Search NASA⌕ Search

SEARCH · Search NASA

Results for “Graphite Characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

Compatibility of the Radio Frequency Mass Gauge with Graphite-Epoxy Composite Tanks

The radio frequency mass gauge (RFMG) is a low-gravity propellant quantity gauge being developed at NASA for possible use in long-duration space missions utilizing cryogenic propellants. As part of the RFMG technology development process, we evaluated the compatibility of the RFMG with a graphite-epoxy composite material used to construct propellant tanks. The key material property that can affect compatibility with the RFMG is the electrical conductivity. Using samples of 8552/IM7 graphite-epoxy composite, we characterized the resistivity and reflectivity over a range of frequencies. An RF impedance analyzer was used to characterize the out-of-plane electrical properties (along the sample thickness) in the frequency range 10 to 1800 MHZ. The resistivity value at 500 MHz was 4.8 ohm-cm. Microwave waveguide measurements of samples in the range 1.7 - 2.6 GHz, performed by inserting the samples into a WR-430 waveguide, showed reflectivity values above 98%. Together, these results suggested that a tank constructed from graphite/epoxy composite would produce good quality electromagnetic tank modes, which is needed for the RFMG. This was verified by room-temperature measurements of the electromagnetic modes of a 2.4 m diameter tank constructed by Boeing from similar graphite-epoxy composite material. The quality factor Q of the tank electromagnetic modes, measured via RF reflection measurements from an antenna mounted in the tank, was typically in the range 400 less than Q less than 3000. The good quality modes observed in the tank indicate that the RFMG is compatible with graphite-epoxy tanks, and thus the RFMG could be used as a low-gravity propellant quantity gauge in such tanks filled with cryogenic propellants.

Propellant tanks↗

Impact of high energy ball milling on the nanostructure of magnetite–graphite and magnetite–graphite–molybdenum disulphide blends

Different, partly complementary and partly redundant characterization methods were applied to study the transition of magnetite, graphite and MoS{sub 2} powders to mechanically alloyed nanostructures. The applied methods were: Transmission electron microscopy (TEM), Mössbauer spectroscopy (MS), Raman spectroscopy (RS), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). The main objective was to prepare a model material providing the essential features of a typical tribofilm forming during automotive braking, and to assess the impact of different constituents on sliding behaviour and friction level. Irrespective of the initial grain size, the raw materials were transferred to a nanocrystalline structure and mixed on a nanoscopic scale during high energy ball milling. Whereas magnetite remained almost unchanged, graphite and molybdenum disulphide were transformed to a nanocrystalline and highly disordered structure. The observed increase of the coefficient of friction was attributed to a loss of lubricity of the latter ingredient due to this transformation and subsequent oxidation. - Highlights: • Characterization of microstructural changes induced by high energy ball milling • Assessment of the potential of different characterization methods • Impact of mechanical alloying on tribological performance revealed by tests • Preparation of an artificial third body resembling the one formed during braking.

36 MATERIALS SCIENCE↗

Characterizing the surface compositions of supported bimetallic PtSn clusters: Effects of cluster-support interactions and surface adsorbates

PtSn bimetallic clusters on TiO2(110) and highly oriented pyrolytic graphite (HOPG) surfaces have been characterized by scanning tunneling microscopy, low energy ion scattering (LEIS), Xray photoelectron spectroscopy, and temperature programmed desorption (TPD); density functional theory (DFT) calculations have also been performed to better understand adsorption of CO and D2 on the PtSn surfaces. On TiO2 at coverages of 2 ML of Pt and 2 ML of Sn, exclusively bimetallic clusters are formed for both orders of deposition because clusters of the first metal completely cover the surface such that all atoms of the second metal are incorporated into the existing clusters. In contrast, on HOPG, the high mobility and weak cluster-support interactions on HOPG result in much larger 2 ML monometallic clusters (~30 Å high) that do not completely cover the surface, and deposition of the second metal produces larger clusters as well as smaller ones. Despite the difference in cluster morphologies for the different orders of deposition and supports, the LEIS experiments demonstrate that in all cases, the PtSn clusters are rich in Sn at the surface, as expected based on the lower surface free energy for Sn compared to Pt. Furthermore, the +0.2 eV shift in the Sn(3d5/2) binding energy observed on all surfaces in the presence of Pt is consistent with PtSn alloy formation. Deposition of 2 ML of Sn on TiO2 produces two-dimensional clusters with oxidation of Sn and reduction of titania at the clustersupport interface, but addition of Pt to the Sn clusters causes Sn to diffuse away from this interface, leaving Sn in the metallic state. TPD experiments on 2 ML Pt/TiO2 with increasing coverages of Sn show that the number of adsorption sites for D2 sharply decreases to nearly zero at 0.5 ML, while CO adsorption decreases to zero only at much higher Sn coverages of 2 ML. DFT studies for Sn modified Pt surfaces and bulk structures demonstrate that for CO adsorption at low Sn coverages (<0.25 ML), the strong Pt-CO interactions induce diffusion of Pt to the cluster surface and the formation of a bulk Pt3Sn alloy, whereas D2 adsorption does not lead to interactions with the Pt surface that are strong enough to induce alloy formation. A single Sn adatom prevents D2 adsorption on four neighboring Pt atoms via site-blocking and the donation of electron density to Pt.

Li, Fangliang↗

First approximations of phonon thermal transport at solid-graphite interfaces.

This model predicts thermal boundary conductance at interfaces where one material comprising the junction is characterized by high elastic anisotropy (i.e, graphite). The thermal properties of graphite are determined through a simplified vibrational model, where the bulk structure is treated as an linear assembly of two-dimensional systems. This model is validated at temperatures above cryogenic through comparison to experimentally determined values of specific heat. Elastic processes are accounted for through traditional diffuse transport theory. Inelastic contributions due to multi-phonon processes are also addressed and quantified.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Performance characterization of x-ray crystal spectroscopy highly oriented pyrolytic graphite reflectors based on x-ray diffractometry experiments

The use of Highly Oriented Pyrolytic Graphite (HOPG) reflectors is often proposed in the design of X-ray Crystal Spectroscopy (XCS) diagnostic systems for the next-generation tokamak devices, including the ITER project. Here, this study introduces an experimental study based on the X-Ray Diffractometry (XRD) method to evaluate the performance of HOPG reflectors. The experimental method provides both the angular responses and the reflectivities of the HOPG reflectors. A demonstrative XRD experiment is conducted, and the details of the experiment are introduced. This method enables precise studies on HOPG reflectors, facilitating the design of XCS diagnostic systems for future tokamaks.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Multiple Analytical Approach to Isotopic Transport Analysis in Magnetic Fusion Devices

High-Z impurities released from plasma-material interactions have been shown to limit the performance of fusion plasmas, and understanding these impurity transport mechanisms throughout the plasma scrape-off layer is a major challenge. Presented herein is a study of tungsten (W) erosion and transport by uniquely measuring absolute quantities of isotopic W in order to determine the source of natural and enriched 182W isotopes that have traveled throughout the tokamak discharges on the DIII-D National Fusion Facility at General Atomics. Two primary analysis methods have been implemented to characterize this W on graphite collector probes that were inserted into DIII-D’s outboard midplane. Results from experiments using Rutherford backscattering spectrometry (RBS) have measured W particle areal densities down the centerline of the probes as high as 6E14 atoms/cm2 with a detection limit of 1E12 atoms/cm2. Laser ablation inductively coupled plasma mass spectrometry (LAMS) has confirmed the elemental trends found with RBS and has provided additional insight into collector probe surface profiles. Two-dimensional elemental and isotopic maps from LAMS are used to reveal new collector probe features and further refine the source of collected W. Variations in isotopic profiles and total W content are coupled to (a) the face of the probe being analyzed, (b) the dimensions of the probe, and (c) the plasma pulse parameters that were used during probe exposure. These results provide one-of-a-kind empirical evidence that is now being utilized for validation of tokamak impurity transport through theoretical models and in codes such as 3D-LIM and OEDGE.

Duran, Jonah↗

AGC-2 Graphite Preirradiation Data Package

The NGNP Graphite R&D program is currently establishing the safe operating envelope of graphite core components for a Very High Temperature Reactor (VHTR) design. The program is generating quantitative data necessary for predicting the behavior and operating performance of the new nuclear graphite grades. To determine the in-service behavior of the graphite for pebble bed and prismatic designs, the Advanced Graphite Creep (AGC) experiment is underway. This experiment is examining the properties and behavior of nuclear grade graphite over a large spectrum of temperatures, neutron fluences and compressive loads. Each experiment consists of over 400 graphite specimens that are characterized prior to irradiation and following irradiation. Six experiments are planned with the first, AGC-1, currently being irradiated in the Advanced Test Reactor (ATR) and pre-irradiation characterization of the second, AGC-2, completed. This data package establishes the readiness of 512 specimens for assembly into the AGC-2 capsule.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

AGC-1 Irradiation Creep Strain Data Analysis

This Technical Memorandum (TM) fulfills milestone 4.2 of SOW-112178 “VHTR TDO GRAPHITE R&D – FY2014”, a level 2 deliverable due to the Department of Energy on September 30, 2014. Here we report the creep strain data and the analysis of the creep strain data from the irradiation creep capsule AGC-1 specimens that were supplied to ORNL. This is the first (prototype) of a series of five or six capsules planned as part of the Advanced Graphite Creep (AGC) experiment to fully characterize the neutron irradiation effects and radiation creep behavior of current nuclear graphites. The data reported include: specimen dimensions and hence the dimensional change upon irradiation. A comparison of these data for specimen matched pairs yields the creep strain; mass and volume, hence density. The creep strain analysis is by graphite grade. The AGC-1 capsule was irradiated in the Advanced Test Reactor (ATR) at INL at approximately 700°C and to a peak dose of 7 dpa (displacements per atom). The specimens final dose, temperature and stress conditions have been reported by INL1,2 are also tabulated here and used in the analysis.

Graphite Creep↗

AGC-1 Specimen Post Irradiation Data Report

Here we report the results of the Post Irradiation Examination (PIE) of the creep, control, and piggyback specimens from the irradiation creep capsule AGC-1. This is the first (prototype) of a series of six capsules planned as part of the Advanced Graphite Creep (AGC) experiment to fully characterize the neutron irradiation effects and radiation creep behavior of current nuclear graphites. The data reported include: specimen dimensions and hence the dimensional change upon irradiation (a comparison of these data for specimen matched pairs will yield the creep strain); mass and volume, hence density; elastic constants (Young’s modulus, shear modulus and Poisson’s ratio) from ultrasonic time of flight (TOF) and velocity measurements; Young’s modulus from the fundamental frequency of vibration; electrical resistivity; and thermal expansion from 100-550°C (hence coefficient of thermal expansion). Over 8500 individual physical measurement have been made and the data are reduced and reported here. The AGC-1 capsule was irradiated in the Advanced Test Reactor (ATR) at INL at approximately 700°C and to a peak dose of 7 dpa (displacements per atom). The specimen’s final dose, temperature and stress conditions have been reported by INL and are also tabulated here. Additionally the analysis of the SiC temperature monitors is reported. These temperature monitors were located along the center of the AGC-1 capsule and provide an independent assessment of the capsules final irradiation temperature. While all the PIE testing is reported (with the exception of the glued-end tensile strength specimens) additional analysis of the AGC data will be required to allow: 1. Improved fits to the existing models of graphite irradiation induced creep strain. 2. With the eventual advent of temperature dependency data from the additional AGC series of capsules, and microstructural data from piggy back specimens in AGC capsules, the development of new and improved models for the development of irradiation induced creep strain in graphite are anticipated. 3. An Investigation into the effects of creep strain on the physical properties of irradiated graphite.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Environmental effects on advanced composites

The development of titanium matrix composites for elevated temperature applications was investigated. General solutions for treating diffusion in multiphase multicomponent systems were studied. Graphite polyimide composites were characterized with respect to mechanical property degradation by moisture.

Unnam, J.↗

Material characterization and specification development for 350 F curing epoxy-graphite materials

New analytical techniques and a processability laminate have been used in the development of a material specification for 350 F curing epoxy-graphite materials. The development of the specification required the evaluation of prepregs which had variations in their processing behavior that were detected only in production. Chemical techniques were used to analyze the prepregs and establish limits on the concentrations of the various chemical constituents. A batch acceptance test laminate was designed to determine suitability of prepregs for production useage. The new specification requires that the processability laminate be ultrasonically and micrographically inspected for voids and porosity. Incorporation of these and other requirements will help to insure material consistency and processability.

Rogers, A. K.↗

Hot filament technique for measuring the thermal conductivity of molten lithium fluoride

Molten salts, such as lithium fluoride, are attractive candidates for thermal energy storage in solar dynamic space power systems because of their high latent heat of fusion. However, these same salts have poor thermal conductivities which inhibit the transfer of heat into the solid phase and out of the liquid phase. One concept for improving the thermal conductivity of the thermal energy storage system is to add a conductive filler material to the molten salt. High thermal conductivity pitch-based graphite fibers are being considered for this application. Although there is some information available on the thermal conductivity of lithium fluoride solid, there is very little information on lithium fluoride liquid, and no information on molten salt graphite fiber composites. This paper describes a hot filament technique for determining the thermal conductivity of molten salts. The hot filament technique was used to find the thermal conductivity of molten lithium fluoride at 930 C, and the thermal conductivity values ranged from 1.2 to 1.6 W/mK. These values are comparable to the slightly larger value of 5.0 W/mK for lithium fluoride solid. In addition, two molten salt graphite fiber composites were characterized with the hot filament technique and these results are also presented.

Jaworske, Donald A.↗

Automated eddy current analysis of materials

This research effort focused on the use of eddy current techniques for characterizing flaws in graphite-based filament-wound cylindrical structures. A major emphasis was on incorporating artificial intelligence techniques into the signal analysis portion of the inspection process. Developing an eddy current scanning system using a commercial robot for inspecting graphite structures (and others) has been a goal in the overall concept and is essential for the final implementation for expert system interpretation. Manual scans, as performed in the preliminary work here, do not provide sufficiently reproducible eddy current signatures to be easily built into a real time expert system. The expert systems approach to eddy current signal analysis requires that a suitable knowledge base exist in which correct decisions as to the nature of the flaw can be performed. In eddy current or any other expert systems used to analyze signals in real time in a production environment, it is important to simplify computational procedures as much as possible. For that reason, we have chosen to use the measured resistance and reactance values for the preliminary aspects of this work. A simple computation, such as phase angle of the signal, is certainly within the real time processing capability of the computer system. In the work described here, there is a balance between physical measurements and finite element calculations of those measurements. The goal is to evolve into the most cost effective procedures for maintaining the correctness of the knowledge base.

Workman, Gary L.↗

Automated eddy current analysis of materials

The use of eddy current techniques for characterizing flaws in graphite-based filament-wound cylindrical structures is described. A major emphasis was also placed upon incorporating artificial intelligence techniques into the signal analysis portion of the inspection process. Developing an eddy current scanning system using a commercial robot for inspecting graphite structures (and others) was a goal in the overall concept and is essential for the final implementation for the expert systems interpretation. Manual scans, as performed in the preliminary work here, do not provide sufficiently reproducible eddy current signatures to be easily built into a real time expert system. The expert systems approach to eddy current signal analysis requires that a suitable knowledge base exist in which correct decisions as to the nature of a flaw can be performed. A robotic workcell using eddy current transducers for the inspection of carbon filament materials with improved sensitivity was developed. Improved coupling efficiencies achieved with the E-probes and horseshoe probes are exceptional for graphite fibers. The eddy current supervisory system and expert system was partially developed on a MacIvory system. Continued utilization of finite element models for predetermining eddy current signals was shown to be useful in this work, both for understanding how electromagnetic fields interact with graphite fibers, and also for use in determining how to develop the knowledge base. Sufficient data was taken to indicate that the E-probe and the horseshoe probe can be useful eddy current transducers for inspecting graphite fiber components. The lacking component at this time is a large enough probe to have sensitivity in both the far and near field of a thick graphite epoxy component.

Workman, Gary L.↗

Effects of High-Temperature Irradiation on the Microstructure of Nuclear Graphite

This report summarizes the nondestructive microstructure characterization undertaken at Oak Ridge National Laboratory (ORNL) to understand the effects of high-temperature neutron irradiation on the structure of nuclear graphite. Nuclear graphite specimens were irradiated in the ORNL High Flux Isotope Reactor (HFIR) in the High Temperature Vehicle (HTV) with target irradiation temperatures of 900ºC, 1200ºC, and 1500ºC [1, 2]. The experiment was irradiated in the HFIR flux trap for two irradiation cycles, providing the specimens in the highest-fluence positions a total exposure of 4.5×10 21 n/cm 2 [E>0.1 MeV], equivalent to radiation damage of ~3.3 dpa (displacements per atom) according to the conversion factor in Burchell [3].

36 MATERIALS SCIENCE↗

Temperature-dependent tensile and shear response of P100/6061 graphite-aluminum

This paper summarizes the results of an investigation conducted to characterize tensile and shear response of P100/6061 graphite-aluminum composite in the temperature range -101 to 260 C. The off-axis tension test and Iosipescu shear test methods were employed to meet this objective. The experimental results indicate that both the fiber-dominated and matrix-dominated elastic properties exhibit relatively small changes in the considered temperature range. The effect of temperature on yielding and strength, however, is significant under longitudinal and shear loading. Residual stresses play a significant role in controlling the variation of the yield stress with temperature. The observed low transverse strength of the composite is explained by interfacial defects between adjacent precursor wires induced during fabrication.

Fujita, Takahiro↗

Characterization of thermally heat-treated polyacrylonitrile carbon fibers

This study investigates the graphitization process of polyacrylonitrile (PAN) carbon fibers by subjecting commercial fibers to thermal heat treatment at temperatures ranging from 1400 to 2100 °C in 100 °C increments, using either argon or nitrogen gas atmospheres. Changes in crystallinity, surface morphology, and lattice parameters were analyzed for two commercial carbon fibers using X-ray diffraction, scanning electron microscopy, and Raman spectroscopy. Results indicated minimal changes in surface morphology with increasing heat-treatment temperature; however, crystallinity significantly increased. Crystallinity changes were more strongly dependent on temperature rather than gas atmosphere or fiber type. At intermediate heat-treatment temperatures (1600–1800 °C), fibers treated in argon showed a slight preference for graphitization. The highest level of graphitization was measured at 2100 °C. Crystallite size increased as the intensity ratio of the D1 to G Raman peaks increased, reaching a peak around ~1800 °C, after which the ratio started to decrease. This behavior aligns with Ferrari's three-stage model of carbon crystallization and is consistent with both the Marie-Mering degree of graphitization and Brubaker's Integrated Absolute Differential models, all of which describe the transformation from an amorphous to a more graphitic structure. At the higher heat-treatment temperatures, the changes between atmospheres and fiber types were measured to converge to similar levels of graphitization. In conclusion, this study evaluates the progressive change in commercial grade carbon fibers when heat-treated.

Characterization↗