Search NASA⌕ Search

SEARCH · Search NASA

Results for “Homogeneous flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

A statistical investigation of the single-point pdf of velocity and vorticity based on direct numerical simulations

Vorticity plays a fundamental role in turbulent flows. The dynamics of vorticity in turbulent flows and the effect on single-point closure models were investigated. The approach was to use direct numerical simulations of turbulent flows to investigate the pdf of velocity and vorticity. The preliminary study of homogeneous shear flow has shown that the expectation of the fluctuating pressure gradient, conditioned with a velocity component, is linear in the velocity component, and that the coefficient is independent of velocity and vorticity. In addition, the work shows that the expectation of the pressure gradient, conditioned with a vorticity component, is essentially zero.

Mortazavi, M.↗

Optical coronal emission lines from cooling flows in elliptical galaxies and galaxy clusters

Luminosities, surface brightnesses, and line profiles of the coronal lines predicted by standard models for cooling flows in clusters of galaxies and in individual early-type galaxies are presented. The coronal line luminosities of cooling flows depend primarily on the total rate at which gas is cooling. In homogeneous cooling flow models (HMs) in which all of the gas flows into the central regions, the coronal lines are very centrally concentrated, coming mainly from a limb-brightened shell lying just within the sonic radius of the inflow. For HMs, the central surface brightnesses of the stronger coronal lines from nearby clusters with large cooling rates are expected to be about 6 x 10 to the -17th ergs/sq cm/s/sq arcsec. For inhomogeneous models (IMs) in which gas cools out of the flow at large radii, the surface brightness profiles of the coronal lines are more extended, and the central surface brightness is much lower. The integrated line profiles of the HMs are very wide and flat and the central line profiles are double-peaked. The IMs have nearly Gaussian line profiles.

Sarazin, Craig L.↗

Interaction of large scale flow structures with gyrokinetic turbulence

Shear flows have a profound influence on turbulence-driven transport in tokamaks. The introduction of arbitrary initial flow profiles into the code ORB5 [Jolliet et al., Comput. Phys. Commun. 177, 409 (2007)] allows the convenient study of how flows on all length scales both influence transport levels and self-consistently evolve. A formulation is presented which preserves the canonical structure of the background particle distribution when either toroidal or poloidal flows are introduced. Turbulence suppression is possible above a certain shearing rate magnitude for homogeneous shear flows, and little evolution of the shearing rate is seen. However, when a flow with a zone boundary, where the shearing rate reverses at mid-radius, is introduced, the shear flow evolves substantially during the simulation. E x B shear flows with a zone boundary of a positive sign decay to a saturation amplitude, consistent with the well known saturation of turbulently generated zonal flows. Unlike the E x B flow, the parallel flows relax diffusively.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Suppressing the Skin-Core Structure of Injection-Molded Isotactic Polypropylene via Combination of an in situ Microfibrillar Network and an Interfacial Compatibilizer

Injection-molded semicrystalline polymer parts generally exhibited a so-called skin-core structure basically as a result of the large gradients of temperature, shear rate, stress, and pressure fields created by the boundary conditions of injection molding. Suppression of the skin-core structure is a long-term practical challenge. In the current work, the skin-core structure of the conventional injection-molded isotactic polypropylene (iPP) was largely relieved by the cooperative effects of an in situ microfibrillar network and interfacial compatibilizer. The in situ poly(ethylene terephthalate) microfibrils of 1-8 {micro}m in diameter and large aspect ratios of above 40 tended to entangle with each other to generate a microfibrillar network in the iPP melt. During injection molding, the iPP molecules experienced confined flow in the microchannels or pores formed by the microfibrillar network, which could redistribute and homogenize the flow field of polymer melt. Addition of the compatibilizer, glycidyl methacrylate-grafted iPP, restrained the molecular orientation but facilitated preservation of oriented molecules due to the chemical bonds at the interface between PET microfibrils and iPP. The cooperative effects of in situ microfibrillar network and interfacial compatibilizer led to almost the same molecular orientation across the whole thickness of the injection-molded parts. Additionally, the content of {beta} crystals in different layers of injection-molded iPP parts depended on the combined effects of the molecular orientation, the amount of oriented crystals, and the crystallization time between 105 and 140 C. The presence of the interfacial compatibilizer facilitated formation of the {beta} crystals because of preservation of the oriented molecules.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A Galilean Invariant Explicit Algebraic Reynolds Stress Model for Curved Flows

A Galilean invariant weak-equilbrium hypothesis that is sensitive to streamline curvature is proposed. The hypothesis leads to an algebraic Reynolds stress model for curved flows that is fully explicit and self-consistent. The model is tested in curved homogeneous shear flow: the agreement is excellent with Reynolds stress closure model and adequate with available experimental data.

Girimaji, Sharath↗

Particle Flow Distribution in a Fluidized-Particles Multitube Solar Receiver

A fluidized-particles two-tube solar receiver was tested at ambient temperature at PROMES Laboratory to investigate the influence of an inhomogeneous solar flux density on the particle mass flow rate between the tubes. The principle of this 3rd generation solar receiver is to fluidize the particles in a container, called dispenser, in which the tubes’ bottom are immersed. The fluidized particles are flowing upward the tubes by applying an overpressure in the dispenser. Air velocities are changed inside the tubes, thanks to air mass flow controllers, to represent temperature heterogeneity between the tubes. Air velocities from 0.05 up to 0.52 m/s were tested, both in homogeneous and heterogeneous conditions. In the heterogeneous ones, the differences in air velocity between the tubes aim to mimic a difference in temperature from 20 to 100 % with homogeneous air flow rates injected. The following conclusions were drawn. First, the particle mass flux in the tubes are the same with homogeneous air velocities, each one following a calibration map previously obtained. Second, different air velocities lead to different particle mass flux. Third, the rise of the total particle mass flux diminishes the pressure in the dispenser. Four, this diminution of pressure leads to a decrease of the particle mass flow rate of the tube with the lower air velocity. This influence can lead in some cases to the stop of the fluidized bed circulation in the affected tube.

Sahuquet, Guillaume (ORCID:0000000302752890)↗

Extensional Flow of a Polystyrene Boger Fluid Through a 4:1:4 Axisymmetric Contraction/Expansion

The creeping flow of a dilute (0.025 wt%) monodisperse polystyrene/polystyrene Boger fluid through a 4:1:4 axisymmetric contraction/expansion is experimentally observed for a wide range of Deborah numbers. Pressure drop measurements across the orifice plate show a large extra pressure drop that increases monotonically with Deborah number above the value observed for a similar Newtonian fluid at the same flow rate. This enhancement in the dimensionless pressure drop is not associated with the onset of a flow instability, yet it is not predicted by existing steady-state or transient numerical computations with simple dumbbell models. It is conjectured that this extra pressure drop is the result of an additional dissipative contribution to the polymeric stress arising from a stress-conformation hysteresis in the strong non-homogeneous extensional flow near the contraction plane. Such a hysteresis has been independently measured and computed in recent studies of homogeneous transient uniaxial stretching of PS/PS Boger fluids. Flow visualization and velocity field measurements using digital particle image velocimetry (DPIV) show large upstream growth of the corner vortex with increasing Deborah number. At large Deborah numbers, the onset of an elastic instability is observed, first locally as small amplitude fluctuations in the pressure measurements, and then globally as an azimuthal precessing of the upstream corner vortex accompanied by periodic oscillations in the pressure drop across the orifice.

Rothstein, Jonathan P.↗

RELAP-7 Application and Enhancement for FLEX Strategies and ATF Behavior under Extended Loss of AC Power Conditions

This report summarizes the results of a three-year research project sponsored by the U.S. Department of Energy (DOE) Nuclear Energy University Program (NEUP) to enhance and apply the RELAP-7 code by adding and improving several important components (e.g., a mechanistic Reactor Core Isolation Cooling (RCIC) system model) for thermal hydraulic studies of LWRs under ELAP conditions and evaluating the time available for transition to portable FLEX equipment. The project team included University of Massachusetts–Lowell, The Ohio State University, Texas A&M University, Idaho National Laboratory and Oak Ridge National Laboratory. In the Fukushima accident, it was found that the RCIC system played a crucial role in delaying core meltdown by almost three days in Fukushima Daiichi Unit 2, because of self-regulated operation of the steam driven RCIC turbine-pump injection system. Steam flow in the convergent-divergent nozzles of the RCIC Terry turbine is two-phase non-equilibrium transonic flow with homogenous nucleation condensation. To more accurately predict the dynamic process and behavior of the transonic compressible steam flow, a one-dimensional transient two-phase analytical model is presented. A simplified four-fluid model was employed in the present work with the consideration of four separate fluid fields: vapor, liquid film, entrained droplets and condensed droplets. The mass, momentum and energy interactions between the fluids were considered and modeled. An extended seven-equation non-equilibrium critical flow model was developed to obtain the critical pressure and velocities of each phase at the nozzle throat. To predict the wetness in the divergent section, a mechanistic nucleation condensation model was integrated in the nozzle analysis model, considering the generation and consequent growth of droplets. The governing differential equations on a staggered grid were discretized using the second-order Lax-Wendroff scheme with a flux limiter, and the Semi-Implicit Method for Pressure-Linked Equation (SIMPLE) algorithm was employed to solve the discrete linear system. To demonstrate the predictability and reliability of the physical models and the numerical method proposed in the present work, three representative nozzles were modeled and simulated. The results show good agreement with the available experimental data, even for condensation shock. Then, the 1D nozzle model was employed to obtain nozzle flow tables of the Terry turbine nozzle for different working pressures which can cover the operation pressure range of the RCIC system. A mechanistic RCIC turbine-pump system model was developed and implemented in the system code TRACE to simulate dynamic responses of the RCIC system under Beyond Design Basis Accident (BDBA) conditions. The turbine-pump governing equations are based on the control volume approach of the angular momentum balance. The physics based mechanistic RCIC model was developed using the TRACE control system components (i.e., signal variables, control blocks, and tables), and incorporated into a TRACE boiling water reactor (BWR) model. The TRACE model in this report has a detailed nodalization of the reactor pressure vessel (RPV), and all of the major flow paths and system components, including the safety relief valves (SRVs) and the containment suppression pool and drywell. Based on the nozzle flow tables generated from the 1D nozzle model developed, the turbine drive torque can be calculated from table lookup. Since the detailed specifications of the RCIC pump are unavailable, the homologous curves for a Bingham pump were used in the current pump component. A station black-out (SBO) accident test problem was selected to demonstrate the TRACE RCIC model. The short-term SBO simulations were performed for two cladding materials: Zircaloy and FeCrAl, to demonstrate the effect of the accident tolerant fuel cladding on fuel heat-up under BDBA accident conditions. The wetwell plays a vital safety role in SBO and other BWR accident scenarios in that it can reduce containment pressure and supply additional core make-up water. The suppression pool temperature distribution has a very large impact on both RPV and containment pressure. Thus, another novel contribution of the project comes mainly from an improved, systems-level wetwell model which can capture buoyancy-induced thermal stratification effects due to steam injection and condensation. A two-zone stratified wetwell model has been implemented in RELAP-7 and some results from that model are presented. This wetwell model is capable of simulating thermal stratification due to a low steam mass injection rate. With a low mass flow rate, the model assumes that all the steam condenses within the pipe and the resulting plume can be approximated with a purely buoyant, heat-source driven model. The wetwell model developed with these assumptions is adequate to simulate slow transients such as extended SBO transients.

42 ENGINEERING↗

Stationary turbulent closure via the Hopf functional equation

Explicit solutions of the stationary Hopf equation are discussed and their computational possibilities are explored. The motivation is to circumvent the infinite hierarchy of coupled equations for the velocity moments and obtain an exact closure of the steady-state 3D Navier-Stokes equations, without modeling assumptions or truncation. The Hopf formulation of the Navier-Stokes equation is reviewed. A stationary homogeneous solution for 2D flow is displayed and discussed. It is shown how depletion of nonlinearity may arise for 3D forced homogeneous flow. The general 3D forced case is considered and a method for closing the 3D unforced equations with arbitrary boundary conditions is derived.

Shen, Hubert H.↗

A modified restricted Euler equation for turbulent flows with mean velocity gradients

The restricted Euler equation captures many important features of the behavior of the velocity gradient tensor observed in direct numerical simulations (DNS) of isotropic turbulence. However, in slightly more complex flows the agreement is not good, especially in regions of low dissipation. In this paper, it is demonstrated that the Reynolds-averaged restricted Euler equation violates the balance of mean momentum for virtually all homogeneous turbulent flows with only two major exceptions: isotropic and homogeneously-sheared turbulence. A new model equation which overcomes this shortcoming and is more widely applicable is suggested. This modele is derived from the Navier-Stokes equation with a restricted Euler type approximation made on the fluctuating velocity gradient field. Analytical solutions of the proposed modified restricted Euler equation appear to be difficult to obtain. Hence, a strategy for numerically calculating the velocity gradient tensor is developed. Preliminary calculations tend to indicate that the modified restricted Euler equation captures many important aspects of the behavior of the fluctuating velocity gradients in anisotropic homogeneous turbulence.

Girimaji, Sharath S.↗

Numerical simulation of turbulence in the presence of shear

The numerical calculations are presented of the large eddy structure of turbulent flows, by use of the averaged Navier-Stokes equations, where averages are taken over spatial regions small compared to the size of the computational grid. The subgrid components of motion are modeled by a local eddy-viscosity model. A new finite-difference scheme is proposed to represent the nonlinear average advective term which has fourth-order accuracy. This scheme exhibits several advantages over existing schemes with regard to the following: (1) the scheme is compact as it extends only one point away in each direction from the point to which it is applied; (2) it gives better resolution for high wave-number waves in the solution of Poisson equation, and (3) it reduces programming complexity and computation time. Examples worked out in detail are the decay of isotropic turbulence, homogeneous turbulent shear flow, and homogeneous turbulent shear flow with system rotation.

Shaanan, S.↗

Flow Reduction in Pore Networks of Packed Silica Nanoparticles: Insights from Mesoscopic Fluid Models

A modified many-body dissipative particle dynamics (mDPD) model is rigorously calibrated to achieve realistic fluid–fluid/solid interphase properties and applied for mesoscale flow simulations to elucidate the transport mechanisms of heptane liquid and water, respectively, through pore networks formed by packed silica nanoparticles with a uniform diameter of 30 nm. Two million CPU core hours were used to complete the simulation studies. Results show reduction of permeability by 54–64% in heptane flow and by 88–91% in water flow, respectively, compared to the Kozeny–Carman equation. In these nanopores, a large portion of the fluids are in the near-wall regions and thus not mobile due to the confinement effect, resulting in reduced hydraulic conductivity. Moreover, intense oscillations in the calculated flow velocities also indicate the confinement effect that contests the external driven force to flow. Here, the generic form of Darcy’s law is considered valid for flow through homogeneous nanopore networks, while permeability depends collectively on pore size and surface wettability. This fluid-permeability dependency is unique to flow in nanopores. In addition, potential dependence of permeability on pore connectivity is observed when the porosity remains the same in different core specimens.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effects of organized turbulence structures on the phase distortion in a coherent optical beam propagating through a turbulent shear flow

Phase distortion in a coherent optical beam propagating through a turbulent shear flow is studied. The instantaneous distribution of the index refraction is represented by a passive-scalar field in a computed homogeneous shear flow. The flow contains organized vortical structures (hairpin eddies), which are characteristic of turbulent shear flows. The phase distortion induced by turbulent fluctuations is calculated from the optical path difference through the flow. A conceptual model is proposed for the distribution of scalar fluctuations produced by the hairpin vortices in the shear flow. It is shown that the phase distortion of an optical beam can be minimized by propagating the beam at an angle approximately normal to the organized vortical structures in a turbulent shear flow.

Truman, C. Randall↗

The Helium Warm Breeze in IBEX Observations As a Result of Charge-exchange Collisions in the Outer Heliosheath

We simulated the signal due to neutral He atoms, observed by the Interstellar Boundary Explorer ( IBEX ), assuming that charge-exchange collisions between neutral He atoms and He{sup +} ions operate everywhere between the heliopause and a distant source region in the local interstellar cloud, where the neutral and charged components are in thermal equilibrium. We simulated several test cases of the plasma flow within the outer heliosheath (OHS) and investigated the signal generation for plasma flows both in the absence and in the presence of the interstellar magnetic field (ISMF). We found that a signal in the portion of IBEX data identified as being due to the Warm Breeze (WB) does not arise when a homogeneous plasma flow in front of the heliopause is assumed, but it appears immediately when any reasonable disturbance in its flow due to the presence of the heliosphere is assumed. We obtained a good qualitative agreement between the data selected for comparison and the simulations for a model flow with the velocity vector of the unperturbed gas and the direction and intensity of magnetic field adopted from recent determinations. We conclude that direct-sampling observations of neutral He atoms at 1 au from the Sun are a sensitive tool for investigating the flow of interstellar matter in the OHS, that the WB is indeed the secondary population of interstellar helium, which was hypothesized earlier, and that the WB signal is consistent with the heliosphere distorted from axial symmetry by the ISMF.

79 ASTRONOMY AND ASTROPHYSICS↗

Development of a Time-Height Profile Assimilation Technique for Large-Eddy Simulation

Mesoscale-to-microscale coupling (MMC) aims to address the limited scope of traditional large-eddy simulations by driving the microscale flow with information concerning large-scale weather patterns provided by mesoscale models. We present a new offline MMC technique for horizontally homogeneous microscale flow conditions, in which internal forcing terms are computed based on mesoscale time–height profiles of mean-flow quantities. The advantage of such an approach is that it can be used to drive a microscale simulation with either mesoscale or observational data, and that it does not rely on specific terms in the mesoscale budget equations, which are typically not part of the default output of a mesoscale solver. The performance of the proposed profile assimilation technique is assessed based on the simulation of a typical diurnal cycle over the Scaled Wind Farm Technology site in west Texas. Results indicate that simple data assimilation techniques lead to unphysically high levels of shear and turbulence caused by the algorithm’s inability to cope with inaccuracies in the mesoscale time–height profiles. Modifying the algorithm to account for vertical coherence in the mesoscale source terms gives the microscale solver a greater ability to correct the provided mesoscale time–height profiles, leading to improved predictions of shear and turbulence statistics. The resulting turbulence statistics are in good agreement with meteorological tower observations and simulation results obtained with state-of-the-art coupling techniques using mesoscale budget components.

data assimilation↗

Instability of gravity flows on a slope

A Hamiltonian version of contour dynamics is formulated for the model of a potential slope flow of homogeneous incompressible fluid. The particle-like solutions that play the role of structural elements in the disintegration of strongly perturbed slope flows are studied in terms of this approach. Investigation of the solution instability mechanism has shown that two collapse scenarios are realized, depending on the slope steepness. The singularity for the surface shape develops according to the law (t - t{sub 0}){sup -1/3} on a vertical slope and slightly more slowly, according to the law (t - t{sub 0}){sup -2/7}, where t{sub 0} is the collapse time, on a nonvertical slope. A sufficient collapse criterion that allows this effect to be judged from the first three integrals of motion has been established.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Simulations of material mixing in laser-driven reshock experiments

We perform simulations of a laser-driven reshock experiment [Welser-Sherrill et al., High Energy Density Phys. (unpublished)] in the strong-shock high energy-density regime to better understand material mixing driven by the Richtmyer-Meshkov instability. Validation of the simulations is based on direct comparison of simulation and radiographic data. Simulations are also compared with published direct numerical simulation and the theory of homogeneous isotropic turbulence. Despite the fact that the flow is neither homogeneous, isotropic nor fully turbulent, there are local regions in which the flow demonstrates characteristics of homogeneous isotropic turbulence. We identify and isolate these regions by the presence of high levels of turbulent kinetic energy (TKE) and vorticity. After reshock, our analysis shows characteristics consistent with those of incompressible isotropic turbulence. Self-similarity and effective Reynolds number assessments suggest that the results are reasonably converged at the finest resolution. Our results show that in shock-driven transitional flows, turbulent features such as self-similarity and isotropy only fully develop once de-correlation, characteristic vorticity distributions, and integrated TKE, have decayed significantly. Finally, we use three-dimensional simulation results to test the performance of two-dimensional Reynolds-averaged Navier-Stokes simulations. In this context, we also test a presumed probability density function turbulent mixing model extensively used in combustion applications.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗