozzle is 20 in.; its exit diameter is 46 in. With the nozzle in the stowed position, an RL10A-3-3A engine system is 70 inches long (Area Ratio = 61:1); with the nozzle deployed the engine length and area ratio are increased to 90 inches and 83:1 respectively. The increase in area ratio provides a calculated increase of 7 + or - 1 second of specific impulse.

Castro, J. H.↗
NASA NTRS1998

Using Approximations to Accelerate Engineering Design Optimization

Optimization problems that arise in engineering design are often characterized by several features that hinder the use of standard nonlinear optimization techniques. Foremost among these features is that the functions used to define the engineering optimization problem often are computationally intensive. Within a standard nonlinear optimization algorithm, the computational expense of evaluating the functions that define the problem would necessarily be incurred for each iteration of the optimization algorithm. Faced with such prohibitive computational costs, an attractive alternative is to make use of surrogates within an optimization context since surrogates can be chosen or constructed so that they are typically much less expensive to compute. For the purposes of this paper, we will focus on the use of algebraic approximations as surrogates for the objective. In this paper we introduce the use of so-called merit functions that explicitly recognize the desirability of improving the current approximation to the objective during the course of the optimization. We define and experiment with the use of merit functions chosen to simultaneously improve both the solution to the optimization problem (the objective) and the quality of the approximation. Our goal is to further improve the effectiveness of our general approach without sacrificing any of its rigor.

Torczon, Virginia↗
NASA NTRS1972

Maintainability of the Space Shuttle Orbiter main engine.

Review of the long-life and minimum-turnaround-maintenance features in the design of the Space Shuttle Orbiter main engine aimed at reducing the latter's field operating costs. These features include the regeneratively cooled hot-gas system selected, the provision of additional fatigue margins in the design of rotating machinery elements, and employment of a proven approach to engine condition monitoring for fault detection and identification.

Goe, R. T.↗
NASA NTRS1972

Development of a digital control system for a spacecraft propulsion test facility

A digital computer control and abort system which is used at NASA-Lewis research center is described. The system was designed to control test operations such as rocket engine testing, structure testing, and wind tunnel tests. Because of the nature of spacecraft system testing, particularly rocket engine testing, the unique features of the system are, control function updating at a 20 millisecond rate, continuous abort monitoring and a software system designed for short duration tests rather than continuous on-line control. To accomplish these system requirements, special hardware was designed. The presentation includes a description of the computer system and special interface hardware as well as a general description of the software used.

Smalley, R. R.↗
NASA NTRS1972

Development of a digital control system for a spacecraft propulsion test facility.

A digital computer control and abort system which is used at NASA-Lewis Research Center's Plum Brook Test Facilities is described. The system was designed by NASA personnel to control test operations such as rocket engine testing, structure testing, and wind tunnel tests. Because of the nature of spacecraft system testing, particularly rocket engine testing, the unique features of the system are, control function updating at a 20 millisecond rate, continuous abort monitoring and a software system designed for short duration tests rather than continuous on-line control. To accomplish these system requirements, special hardware was designed. The presentation will include a description of the computer system including special interface hardware as well as a general description of the software used.

Smalley, R. R.↗
NASA NTRS1972

Development of a digital control system for a spacecraft propulsion test facility.

Description of a digital computer control and abort system designed by NASA personnel to control test operations such as rocket engine testing, structure testing, and wind tunnel tests. Because of the nature of spacecraft system testing, particularly rocket engine testing, the unique features of the system are, control function updating at a 20 millisecond rate, continuous abort monitoring, and a software system designed for short duration tests rather than continuous on-line control. The presentation includes a description of the computer system and special interface hardware as well as a general description of the software used.

Smalley, R. R.↗
NASA NTRS1973

Performance of an annual combustor designed for a low-cost turbojet engine

Performance tests were conducted on a combustor designed for use in a low-cost turbojet engine. Low-cost features included the use of very inexpensive simplex fuel nozzles and combustor liners of perforated sheet material. Combustion efficiencies at the altitude-cruise and sea-level design points were approximately 94 and 96 percent, respectively. The combustor isothermal total-pressure loss was 8.8 percent at the altitude-cruise-condition diffuser-inlet Mach number of 0.335. The combustor-exit temperature pattern factor was less than 0.3 at the altitude-cruise, sea-level-cruise, and sea-level-static design conditions. The combustor-exit average radial temperature profiles at all conditions were in very good agreement with the design profile. The intense mixing required because of the very high combustor heat-release rate had an adverse effect on ignition capability at altitude windmilling design conditions.

Fear, J. S.↗