Search NASA⌕ Search

SEARCH · Search NASA

Results for “Geometry”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

Molecular Geometry and Electronic Structure of Copper Corroles

Copper corroles are known for their unique multiconfigurational electronic structures in the ground state, which arise from the transfer of electrons from the π orbitals of the corrole to the d-orbital of copper. While density functional theory (DFT) provides reasonably good molecular geometries, the determination of the ground spin state and the associated energetics is heavily influenced by functional choice, particularly the percentage of the Hartree–Fock exchange. Using extended multireference perturbation theory methods (XMS-CASPT2), the functional choice can be assessed. The molecular geometries and electronic structures of both the unsubstituted and the meso-triphenyl copper corroles were investigated. A minimal active space was employed for structural characterization, while larger active spaces are required to examine the electronic structure. The XMS-CASPT2 investigations conclusively identify the ground electronic state as a multiconfigurational singlet (S o ) with three dominant electronic configurations in its lowest energy and characteristic saddled structure. In contrast, the planar geometry corresponds to the triplet state (T o ), which is approximately 5 kcal/mol higher in energy compared to the S o state for both the bare and substituted copper corroles. Notably, the planarity of the T o geometry is reduced in the substituted corrole compared with that in the unsubstituted one. By analyzing the potential energy surface (PES) between the S o and T o geometries using XMS-CASPT2, the multiconfigurational electronic structure is shown to transition toward a single electron configuration as the saddling angle decreases (i.e., as one approaches the planar geometry). Despite the ability of the functionals to reproduce the minimum energy structures, only the TPSSh-D 3 PES is reasonably close to the XMS-CASPT2 surface. Significant deviations along the PES are observed with other functionals.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Nanocrystal Geometry Governs Phase Transformation Pathways in Palladium Hydride

Pathways and structural dynamics of phase transformations impact performance of materials in energy and information storage technologies. Palladium hydride (PdH x ) nanocrystals are an ideal model system for studying solute-induced phase transformations, where elastic energy from lattice mismatch between α-PdH x and β-PdH x phases is often considered a key to determining the transformation pathways. α/β-PdH x interfacial elastic energy is affected by the confined geometry of a nanocrystal. However, how nanocrystal geometry influences phase transformation pathways is largely unknown. Using in situ liquid phase transmission electron microscopy, we directly visualize hydrogenation in Pd nanocrystals with two geometries, a nanocube and a hexagonal nanoplate. Both follow similar sequences of an initially curved nucleus, interface flattening, and reverse-stage nucleation; however, their evolving α/β-PdH x interfaces exhibit geometry-dependent crystallographic alignments. In nanocubes, {100}-aligned configurations conform to static elastic energy ordering, representing a pathway that maintains a local mechanical equilibrium, whereas nanoplates display both {110}- and {211}-aligned interfaces. Theoretical simulations show that geometry determines the accessibility of alternative phase transformation pathways as the system is driven far from equilibrium during hydrogenation. In conclusion, these findings identify geometry as a fundamental parameter for directing phase transformation pathways, offering design principles for accessing atypical configurations and improving properties of intercalation-based devices.

Lee, Daewon [Lawrence Berkeley National Laboratory↗

CASPT2 molecular geometries of Fe( II ) spin-crossover complexes

Using fully internally contracted (FIC)-CASPT2 analytical gradients, geometry optimizations of spin-crossover complexes are reported. This approach is tested on a series of Fe(II) complexes with different sizes, ranging from 13 to 61 atoms. A combination of active space and basis set choices are employed to investigate their role in determining reliable molecular geometries. The reported strategy demonstrates that a wave function-based level of theory can be used to optimize the geometries of metal complexes in reasonable times and enables one to treat the molecular geometry and electronic structure of the complexes using the same level of theory. For a series of smaller Fe(II) SCO complexes, strong field ligands in the LS state result in geometries with the largest differences between DFT and CASPT2; however, good agreement overall is observed between DFT and CASPT2. For the larger complexes, moderate sized basis sets yield geometries that compare well with DFT and available experimental data. Here we recommend using the (10e,12o) active space since convergence to a minimum structure was more efficient than with truncated active spaces despite having similar Fe–ligand bond distances.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The impact of thermoelectric leg geometries on thermal resistance and power output

Thermoelectric devices enable direct, solid-state conversion of heat to electricity and vice versa. Rather than designing the shape of thermoelectric units or legs to maximize this energy conversion, the cuboid shape of these legs has instead remained unchanged in large part because of limitations in the standard manufacturing process. However, the advent of additive manufacturing (a technique in which freeform geometries are built up layer-by-layer) offers the potential to create unique thermoelectric leg geometries designed to optimize device performance. This work explores this new realm of novel leg geometry by simulating the thermal and electrical performance of various leg geometries such as prismatic, hollow, and layered structures. The simulations are performed for two materials, a standard bismuth telluride material found in current commercial modules and a higher manganese silicide material proposed for low cost energy conversion in high-temperature applications. The results include the temperature gradient and electrical potential developed across individual thermoelectric legs as well as thermoelectric modules with 16 legs. Even simple hollow and layered leg geometries result in larger temperature gradients and higher output powers than the traditional cuboid structure. As a result, the clear dependence of thermal resistance and power output on leg geometry provides compelling motivation to explore additive manufacturing of thermoelectric devices.

30 DIRECT ENERGY CONVERSION↗

Torus geometry eigenfunctions of an interacting multi-Landau-level Hamiltonian

A short-ranged, rotationally symmetric multi-Landau-level model Hamiltonian for strongly interacting electrons in a magnetic field was proposed [A. Anand et al., Phys. Rev. Lett. 126, 136601 (2021)] with the key feature that it allows exact many-body eigenfunctions on the disk not just for quasiholes but for all charged and neutral excitations of the entire Jain sequence filling fractions. We extend this to geometries without full rotational symmetry, namely, the torus and cylinder geometries, and present their spectra. Exact diagonalization of the interaction on the torus produces the low-energy spectra at filling fraction v = n/(2⁢pn + 1) that is identical, up to a topological (2⁢pn + 1)-fold multiplicity, to that of the integer quantum Hall spectra at v = n, for the incompressible state as well as all excitations. While the ansatz eigenfunctions in the disk geometry cannot be generalized to closed geometries such as torus or sphere, we show how to extend them to cylinder geometry. Meanwhile, we show eigenfunctions for charged excitations at filling fractions between 1/3 and 2/5 can be written on the torus and the spherical geometries.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DES Y1 results: Splitting growth and geometry to test $\Lambda$CDM

We analyze Dark Energy Survey (DES) data to constrain a cosmological model where a subset of parameters—focusing on Ωm—are split into versions associated with structure growth (e.g., Ωmgrow) and expansion history (e.g., Ωmgeo). Once the parameters have been specified for the ΛCDM cosmological model, which includes general relativity as a theory of gravity, it uniquely predicts the evolution of both geometry (distances) and the growth of structure over cosmic time. Any inconsistency between measurements of geometry and growth could therefore indicate a breakdown of that model. Our growth-geometry split approach therefore serves both as a (largely) model-independent test for beyond-ΛCDM physics, and as a means to characterize how DES observables provide cosmological information. We analyze the same multiprobe DES data as [Phys. Rev. Lett. 122, 171301 (2019)PRLTAO0031-900710.1103/PhysRevLett.122.171301] : DES Year 1 (Y1) galaxy clustering and weak lensing, which are sensitive to both growth and geometry, as well as Y1 BAO and Y3 supernovae, which probe geometry. We additionally include external geometric information from BOSS DR12 BAO and a compressed Planck 2015 likelihood, and external growth information from BOSS DR12 RSD. We find no significant disagreement with Ωmgrow=Ωmgeo. When DES and external data are analyzed separately, degeneracies with neutrino mass and intrinsic alignments limit our ability to measure Ωmgrow, but combining DES with external data allows us to constrain both growth and geometric quantities. We also consider a parametrization where we split both Ωm and w, but find that even our most constraining data combination is unable to separately constrain Ωmgrow and wgrow. Relative to ΛCDM, splitting growth and geometry weakens bounds on σ8 but does not alter constraints on h.

79 ASTRONOMY AND ASTROPHYSICS↗

Numerical Model Development of a Variable-Geometry Attenuator Wave Energy Converter

Because the wave energy industry is still in its infancy, an optimal design for wave energy converters (WECs) has yet to be established; more work is needed to explore various cost-reduction pathways. The primary cost-reduction pathway considered for this work is the optimization of the geometric profile on an attenuator WEC to maximize power production while, at the same time, minimizing capital expenditures through the use of variable-geometry modules. In this investigation, the variable-geometry modules consist of inflatable bags placed on either side of a base central steel cylinder that would be inflated in low-moderate sea states to maximize power capture and then deflated in moderate-extreme sea states to minimize wave loading. The numerical model and simulation of the attenuator WEC were developed and completed using WEC-Sim, which is an open-source code that is appropriate for use in evaluating the dynamic response of the different WEC models in operational seas. The power production estimates were obtained from the Wave Energy Prize (WEP) sea states, which are representative of U. S. deployment sites, to calculate the average climate capture width that is used in the WEP ACE calculation. Preliminary capital expenditure costs were obtained assuming the base central steel cylinder mass was equal to the fluid displaced mass, minus the mass of the variable-geometry bags. The additional weight required to offset the additional buoyancy from the variable-geometry bags was assumed to come from the addition of seawater ballast. The variable-geometry attenuator model was found to have a similar power capture efficiency as a fixed-body model, but is expected to have a lower characteristic capital expenditure given its more streamlined profile, which demonstrates that variable-geometry modules may provide a realistic cost-reduction pathway to help design a more cost-competitive WEC.

50 EE - Wind and Water Power Program - Water (EE-4↗

SU-G-TeP3-02: Determination of Geometry-Specific Backscatter Factors for Radiobiology Studies

Purpose: Radiation biology research relies on an accurate radiation dose delivered to the biological target. Large field irradiations in a cabinet irradiator may use the AAPM TG-61 protocol. This relies on an air-kerma measurement and conversion to absorbed dose to water (Dw) on the surface of a water phantom using provided backscatter factors. Cell or small animal studies differ significantly from this reference geometry. This study aims to determine the impact of the lack of full scatter conditions in four representative geometries that may be used in radiobiology studies. Methods: MCNP6 was used to model the Dw on the surface of a full scatter phantom in a validated orthovoltage x-ray reference beam. Dw in a cylindrical mouse, 100 mm Petri dish, 6-well and 96-well cell culture dishes was simulated and compared to this full scatter geometry. A reference dose rate was measured using the TG-61 protocol in a cabinet irradiator. This nominal dose rate was used to irradiate TLDs in each phantom to a given dose. Doses were obtained based on TLDs calibrated in a NIST-traceable beam. Results: Compared to the full scattering conditions, the simulated dose to water in the representative geometries were found to be underestimated by 12-26%. The discrepancy was smallest with the cylindrical mouse geometry, which most closely approximates adequate lateral- and backscatter. TLDs irradiated in the mouse and petri dish phantoms using the TG-61 determined dose rate showed similarly lower values of Dw. When corrected for this discrepancy, they agreed with the predicted Dw within 5%. Conclusion: Using the TG-61 in-air protocol and given backscatter factors to determine a reference dose rate in a biological irradiator may not be appropriate given the difference in scattering conditions between irradiation and calibration. Without accounting for this, the dose rate is overestimated and is dependent on irradiation geometry.

60 APPLIED LIFE SCIENCES↗

Spray characterization for engine combustion network Spray G injector using high-fidelity simulation with detailed injector geometry

This article presents a computational fluid dynamics study of the engine combustion network Spray G, focusing on the transient characteristics of the spray during the start of injection and the impacts of nozzle geometry details derived from the manufacturing process. The large-eddy-simulation method, coupled with the volume-of-fluid method, was used to model the high-speed turbulent two-phase flow. A moving-needle boundary condition was applied to capture the internal flow boundary condition accurately. The injector geometry was measured with micron-level resolution using X-ray tomographic imaging at the Advanced Photon Source at Argonne National Laboratory, providing detailed machining tolerance and defects from manufacturing and a realistic rough surface. For comparison, a nominal geometry and a modified geometry incorporating measured large-scale geometric features but no surface details were also used in the simulations. Spray characteristics such as mass flow rate, injection velocity, and Sauter mean diameter were analyzed. Significantly distinct spray characteristics in terms of injection velocity, spray morphology, and primary breakup mechanism were predicted using different nozzle geometries, which is mainly attributable to the realistic surface finish and manufacturing defects. The measured high-resolution geometry predicts a lower injection velocity, a wider-spreading spray, and an overall slower breakup rate with evident injector tip wetting compared to the ideally smooth nozzle boundary. This result implies that the manufacturing details of the injector, which are usually ignored in fuel injection studies, have a significant impact on the spray development process and should be taken into account for design optimization.

Yue, Zongyu↗

Influence of sweeping detonation-wave loading on damage evolution during spallation loading of tantalum in both a planar and curved geometry

Widespread research over the past five decades has provided a wealth of experimental data and insight concerning the shock hardening, damage evolution, and the spallation response of materials subjected to square-topped shock-wave loading profiles. However, fewer quantitative studies have been conducted on the effect of direct, in-contact, high explosive (HE)-driven Taylor wave (unsupported shocks) loading on the shock hardening, damage evolution, or spallation response of materials. Systematic studies quantifying the effect of sweeping-detonation wave loading are yet sparser. In this study, the damage evolution and spallation response of Ta is shown to be critically dependent on the peak shock stress, the geometry of the sample (flat or curved plate geometry), and the shock obliquity during sweeping-detonation-wave shock loading. Sweepingwave loading in the flat-plate geometry is observed to: a) yield a lower spall strength than previously documented for 1-D supported-shock-wave loading, b) exhibit increased shock hardening as a function of increasing obliquity, and c) lead to an increased incidence of deformation twin formation with increasing shock obliquity. Sweeping-wave loading of a 10 cm radius curved Ta plate is observed to: a) lead to an increase in the shear stress as a function of increasing obliquity, b) display a more developed level of damage evolution, extensive voids and coalescence, and lower spall strength with obliquity in the curved plate than seen in the flat-plate sweeping-detonation wave loading for an equivalent HE loading, and c) no increased propensity for deformation twin formation with increasing obliquity as seen in the flat-plate geometry. The overall observations comparing and contrasting the flat versus curved sweeping-wave spall experiments with 1D loaded spallation behavior suggests a coupled influence of obliquity and geometry on dynamic shock-induced damage evolution and spall strength. Coupled experimental and modeling research to quantify the combined effects of sweeping-wave loading with increasingly complex sample geometries on the shockwave response of materials is clearly crucial to providing the basis for developing and thereafter validation of predictive modeling capability.

36 MATERIALS SCIENCE↗

The MCNP6 Book On Unstructured Mesh Geometry: User's Guide for MCNP 6.2.1

Los Alamos National Laboratory’s (LANL) Monte Carlo N-Particle R (MCNP R ) transport code has a more general geometry capability than has been available in most combinatorial geometry codes [1]. In addition to the capability of combining several predefined geometric bodies, as in a combinatorial scheme, MCNP6 [2] gives the user the added flexibility of defining geometric regions from all the first and second degree surfaces of analytical geometry and elliptical tori and then combining them with Boolean operators. This decades-old constructive solid geometry (CSG) capability has been well-tested and verified. However, it has long been recognized that as the model complexity increases, this process of describing the geometry is difficult, tedious, time-consuming, and error prone[3, 4, 5]. Consequently, innovators have taken on the task of developing a better way to construct geometries, not only in MCNP6, but other particle transport codes as well

97 MATHEMATICS AND COMPUTING↗

Optimal Geometry for Focused Ion Beam-Milled Samples for Direct-Pull Micro-Tensile Testing Performed In Situ in a Scanning Electron Microscope

A thorough procedure was developed to efficiently manufacture dogbone samples using focused ion beam (FIB) milling for micro-tensile testing. A Bruker PI 89 PicoIndenter, Billerica, MA, USA, was used as a case study, although the analysis and results are applicable to other micro-mechanical testing systems capable of mounting a standard, Ø12.7 mm × Ø3.2 mm pin, scanning electron microscopy (SEM) pin stub (Ted Pella, Redding, CA, USA). Nine dogbones were made from an Fe-45Cu alloy additively manufactured using powder-fed laser-directed energy deposition (DED-LB). Testing showed that fracture was confined to the gauge section for all dogbones and that the fracture mode, ductile vs. brittle, was entirely dependent on the grain orientation relative to the loading direction. The analysis showed that the measured plastic strain to failure can vary from >11% (optimal geometry) to <1% (non-optimal geometry) in micro-tensile testing of high-tensile-strength (>1 GPa) metallic materials. Subsequently, a finite element analysis (FEA) was conducted to identify the improved dogbone geometries. A total of ten thousand dogbone geometries were tested, and their dimensions were defined by a set of four adjustable parameters (corner radius, load surface angle, load surface length, and dogbone head length). The gauge width and gauge length were fixed to 4 µm and 10 µm, respectively. Three-dimensional surface plots of the stress concentration as a function of two parameters were used to identify the optimal ranges of parameter values. The addition of maximum width and length constraints, measuring 25 µm and 30 µm, respectively, allowed us to identify an optimal geometry at load surface angles of 30° and 45°. Their respective dimensions (corner radius, load surface length, and dogbone head length) are, in µm, 12, 6, and 7 and 10, 7, and 7. Testing these two optimal geometries with a range of gauge lengths from 4 to 20 µm showed that smaller gauge lengths only slightly reduced the detrimental stress concentration outside the gauge section. However, smaller gauge lengths will notably improve the FIB surface polishing step as tapering is reduced with smaller dogbone lengths.

Chemistry↗

Use of interactive graphics to analyze QUICK-geometry: Supplement

The advantages of using interactive computer graphics to display aircraft geometry to aid in detection and analysis of errors are described. The QUICK geometry system is reviewed and the Quick Interactive Graphics Analysis (QUIAGA) program is described. This QUIAGA program was developed to exercise the QUICK geometry subroutines to examine in several modes on a graphics terminal. Its use in the detection and analysis of errors in the QUICK geometry definition can be of great assistance in speedily arriving at a correct analytical geometry description for flow field computation. Experience with the program in developing a QUICK geometry model of the NASA Space Shuttle Orbiter is used to show some of its features. Appendixes giving details of program usage and an example session are included.

Townsend, J. C.↗

An interactive approach to surface-fitting complex geometries for flowfield applications

Numerical flowfield methods require a geometry subprogram which can calculate body coordinates, slopes, and radii of curvature for typical aircraft and spacecraft configurations. The objective of this paper is to develop a new surface-fitting technique which addresses two major problems with existing geometry packages: computer storage requirements and the time required of the user for the initial set-up of the geometry model. In the present method, coordinates of cross sections are fit in a least-squares sense using segments of general conic sections. After fitting each cross section, the next step is to blend the cross-sectional curve-fits in the longitudinal direction using general conics to fit specific meridional half-planes. For the initial setup of the geometry model, an interactive, completely menu-driven computer code has been developed to allow the user to make modifications to the initial fit for a given cross section or meridional cut. Graphic displays are provided to assist the user in the visualization of the effect of each modification. The completed model may be viewed from any angle using the code's three-dimensional graphics package. Geometry results for the modeling of the Space Shuttle and a proposed Aeroassist Flight Experiment (AFE) geometry are presented, in addition to calculated heat-transfer rates based on these models.

Dejarnette, Fred R.↗

Effect of magnetic field geometry on the wave signature of the pickup of interstellar neutrals

By using the technique of Johnstone et al. (1991), the asymptotic wave spectrum induced by the pickup of interstellar ions in the heliosphere is derived. This approach is independent of quasi-linear theory. The asymptotic wave spectrum is calculated from the standard resonance condition by assuming that the asymptotic ion distribution is bispherical and by using conservation of energy. The calculation places no restriction on either the ratio of Alfven speed to solar wind flow speed or the particle pitch angle. Spectra for various geometries (relative orientations of the magnetic field and solar wind velocity) are calculated. Absolute upper limits to the expected wave enhancements are calculated. These upper limits are compared to the background fluctuation spectrum extrapolated from 0.87 AU, assuming a spectral index of -5/3 and radial dependences of -2 and -3. The heliocentric radial distances at which the peaks in the various geometry-dependent wave spectra are expected to be observable above the background are identified. Peaks due to pickup hydrogen at the proton gyrofrequency are found to be always stronger relative to the background in parallel than in perpendicular geometries. The parallel-geometry excitations consist only of sunward propagating waves. In perpendicular geometries a peak also occurs, this time near 0.1 of the proton gyrofrequency (corresponding to the peak calculated by Lee and Ip (1987)). However, the steep spectral dependence of the ambient wave field makes it unlikely that this peak will be observed inside 20 AU. A similar result holds for the case of pickup-helium induced excitation at the helium gyrofrequency. Inside 10 AU, peaks at these lower frequencies tend to be obscured by the steep frequency dependence (proportional to -5/3) of the ambient spectrum and then are only observable in parallel geometries.

Williams, L. L.↗

Computations of Viscous Flows in Complex Geometries Using Multiblock Grid Systems

Generating high quality, structured, continuous, body-fitted grid systems (multiblock grid systems) for complicated geometries has long been a most labor-intensive and frustrating part of simulating flows in complicated geometries. Recently, new methodologies and software have emerged that greatly reduce the human effort required to generate high quality multiblock grid systems for complicated geometries. These methods and software require minimal input form the user-typically, only information about the topology of the block structure and number of grid points. This paper demonstrates the use of the new breed of multiblock grid systems in simulations of internal flows in complicated geometries. The geometry used in this study is a duct with a sudden expansion, a partition, and an array of cylindrical pins. This geometry has many of the features typical of internal coolant passages in turbine blades. The grid system used in this study was generated using a commercially available grid generator. The simulations were done using a recently developed flow solver, TRAF3D.MB, that was specially designed to use multiblock grid systems.

Steinthorsson, Erlendur↗

Geometry Modeling for Unstructured Mesh Adaptation

The quantification and control of discretization error is critical to obtaining reliable simulation results. Adaptive mesh techniques have the potential to automate discretization error control, but have made limited impact on production analysis workflow. Recent progress has matured a number of independent implementations of flow solvers, error estimation methods, and anisotropic mesh adaptation mechanics. However, the poor integration of initial mesh generation and adaptive mesh mechanics to typical sources of geometry has hindered adoption of adaptive mesh techniques, where these geometries are often created in Mechanical Computer- Aided Design (MCAD) systems. The difficulty of this coupling is compounded by two factors: the inherent complexity of the model (e.g., large range of scales, bodies in proximity, details not required for analysis) and unintended geometry construction artifacts (e.g., translation, uneven parameterization, degeneracy, self-intersection, sliver faces, gaps, large tolerances be- tween topological elements, local high curvature to enforce continuity). Manual preparation of geometry is commonly employed to enable fixed-grid and adaptive-grid workflows by reducing the severity and negative impacts of these construction artifacts, but manual process interaction inhibits workflow automation. Techniques to permit the use of complex geometry models and reduce the impact of geometry construction artifacts on unstructured grid workflows are models from the AIAA Sonic Boom and High Lift Prediction are shown to demonstrate the utility of the current approach.

Park, Michael A.↗

Numerical Model Development of a Variable-Geometry Attenuator Wave Energy Converter: Preprint

Because the wave energy industry is still in its infancy, an optimal design for wave energy converters (WECs) has yet to be established; more work is needed to explore various cost reduction pathways. The primary cost-reduction pathway considered for this work is the optimization of the geometric profile on an attenuator WEC to maximize power production while, at the same time, minimizing capital expenditures through the use of variable-geometry modules. In this investigation, the variable geometry modules consist of inflatable bags placed on either side of a base central steel cylinder that would be inflated in low moderate sea states to maximize power capture and then deflated in moderate-extreme sea states to minimize wave loading. The numerical model and simulation of the attenuator WEC were developed and completed using WEC-Sim, which is an open-source code that is appropriate for use in evaluating the dynamic response of the different WEC models in operational seas. The power production estimates were obtained from the Wave Energy Prize (WEP) sea states, which are representative of U. S. deployment sites, to calculate the average climate capture width that is used in the WEP ACE calculation. Preliminary capital expenditure costs were obtained assuming the base central steel cylinder mass was equal to the fluid displaced mass, minus the mass of the variable-geometry bags. The additional weight required to offset the additional buoyancy from the variable-geometry bags was assumed to come from the addition of seawater ballast. The variable-geometry attenuator model was found to have a similar power capture efficiency as a fixed-body model, but is expected to have a lower characteristic capital expenditure given its more streamlined profile, which demonstrates that variable-geometry modules may provide a realistic cost-reduction pathway to help design a more cost-competitive WEC.

50 EE - Wind and Water Power Program - Water (EE-4↗