Search NASA⌕ Search

SEARCH · Search NASA

Results for “IMPACT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

Mapping and Characterizing the Visual Impacts of the Existing US Wind Turbine Fleet

Visual impacts of wind turbines have been a persistent concern for wind energy development in the United States (US) for decades and remain a major source of project delays and cancellations. Assessments of visual impacts are frequently performed at a local scale for individual projects, but a comprehensive understanding of broader geographic patterns in visual impacts across the US is lacking. This paper presents a visual impact assessment of the existing land-based wind turbine fleet of the contiguous United States (CONUS). The assessment combines geographic information systems and 3D simulation methods to account for key factors driving the visual magnitude of impacts from the installed turbines. The results indicate that, despite the deployment of approximately 70,000 turbines and over 144 gigawatts of land-based wind in the CONUS, the visual impacts are very small when measured as a proportion of land area, population, and sensitive visual resources. Nonetheless, visual impacts are not evenly distributed: people experience a concentrated share in a small number of natural settings, primarily including plains, prairies, and deserts. Finally, we find that although increased density of wind development consistently leads to visual impacts across a greater proportion of land, it does not always lead to impacts to a greater share of the population. These findings suggest that visual impacts from wind energy are generally well-mitigated across the CONUS to date but also highlight the need for a deeper understanding of landscape sensitivity and individual perceptions of wind turbines in the most heavily impacted natural settings.

3D simulation↗

Experimental Measurement of Frozen and Partially Melted Water Droplet Impact Dynamics

High-speed video of single frozen water droplets impacting a surface was acquired. The droplets diameter ranged from 0.4 mm to 0.9 mm and impacted at velocities ranging from 140 m/sec to 309 m/sec. The techniques used to freeze the droplets and launch the particles against the surfaces is described in this paper. High-speed video was used to quantify the ice accretion area to the surface for varying impact angles (30 deg, 45 deg, 60 deg), impacting velocities, and break-up angles. An oxygen /acetylene cross-flow flame used to ensure partial melting of the traveling frozen droplets is also discussed. A linear relationship between impact angle and ice accretion is identified for fully frozen particles. The slope of the relationship is affected by impact speed. Perpendicular impacts, i.e. 30 deg, exhibited small differences in ice accretion for varying velocities, while an increase of 60% in velocity from 161 m/sec to 259 m/sec, provided an increase on ice accretion area of 96% at an impact angle of 60 deg. The increase accretion area highlights the importance of impact angle and velocity on the ice accretion process of ice crystals. It was experimentally observed that partial melting was not required for ice accretion at the tested velocities when high impact angles were used (45 and 60 deg). Partially melted droplets doubled the ice accretion areas on the impacting surface when 0.0023 Joules were applied to the particle. The partially melted state of the droplets and a method to quantify the percentage increase in ice accretion area is also described in the paper.

Impact Dynamics↗

Development of impact design methods for ceramic gas turbine components

Impact damage prediction methods are being developed to aid in the design of ceramic gas turbine engine components with improved impact resistance. Two impact damage modes were characterized: local, near the impact site, and structural, usually fast fracture away from the impact site. Local damage to Si3N4 impacted by Si3N4 spherical projectiles consists of ring and/or radial cracks around the impact point. In a mechanistic model being developed, impact damage is characterized as microcrack nucleation and propagation. The extent of damage is measured as volume fraction of microcracks. Model capability is demonstrated by simulating late impact tests. Structural failure is caused by tensile stress during impact exceeding material strength. The EPIC3 code was successfully used to predict blade structural failures in different size particle impacts on radial and axial blades.

Song, J.↗

Effect of low-speed impact damage and damage location on behavior of composite panels

The effect of low speed impact damage on the compression and tension strength of thin and moderately thick composite specimens was investigated. Impact speed ranged from 50 to 550 ft./sec., with corresponding impact energies from 0.25 to 30.7 ft. x lb. Impact locations were near the center of the specimen or near a lateral unloaded edge. In this study, thin specimens with only 90 degree and + or - 45 degree plies that were impacted away from the unloaded edge suffered less reduction in load carrying capability because of impact damage than of the same specimens impacted near the unloaded edge. Failure loads of thicker compression loaded specimens with a similar stacking sequence were independent of impact location. Failure loads of thin tension loaded specimens with 0 degree plies was independent of impact location, whereas failure loads of thicker compression loaded specimens with 0 degree plies were dependent upon impact location. A finite element analysis indicated that high axial strains occurred near the unloaded edges of the postbuckled panels. Thus, impacts near the unloaded edge would significantly affect the behavior of the postbuckled panel.

Jegley, Dawn C.↗

LDEF's map experiment foil perforations yield hypervelocity impact penetration parameters

The space exposure of LDEF for 5.75 years, forming a host target in low earth orbit (LEO) orbit to a wide distribution of hypervelocity particulates of varying dimensions and different impact velocities, has yielded a multiplicity of impact features. Although the projectile parameters are generally unknown and, in fact not identical for any two impacts on a target, the great number of impacts provides statistically meaningful basis for the valid comparison of the response of different targets. Given sufficient impacts for example, a comparison of impact features (even without knowledge of the project parameters) is possible between: (1) differing material types (for the same incident projectile distribution); (2) differing target configurations (e.g., thick and thin targets for the same material projectiles; and (3) different velocities (using LDEF's different faces). A comparison between different materials is presented for infinite targets of aluminum, Teflon, and brass in the same pointing direction; the maximum finite-target penetration (ballistic limit) is also compared to that of the penetration of similar materials comprising of a semi-infinite target. For comparison of impacts on similar materials at different velocities, use is made of the pointing direction relative to LDEF's orbital motion. First, however, care must be exercised to separate the effect of spatial flux anisotropies from those resulting from the spacecraft velocity through a geocentrically referenced dust distribution. Data comprising thick and thin target impacts, impacts on different materials, and in different pointing directions is presented; hypervelocity impact parameters are derived. Results are also shown for flux modeling codes developed to decode the relative fluxes of Earth orbital and unbound interplanetary components intercepting LDEF. Modeling shows the west and space pointing faces are dominated by interplanetary particles and yields a mean velocity of 23.5 km/s at LDEF, corresponding to a V(infinity) Earth approach velocity = 20.9 km/s. Normally resolved average impact velocities on LDEF's cardinal point faces are shown. As 'excess' flux on the east, north, and south faces is observed, compatible with an Earth orbital component below some 5 microns in particle diameter.

Mcdonnell, J. A. M.↗

Relevance of impacter shape to nonvisible damage and residual tensile strength of a thick graphite/epoxy laminate

A study was made to determine the relevance of impacter shape to nonvisible damage and tensile residual strength of a 36 mm thick graphite/epoxy motor case. The shapes of the impacters were as follows: 12.7 mm and 25.4 mm diameter hemispheres, a sharp corner, and a 6.3 mm diameter bolt-like rod. The investigation revealed that damage initiated when the contact pressure exceeded a critical level. However, the damage was not visible on the surface until an even higher pressure was exceeded. The impact energy to initiate damage or cause visible damage on the surface increased approximately with impacter diameter to the third power. The reduction in strength for nonvisible damage increased with increasing diameter, 9 and 30 percent for the 12.7 mm and 25.4 mm diameter hemispheres, respectively. The corner impacter made visible damage on the surface for even the smallest impact energy. The rod impacter acted like a punch and sliced through the composite. Even so, the critical level of pressure to initiate damage was the same for the rod and hemispherical impacters. Factors of safety for nonvisible damage increased with increasing kinetic energy of impact. The effects of impacter shape on impact force, damage size, damage visibility, and residual tensile strength were predicted quite well assuming Hertzian contact and using maximum stress criteria and a surface crack analysis.

Poe, Clarence C., Jr.↗

The Cretaceous-Tertiary (K/T) impact: One or more source craters?

The Cretaceous-Tertiary (K/T) boundary is marked by signs of a worldwide catastrophe, marking the demise of more than 50 percent of all living species. Ever since Alvarez et al. found an enrichment of IR and other siderophile elements in rocks marking the K/T boundary and interpreted it as the mark of a giant asteroid (or comet) impact, scientists have tried to understand the complexities of the K/T boundary event. The impact theory received a critical boost by the discovery of shocked minerals that have so far been found only in association with impact craters. One of the problems of the K/T impact theory was, and still is, the lack of an adequate large crater that is close to the maximum abundance of shocked grains in K/T boundary sections, which was found to occur in sections in Northern America. The recent discovery of impact glasses from a K/T section in Haiti has been crucial in establishing a connection with documented impact processes. The location of the impact-glass findings and the continental nature of detritus found in all K/T sections supports at least one impact site near the North American continent. The Manson Impact Structure is the largest recognized in the United States, 35 km in diameter, and has a radiometric age indistinguishable from that of the Cretaceous-Tertiary (K/T) boundary. Although the Manson structure may be too small, it may be considered at least one element of the events that led to the catastrophic loss of life and extinction of many species at that time. A second candidate for the K/T boundary crater is the Chicxulub structure, which was first suggested to be an impact crater more than a decade ago. Only recently, geophysical studies and petrological (as well as limited chemical) analyses have indicated that this buried structure may in fact be of impact origin. At present we can conclude that the Manson crater is the only confirmed crater of K/T age, but Chicxulub is becoming a strong contender; however, detailed geochemical, geochronological, and isotopic data are necessary to provide definitive evidence.

Koeberl, Christian↗

Hypervelocity impact survivability experiments for carbonaceous impactors

We performed a series of hypervelocity impact experiments using carbon-bearing impactors (diamond, graphite, fullerenes, phthalic acid crystals, and Murchison meteorite) into Al plate at velocities between 4.2 and 6.1 km/s. These tests were made to do the following: (1) determine the survivability of carbon forms and organize molecules in low hypervelocity impact; (2) characterize carbonaceous impactor residues; and (3) determine whether or not fullerenes could form from carbonaceous impactors, under our experimental conditions, or survive as impactors. An analytical protocol of field emission SEM imagery, SEM-EDX, laser Raman spectroscopy, single and 2-stage laser mass spectrometry, and laser induced fluorescence (LIF) found the following: (1) diamonds did not survive impact at 4.8 km/s, but were transformed into various forms of disordered graphite; (2) intact, well-ordered graphite impactors did survive impact at 5.9 km/sec, but were only found in the crater bottom centers; the degree of impact-induced disorder in the graphite increases outward (walls, rims, ejecta); (3) phthalic acid crystals were destroyed on impact (at 4.2 km/s, although a large proportion of phthalic acid molecules did survive impact); (4) fullerenes did not form as products of carbonaceous impactors (5.9 - 6.1 km/s, fullerene impactor molecules mostly survived impact at 5.9 km/s; and (5) two Murchison meteorite samples (launched at 4.8 and 5.9 km/s) show preservation of some higher mass polycyclic aromatic hydrocarbons (PAHs) compared with the non-impacted sample. Each impactor type shows unique impactor residue morphologies produced at a given impact velocity. An expanded methodology is presented to announce relatively new analytical techniques together with innovative modifications to other methods that can be used to characterize small impact residues in LDEF craters, in addition to other acquired extraterrestrial samples.

Bunch, T. E.↗

Effect of low-speed impact damage and damage location on behavior of composite panels

An investigation of the effects of low-speed impact damage on the compression and tension strength of thin (less than .05 inches thick) and moderately thick (between .12 and .17 inches thick) composite specimens was conducted. Impact speeds ranged from 50 to 550 ft/sec (impact energies from .25 to 30.7 ft-lb) and impact locations were near or away from a lateral unloaded edge. In this study, thin tension-loaded or compression-loaded specimens with only 90 deg and +/- 40 deg plies which were impacted away from the unloaded edge suffered less reduction in maximum load-carrying capability due to impact damage than the same specimens impacted near the unloaded edge. Unlike the thin laminates, failure loads of thicker compression-loaded specimens with a similar stacking sequence were independent of impact location. Failure loads of thin tension-loaded specimens with 0 deg plies were independent of impact location while failure loads of thicker compression-loaded specimens with 0 deg plies were dependent upon impact location. A finite-element analysis of strain distributions across the panel width indicated that high axial strains occur near the unloaded edges of postbuckled panels, indicating that impacts near the unloaded edge would significantly effect the behavior of postbuckled panels.

Jegley, Dawn↗

Impact damage resistance of composite fuselage structure, part 2

The strength of laminated composite materials may be significantly reduced by foreign object impact induced damage. An understanding of the damage state is required in order to predict the behavior of structure under operational loads or to optimize the structural configuration. Types of damage typically induced in laminated materials during an impact event include transverse matrix cracking, delamination, and/or fiber breakage. The details of the damage state and its influence on structural behavior depend on the location of the impact. Damage in the skin may act as a soft inclusion or affect panel stability, while damage occurring over a stiffener may include debonding of the stiffener flange from the skin. An experiment to characterize impact damage resistance of fuselage structure as a function of structural configuration and impact threat was performed. A wide range of variables associated with aircraft fuselage structure such as material type and stiffener geometry (termed, intrinsic variables) and variables related to the operating environment such as impactor mass and diameter (termed, extrinsic variables) were studied using a statistically based design-of-experiments technique. The experimental design resulted in thirty-two different 3-stiffener panels. These configured panels were impacted in various locations with a number of impactor configurations, weights, and energies. The results obtained from an examination of impacts in the skin midbay and hail simulation impacts are documented. The current discussion is a continuation of that work with a focus on nondiscrete characterization of the midbay hail simulation impacts and discrete characterization of impact damage for impacts over the stiffener.

Dost, Ernest F.↗

Application of impact dampers in vibration control of flexible structures

Impact dampers belong to the category of passive vibration devices used to attenuate the vibration of discrete and continuous systems. An impact damper generally consists of a mass which is allowed to travel freely between two defined stops. Under the right conditions, the vibration of the structure to which the impact damper is attached will cause the mass of the impact damper to strike the structure. Previous analytical and experimental research work on the effect of impact dampers in attenuating the vibration of discrete and continuous systems have demonstrated their effectiveness. It has been shown in this study that impact dampers can increase the intrinsic damping of a lightly-damped flexible structure. The test structure consists of a slender flexible beam supported by a pin-type support at one end and supported by a linear helical flexible spring at another location. Sinusoidal excitation spanning the first three natural frequencies was applied in the horizontal plane. The orientation of the excitation and the test structure in the horizontal plane minimizes the effect of gravity on the behavior of the test structure. The excitation was applied using a linear sine sweep technique. The span of the test structure, the mass of the impact damper, the distance of travel, and the location of the impact damper along the span of the test structure were varied. The damping ratio are estimated for sixty test configurations. The results show that the impact damper significantly increases the damping ratio of the test structure. Statistical analysis of the results using the method of multiple linear regression indicates that a reasonable fit has been accomplished. It is concluded that additional experimental analysis of flexible structures in microgravity environment is needed in order to achieve a better understanding of the behavior of impact damper under conditions of microgravity. Numerical solution of the behavior of flexible structures equipped with impact dampers is also needed to predict stresses and deformations under operating conditions of microgravity in space applications.

Akl, Fred A.↗

Analytical Simulations of Energy-Absorbing Impact Spheres for a Mars Sample Return Earth Entry Vehicle

Nonlinear dynamic finite element simulations were performed to aid in the design of an energy-absorbing impact sphere for a passive Earth Entry Vehicle (EEV) that is a possible architecture for the Mars Sample Return (MSR) mission. The MSR EEV concept uses an entry capsule and energy-absorbing impact sphere designed to contain and limit the acceleration of collected samples during Earth impact without a parachute. The spherical shaped impact sphere is composed of solid hexagonal and pentagonal foam-filled cells with hybrid composite, graphite-epoxy/Kevlar cell walls. Collected Martian samples will fit inside a smaller spherical sample container at the center of the EEV's cellular structure. Comparisons were made of analytical results obtained using MSC.Dytran with test results obtained from impact tests performed at NASA Langley Research Center for impact velocities from 30 to 40 m/s. Acceleration, velocity, and deformation results compared well with the test results. The correlated finite element model was then used for simulations of various off-nominal impact scenarios. Off-nominal simulations at an impact velocity of 40 m/s included a rotated cellular structure impact onto a flat surface, a cellular structure impact onto an angled surface, and a cellular structure impact onto the corner of a step.

Billings, Marcus Dwight↗

The Meteoritic Component in Impact Deposits

An important part of the history of impacts on Earth, and their influence on the terrestrial environment and biotic evolution, is the provenance of the impacting bolides. This will reflect the history of the large-body object flux in the inner solar system. The physical and chemical properties of projectiles, as well as their orbital evolution, has influenced the dynamics and the relative timing of impact events. Possible impact scenarios include random impacts by individual asteroids or comets, or clusters of impacts due to major collisions in the asteroid or Kuiper belts, or large perturbations of the Oort cloud of comets. Over the last several years, a combination of trace element, isotopic, and petrologic data have yielded significant insights into this impact history. The trace element chemistry of sediments, in particular the concentration of siderophiles (e.g., Ir), is a useful tool to detect impacts and provides supporting evidence for suspected impact deposits. However, siderophiles are not especially useful in distinguishing between types of projectiles. Interelement abundances of PGEs can distinguish a chondritic signature, but since most asteroids, and probably all comets are chondritic, these data do little to distinguish between chondritic source materials. Perhaps the most significant chemical argument used to constrain provenance, is that the total amount of Ir in the global Cretaceous-Tertiary (KT) boundary ejecta layer is considerably less than that expected by a low-velocity, 10 km asteroid impact and is most consistent with the impact of a high-velocity, low-Ir comet. Alternatively, much of the Ir may have been buried in the Chicxulub crater and/or ejected to escape velocity.

Kyte, Frank T.↗

Were Ocean Impacts an Important Mechanism to Deliver Meteoritic Organic Matter to the Early Earth? Some Inferences from Eltanin

Several workers have addressed the potential for extraterrestrial delivery of volatles, including water and complex organic compounds, to the early Earth. For example, Chyba and Sagan (1992) argued that since impacts would destroy organic matter, most extraterrestrial organics must be delivered in the fine-fractions of interplanetary dust. More recent computer simulations (Pierazzo and Chyba, 1999), however, have shown that substantial amounts of amino acids may survive the impacts of large (km-sized) comets and that this may exceed the amounts derived from IDPs or Miller-Urey synthesis in the atmosphere. Once an ocean developed on the early Earth, impacts of small ,asteroids and comets into deep-ocean basins were potentially common and may have been the most likely events to deliver large amounts of organics. The deposits of the late Pliocene impact of the Eltanin asteroid into the Bellingshausen Sea provide the only record of a deep-ocean (approx. 5 km) impact that can be used to constrain models of these events. This impact was first discovered in 1981 as an Ir anomaly in sediment cores collected by the USNS Eltanin in 1965 (Kyte et al., 1981). In 1995, Polarstem expedition ANT XII/4 made the first geological survey of the suspected impact region. Three sediment cores sampled around the San Martin seamounts (approx. 57.5S, 91 W) contained well-preserved impact deposits that include disturbed ocean sediments and meteoritic impact ejecta (Gersonde et al., 1997). The latter is composed of shock- melted asteroidal materials and unmelted meteorites. In 2001, the FS Polarstem returned to the impact area during expedition ANT XVIII/5a. At least 16 cores were recovered that contain ejecta deposits. These cores and geophysical data from the expedition can be used to map the effects of the impact over a large region of the ocean floor.

Kyte, Frank T.↗

Impact Melting of Ordinary Chondrite Regoliths and the Production of Fine-grained Fe(sup 0)

The detailed study of individual lunar soil grains provides evidence that the major optical properties of the lunar surface are primarily related to the production of fine-grained (< 20 nm, super-paramagnetic) Fe-particles in agglutinitic impact melts and to iron-rich vapor deposits on the surfaces of individual grains. These Fe-rich materials are derived from oxidized species due to high post-shock temperatures in the presence of solar-wind derived H2; part of the Fe-rich grain surfaces may also be due to sputtering processes. Identical processes were recently suggested for the optical maturation of S-type asteroid surfaces, the parent objects of ordinary chondrites (OCs). OCs, however, do not contain impact-produced soil melts, and should thus also be devoid of impact-triggered vapor condensates. The seeming disparity can only be understood if all OCs resemble relatively immature impact debris, akin to numerous lunar highland breccias. It is possible to assess this scenario by evaluating experimentally whether impact velocities of 5- 6 km/s, typical for the present day asteroid belt, suffice to produce both impact melts and fine-grained metallic iron. We used 125-250 m powders of the L6 chondrite ALH85017. These powders were aliquots from fines that were produced by collisionally disrupting a single, large (461g) chunk of this meteorite during nine impacts and by subjecting the resulting rubble to an additional 50 impacts. As a consequence, the present shock-recovery experiments employ target materials of exceptional fidelity (i.e., a real chondrite that was impact pulverized). The target powders were packed into tungsten-alloy containers to allow for the potential investigation of freshly produced, fine-grained iron and impacted by stainless-steel and tungsten flyer plates; the packing density varied between 38 and 45% porosity. Peak pressures ranged from 14.5 to 67 GPa and were attained after multiple reverberations of the shock wave at the interface of the silicate powder and metal container. Pressures in the 50 to 70 GPa range should be fairly typical for asteroid impacts at approx. 5-6 km/s, yet we note that these pressures refer to those at the projectile/target interface only and that most crater ejecta on OC parent-bodies will have experienced much lower stresses.

Hoerz, Friedrich↗

Lunar and Planetary Science XXXV: Impacts: Modeling and Observations

This document covers the following topics: Cratering on Titan: Projectiles, Craters and Impact Melt; The Cratering Database: Making Code Jockeys Honest; Popigai Impact Structure Modeling: Morphology and Worldwide Ejecta; Anhydrite EOS and Phase Diagram in Relation to Shock Decomposition; Computational Investigations of the Chesapeake Bay Impact Structure; Hydrocode Simulations of the Chesapeake Bay Impact; Lockne Crater as a Result of Oblique Impact; The Influence of a Deep Shelf Sea on the Excavation and Modification of a Marine-Target Crater, the Lockne Crater, Central Sweden; Pre-Drilling Investigation of the Lake Bosumtwi Impact Crater: Constraints from Geophysics and Numerical Modelling; Central Uplift Formation at the Middlesboro Impact Structure, Kentucky, USA; A SRTM Investigation of Serra da Cangalho Impact Structure, Brazil; Brazilian Impact Craters: A Review; Flynn Creek Impact Structure: New Insights from Breccias, Melt Features, Shatter Cones, and Remote Sensing; The Howell Structure, Lincoln County, Tennessee: A Review of Past and Current Research; After the Chicxulub Impact: Control on Depositional and Diagenetic History of the Cenozoic Carbonate Formations of the Northwestern Yucatan Peninsula, Mexico; Ni Contents by Non-Destructive In-Situ XRF Method of Takamatsu-Kagawa Crater District in Japan; and Akiyoshi Limestone Blocks Transported by the P/T Boundary Event to Japan Islands.

Source record↗

Impacts and evolution: future prospects

The discipline of astrobiology includes the dynamics of biological evolution. One of the major ways that the cosmos influences life is through the catastrophic environmental disruptions caused when comets and asteroids collide with a planet. We now recognize that such impacts have caused mass extinctions and played a major role in determining the evolution of life on Earth. The time-averaged impact flux as a function of projectile energy can be derived from lunar cratering statistics as well as the current population of near Earth asteroids (NEAs). Effects of impacts of various energies can be modeled, using data from historic impacts [such as the Cretaceous-Tertiary (KT) impactor 65 million years ago] and the observed 1994 bombardment of Jupiter by fragments of Comet Shoemaker-Levy 9. It is of particular interest to find from such models that the terrestrial environment is highly vulnerable to perturbation from impacts, so that even such a small event as the KT impact (by a projectile 10-15 km in diameter) can lead to a mass extinction. Similar considerations allow us to model the effects of still smaller (and much more likely) impacts, down to the size of the asteroid that exploded over Tunguska in 1908 (energy approximately 10 megatons). Combining the impact flux with estimates of environmental and ecological effects reveals that the greatest contemporary hazard is associated with impactors near 1 million megatons in energy (approximately 2 km in diameter for an asteroid). The current impact hazard is significant relative to other natural hazards, and arguments can be developed to illuminate a variety of public policy issues. The first priority in any plan for defense against impactors is to survey the population of Earth-crossing NEAs and project their orbits forward in time. This is the purpose of the Spaceguard Survey, which has already found more than half of the NEAs >1 km in diameter. If there is an NEA on a collision course with Earth, it can be discovered and the impact predicted with decades or more of warning. It is then possible to consider how to deflect or disrupt the NEA. Unlike other natural hazards, the impact risk can be largely eliminated, given sufficient advanced knowledge to take action against the threatening projectile.

Directed Molecular Evolution↗

Summary of Results from Analyses of Deposits of the Deep-Ocean Impact of the Eltanin Asteroid

Deposits of the late Pliocene (2.5 Ma) Eltanin impact are unique in the known geological record. The only known example of a km-sized asteroid to impact a deep-ocean (5 km) basin, is the most meterorite-rich locality known. This was discovered as an Ir anomaly in sediments from three cores collected in 1965 by the USNS Eltanin. These cores contained mm-sized shock-melted asteroid materials and unmelted meteorite fragments. Mineral chemistry of meteorite fragments, and siderophole concentrations in melt rocks, indicate that the parent asteroid was a low-metal (4\%) mesosiderite. A geological exploration of the impact in 1995 by Polarstern expedition ANT-XIV4 was near the Freeden Seamounts (57.3S, 90.5 W), and successfully collected three cores with impact deposits. Analyses showed that sediments as old as Eocene were eroded by the impact disturbance and redeposited in three distinct units. The lowermost is a chaotic assemblage of sediment fragments up to 50 cm in size. Above this is a laminated sand-rich unit that deposited as a turbulent flow, and this is overlain by a more fine-grained deposit of silts and clays that settled from a cloud of sediment suspended in the water column. Meteoritic ejecta particles were concentrated near the base of the uppermost unit, where coarse ejecta caught up with the disturbed sediment. Here we will present results from a new suite of cores collected on Polarstern expedition ANT-XVIIU5a. In 2001, the Polarstern returned to the impact area and explored a region of 80,000 sq-km., collecting at least 16 sediment cores with meteoritic ejecta. The known strewn field extends over a region 660 by 200 km. The meteoritic ejecta is most concentrated in cores on the Freeden seamounts, and in the basins to the north, where the amount of meteoritic material deposited on the ocean floor was as much as 3 g/sq-cm. These concentrations drop off to the north and the east to levels as low as approximately 0.1 g/sq-cm. We were unable to sample the impact south and west of the seamounts, as the deposit was buried beyond the reach of our 25 m piston corer. We estimate that ground zero was in the region just north, or northwest, of the seamounts. There is no evidence that the impactor penetrated the ocean floor or formed a crater. The composition of the melted ejecta is inconsistent with mixing between projectile and terrestrial materials other than seawater salts. X-ray radiographs of sediments reveal details not seen in earlier cores. The uppermost impact unit is well-preserved in several cores, found as much as 50 km from the seamounts to the east, north, and west of the seamounts, where at least 25 cm of this unit is preserved. At greater distances burrowing organisms have mixed the sediments so if this unit did exist, it was too thin to survive bioturbation. These finegrained sediments are clearly laminated, and show alternating layers of low- and high-density (meteoritic) sediments, consistent with ripple formation in an energetic flow regime. We have extracted 35 g of meteoritic melt rock and 3 g of meteorite fragments from sieved sediments. Additionally a 9 g, 2.2 cm meteorite was recovered during opening of one core. The fact that 9\% of the coarse ejecta is unmelted meteorites may be characteristic of deep-ocean impacts. This may have significance for delivery of organic matter to the early Earth by small impacts into primordial oceans, where actual meteorite fragments can survive in significant amounts. However, a large portion of the meteoritic debris is buried rapidly by the sediments disturbed by the impact.

Kyte, Frank T.↗