Search NASA⌕ Search

SEARCH · Search NASA

Results for “High Strain Composites”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Temperature-Dependent Sn Incorporation and Defect Formation in Pseudomorphic SiSn Layers on Si (001) via Molecular Beam Epitaxy

SiSn alloys have attracted growing interest for group-IV bandgap engineering, although their epitaxial growth remains challenging due to the extremely low equilibrium solubility of Sn in Si. In this work, fully strained (pseudomorphic) SiSn epitaxial layers were grown on Si (001) substrates by means of molecular beam epitaxy. A systematic investigation reveals a strong inverse correlation between growth temperature and Sn incorporation efficiency. Despite a constant Sn flux, the incorporated Sn composition decreases from 5.5% to 3.2% as the growth temperature increases, indicating a pronounced temperature dependence of Sn incorporation. Reflection high-energy electron diffraction indicates a gradual transition of the growth from two-dimensional to three-dimensional with increasing film thickness. Structural characterization by means of X-ray diffraction, atomic force microscopy, and transmission electron microscopy confirms the pseudomorphic growth and smooth surface morphology and reveals twins and stacking faults near the surface region. These results establish a quantitative reference for SiSn growth kinetics and provide guidance for future studies of SiSn and SiGeSn alloys in silicon-compatible electronic and optoelectronic applications.

SiSn alloys↗
DOE OSTI2023

Tailoring Growth Interfaces of Virtual Substrates for Power Electronics

Power electronics materials are poised to play a critical role in fulfilling next generation energy needs, with up to 90% of future energy demand predicted to flow through power electronics at some point.[1] Among a number of candidate materials, AlxGa1-xN is the strongest, having bipolar dopability, thermal and chemical stability, an ultra-wide bandgap, and demonstrated experimental feasibility. However, AlGaN growth is limited by a lack of lattice-matched substrates, ultimately stunting material quality at higher thicknesses needed for power electronics applications. Further, high power applications increasingly call for fully vertical device structures, necessitating a conductive substrate. [1] Recently our group identified the (111) plane of TaC as a conductive surface lattice-matched to Al0.55Ga0.45N, taking inspiration from prior work of AlN and GaN binaries on carbide and boride substrates. [2,3,4] In this talk we demonstrate the growth of (111)-oriented TaC by RF sputtering. We investigate the interface of TaC with sapphire and SiC substrates and identify means to suppress competing Ta2C nucleation in order to stabilize (111)-oriented TaC. Potential stacking sequences are identified with respect to crystal structure and observed twinning in the TaC films. We next assess structural changes and film recrystallization that results from face-to-face annealing of TaC thin films at high temperatures above 1500 degrees Celsius. Changes to grain structure and domain size are assessed by x-ray diffraction and surface morphology is explored using atomic force microscopy. Figure 1 shows significant improvements to in- and out-of-plane strain following annealing along with the formation of terraced step edges at the film surface. Strain as a function of material composition and thickness is considered, as this may play a major role in future nucleation of AlGaN layers.

CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND SU↗
DOE OSTI2024

Tailoring Growth Interfaces of Virtual Substrates for Power Electronics

Power electronics materials are poised to play a critical role in fulfilling next generation energy needs, with up to 90% of future energy demand predicted to flow through power electronics at some point. AlxGa1-xN ranks high among candidate materials, having bipolar dopability, thermal and chemical stability and an ultra-wide bandgap. However, AlGaN growth is limited by a lack of lattice-matched substrates, ultimately stunting material quality at higher thicknesses needed for power electronics applications. Further, high power applications increasingly call for fully vertical device structures, necessitating a conductive substrate. Recently our group identified the (111) plane of TaC as a conductive surface lattice-matched to Al0.55Ga0.45N, taking inspiration from prior work of AlN and GaN binaries on carbide and boride substrates. In this talk we demonstrate the growth of (111)-oriented TaC by RF sputtering. We investigate the interface of TaC with sapphire and SiC substrates and identify means to suppress competing Ta2C nucleation in order to stabilize (111)-oriented TaC. Potential stacking sequences are identified with respect to crystal structure and observed twinning in the TaC films. We next assess structural changes and film recrystallization that results from face-to-face annealing of TaC thin films at high temperatures above 1500 degrees C. Changes to grain structure and domain size are assessed by x-ray diffraction and surface morphology is explored using atomic force microscopy. Figure 1 shows significant improvements to in- and out-of-plane strain following annealing along with the formation of terraced step edges at the film surface. Strain as a function of material composition and thickness is considered, as this may play a major role in future nucleation of AlGaN layers. (1) R. J. in a face-to-face configuration, as illustrated in the schematic at left. Kaplar et al 2017, ECS J. Solid State Sci. Technol. 6 Q3061; (2) D. M. Roberts et al 2022, https://arxiv.org/abs/2208.11769; (3) T. Aizawa et al 2008, J Crys Growth 310, 1 22; (4) R. Liu et al 2002, Appl. Phys. Lett. 81, 3182-3184.

ENGINEERING↗
DOE OSTI2024

Elucidating the role of Cr migration in Ni-Cr exposed to molten FLiNaK via multiscale characterization

Structural materials used in nuclear reactor environments are subjected to coupled extremes such as high temperature, irradiation, and corrosion which act in concert to degrade their functional performance. Connecting alloy microstructure such as grain boundaries, and accumulating point defects with corrosion attack and pore morphology is critical to understanding underlying mechanisms. We uncover the compositional variations and morphology at multiple length scales in corrosion-damaged Ni-Cr alloy after exposure to oxidants in molten fluoride salts. A complex network of dense corrosion pores is detected by surface-level SEM observations. The corrosion pores take on a 1-dimensional morphology and are enriched with Ni and depleted of Cr 1–5 µm from the pore surface. STEM-EDS and 4D-STEM strain maps acquired simultaneously highlight the local variations in composition and structure of a ≤ 200 nm Cr-rich layer identified from a cross-section taken at the bottom of an isolated corrosion pore between the Ni-Cr alloy matrix and the embedded salt. However, the absence of an observed interface between the Ni-Cr alloy matrix and the FCC-structured Cr-rich layer suggests that Cr plating from the salt did not transpire. These findings support a proposed Cr lattice diffusion mechanism rather than Cr-precipitation from the salt to accommodate temperature transient conditions during sample cooling. Through the development of a 1D phase field model, these results are rationalized by formation energies for the Ni- and Cr-oxidation into the molten salt. This study reveals the locally altered microstructure caused by high temperature corrosion in non-steady-state molten salt nuclear reactor environments.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Multiscale investigation of thermomechanical and compositional developments in Ni alloy 718 under laser processing

Laser processing has been widely employed in various applications due to its exceptional spatial resolution. However, the rapid temperature gradients generated in localized areas present significant challenges for experimental characterization using conventional instruments. To characterize Ni alloy 718 during laser processing, we employed in-situ synchrotron X-ray diffraction with a high-speed detector, a method particularly well-suited for probing processes with high temporal and spatial resolution. Through a series of in-situ experiments, we investigated the local variations in the evolution of microstructures and thermomechanical behaviors within a keyhole mode melt pool. The in situ macroscopic thermomechanical behaviors were quantified using an empirical model derived from diffraction patterns, with experimental results showing reasonable agreement with finite element analysis. Various laser parameters were tested to assess their influences on the residual strains in the melt pools. The results revealed that the residual strain in the keyhole mode melt pool is relatively insensitive to variations in the parameters and is smaller than that in the melt pool created under conduction mode laser scanning. Additionally, we analyzed the shapes of individual diffraction spots, providing insights into the plastic behaviors and compositional developments in the resolidified alloy. The analysis confirmed that compositional variations in a dendritic microstructure manifest as asymmetric broadening of the diffraction spots.

Ni alloy 718↗
DOE OSTI2020

Effect of heat treatment on the tensile behavior of selective laser melted Ti-6Al-4V by in situ X-ray characterization

Selective Laser Melted Ti-6Al-4V (as-SLMed) exhibits decreased yield strength, increased work hardening, and increased ductility after heat treatment at 730 degrees C (HT-730) or 900 degrees C (HT-900) for 2 h. To understand the change of mechanical properties, in situ high energy X-ray diffraction (HEXRD) is used to examine the phase composition, load partitioning, slip system activity, and dislocation density evolution in all three specimens. The as-SLMed specimen is dominated by martensitic α'. After heat treatment, α' partly or fully decomposes into α+β, reducing the yield strength. In HT-730, beta precipitates with confined size show much higher lattice strain than the α'/α matrix during deformation; in HT-900, the lattice strain difference is mostly eliminated. This is a key reason for the increased ductility in HT-900. From the anisotropic lattice strain development, basal slip is identified as the easiest slip system in α'/α. Using an elasto-plastic self-consistent (EPSC) model, the critical resolved shear stress ratio between prismatic slip and basal slip (CRSS prism /CRSS basal ) is estimated to be 1.31 and 1.16 in the as -SLMed and the HT-900 specimens, respectively. Further, the alpha phase in HT-900 is able to activate multiple slip systems and accumulate more dislocations during plastic deformation. This explains why HT-900 has better ductility and higher work hardening rate than the other two specimens.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Composition dependence of atomic order in strain-relaxed, metastable GeSn alloys

Extended x-ray absorption fine structure (EXAFS) measurements of single-crystal Ge/GeSn radial heterostructure nanowires are used to examine the effects of composition on both short-range order (SRO) and longer-range disorder in GeSn alloys. GeSn has prompted significant interest because it can achieve a direct band gap for sufficient Sn concentrations beyond the equilibrium solid solubility limit in an all-group IV system. Short-range order in this material is particularly interesting as it has been predicted to affect the band gap independent of average composition or strain effects. By independently controlling the Sn composition and GeSn thickness during chemical vapor deposition of misfitting GeSn shells around ultrathin, elastically compliant, Ge core nanowires, the elastic misfit strain in the GeSn is minimized for Sn compositions over the studied range ≈Ge 0.96 Sn 0.04 to Ge 0.88 Sn 0.12 . The degree of SRO was found to decrease with increasing Sn composition. Additionally, damping of the EXAFS signal was observed as the Sn content increased, particularly for increasingly distant atomic shells about the absorbing atom, even for scattering paths not involving Sn atoms. This result is quantified as an increase in the mean-squared relative displacement parameters of the shells. These measurements reveal the accommodation of local strain due to the presence of the highly size-mismatched Sn atoms in the Ge diamond cubic lattice (≈14%), which may have effects on the band structure of the material in addition to the influence of short-range atomic order. Comparison among the nanowire samples allows for calculation of the topological rigidity parameter, a ∗∗ , for the first-neighbor bond lengths. Furthermore, these exhibit chemically distinct values for Ge-Ge, Ge-Sn, and Sn-Sn, and they are consistent with the value a ∗∗ = 0.75 ± 0.07 confirming the general applicability of the model to alloys with both large amounts of natural misfit strain and the potential for short-range order.

Crystal structure Semiconductors Transmission elec↗
DOE OSTI2024

Multi-stage load partitioning in additively manufactured Al6061+TiC nanocomposite characterized by in-situ neutron diffraction

Metal matrix composites (MMCs), combining metal matrix and ceramic particles, exhibit high mechanical strength and stiffness compared to conventional metallic materials. During fusion-based additive manufacturing (AM), MMCs undergo a rapid heating and cooling thermal history, which affects the interfacial bonding, thermal misfit stress and mechanical load transfer behavior between the metal matrix and particles, thus impacting the bulk mechanical performance. Here, we investigate the deformation dynamics and phase-specific load transfer in fusion-based AMed Al6061 +TiC MMCs through in-situ neutron diffraction. By calculating the phase-specific lattice strains, a multi-stage load transfer and deformation behavior during uniaxial compression is revealed: (1) elastic deformation in Stage I for both phases; (2) sudden stress rebalance between two phases in Stage II, evidenced by a sudden decrease in Al lattice strain and increase in TiC; (3) active load carrying by both phases in Stage III, with both phases experiencing an increase in lattice strains. Further, the deformation mechanism of each stage is deducted by correlating the evolutions of the interphase stresses and peaks’ broadening and intensity of the Al matrix. The local plastic deformation of the Al matrix near the phase interface is triggered and leads to stress rebalancing in Stage II. The global plastic deformation subsequently propagates throughout the Al matrix in Stage III, and the composite is further hardened through both dislocation multiplication and load transfer. The findings offer valuable insights into deformation and load-sharing behavior in AMed MMCs.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Bio-treatment of poplar via amino acid for interface control in biocomposites

Advanced biocomposites reinforced by abundant biomass-derived fillers can add a revenue stream to enhance the economic viability of biofuel production chains and the energy efficiency of the composite industry. However, the low stiffness of biopolymers limits their use in structural applications. Poplar fibers (mesh size: <180 μm, Populus spp.), an abundant waste from the wood industry, were used as bio-filler to fabricate high-performance biocomposites based on polylactic acid (PLA), in which the poplar fibers were modified by an amino acid (l-lysine). As a benefit of the amino acid treatment, the tensile Young's moduli of the lysine/poplar/PLA composites increased by up to 68% with the addition of a small amount of lysine, compared with neat PLA. At the same time, the tensile strength, failure strain, and Young's modulus of the poplar/PLA composites all increased after adding only 0.1 wt % of lysine. It has been observed that the lysine content has a significant effect on the decomposition temperature, complex viscosity, storage modulus, crystallization temperature, and crystallinity of composites. The fracture surfaces of the composites with an optimum lysine content had fewer voids and were more compact compared with composites without any lysine. The pores on the surfaces of poplar fibers became more available for the penetration of PLA molecules as a result of lysine addition. Finally, this study presents a facile method for reinforcing biocomposites with extremely low-cost and environmentally friendly biofillers.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

Storing Co 2 in Built Infrastructure: Co 2 Carbonation of Precast Concrete Products

The overall objective of the proposed study was to advance the technical understanding of CO 2 incorporation into novel cementitious materials for the development of high value products that provide a net reduction in carbon emissions. This project combined two primary phases of research that addressed technical barriers related to (i) optimizing CO 2 storage capability of cementitious materials, (ii) evaluating and enhancing physical properties of novel carbonated materials, and (iii) assessing the reductions in life cycle CO 2 emissions attributed to CO 2 carbonation of precast cementitious materials. Engineered cementitious composites (ECC) are a class of highly ductile concrete composites that have been shown to be very durable when used in the built environment. CO 2 carbonation of ECC was examined in this study and it was found that precast ECC specimens could sequester up to 35% CO 2 by cement mass after 24 hours of curing at a CO 2 pressure of 0.5 MPa and 23°C and had a strain capacity of 3%. Carbonation conditions were optimized at the bench-scale and then utilized to create full-scale CO 2 -cured ECC railroad ties that were field tested on a train track. Rail ties were selected for this initial assessment of CO 2 storage in precast concrete materials due to the large market for concrete ties in the railroad industry. Although the full-scale rail ties passed all of the required American Railway Engineering and Maintenance-of-Way Association qualifying mechanical tests, on-track testing of the CO 2 -cured ECC rail ties was unsuccessful due to fiber alignment in the ECC the during the rail tie casting process which prevented the material from achieving the expected level of strain capacity. This result highlights the challenge in scaling up bench-scale processes to full-scale product manufacturing and requires additional investigation into the casting process of large-scale infrastructure elements using ECC combined with carbonation curing. Life cycle assessment of a CO 2 -cured ECC rail tie versus a traditional concrete rail tie indicates that the ECC tie can have lifecycle carbon savings of between 11% and 51% depending on how much longer its useful lifetime is compared to traditional concrete rail ties. Both carbon and cost savings are driven by a reduction in the need to replace broken rail ties, so the key factor is the extent to which a CO 2 -cured ECC rail tie will have increased lifetime durability compared to alternative rail ties.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2025

Polypropylene Composites Reinforced With Recycled Waste Cellulosic Fiber/Fine Mixture: The Impact of Cellulose Sieving on Performance

This study explores how a sieving step of waste cellulosic fiber and fine (WCFF) mixture affects the performance of WCFF‐loaded polypropylene (PP) composites and whether the separation of fines from fibers offers an added benefit. The WCFF samples were downsized, and four different filler size ranges were sieved using a series of mesh sizes from 4 to 0.85 mm. The WCFF/PP composites were then compounded at 20 wt.% loading of WCFF using a twin‐screw extruder. Incorporating WCFF increased the tensile strength to 41.28 MPa and the modulus to 3207 MPa, accounting for 28% and 38% enhancements, respectively. Interestingly, the greatest improvements were associated with the nonsieved WCFF case, and the sieved WCFF fibers provided only marginal enhancements over virgin PP. The outperformance of nonsieved WCFF was attributed to the synergistic reinforcement of hybrid fibers and fines as well as the maintenance of longer fibers in the system. However, the strain at break and impact strength of PP decreased after introducing WCFF. Moreover, the complex viscosity and storage modulus increased with an increase in the filler size, due to the formation of a more effective percolative network. The PP's crystallinity exhibited a relatively strong dependency on the sieving, where WCFF samples with short‐aspect‐ratio fillers promoted the crystallinity significantly. It was also found that the WCFF degradation onset temperature increased once it was incorporated into PP. This study suggests that waste cellulosic feedstocks can be utilized as a reinforcement without additional sieving to manufacture high‐performance and cost‐effective composites.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Role of geometric dynamic recrystallization in nanocrystalline alloys

Nanocrystalline and near-nano-grained metals are plagued with an overall lack of ductility and formability. This is in part due to their inability to support the dislocation mechanisms or undergo the same types of transformations that conventional coarse-grained metals access in order to increase their workability. Therefore, despite their advanced properties such as high strength, the manufacturing of such fine-grained metals, which exposes them to multi-axial states of stress in operations such as rolling, drawing, extrusion, forging, and bending, has not been possible. In this work, we address this limitation and highlight an important aspect of geometric dynamic recrystallization (GDRX) in nanocrystalline materials as a way to improve manufacturability. In particular, using two different alloy compositions and two different processing techniques, this study points to the fact that if nanocrystalline or near nano metals can be truly stabilized, they can repeatedly undergo the same types of processes that conventional coarse-grained metals endure, increasing both their formability and hence manufacturability. The results reveal that due to a large number of initial high-angle grain boundaries and large applied compressive strains, GDRX is activated in the absence of any discontinuous dynamic recrystallization (DDRX) or continuous dynamic recrystallization (CDRX). This is a unique aspect of stabilized nanocrystalline materials, as traditionally fine-grained metals are not microstructurally stable enough to accommodate such an event.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Generation of a highly attenuated strain of Pseudomonas aeruginosa for commercial production of alginate

Alginate is an important polysaccharide that is commonly used as a gelling agent in foods, cosmetics and healthcare products. Currently, all alginate used commercially is extracted from brown seaweed. However, with environmental changes such as increasing ocean temperature and the increasing number of biotechnological uses of alginates with specific properties, there is an emerging need for more reliable and customizable sources of alginate. An alternative to seaweed for alginate production is Pseudomonas aeruginosa, a common Gram-negative bacterium that can form alginate containing biofilms. However, P. aeruginosa is an opportunistic pathogen that can cause life-threatening infections in immunocompromised patients. Therefore, we sought to engineer a non-pathogenic P. aeruginosa strain that is safe for commercial production of alginate. Using a homologous recombination strategy, we sequentially deleted five key pathogenicity genes from the P. aeruginosa chromosome, resulting in the marker-free strain PGN5. Intraperitoneal injection of mice with PGN5 resulted in 0% mortality, while injection with wild-type P. aeruginosa resulted in 95% mortality, providing evidence that the systemic virulence of PGN5 is highly attenuated. Importantly, PGN5 produces large amounts of alginate in response to overexpression of MucE, an activator of alginate biosynthesis. The alginate produced by PGN5 is structurally identical to alginate produced by wildtype P. aeruginosa, indicating that the alginate biosynthetic pathway remains functional in this modified strain. The genetic versatility of P. aeruginosa will allow us to further engineer PGN5 to produce alginates with specific chemical compositions and physical properties to meet different industrial and biomedical needs.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2019

Origin of High Activity and Durability of Twisty Nanowire Alloy Catalysts under Oxygen Reduction and Fuel Cell Operating Conditions

The ability to control the surface composition and morphology of alloy catalysts is critical for achieving high activity and durability of catalysts for oxygen reduction reaction (ORR) and fuel cells. Here, this report describes an efficient surfactant-free synthesis route for producing a twisty nanowire (TNW) shaped platinum–iron (PtFe) alloy catalyst (denoted as PtFe TNWs) with controllable bimetallic compositions. PtFe TNWs with an optimal initial composition of ~24% Pt are shown to exhibit the highest mass activity (3.4 A/mg Pt , ~20 times higher than that of commercial Pt catalyst) and the highest durability (<2% loss of activity after 40000 cycles and <30% loss after 120000 cycles) among all PtFe-based nanocatalysts under ORR or fuel cell operating conditions reported so far. Using ex situ and in situ synchrotron X-ray diffraction coupled with atomic pair distribution function (PDF) analysis and 3D modeling, the PtFe TNWs are shown to exhibit mixed face-centered cubic (fcc)-body-centered cubic (bcc) alloy structure and a significant lattice strain. A striking finding is that the activity strongly depends on the composition of the as-synthesized catalysts and this dependence remains unchanged despite the evolution of the composition of the different catalysts and their lattice constants under ORR or fuel cell operating conditions. Notably, dealloying under fuel cell operating condition starts at phase-segregated domain sites leading to a final fcc alloy structure with subtle differences in surface morphology. Due to a subsequent realloying and the morphology of TNWs, the surface lattice strain observed with the as-synthesized catalysts is largely preserved. This strain and the particular facets exhibited by the TNWs are believed to be responsible for the observed activity and durability enhancements. These findings provide new insights into the correlation between the structure, activity, and durability of nanoalloy catalysts and are expected to energize the ongoing effort to develop highly active and durable low-Pt-content nanowire catalysts by controlling their alloy structure and morphology.

25 ENERGY STORAGE↗
DOE OSTI2020

Meso-scale modeling and damage analysis of carbon/epoxy woven fabric composite under in-plane tension and compression loadings

The mechanical properties and damage behaviors of carbon/epoxy woven fabric composite under in-plane tension and compression are studied at the meso-scale level through experiment and simulation. An efficient representative volume element (RVE) modeling method with consistent mesh, high yarn volume fraction and realistic geometry is proposed. The material constitutive laws with plasticity, tension-compression asymmetry and damage evolution are established for the three components - yarn, matrix and interface, respectively. Significantly different mechanical properties and damage evolutions are observed depending on loading conditions and initial geometry characteristics. It shows a non-linear stress-strain curve with clear transition region and intensive damage in tension, while a quasi-linear behavior up to facture is observed in compression with little damage prior to final fracture. Furthermore, compared to the constant Poisson's ratio with straining in compression, a dramatic increase in Poisson's ratio appears in tension. Simulation shows damage mechanisms including transverse damage, matrix damage and delamination, which all play critical roles in the property evolution. In particular, the rapid damage accumulation after elastic deformation destroys the strong bonds and causes the easy deformation of transverse yarns which results in the transition region and large Poisson's ratio in tension. All the mechanical behaviors and damage evolutions are well captured and explained with the current RVE model.

42 ENGINEERING↗
DOE OSTI2022

Simple steps to enable reproducibility: culture conditions affecting Chlamydomonas growth and elemental composition

Even subtle modifications in growth conditions elicit acclimation responses affecting the molecular and elemental makeup of organisms, both in the laboratory and in natural habitats. Here, we systematically explored the effect of temperature, pH, nutrient availability, culture density, and access to CO 2 and O 2 in laboratory-grown algal cultures on growth rate, the ionome, and the ability to accumulate Fe. We found algal cells accumulate Fe in alkaline conditions, even more so when excess Fe is present, coinciding with a reduced growth rate. Using a combination of Fe-specific dyes, X-ray fluorescence microscopy, and NanoSIMS, we show that the alkaline-accumulated Fe was intracellularly sequestered into acidocalcisomes, which are localized towards the periphery of the cells. At high photon flux densities, Zn and Ca specifically over-accumulate, while Zn alone accumulates at low temperatures. The impact of aeration was probed by reducing shaking speeds and changing vessel fill levels; the former increased the Cu quota of cultures, the latter resulted in a reduction in P, Ca, and Mn at low fill levels. Trace element quotas were also affected in the stationary phase, where specifically Fe, Cu, and Zn accumulate. Cu accumulation here depends inversely on the Fe concentration of the medium. Individual laboratory strains accumulate Ca, P, and Cu to different levels. All together, we identified a set of specific changes to growth rate, elemental composition, and the capacity to store Fe in response to subtle differences in culturing conditions of Chlamydomonas, affecting experimental reproducibility. Accordingly, we recommend that these variables be recorded and reported as associated metadata.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2024

Steady-state fuel performance analyses for the preliminary fuel concept of general atomics fast modular reactor

Here this manuscript presents the fuel performance analysis results of the General Atomics Fast Modular Reactor (FMR) based on an axi-symmetric (2D-RZ) geometry. Three fuel performance model sets that fit the FMR fuel specifications best, i.e., a BISON baseline model set, a BISON diffusion enhancement model set, and a BISON-FASTGRASS model set, were identified and evaluated against a series of relevant experimental cases featuring high burnup and low irradiation temperature conditions. The three BISON-based model sets were then utilized to conduct a comprehensive fuel performance analysis of the FMR fuel under normal operation including the shutdown/restarting periods for refueling. The evaluation of the fuel performance parameters, represented by temperature, internal pressure, stress, and strain, shows that the FMR fuel maintains its thermal and mechanical integrity during normal operation. Technology gaps and limitations are also discussed to guide future efforts for extending the performance analysis to transient scenarios as well as improving the fuel performance evaluation through experiments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Silver-carbon-nanotube composite metallization for increased durability of silicon solar cells against cell cracks

One of the ways to reduce the cost of solar electricity is to reduce the degradation rate of solar modules and extend their lifetime well beyond 30 years. The extended module lifetime translates to increased bankability of utility-scale PV projects. In this work, we specifically address cell-crack-induced degradation by introducing crack-tolerant metallization. Herein, we make use of low-cost, multi-walled carbon nanotubes embedded in commercial screen-printable silver pastes as a highly integratable engineering solution. When the carbon nanotubes are appropriately functionalized and incorporated into commercial silver pastes, the resulting metal contacts on solar cells, after screen-printing and firing, show exceptional fracture toughness. These composite metal contacts possess increased ductility, electrical gap-bridging capability greater than 50 µm, and “self-healing” to regain electrical continuity even after cycles of complete electrical failure under large strain. While providing crack-tolerant mechanical properties, the composite paste delivers similar beginning-of-life cell performance as the conventional silver paste.

14 SOLAR ENERGY↗