Search NASA⌕ Search

SEARCH · Search NASA

Results for “Hydrogen”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

New potentials for conventional aircraft when powered by hydrogen-enriched gasoline

Hydrogen enrichment for aircraft piston engines is under study in a new NASA program. The objective of the program is to determine the feasibility of inflight injection of hydrogen in general aviation aircraft engines to reduce fuel consumption and to lower emission levels. A catalytic hydrogen generator will be incorporated as part of the air induction system of a Lycoming turbocharged engine and will generate hydrogen by breaking down small amounts of the aviation gasoline used in the normal propulsion system. This hydrogen will then be mixed with gasoline and compressed air from the turbocharger before entering the engine combustion chamber. The special properties of the hydrogen-enriched gasoline allow the engine to operate at ultralean fuel/air ratios, resulting in higher efficiencies and hence less fuel consumption. This paper summarizes the results of a systems analysis study. Calculations assuming a Beech Duke aircraft indicate that fuel savings on the order of 20% are possible. An estimate of the potential for the utilization of hydrogen enrichment to control exhaust emissions indicates that it may be possible to meet the 1979 Federal emission standards.

Menard, W. A.↗
NASA NTRS1977

Mechanical properties of several nickel alloys in hydrogen at elevated temperatures

Tests were performed to determine low cycle fatigue and crack growth rate properties of one iron-base and two forms of one cast nickel-base alloy. The alloys were tested in various forms and/or heat-treat conditions that are proposed for use in a high-pressure hydrogen or a hydrogen-water vapor environment. Some general conclusions can be made comparing the results of tests in a hydrogen environment with those in a hydrogen-water vapor environment. The hydrogen-water vapor environment caused a 50 percent average reduction in fatigue life, indicating extreme degradation when compared with tests conducted in air, for Incoloy 903 at 1033 K (1400 F). Crack growth rates increased significantly for all materials with increasing test temperature. A very significant increase (three orders of magnitude) in crack growth rate occurred for Incoloy 903 tested in the hydrogen-water vapor environment when compared with testing done in hydrogen along at 922 K (1200 F).

Warren, J. R.↗
NASA NTRS1976

The NASA Hydrogen Energy Systems Technology study - A summary

This study is concerned with: hydrogen use, alternatives and comparisons, hydrogen production, factors affecting application, and technology requirements. Two scenarios for future use are explained. One is called the reference hydrogen use scenario and assumes continued historic uses of hydrogen along with additional use for coal gasification and liquefaction, consistent with the Ford technical fix baseline (1974) projection. The expanded scenario relies on the nuclear electric economy (1973) energy projection and assumes the addition of limited new uses such as experimental hydrogen-fueled aircraft, some mixing with natural gas, and energy storage by utilities. Current uses and supply of hydrogen are described, and the technological requirements for developing new methods of hydrogen production are discussed.

Laumann, E. A.↗
NASA NTRS1977

Departures of the electron energy distribution from a Maxwellian in hydrogen. I - Formulation and solution of the electron kinetic equation. II - Consequences

The problem of calculating the steady-state free-electron energy distribution in a hydrogen gas is considered in order to study departures of that distribution from a Maxwellian at sufficiently low degrees of ionization. A model kinetic equation is formulated and solved analytically for the one-particle electron distribution function in a steady-state partially ionized hydrogen gas, and it is shown that the formal solution can be accurately approximated by using the WKB method. The solutions obtained indicate that the high-energy tail of the distribution is susceptible to distortion by imbalanced inelastic collisions for ionization fractions not exceeding about 0.1 and that such departures from a Maxwellian can lead to significant changes in the collisional excitation and ionization rates of ground-state hydrogen atoms. Expressions for the electron-hydrogen collision rates are derived which explicitly display their dependence on the hydrogen departure coefficients. The results are applied in order to compare self-consistent predictions with those based on the a priori assumption of a Maxwellian distribution for models of the thermal ionization equilibrium of hydrogen in the optically thin limit, spectral-line formation by a gas consisting of two-level atoms, and radiative transfer in finite slabs by a gas of four-level hydrogen atoms.

Shoub, E. C.↗
NASA NTRS1977

Self discharge of nickel-hydrogen cells

Values for the capacity loss with time, naturally on open circuit stand, and information regarding the minimum amount of circuit charge needed to keep the cell charged can be determined from the self-discharge behavior of nickel hydrogen cells. Furthermore, the rate of reaction between hydrogen and a charged nickel electrode is also open for nickel cadmium batteries. In a nickel hydrogen cell, the hydrogen is stored as pressurized gas and the cell stack with the charge that is oxidized nickel-hydroxide electrode is in direct contact with the hydrogen. Therefore, the rate of reaction can be measured easily and precisely by monitoring the charge, the change in hydrogen pressure with time. Measures made on twelve 15 ampere hour nickel hydrogen cells of different stack configurations built for COMSAT are discussed.

Holleck, G.↗
NASA NTRS1979

Concepts for solar production of hydrogen

Some basic technical approaches to producing hydrogen from solar energy are surveyed. Solar energy forms are divided into: (1) direct solar radiation and (2) indirect forms such as wind and ocean thermal gradient. Technical approaches are separated into: (1) direct hydrogen production from the action of sunlight on some substrate, (2) hydrogen production from sunlight via an intermediate form of energy such as heat and electricity, and (3) hydrogen production from indirect solar energy via an intermediate energy form. It is concluded that while hydrogen from solar energy will be expensive by present standards, the depletion of fossil fuels will cause solar hydrogen to emerge as one of the few alternatives to a nuclear-electric or nuclear-electric-hydrogen energy system.

Hanson, J. A.↗
NASA NTRS1981

Hydrogen engines based on liquid fuels, a review

The concept of storing hydrogen as part of a liquid fuel, such as gasoline or methanol, and subsequent onboard generation of the hydrogen from such liquids, is reviewed. Hydrogen generation processes, such as steam reforming, partial oxidation, and thermal decomposition are evaluated in terms of theoretical potential and practical limitations, and a summary is presented on the major experimental work on conversion of gasoline and methanol. Results of experiments indicate that onboard hydrogen generation from methanol is technically feasible and will yield substantial improvements in fuel economy and emissions, especially if methanol decomposition is brought about by the use of engine exhaust heat; e.g., a methanol decomposition reactor of 3.8 provides hydrogen-rich gas for a 4 cylinder engine (1.952), and 80% of the methanol is converted, engine exhaust gas being the only heat supply. A preliminary outline of the development of a methanol-based hydrogen engine and a straight hydrogen engine is presented.

Houseman, J.↗
NASA NTRS1984

Experimental and analytical analyses of the mechanisms governing the dispersion of flammable clouds formed by liquid hydrogen spills

This paper presents the initial findings of hydrogen vapor cloud dispersion experiments conducted by NASA. The experiments were performed to obtain basic information regarding the physical phenomena governing the dispersion of flammable clouds formed as the result of spills of large quantities of liquid hydrogen. The experiments consisted of ground spills of up to 5.7 cu m of liquid hydrogen with spill durations of approx. 35 s. Instrumented towers, located downwind of the spill site, gathered data on the temperature, hydrogen concentration and turbulence levels as the hydrogen vapor cloud drifted downwind. Preliminary results of the experiments indicate that, for rapid spills, thermal and momentum-induced turbulences cause the cloud to disperse to safe concentration levels and become positively buoyant long before mixing due to normal atmospheric turbulence becomes a major factor. An adiabatic mixing model has been developed to deduce hydrogen-air mixture ratios for temperature measurements obtained within the cloud formed by liquid hydrogen spills.

Witcofski, R. D.↗
NASA NTRS1986

Oxygen recombination in individual pressure vessel nickel-hydrogen batteries

A metal-hydrogen cell is described which avoids damage and retards flooding of the hydrogen electrodes by providing for chemical recombination of oxygen and hydrogen in areas or sites remote from the hydrogen electrodes. In the metal-hydrogen cell, a plurality of electrical cell units are place in a back to back relationship. The cells may be lined with a wick, having one or more catalyzed sites on the inner surface of the cell. Separators disposed between the respective metal and hydrogen electrodes of each cell unit are provided with gas directing notches around their peripheries to facilitate the desired movement of gasses within the metal-hydrogen cell. Any two metal electrodes separated by a gas screen are provided with gas tight sealing means between the electrodes at each aperature. The sealing means may be a fing of rubber or elastomeric material which is somewhat compressible but nonreactive with other materials in the cell.

Smithrick, J. J.↗
NASA NTRS1987

Effect of water on hydrogen permeability

Doping of hydrogen with CO and CO2 was developed to reduce hydrogen permeation in Stirling engines by forming a low permeability oxide coating on the inner surface of the heater head tubes. Although doping worked well, under certain circumstances the protective oxide could be chemically reduced by the hydrogen in the engine. Some oxygen is required in the hydrogen to prevent reduction. Eventually, all the oxygen in the hydrogen gas - whatever its source - shows up as water. This is the result of hydrogen reducing the CO, CO2, or the protective inner surface oxides. This water can condense in the engine system under the right conditions. If the concentration of water vapor is reduced to a low enough level, the hydrogen can chemically reduce the oxide coating, resulting in an increase in permeability. This work was done to define the minimum water content required to avoid this reduction in the oxide coating. The results of this testing show that a minimum of approximately 750 ppm water is required to prevent an increase in permeability of CG-27, a high temperature metal alloy selected for Stirling engine heater tubes.

Hulligan, David↗
NASA NTRS1988

Methods of extracting hydrogen from lunar soil

Increasing interest in establishing a lunar base has generated considerable study on the utilization of lunar resources. Because of its importance in producing water, reducing oxides, and serving as a fuel for orbital tranfer vehicles, hydrogen is of prime importance as a resource. Lowman (1985) states that hydrogen would greatly facilitate the establishment of an autonomous permanent colony, and he calls hydrogen the most valuable lunar resource. Through the centuries, hydrogen has been embedded in lunar soil by the solar wind. The hydrogen can be extracted by heating the soil to 900 C (Carr et al, 1987). In order to obtain hydrogen on the lunar surface, an extraction method must be developed which will not only be reliable but also economically feasible. Three heating methods are examined for possible use in extracting hydrogen from lunar soil.

Bustin, Roberta↗
NASA NTRS1989

Operating characteristics of a hydrogen-argon plasma torch for supersonic combustion applications

The residence time of the combustible mixture in the combustion chamber of a scramjet engine is much less than the time normally required for complete combustion. Hydrogen and hydrocarbon fuels require an ignition source under conditions typically found in a scramjet combustor. Analytical studies indicate that the presence of hydrogen atoms should greatly reduce the ignition delay in this environment. Because hydrogen plasmas are prolific sources of hydrogen atoms, a low-power, uncooled hydrogen plasma torch has been built and tested to evaluate its potential as a possible flame holder for supersonic combustion. The torch was found to be unstable when operated on pure hydrogen; however, stable operation could be obtained by using argon as a body gas and mixing in the desired amount of hydrogen. The stability limits of the torch are delineated and its electrical and thermal behavior documented. An average torch thermal efficiency of around 88 percent is demonstrated.

Barbi, E.↗
NASA NTRS1988

The effect of hydrogen on the deformation and fracture of PWA 1480

The effect of internal hydrogen on mechanical properties and fracture behavior is studied in the single-crystal nickel-base superalloy PWA 1480. In particular, plane strain fracture toughness and tensile tests have been performed in hydrogen-free samples and hydrogen-gas phase-charged samples in two different sample orientations. The mechanical properties, as well as the fracture process, were found to be very dependent on orientation. Hydrogen did not affect the yield strength but reduced the uniform tensile elongation more than 75 percent. However, hydrogen reduced the tensile reduction-in-area and the fracture toughness by only 10 percent. Cleavage of the eutectic gamma-prime, as well as the role of hydrogen trapping, will be discussed. These results will be analyzed in terms of the effects that orientation, microstructure, and hydrogen have on the fracture process.

Walston, W. S.↗
NASA NTRS1990

Atomic hydrogen as a launch vehicle propellant

An analysis of several atomic hydrogen launch vehicles was conducted. A discussion of the facilities and the technologies that would be needed for these vehicles is also presented. The Gross Liftoff Weights (GLOW) for two systems were estimated; their specific impulses (I sub sp) were 750 and 1500 lb(sub f)/s/lb(sub m). The atomic hydrogen launch vehicles were also compared to the currently planned Advanced Launch System design concepts. Very significant GLOW reductions of 52 to 58 percent are possible over the Advanced Launch System designs. Applying atomic hydrogen propellants to upper stages was also considered. Very high I(sub sp) (greater than 750 lb(sub f)/s/lb(sub m)) is needed to enable a mass savings over advanced oxygen/hydrogen propulsion. Associated with the potential benefits of high I(sub sp) atomic hydrogen are several challenging problems. Very high magnetic fields are required to maintain the atomic hydrogen in a solid hydrogen matrix. The magnetic field strength was estimated to be 30 kilogauss (3 Tesla). Also the storage temperature of the propellant is 4 K. This very low temperature will require a large refrigeration facility for the launch vehicle. The design considerations for a very high recombination rate for the propellant are also discussed. A recombination rate of 210 cm/s is predicted for atomic hydrogen. This high recombination rate can produce very high acceleration for the launch vehicle. Unique insulation or segmentation to inhibit the propellant may be needed to reduce its recombination rate.

Palaszewski, Bryan A.↗
NASA NTRS1990

Hydrogen permeation, diffusion and solubility in IN-100 and Waspaloy

An attempt has been made to determine the permeation rate of hydrogen in IN-100 and Waspaloy by determining the evolution rate of hydrogen from a closed capsule of the test materials. Enclosed vanadium hydride was the source of hydrogen in the capsule. The presentation discusses the treatment of data and assesses the validity of the techniques in permeation measurement. In addition to permeation experiments, the solubility and diffusion of hydrogen in IN-100 and Waspaloy were also determined. For hydrogen diffusion in Waspaloy, Delta H was 38.5 kJ and D(0) was 0.0026 sq cm/sec. For IN-100, Delta H was 68.2 kJ and D(0) was 0.059 sq cm /sec. Both IN-100 and Waspaloy exhibited limited solubility of hydrogen at pressures up to 340 atmospheres hydrogen.

Khan, A. S.↗
NASA NTRS1991

Composite material systems for hydrogen management

The task of managing hydrogen entry into elevated temperature structural materials employed in turbomachinery is a critical engineering area for propulsion systems employing hydrogen or decomposable hydrocarbons as fuel. Extant structural materials, such as the Inconel series, are embrittled by the ingress of hydrogen in service, leading to a loss of endurance and general deterioration of load-bearing dependability. Although the development of hydrogen-insensitive material systems is an obvious engineering option, to date insensitive systems cannot meet the time-temperature-loading service extremes encountered. A short-term approach that is both feasible and technologically sound is the development and employment of hydrogen barrier coatings. The present project is concerned with developing, analyzing, and physically testing laminate composite hydrogen barrier systems, employing Inconel 718 as the structural material to be protected. Barrier systems will include all metallic, metallic-to-ceramic, and, eventually, metallic/ceramic composites as the lamellae. Since space propulsion implies repetitive engine firings without earth-based inspection and repair, coating durability will be closely examined, and testing regimes will include repetitive thermal cycling to simulate damage accumulation. The target accomplishments include: generation of actual hydrogen permeation data for metallic, ceramic-metallic, and hybrid metallic/ceramic composition barrier systems, practically none of which is currently extant; definition of physical damage modes imported to barrier systems due to thermal cycling, both transient temperature profiles and steady-state thermal mismatch stress states being examined as sources of damage; and computational models that incorporate general laminate schemes as described above, including manufacturing realities such as porosity, and whatever defects are introduced through service and characterized during the experimental programs.

Pangborn, R. N.↗
NASA NTRS1991

The interaction of hydrogen with metal alloys

Hydrogen diffusion coefficients were measured for several alloys, and these were determined to be about the same at 25 C for all alloys investigated. The relation of structure, both metallurgical and crystallographic, to the observed hydrogen distribution on charging was investigated, as well as the role of hydride formation in the hydrogen resistance of metal alloys. An attempt was made to correlate the structures and compositions of metal alloys as well as other parameters with the ratios of their notched tensile strengths in hydrogen to that in helium, R(H2/He), which are believed to represent a measure of their hydrogen resistance. Evidence supports the belief that hydrogen permeability and hydrogen resistance are increased by smaller grain sizes for a given alloy composition.

Danford, M. D.↗
NASA NTRS1990

The effect of hydrogen on the deformation and fracture behavior of a single crystal nickel-base superalloy

The room temperature and 300 C tensile behavior of a single crystal superalloy, PWA 1480, has been studied as a function of internal hydrogen concentration and microstructure. Hydrogen is trapped at the porosity and eutectic gamma/gamma in the microstructure, and the effect of these trapping sites on the tensile behavior will be discussed. There is no effect of hydrogen on strength, however, the strain to failure decreases steadily with increasing hydrogen content up to 200 ppm. Cleavage of the eutectic gamma/gamma occurs without hydrogen, but the presence of internal hydrogen causes cracking in the eutectic gamma/gamma at a much earlier stage of deformation leading to a small total strain. In contrast to many superalloys with a high volume fraction of gamma precipitates, there was no evidence of shearing of the gamma, and it was found that at all strains the dislocations are trapped in the gamma matrix. The effect of hydrogen on this behavior and its relation to fracture is described.

Walston, W. S.↗