Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fuel efficiency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

A low temperature unitized regenerative fuel cell realizing 60% round trip efficiency and 10 000 cycles of durability for energy storage applications

Unitized regenerative fuel cells (URFC) convert electrical energy to and from chemical bonds in hydrogen. URFCs have the potential to provide economical means for efficient long-term, seasonal, energy storage and on-demand conversion back to electrical energy. We first optimize the catalyst layer for discrete electrolyzer and fuel cell and then configure the URFC. The goal is to identify a cost competitive configuration for URFCs, and demonstrate it in terms of upper limit of round trip efficiencies (RTEs). Two possible configurations of URFCs are compared via experiments and techno-economic analysis (TEA), which emphasize the advantages of the unconventional constant-electrode (CE) URFC over the traditional constant-gas (CG) configuration. We also study the stability via accelerated stress tests (ASTs) and demonstrate steady state operation in a daily cycle for day to night energy shifting. From the investigations, the optimum composition of the URFC anode catalyst layer is 90 at% Ir-black balanced by Pt-black for both CE and CG configurations. At 80 °C and 1 A cm -2 , the optimized CE URFC achieves 57% and 60% RTE with air and O 2 as the reductant gases, respectively. We then evaluated the differences in durability using an AST over 10k charge–discharge cycles; the results reveal that the wider potential window at the anode in CE (0.05–1.55 V) has minimal effect on catalyst layer stability compared to CG (0.55–1.55 V). Furthermore, there was no degradation up to the range of 2k–5k cycles; beyond that the fuel cell (discharge) performance degraded while the electrolyzer (charge) performance was still stable. Finally, the observations here indicate substantial potential to employ URFCs as efficient and cost-effective bidirectional energy-conversion devices within energy storage and utilization systems after appropriate technological and operational optimizations.

25 ENERGY STORAGE↗
DOE OSTI2025

Development of Hydrogen Burner for FT4000® Aeroderivative Engine - Final Report

This report details an effort to develop a retrofittable fuel/air injector for the FT4000® aeroderivative gas turbine that enables use of hydrogen as a carbon-free fuel for efficient power generation. The FT4000 engine’s low-NOx combustor was developed by Pratt & Whitney and RTX Technology Research Center with core technology from the Pratt & Whitney PW4000 turbofan aircraft engine. The current FT4000 production engine operates on either natural gas or No. 2 fuel oil with water injection to achieve high thermal efficiency and low emissions. This engine is fielded by Mitsubishi Power Aero and delivers 70 MW of power with a simple-cycle efficiency of over 41% when operating with wet compression. The work reported here advances the technology readiness level of the FT4000 combustor for operation with hydrogen, starting with an experimental assessment of the current production hardware with increasing hydrogen content mixed with natural gas and ending with improved nozzle concepts for fully robust operation with 100% hydrogen. High-pressure single-sector combustor rig tests have been completed, demonstrating the ability for the dual fuel nozzle to operate an FT4000 combustor on 100% hydrogen with low nitrogen oxide (NOx) emissions. Metal temperature measurements and video images of the flame structure from zero to 100% hydrogen highlight opportunities to improve the fuel nozzle robustness for high hydrogen conditions. The design of new fuel/air mixer concepts to improve durability and operability with high hydrogen levels was also completed. A total of eleven new concepts were developed and analyzed, ranging from modifications to the bill-of-materials nozzle to fully clean sheet designs. The concepts were evaluated with non-reacting and reacting flow evaluations to assess the performance of the new hardware designs. Non-reacting tests included Phase Doppler Particle Analysis (PDPA) for droplet size and velocity, mechanical patternation for liquid water flux, and planar laser induced fluorescence (PLIF) with acetone-seeding for gaseous fuel/air mixing characterization. Five scaled candidate fuel nozzle designs, in addition to a scaled bill-of-materials nozzle, were then successfully evaluated in an atmospheric pressure burner rig. The nozzles were evaluated for performance with natural gas, hydrogen/natural gas blends, and pure hydrogen. For 100% hydrogen, the nozzles were evaluated with and without water injection. Optical and infrared imaging of the flame and fuel nozzle was captured. NOx emissions were sampled from fixed emissions probes. The results show measurable differences between the various designs, and the data was used to down-select the two most promising designs to advance to future full pressure rig testing. Results from this study have cleared the current production FT4000 engines with dual fuel nozzles to operate at baseload power on blends of hydrogen mixed with natural gas and water. Two promising nozzle designs have been developed to enable fully robust operation with up to 100% hydrogen. These nozzles require validation at full baseload operating conditions before they can be introduced to the field.

03 NATURAL GAS↗
DOE OSTI2024

OPERATION OF FT4000® SINGLE NOZZLE COMBUSTOR WITH HIGH HYDROGEN

This paper reports initial results from an effort to develop a retrofittable fuel/air injector for the FT4000® aeroderivative gas turbine that enables use of hydrogen as a carbon-free fuel for efficient power generation. The FT4000 engine’s low-NOx combustor was developed by Pratt & Whitney and RTX Technology Research Center with core technology from the Pratt & Whitney PW4000 turbofan aircraft engine. The work reported here advances the technology readiness level of the FT4000 combustor for operation with hydrogen, starting with an experimental assessment of the current production hardware with increasing hydrogen content mixed with natural gas. High-pressure single-sector combustor rig tests have been completed, demonstrating the ability for the dual fuel nozzle to operate an FT4000 combustor on 100% hydrogen with low nitrogen oxide (NOx) missions. Metal temperature measurements and video images of the flame structure from zero to 100% hydrogen highlight opportunities to improve the fuel nozzle robustness for high hydrogen conditions. The current FT4000 production engine operates on either natural gas or No. 2 fuel oil with water injection to achieve high thermal efficiency and low emissions. This engine is fielded by Mitsubishi Power Aero and delivers 70 MW of power with a simple-cycle efficiency of over 41% when operating with wet compression. Results from this study have cleared the current production FT4000 engines with dual fuel nozzles to operate at baseload power on blends of hydrogen mixed with natural gas and water.

power generation↗
DOE OSTI2020

Oxidation kinetic modelling of Fe-based oxygen carriers for chemical looping applications: Impact of the topochemical effect

Chemical looping is a promising technology for fossil fuel utilization due to its high fuel conversion efficiency with in-situ CO 2 capture capability. Metal oxide are used as oxygen carriers (OCs) and circulate between a fuel reactor and an air reactor to perform reduction and oxidation reactions, respectively. In general, OC exiting the fuel reactor is not reduced fully to its metallic state due to many factors including carbon deposition and OC deactivation. Therefore, the effect of the initial reduction state on the OC oxidation in the air reactor is a significant parameter for consideration in developing the oxidation kinetic model. The objective of this work is to develop a physically significant kinetic model that applies to the oxidation of both initially fully and partially reduced OC with air. For this study, 1.5 mm Fe-based OC particle supported with TiO 2 was used as the model OC particle due to its complex multistep reaction nature. The oxidation kinetics were experimentally investigated in a thermogravimetric analyzer (TGA). Results indicate a significant difference in the oxidation rate profile for the OCs when oxidized from an initially fully reduced compared to an initially partially reduced state. Elemental mapping via energy-dispersive X-ray spectroscopy (EDS) reveals a shrinking-core type topochemical pattern across the OC particle, which was identified to be the cause of the dependency of kinetics on the initial reduction state. A generalized kinetic model was developed based on the observed shrinking-core behavior without presuming any rate-determining steps and experimentally validated over a broad range of temperatures (800–1000 °C) and oxygen concentrations (5, 7, 10, and 15 mol%). Impacts of particle porosity, size, and core-shell structure on the OC oxidation kinetics were analyzed in the developed oxidation kinetic model to suggest methods of improving the oxidation rate of the OC without modifying the chemical composition.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Solar-driven selective conversion of millimolar dissolved carbon to fuels with molecular flux generation

Abstract The direct utilization of dissolved inorganic carbon in seawater for CO 2 conversion promises chemical production on-demand and with zero carbon footprint. Photoelectrochemical (PEC) CO 2 reduction (CO 2 R) devices promise the sustainable conversion of dissolved carbon in seawater to carbon products using sunlight as the only energy input. However, the diffusion-dominant transport mechanism and the near-zero concentration of CO 2 (aq) (CO 2 dissolved in aqueous solution) in static seawater has made it extremely challenging to achieve high solar-to-fuel (STF) efficiency and high carbon-product selectivity. Here, where CO 2 (aq) as a reactant generated in situ by acidification of HCO 3 - flows continuously from BiVO 4 photoanodes to Si photocathodes, enabling a single-step conversion of dissolved carbon into products. Our PEC device significantly increases the CO selectivity from 3% to 21%, which approaches the 30% theoretical limit according to multi-physics modeling. Meanwhile, the Si/BiVO 4 PEC CO 2 R device achieved a STF efficiency of 0.71%. Such flow engineering achieves flow-dependent selectivity, rate, and stability in simulated seawater, thus promising practical solar fuel production at scale.

Liu, Bin↗
DOE OSTI2021

Rotating Detonation Engine Introduction [Webinar]

Turning a constant pressure combustor into a constant volume combustor changes it from a Brayton Cycle into a Humphrey Cycle. This allows it to extract more work from the fuel, increasing efficiency and reducing emissions. One way to create a constant volume combustor is by using a rotation detonation engine that introduces air and fuel continuously.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2020

Hierarchical electrode design of highly efficient and stable unitized regenerative fuel cells (URFCs) for long-term energy storage

The unitized regenerative fuel cell (URFC) is a promising electrochemical device for intermittent renewable energy storage in chemical bonds. However, widespread application has been hindered due to low round-trip efficiencies (RTEs) and disappointing durability, in particular at high rates. In this study, we break through that barrier by demonstrating highly efficient, flexible, and stable URFCs via hierarchical design of the multiscale catalyst-layer structures. A more porous and less tortuous Pt and Ir catalyst layer is realized using a doctor blade fabrication method that significantly improves URFC performance. We demonstrate RTEs of 56% and 53% under constant-electrode and constant-gas mode, respectively, while operating at 1000 mA cm –2 , and significantly, a RTE of 45% at 2000 mA cm –2 , achievements that were previously viewed as unfeasible under the onerous demands of URFC operation. At the same time we demonstrate URFCs under both constant-electrode and constant-gas mode operated continuously for over 500 h with negligible degradation. These results demonstrate the viability of applying URFCs for long-term energy storage at previously unattainable efficiencies and cast new light on electrode design and optimization of URFCs.

25 ENERGY STORAGE↗
DOE OSTI2020

Nanotechnology for catalysis and solar energy conversion

This roadmap on Nanotechnology for Catalysis and Solar Energy Conversion focuses on the application of nanotechnology in addressing the current challenges of energy conversion: 'high efficiency, stability, safety, and the potential for low-cost/scalable manufacturing' to quote from the contributed article by Nathan Lewis. This roadmap focuses on solar-to-fuel conversion, solar water splitting, solar photovoltaics and bio-catalysis. It includes dye-sensitized solar cells (DSSCs), perovskite solar cells, and organic photovoltaics. Smart engineering of colloidal quantum materials and nanostructured electrodes will improve solar-to-fuel conversion efficiency, as described in the articles by Waiskopf and Banin and Meyer. Semiconductor nanoparticles will also improve solar energy conversion efficiency, as discussed by Boschloo et al in their article on DSSCs. Perovskite solar cells have advanced rapidly in recent years, including new ideas on 2D and 3D hybrid halide perovskites, as described by Spanopoulos et al 'Next generation' solar cells using multiple exciton generation (MEG) from hot carriers, described in the article by Nozik and Beard, could lead to remarkable improvement in photovoltaic efficiency by using quantization effects in semiconductor nanostructures (quantum dots, wires or wells). These challenges will not be met without simultaneous improvement in nanoscale characterization methods. Terahertz spectroscopy, discussed in the article by Milot et al is one example of a method that is overcoming the difficulties associated with nanoscale materials characterization by avoiding electrical contacts to nanoparticles, allowing characterization during device operation, and enabling characterization of a single nanoparticle. Besides experimental advances, computational science is also meeting the challenges of nanomaterials synthesis. The article by Kohlstedt and Schatz discusses the computational frameworks being used to predict structure–property relationships in materials and devices, including machine learning methods, with an emphasis on organic photovoltaics. The contribution by Megarity and Armstrong presents the 'electrochemical leaf' for improvements in electrochemistry and beyond. In addition, biohybrid approaches can take advantage of efficient and specific enzyme catalysts. These articles present the nanoscience and technology at the forefront of renewable energy development that will have significant benefits to society.

14 SOLAR ENERGY↗
DOE OSTI2021

SOFC Prototype System Test

The goal of this U.S. Department of Energy (DOE) sponsored project is to test a 200 kWe thermally self-sustaining atmospheric-pressure solid oxide fuel cell (SOFC) prototype system at a prominent site. Fuel Cell Energy Inc. (FCE) utilized the state-of-the-art SOFC technology of its wholly-owned subsidiary Versa Power Systems (VPS) to design, fabricate and test the 200 kW prototype system. The specific objectives of this project were to achieve an SOFC stack power degradation rate of ≤1.5% per 1000 hours for the 400 kW stand-alone prototype power system undergoing ≥ 5000 hours of steady state tests at thermally self-sustained normal operating conditions (NOC), and to verify the prospects for a high volume SOFC stack production cost below the DOE target of 225 dollars per kilowatt. Achieving these goals enables commercial natural gas fueled SOFC system deployment in the 2020 timeframe, which will eventually lead to SOFC technology that is viable for large scale central power generation applications.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2026

DieselGen.jl

SAND2026-22947O DieselGen.jl is a Julia tool for diesel-engine generator sizing and performance simulation. It provides a standalone implementation of FASTSim-style diesel fuel-converter behavior with differentiable efficiency and fuel-consumption calculations. Sandia National Laboratories is a multimission laboratory managed and operated by National Technology & Engineering Solutions of Sandia, LLC, a wholly owned subsidiary of Honeywell International Inc., for the U.S. Department of Energy’s National Nuclear Security Administration under contract DE-NA0003525.

Michelen Strofer, Carlos [Sandia National Lab. (SN↗
DOE OSTI2023

Development and evaluation of a skeletal mechanism for EHN additized gasoline mixtures in large Eddy simulations of HCCI combustion

Advanced Low Temperature Combustion modes, such as the Sandia proposed Additive-Mixing Fuel Injection (AMFI), can unlock significant potential to boost fuel conversion efficiency and ultimately improve the energy conversion of internal combustion engines. This is a novel improved combustion process that is enabled by supplying small (<5%) variable amounts of autoignition improver to the fuel to enhance the engine operation and control. Common, diesel-fuel ignition-quality enhancing additive, 2-ethylexyl nitrate (EHN), is doped into gasoline to enable Sandia LTGC + AMFI combustion. This manuscript focuses on the development of a reduced sub-mechanism for EHN chemical kinetics at engine relevant conditions that is implemented into a skeletal mechanism for chemical kinetic studies of gasoline surrogate fuels. The mechanism validation utilized zero-dimensional numerical simulations and comparison to shock tube ignition-delay data of pure and EHN-doped n-heptane. Additional validation is presented with Homogeneous Charge Compression-Ignition (HCCI) engine data of pure and EHN-doped research-grade E10 gasoline. Then, the mechanism was deployed in a 3-D computational fluid dynamics (CFD) using Large Eddy Simulations (LES) to model the HCCI engine experiments of 0.4% vol EHN additized E10 gasoline at several equivalence ratios. Simulations showed a very good performance of the mechanism, and the model accurately reproduced (a) the ignition point, (b) combustion phasing, (c) combustion duration, and (d) the peak of the heat release rates of the engine experiments. The results show that EHN promotes Low-Temperature Heat Release, ultimately driving the gasoline to autoignite at thermodynamic conditions where the fuel would not otherwise ignite. Overall, this work demonstrates a viable reduced chemical-kinetic mechanism for EHN and shows that it can be combined with a skeletal gasoline mechanism for CFD-LES analysis of well-mixed LTGC that matches well with experimental results. The CFD-LES analysis also shows the spatial distribution of EHN-fuel interactions that control the autoignition throughout the combustion chamber.

Guleria, Gaurav↗
DOE OSTI2026

Finite-element-based simulations of electrodes for CO 2 cascade reduction reactions

The multielectron reduction of CO 2 to liquid fuels could be a path to scalable energy storage, but reaching this goal requires major advances in catalysis and systems engineering. Cascade catalysis, which couples sequential reactions without isolating intermediates, has emerged as a promising route to enhance selectivity and efficiency in CO 2 reduction (CO 2 R). In this review, we examine how finite-element-based simulations of continuum model [finite element method (FEM)] approaches are being used to analyze and guide CO 2 R cascade systems. We first outline the fundamentals of cascade catalysis and recent advances in catalytic materials (metallic, molecular, and hybrid architectures). We then focus on FEM developments at the electrode and device scales, emphasizing how these models capture transport phenomena, local microenvironments, and geometry-dependent effects. To clarify design principles, we present case studies of cascade electrodes organized in systems without and with integrated semiconductors. We further emphasize the integration of FEM with multiscale frameworks (density functional theory, molecular dynamics, kinetic Monte Carlo) and its role in bridging atomic-level insights with device-level performance. Finally, we identify current limitations and future prospects, including improved boundary conditions, coupling with operando experiments, and machine learning-accelerated model development. Together, these insights provide design principles for next-generation CO 2 R cascade systems for efficient solar fuel production.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Enabling Low-Temperature (LTP) Ignition Technologies for Multi-Mode Engines through the Development of a Validated High-Fidelity LTP Model for Predicative Simulations Tools

The goal of multi-mode engine architectures is to extend current lean-burn dilution limits with renewable fuels, which requires spark plugs to deposit high energies (hundreds of mJ) in order to initiate ignition and complete combustion. At elevated energy deposition rates, spark plugs experience increased electrode erosion and thermal losses, which ultimately shortens the spark-plug lifetime and lowers ignition efficiency. As such, in order to safeguard the efficiency gains of multi-mode concepts, new and improved ignition technologies are required. Recently, non-equilibrium low-temperature plasmas (LTP) have been shown to promote energy-efficient ignition via quenching and transport of electronically excited atoms and molecules, selective radical production and fast heating of hydrocarbon/air mixtures [1-2]. Thus, LTP is seen as a technology that can potentially improve the energy extraction efficiency of fuels, while enabling kinetically controlled combustion modes towards fuel leaner conditions to realize current DOE VTO goals of improving the sustainability of future mobility [3]. Although many previous studies have demonstrated the efficacy of plasma-assisted ignition to enhance combustion, the detailed enhancement mechanisms remain largely unknown, especially for oxygenated fuels and at elevated pressures that are most relevant to practical engine conditions. These barriers hinder the development of accurate and comprehensive numerical models that seek to describe LTP-based ignition in existing engine design software tools and methods. Current state-of-the-art simulation capabilities for LTP ignition systems are in need of improvements since they deliver qualitative results only due to important limitations of existing approaches. Firstly, validated kinetic models with elementary steps for plasma discharges in oxygenated fuel/air mixtures of relevance to the transportation sector are required. Such kinetic models do not exist at present and will be developed and validated within this project. Secondly, plasma discharges and reactive mixture ignition are multi-scale, unsteady processes requiring high-performance numerical methods and software that execute efficiently on DOE supercomputers. Such software does not exist at present and will be developed and applied to practical LTP ignition scenarios as part of this project. Thirdly, experimental databases that are tailored to serve as benchmark in support of the development of predictive computational models of LTP ignition do not exist and will be part of this project.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

Roundtable on Foundational Science for Carbon-Neutral Hydrogen Technologies (Technology Status Document)

This document summarizes the status of carbon-neutral hydrogen production, storage and transport, and utilization. The state of the art in the implementation, limitations, and challenges of these technologies are summarized. Sources of hydrogen are broadly categorized as hydrcoarbons or water and the processes used to convert these sources to hydrogen as catalytic, thermochemical, or electrochemical. Catalytic steam methane reforming of methane is the dominant process today. Other processes have smaller production volumes and the technology is less mature, but are being deployed at increasing rates, most notably water electrolyzers for hydrogen fueling stations. Efficient transport and storage of hydrogen is one of the major challenges facing a hydrogen-based energy economy. This arises in part from its low volumetric energy density necessitating very high pressures or cryogenic temperatures to store sufficient amounts for practical applications. High-pressure compressed hydrogen cylinders are the incumbent hydrogen storage technology for applications such as light-duty fuel cell electric vehicles, for example. The storage of hydrogen in materials or in chemicals is being pursued to address the issues associated with compression, such as parasitic energy loss and weight, size, and cost of storage containers. The complex nature of the chemical and physical processes involved in the uptake, storage, and release of hydrogen has slowed the discovery of suitable hydrogen storage materials. Both small and large-scale storage face the challenge of embrittlement of the storage media by hydrogen. There is a myriad of uses of hydrogen offering the promises of improving the efficiency of various applications and reducing or eliminating CO 2 emissions. These range from direct electrochemical conversion to electricity to power vehicles and grid-level stationary applications to combustion to production of chemicals and commodities. One of the most impactful applications in terms of reduction of CO 2 emissions is fuel cell passenger vehicles and heavy-duty vehicles such as class 8 trucks. The challenges facing widespread deployment of fuel cells, beyond the major hurdle of the lack of a hydrogen distribution infrastructure, are cost and durability, primarily related to the precious metal cathode catalyst and its durability. The other uses of hydrogen from conversion to hydrocarbons, polymer upcycling, and upgrading of bio-oils are at varying stages of maturity and also face fundamental challenges associated with catalytic processes and materials.

08 HYDROGEN↗
DOE OSTI2021

Transformative Materials for High-Efficiency Thermochemical Production of Solar Fuels (Final Report)

Metal oxide-based two-step solar thermochemical (STC) H 2 O and CO 2 -splitting cycles are a promising route to convert solar thermal energy into fuels. The metal oxide materials are reduced at high temperatures (Step 1), and then at low (but still elevated) temperatures, the reduced oxide is used to split H 2 O or CO 2 (Step 2). However, current applications of these cycles are limited by the efficiency of the metal oxide materials. A lower temperature for reduction is desirable, but that brings a concomitant reduction in the driving force for gas splitting. So, designing novel, high-efficiency materials is challenging. Here, we devised and performed a joint computational-experimental project, combined with materials design strategies and high-throughput approaches with the goal to quickly discover and demonstrate novel thermochemical materials with superior properties. Our approach involves an active feedback loop between experimental and computational research. We have use our previously developed materials design map, to efficiently screen results from high-throughput first- principles computation to predict new compositions and subsequently to experimentally study the properties of novel, predicted materials. Experimental measurements of the thermodynamic properties of selected materials serve as a critical benchmark, not only in evaluating the STCH properties of synthesized compounds, but also serving as a validation dataset for computational approaches. We experimentally explored a set of predicted ABO3 perovskites and focus on obtaining high quality thermodynamic properties for validation of computational prediction of enthalpy and entropy of reduction. These thermodynamic quantities play a major role in designing materials with reduced temperatures of reduction but sufficient gas-splitting rates. Finding good validation between experimental and computational data for enthalpies of reduction, we turn to promising ABO3 materials modified by A and B site substitutions, opening an enormous combinatorial space of materials. We use our high-throughput approach to “tune in” the desired solar thermochemical (STC) properties for STC. This vast composition space can only be reasonably explored using the high-throughput approaches, both computational and experimental, of this proposal. Several promising novel oxide materials have been predicted, synthesized, and verified using our materials design approach.

08 HYDROGEN↗
DOE OSTI2020

Update on the United States Advanced Ultra-Supercritical Program with Full Scale Component Fabrication to Develop Utility Scale Power Plants with 760°C Steam Temperature

Following the successful completion of a 15-year effort to develop and test materials that would allow coal-fired power plants to be operated at advanced ultra-supercritical (A-USC) steam conditions, a United States-based consortium is presently engaged in Phase 2 of a project which includes an advanced manufacturing effort to complete US-based supply chain development for full commercial scale (800-850 MWe) A-USC components made of nickel-based alloys, components operating at up to 760°C. The project, funded under U.S. Department of Energy Award No. DE-FE0025064, falls under the US DOE overall goal to Develop cost-effective, reliable technologies to improve the efficiency of new and existing coal-fired power plants. A-USC steam cycles have the potential to improve cycle efficiency, reduce fuel costs, and reduce greenhouse gas emissions. Current development and demonstration efforts are focused on enabling the construction of A-USC plants, operating with steam temperatures as high as 1400°F (760°C) and steam pressures up to 5000 psi (35 MPa), which can potentially increase cycle efficiencies to 47% HHV (higher heating value), or approximately 50% LHV (lower heating value), and reduce CO 2 emissions by roughly 25%, compared to today’s U.S. fleet. A-USC technology provides a lower-cost method to reduce CO 2 emissions, compared to CO 2 capture technologies, while retaining a viable coal option for owners of coal generation assets. Among the specific goals of Phase 2 of the ComTest Project are to: validate that components made from advanced nickel-based alloys can operate and perform under A-USC conditions accelerate the development of a U.S.-based supply chain for the full complement of A-USC components close the remaining gaps and reduce the risks for manufacturing components from advanced materials for commercial demonstration fabricate full-scale versions of selected key components made of nickel-based alloys validate a qualified U.S. supply chain, to provide greater cost certainty for components obtain American Society of Mechanical Engineers (ASME) code approval for new materials, components and processes Additional benefit: Manufacturing technology will be applicable to other advanced fossil energy high temperature cycles, and can support increased flexibility of existing power plants The ComTest project is managed by Energy Industries of Ohio, and technically directed by the Electric Power Research Institute, Inc., with General Electric designing the A-USC components. As stated earlier, the current phase of the effort is primarily funded by the U.S. Department of Energy, through the National Energy Technology Laboratory. This presentation outlines the motivation for the project, explains the project’s structure and schedule, and provides some of the technical details on the design of the ComTest components.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2020

Update on the United States Advanced Ultra-Supercritical Program with Full Scale Component Fabrication to Develop Utility Scale Power Plants with 760°C Steam Temperature

Following the successful completion of a 15-year effort to develop and test materials that would allow coal-fired power plants to be operated at advanced ultra-supercritical (A-USC) steam conditions, a United States-based consortium is presently engaged in Phase 2 of a project which includes an advanced manufacturing effort to complete US-based supply chain development for full commercial scale (800-850 MWe) A-USC components made of nickel-based alloys, components operating at up to 760°C. The project, funded under U.S. Department of Energy Award No. DE-FE0025064, falls under the US DOE overall goal to Develop cost-effective, reliable technologies to improve the efficiency of new and existing coal-fired power plants. A-USC steam cycles have the potential to improve cycle efficiency, reduce fuel costs, and reduce greenhouse gas emissions. Current development and demonstration efforts are focused on enabling the construction of A-USC plants, operating with steam temperatures as high as 1400°F (760°C) and steam pressures up to 5000 psi (35 MPa), which can potentially increase cycle efficiencies to 47% HHV (higher heating value), or approximately 50% LHV (lower heating value), and reduce CO 2 emissions by roughly 25%, compared to today’s U.S. fleet. A-USC technology provides a lower-cost method to reduce CO 2 emissions, compared to CO 2 capture technologies, while retaining a viable coal option for owners of coal generation assets. Among the specific goals of Phase 2 of the ComTest Project are to: validate that components made from advanced nickel-based alloys can operate and perform under A-USC conditions accelerate the development of a U.S.-based supply chain for the full complement of A-USC components close the remaining gaps and reduce the risks for manufacturing components from advanced materials for commercial demonstration fabricate full-scale versions of selected key components made of nickel-based alloys validate a qualified U.S. supply chain, to provide greater cost certainty for components obtain American Society of Mechanical Engineers (ASME) code approval for new materials, components and processes Additional benefit: Manufacturing technology will be applicable to other advanced fossil energy high temperature cycles, and can support increased flexibility of existing power plants The ComTest project is managed by Energy Industries of Ohio, and technically directed by the Electric Power Research Institute, Inc., with General Electric designing the A-USC components. As stated earlier, the current phase of the effort is primarily funded by the U.S. Department of Energy, through the National Energy Technology Laboratory. This presentation outlines the motivation for the project, explains the project’s structure and schedule, and provides some of the technical details on the design of the ComTest components.

01 COAL, LIGNITE, AND PEAT↗