Search NASA⌕ Search

SEARCH · Search NASA

Results for “Heating Load”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Design and Analysis of an Advanced Three-Point Bend Test Approach for Miniature Irradiated Disk Specimens

Candidate tungsten armor materials in a magnetic confinement fusion device must be able to withstand thermal variation that leads to internal stresses caused by the impinging heat load. In addition, the thermomechanical properties of these materials are degraded by irradiation-induced defect accumulation. Fission reactor–based irradiation data are used to predict the fusion neutron damage and property change. This study examines the motivation and design of a custom-designed three-point bend test for neutron-irradiated disk specimens that are 3 mm in diameter to be able to define the flexural strength of advanced tungsten materials, alloys, and composites—and to the extent that embrittlement occurs after neutron irradiation. The theory provided shows a calculation for the flexural deflection and shear deflection due to the small-geometry constraints. A finite element deformation analysis is performed to evaluate the mechanical stress field of disk bend specimens. The stress values above 80% of the maximum stress are concentrated in 2.4 mm of the 3.0-mm length of the centerline across the tungsten disk diameter. A bend test fixture has been designed and fabricated to enable testing of these specimens with precisely engineered tolerance and minimal machine compliance. This fixture will be able to be placed inside a universal testing frame at elevated temperatures for the mechanical property evaluation of future neutron-irradiated disk specimens.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Design and Engineering of LUPIN: A Test-Bed Radio-Frequency Ion Source for Enhanced Neutral Beam Injection on DIII-D

The Large, Uniform Plasma for Ionizing Neutrals (LUPIN) is a radio-frequency (RF) inductively coupled plasma (ICP) chamber for demonstrating plasma performance of an RF ICP positive ion source upgrade for the DIII-D neutral beam injection (NBI) system. LUPIN will be used to investigate ion source physics, including neutral gas dynamics, plasma density uniformity, interactions with Faraday shields, and power coupling to novel RF antenna designs. LUPIN has an RF generator capable of delivering 20 kW of power at 2 MHz, which is coupled into a cylindrical quartz vessel measuring 20 cm in length and 10 cm in radius. This configuration matches the power density requirements for a full-scale ion source. Target hydrogen and deuterium plasma densities exceeding 10 18 m -3 would relate to extracted ion current densities of 2100 A/m 2 for 10s. Vacuum conductance and gas flow calculations predict a maximum achievable neutral gas flow rate of 1675 Pa ⋅ L/s at 5 Pa of He, which mimics the gas flow of the DIII-D NBI system. Designs have been developed for an internal Faraday shield to mitigate heat flux and ion sputtering on the dielectric vessel. Thermomechanical finite element simulations demonstrated the Faraday shield design to be capable of withstanding anticipated heat loads from worst-case operation scenarios. Finally, results of upcoming experimental investigations on LUPIN will guide the design of a full-scale prototype for DIII-D integration.

Faraday shield↗
DOE OSTI2023

Rooftop unit comparison calculator: a framework for comparing performance of rooftop units with building energy simulation

The applications of building energy simulation (BES) in designing heating, ventilation, and air conditioning (HVAC) systems are limited by the high costs of developing simulation models and the lack of references for determining the model parameters. This paper presents a software framework for selecting designs for rooftop unit HVAC (RTU) systems with BES. Specifically, this framework reduces the cost of using BES by automating the generation of EnergyPlus models. It also employs a systematic method for determining model parameters based on well-accepted datasets. We applied this framework in a comprehensive assessment of an advanced design of RTU systems in which 478 EnergyPlus models were developed without human involvement. The assessment reveals that replacing a constant-speed fan/coil with a multiple-speed fan/coil may not guarantee better overall performance. In conclusion, it also suggests the benefits of replacing furnace coils with heat pumps are subject to utility cost, weather conditions, and heating load profiles.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2021

The achievement of the T e,div feedback control by CD 4 seeding on EAST

A multi-function divertor feedback control system has been built on Experimental Advanced Superconducting Tokamak (EAST) to treat the divertor heat load issue. With the real-time data of the Langmuir probes and the impurity seeding, the divertor electron temperature (T e,div ) is well controlled to achieve the partial detachment phase. The first trial of the CD 4 seeding for the T e,div reduction has been achieved on EAST long-pulse discharge. In the seeding phase, the T e,div was maintained close to 5 eV, and the surface temperature of the target plate (T surface,div ) had a reduction of about 150° C. The plasma stored energy had a reduction in the control phase, so it is necessary to find a way to keep the good plasma confinement in the next step. The CD 4 injection also mitigated the low hybrid wave coupling rate in some degree. The big volume of the CD 4 injection lifted the Greenwald density fraction from ~0.4 to ~0.7, which made the SOL into high recycling state. As a result, most of the injected carbon particles were in the high ionized state, and with the lower of the T e,div , the tungsten line emission was suppressed obviously.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Ion temperature anisotropy in the tokamak scrape-off layer

Understanding tokamak exhaust-power heat loads on divertor plates depends critically on having a realistic model of the scrape-off layer (SOL) plasma. The Braginskii fluid model is often solved to understand the SOL plasma behavior. This model is based on the collisional limit for transport along the magnetic field B → . The ions and electron gyrofrequencies are assumed to be much larger than the Coulomb collision frequencies, which are nonetheless, sufficiently large to yield common parallel and perpendicular temperatures for each species, i.e. the temperatures are assumed to be isotropic. Additionally, in certain circumstances such as encountered for the tokamak H-mode, the ion temperature can be quite anisotropic. In this work, the anisotropy effects are implemented in the two-dimensional (2D) transport code UEDGE. Various geometries (1D slab, 2D slab and a toroidal tokamak geometry) are used to study the 2D structure of ion temperature anisotropy and its effects on plasma transport in detail. Results show that the effects of ion temperature anisotropy on the plasma parallel transport are substantial near the magnetic X-point, which leads to different steady state density profiles in the divertor regions. The extra mirror force introduced by ion temperature anisotropy can be one of the main forces contributing to the plasma flow in the SOL.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Physics of runaway electrons with shattered pellet injection at JET

Runaway electrons (REs) created during tokamak disruptions pose a threat to the reliable operation of future larger machines. Experiments using shattered pellet injection (SPI) have been carried out at the JET tokamak to investigate ways to prevent their generation or suppress them if avoidance is not sufficient. Avoidance is possible if the SPI contains a sufficiently low fraction of high-Z material, or if it is fired early in advance of a disruption prone to runaway generation. These results are consistent with previous similar findings obtained with Massive Gas Injection. Suppression of an already accelerated beam is not efficient using High-Z material, but deuterium leads to harmless terminations without heat loads. This effect is due to the combination of a large magnetohydrodynamic instability scattering REs on a large area and the absence of runaway regeneration during the subsequent current collapse thanks to the flushing of high-Z impurities from the runaway companion plasma. This effect also works in situations where the runaway beam moves upwards and undergoes scraping-off on the wall.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Simulation of plasma transport in MPS-LD linear plasma device by using BOUT++

Here a linear plasma device (LPD) module based on the 2D transport module under the BOUT++ framework is developed in this paper to simulate plasma transport in the LPD. The LPD module includes three parts, i.e. magnetic field calculation, simulation mesh generation and plasma transport setup. The magnetic field is calculated with the circular current loop using the location and current information of each coil. The mesh generation code can produce a simulation mesh for LPD by employing the magnetic field. The plasma transport model is based on the reduced Braginskii equations, which consist of the continuity equation, momentum equation, and energy equation. The fluid neutral model is applied for neutral particle simulation. Deuterium (D) and helium (He) ions and atoms can be simulated by the model. The first attempt to simulate plasma transport in the new LPD, called multiple plasma simulation linear plasma device (MPS-LD), is presented using the developed model. The D plasma transport in the MPS-LD is simulated and benchmarked against the two-point model, showing the validation of the BOUT++ simulation. The effects of radial transport on the heat load to the target are studied, which illustrates the significant impact of the radial diffusivities $D_⟂$ and $\mathcal{X}_{⟂i,e}$ on the plasma. Moreover, the He impurity injection process during the discharge is studied with emphasis on plasma–impurity interactions. The simulation results show that He injection can reduce the plasma energy load to the target significantly, and the efficiency depends on the He source density and injection velocity. The present work provides an alternative and flexible simulation tool for plasma transport in LPDs.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Runaway electron-induced plasma facing component damagein tokamaks

This Roadmap article addresses the critical and multifaceted challenge of plasma facing component (PFC) damage caused by runaway electrons (REs) in tokamaks, a phenomenon that poses a significant threat to the viability and longevity of future fusion reactors such as ITER and DEMO. The dramatically increased RE production expected in future high-current tokamaks makes it very difficult to avoid or mitigate REs in such devices when a plasma discharge terminates abnormally. Preventing damage from the intense localised heat loads they can cause requires a holistic approach that considers plasma, REs and PFC damage. Despite decades of progress in understanding the physics of REs and the thermomechanical response of PFCs separately, their complex interplay remains poorly understood. This document aims to initiate a coordinated, interdisciplinary approach to bridge this gap by reviewing experimental evidence, advancing diagnostic capabilities, and improving modelling tools across different scales, dimensionalities, and fidelities. Key topics include RE beam formation and transport, damage mechanisms in both brittle and metallic PFCs, and observed effects in major facilities such as JET, DIII-D, WEST and EAST. The Roadmap emphasises the urgency of predictive, high-fidelity modelling validated against well-diagnosed controlled experiments, particularly in the light of recent changes in ITER’s wall material strategy and the growing importance of private sector fusion initiatives. Each section of the Roadmap article is written to provide a concise overview of one area of this multidisciplinary subject, with an assessment of the status, a look at current and future challenges, and a brief summary. The ultimate goal of this initiative is to guide future mitigation strategies and design resilient components that can withstand the intense localised loads imposed by REs, thus ensuring the safe and sustainable operation of the next generation of fusion power plants.

Ratynskaia, Svetlana [KTH Royal Inst. of Technolog↗
DOE OSTI2025

Ultra-low magnetization and hysteresis loss in APC Nb 3 Sn superconductors

For the accelerator magnets of the next hadron collider, reducing superconductor persistent-current magnetization is not only important for achieving the desired field quality, but also crucial for its sustainability because the magnetization loss is the major heat load to the magnet cold mass. For conventional Nb 3 Sn conductors this requires reduction of effective subelement size (D eff ). For the restacked-rod-process (RRP ® ) conductors a physical subelement size (D sub ) as small as 35 µm (corresponding to a D eff close to 45 µm) can be reached, but at a significant price in J c . Another way to reduce the magnetization is by introducing artificial pinning centers (APC) using the internal oxidation approach. APC conductors outperform conventional Nb 3 Sn wires in two aspects: 1) higher J c at high fields, and 2) much lower J c and magnetization at low fields (e.g. below 5 T). Here, in this work we explored the fabricability of APC wires with small D sub . A 180-stack APC wire was produced and drawn to 0.7- and 0.5 mm diameters with good quality, with D sub s of 34 and 24 µm (D eff s of 36 and 25 µm), respectively. For the 34 µm-D sub wire, its non-Cu J c is higher than that of an RRP ® wire used for the High-Luminosity Large Hadron Collider (HL-LHC) project above 13 T (e.g. 36% higher at 4.2 K, 18 T), while its non-Cu magnetization at 1 T, ΔM(1 T), is only 29% of the RRP ® wire. Its non-Cu hysteresis loss for a cycle between 1 and 14 T, Q h (1–14 T), is 37% of the RRP ® wire. For the 24 µm-D sub wire, its non-Cu J c surpasses the HL-LHC RRP ® wire above 17.5 T, while its ΔM(1 T) and Q h (1–14 T) are only 17% and 23% of the RRP® wire, respectively. Its non-Cu Q h (±3 T) even meets the specification of the International Thermonuclear Experimental Reactor project.

Xu, X [Fermi National Accelerator Laboratory (FNAL↗
DOE OSTI2020

A new mechanism for filament disconnection at the X-point: poloidal shear in radial E × B velocity

Plasma filaments generated by turbulence in the scrape-off layer are sometimes observed in experiments and simulations to disconnect from the target plate in the vicinity of the X-point, resulting in a ‘quiescent zone’ with reduced fluctuations, possibly affecting the fluctuating part of the divertor heat loads. This phenomena is usually explained by the flux tubes squeezing, induced by flux expansion, down to scales where collisions dominate. In this work, we consider an additional mechanism spontaneously arising at the X-point: the poloidal shear in radial E × B velocity. Through a simple model, tested against 3D global turbulence simulations, herein we quantify the effectiveness of this disconnection mechanism and identify ways to control it.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Divertor detachment in the pre-fusion power operation phase in ITER during application of resonant magnetic perturbations

Detachment of the divertor plasma during application of resonant magnetic perturbation (RMP) fields is evaluated for hydrogen H-mode plasma during the first pre-fusion power operation (PFPO-1) phase in ITER by 3D plasma boundary modelling with EMC3–EIRENE. Plasma response effects from a linearized, resistive, single fluid MHD model are discussed, which includes partial screening of the externally applied field—but also field amplification near the separatrix. Furthermore, this field amplification is found to play a pivotal role for the magnetic footprint on the divertor targets, but is sensitive to model parameters. Extensions of the footprint beyond the straight portions of the ITER vertical divertor targets, optimized for high stationary heat flux handling, may be possible depending on the level of toroidal rotation in the plasma. Exhaust from the bulk plasma is guided by the helical corrugations (lobes) of the perturbed separatrix, and this results in an upstream heat flux that is distributed over these lobes with lower peak values than in the typical radial heat flux profiles seen in the absence of magnetic perturbations. As a consequence, an earlier onset (with respect to the upstream density) of detachment is found in the traditional strike zone when RMPs are applied, but secondary, non-axisymmetric strike locations appear—and those remain attached at temperatures above 10 eV. Neon seeding can mitigate these non-axisymmetric heat loads, but this becomes less efficient for large magnetic footprints.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Disruptive neoclassical tearing mode seeding in DIII-D with implications for ITER

New studies identify the critical parameters and physics governing disruptive neoclassical tearing mode (NTM) onset. An m/n = 2/1 mode in DIII-D that begins to grow robustly after a seeding event (edge localized mode ELM or sawtooth precursor and crash) causes the mode rotation to drop close to the plasma's Er = 0 rest frame; this condition opens the stabilizing ion-polarization current 'gate' and destabilizes an otherwise marginally stable NTM. Our new experimental and theoretical insights and novel toroidal theory-based modeling are benchmarked and scalable to ITER and other future experiments. Here, the nominal ITER rotation at q = 2 is found to be stabilizing ('gate closed') except for MHD-induced transients that could 'open the gate'. Extrapolating from the DIII-D ITER baseline scenario (IBS) discharges, MHD transients are much more likely to destabilize problematic robustly growing 2/1 NTMs in ITER; this makes predictions of seeding and control of both ELMs and sawteeth imperative for more than just minimizing divertor pulsed-heat loading.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Tungsten–carbon surface evolution and erosion modeling for a small angle slot divertor in DIII-D

Abstract We modeled tungsten–carbon mixed surface evolution, sputtering erosion, and transport for the tungsten coated region of a small angle slot (SAS) divertor design for the DIII-D tokamak. This divertor concept aims to achieve a closed slot dissipative plasma to minimize heat load and surface erosion, and to study high- Z material performance. Our advanced simulations use coupled ITMC-DYN material mixing/response and 3D full kinetic REDEP/WBC erosion/redeposition code packages, with divertor plasma solution from the SOLPS-ITER package with 4 MW power input. The SAS design geometry and resulting in-slot plasma parameters cause significant differences in predicted sputter/transport from a conventional divertor. For 2% C/D incident plasma ratio, an equilibrium mixed C/W surface is attained at ∼30 s of discharge, from wall sputtered carbon transported to the 10 cm long tungsten divertor region. Tungsten remains exposed to the plasma, but the evolved surface composition varies with different C/D ratios. Tungsten is primarily sputtered from the mixed surface by impinging carbon ions in the +1 to +4 charge states, with some self-sputtering. Redeposition of sputtered tungsten to the divertor is significant, ∼80% along the higher plasma temperature attached plasma SAS entrance region, but this is less than the typically near-unity values for a conventional divertor. Plasma-incident carbon is highly backscattered (∼50%) from the mixed surface, with little redeposition (<10%); this helps maintain tungsten in the surface sputter zone. Carbon is mainly sputtered from the mixed surface by D + ions, also with low redeposition (∼10%–30%). Finally, the modeling shows non-zero but low sputtered tungsten current from the divertor to the core plasma direction. These results appear favorable for effective testing of a tungsten-containing SAS divertor in DIII-D, and extrapolation of mixed-material evolution/response findings to the analogous low- Z /high- Z , Be/W, ITER plasma facing system.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Impact of Soret effect on hydrogen and helium retention in PFC tungsten under ELM-like conditions

Abstract In our previous work, we have demonstrated using nonequilibrium molecular-dynamics simulations that the fluxes of helium and self-interstitial atoms in the presence of a thermal gradient in tungsten are directed opposite to the heat flux, indicating that species transport is governed by a Soret effect, namely, thermal-gradient-driven diffusion, characterized by a negative heat of transport that drives species transport uphill, i.e. from the cooler to the hot regions of the tungsten sample. In this work, the findings of our thermal and species transport analysis have been implemented in our cluster-dynamics code, Xolotl, which has been used to compute temperature and species profiles over spatiotemporal scales representative of plasma-facing component (PFC) tungsten under typical reactor operating conditions, including extreme heat loads at the plasma-facing surface characteristic of plasma instabilities that induce edge localized modes (ELMs). We demonstrate that the steady-state species profiles, when properly accounting for the Soret effect, vary significantly from those where temperature-gradient-driven transport is not accounted for and discuss the implications of such a Soret effect on the response to plasma exposure of plasma-facing tungsten. Although our cluster-dynamics simulations do not yet include self-clustering of helium or hydrogen blister formation, our simulation results show that the Soret effect substantially reduces helium and hydrogenic species retention inside PFC tungsten.

36 MATERIALS SCIENCE↗
DOE OSTI2023

The JET hybrid scenario in Deuterium, Tritium and Deuterium-Tritium

The JET hybrid scenario has been developed from low plasma current carbon wall discharges to the record-breaking Deuterium-Tritium plasmas obtained in 2021 with the ITER-like Be/W wall. The development started in pure Deuterium with refinement of the plasma current, and toroidal magnetic field choices and succeeded in solving the heat load challenges arising from 37 MW of injected power in the ITER like wall environment, keeping the radiation in the edge and core controlled, avoiding MHD instabilities and reaching high neutron rates. The Deuterium hybrid plasmas have been re-run in Tritium and methods have been found to keep the radiation controlled but not at high fusion performance probably due to time constraints. For the first time this scenario has been run in Deuterium-Tritium (50:50). These plasmas were re-optimised to have a radiation-stable H-mode entry phase, good impurity control through edge T i gradient screening and optimised performance with fusion power exceeding 10 MW for longer than three alpha particle slow down times, 8.3 MW averaged over 5 s and fusion energy of 45.8 MJ.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Experimental, numerical and analytical evaluation of j × B -thrust for fast-liquid-metal-flow divertor systems of nuclear fusion devices

Abstract Divertor systems of fusion devices are exposed to intense heat loads from plasmas, which degrade solid plasma-facing components. Fast liquid metal (LM) flow divertors may be more advantageous for this purpose but have risk of piling due to intense magnetohydrodynamic (MHD) drag. However, severe deceleration of the flow could be countered with the injection of currents that are transverse to external magnetic fields, allowing to thrust the flow with j × B (Lorentz) forces. Given that the injection of currents as an approach to propel LM-divertor flows has remained experimentally understudied, this article focuses on the evaluation of j × B -thrust and finding its drawbacks. j × B -thrust was experimentally tested with free-surface-LM flows, a vertical magnetic field and an externally applied current. Experiments were reviewed with a theoretical model, showing agreement in the trends of theory and experiments. Full 3D-MHD-free-surface-flow simulations were also performed with FreeMHD and confirmed the sensitivity to unstable flow behavior in LM systems when applying external currents. Furthermore, excessive power requirements are expected for the implementation of j × B -thrust at the reactor scale, making these systems inefficient for commercial devices. This paper evidences that the simple operation of a LM-flow divertor with j × B -thrust, without any of the instabilities caused from reactor plasmas or parasitic currents, already presents intrinsic challenges.

Magnetohydrodynamics↗
DOE OSTI2023

Robust stellarator optimization via flat mirror magnetic fields

Stellarator magnetic configurations need to be optimized in order to meet all the required properties of a fusion reactor. In this work, it is shown that a flat-mirror quasi-isodynamic (QI) configuration (i.e. a QI configuration with sufficiently small radial variation of the mirror term) can achieve small radial transport of energy and good confinement of bulk and fast ions even if it is not very close to perfect omnigeneity, and for a wide range of plasma scenarios, including low $β$ and small radial electric field. This opens the door to constructing better stellarator reactors. On the one hand, they would be easier to design, as they would be robust against error fields. On the other hand, they would be easier to operate since, both during startup and steady-state operation, they would require less auxiliary power, and the heat loads on plasma-facing components caused by fast ion losses would be reduced to acceptable levels.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

The effect of plasma shaping on high density H-mode SOL profiles and fluctuations in TCV

Abstract The impact of plasma shaping on the properties of high density H-mode scrape-off layer (SOL) profiles and transport at the outer midplane has been investigated on Tokamakà configuration variable. The experimental dataset has been acquired by evolving the upper triangularity while keeping the other parameters constant. The scan comprises δ u p values between 0.0 and 0.6, excluding negative triangularity scenarios. Within this study, a transition from type-I edge localised modes to the quasi-continuous exhaust regime takes place from low to high δ u p . The modification of the upstream SOL profiles has been assessed, in terms of separatrix quantities, within the α t turbulence control parameter theoretical framework (Eich et al 2020 Nucl. Fusion 60 056016). The target parallel heat load and the upstream near-SOL density profiles have been shown to broaden significantly for increasing α t . Correspondingly, in the far SOL a density shoulder formation is observed when moving from low to high δ u p . These behaviours have been correlated with an enhancement of the SOL fluctuation level, as registered by wall-mounted Langmuir probes as well as the thermal helium beam diagnostic. Specifically, both the background and the filamentary-induced fluctuating parts of the first wall ion saturation current signal are larger at higher δ u p , with filaments being ejected more frequently into the SOL. Comparison of two pulses at the extremes of the δ u p scan range, but with otherwise same input parameters, shows that the midplane neutral pressure does not change much during the H-mode phase of the discharge. This indicates that indirect effects of the change in geometry, linked to first wall recycling sources, should not play a significant role. The total core radiation increases at high δ u p , on account of a stronger plasma–wall interaction and resulting larger carbon impurity intake from the first wall. This is likely associated to the enhanced first wall fluctuations, as well as a smaller outer gap and the close-to-double-null magnetic topology at high shaping.

Stagni, A. (ORCID:0000000180841544)↗